www.electrak.co.uk 12 Electrak quick fit floor service outlet boxes Tel: 01207 503400 Fax: 01207 501799 Email: sales@electrak.co.uk Because of our policy of continuous improvement, Electrak reserves the right to change product specification without notice.
in this section: 13 2 compartment 3 compartment 4 compartment quick fit in less than 10 seconds
2, 3 & 4 compartment floor service outlet boxes Electrak has produced the Quick Fit Floor Service Outlet Box to meet the demands of the modern working environment. Supplied in parts or fully assembled and configured to customer specification. The 2, 3 and 4 compartment floor box provides fast installation with simple tool-free fixing mechanisms. 14 2 compartment (290mm x 230mm) This box size can also be supplied in 3 compartment 3 compartment (366mm x 230mm) 2, 3 & 4 compartment boxes are also available with separate individual compartment base units. Convenient for offsite pre-wiring features... Tool-free fixing Easy removal of lid and trim assembly for carpet fitting Reversible self closing lid High quality construction withstands 4KN-point load test Lid retention latches Carpet retention spikes Cable outlet retention latches 2, 3 or 4 compartment boxes Any type of accessory plates Fast Installation 4 compartment (366mm x 230mm) benefits... The box (with or without tap-off unit) only needs to be pushed down into the floor aperture to secure it. Easy Access For Carpet Fitting The lid and trim is removed in seconds by lifting the locking handles and is pushed back in place after carpet fitting. Easy Installation of Services The lid and trim assembly quick release mechanism permits fast access to all compartments for the installation of services. Can be pre-fitted with socket outlet and tap-off unit.
quick fit in seconds... To install box: Cut the hole in the raised floor tile, lower the complete box into the aperture and push firmly down. 15 To fit carpet: Detach the lid and trim assembly by lifting the blue locking handles and lifting out. Cut and fit the carpet. Push the lid and trim assembly back into place. Box in place
buyer s guide 2 compartment floor box and accessory plates 3 & 4 compartment floor box and accessory plates Firstly order the Floor Box to suit the depth of raised floor and the number of plates that you require. Secondly choose the accessory plates to match your power, data and voice requirements. 2 compartment 290mm 230mm 3 compartment 366mm 230mm 4 compartment 366mm 230mm 16 Description 112mm Width Plates 100mm Width Plates 75mm Width Plates Floor service box single base - 75mm depth CR2001 CR011 CR4001 Floor service box single base - 85mm depth (standard box) CR2002 CR012 CR4002 Floor service box single base - 110mm depth CR2003 CR013 CR4003 Floor service box separate compartment base - 75mm depth CR2004 CR014 CR4004 Floor service box separate compartment base - 85mm depth CR2005 CR015 CR4005 Floor service box separate compartment base - 110mm depth CR2006 CR016 CR4006 Blank Plate CR2100 CR020 CR4100 2 gang switched socket outlet with plate CR2101 CR022 CR4101 2 gang switched socket outlet with plate, low noise 607 CR2102 CR023 CR4102 2 gang unswitched socket outlet with plate CR2104 CR029 CR4104 3 gang unswitched socket outlet with plate CR2105 CR030 CR4105 2 gang RCD socket outlet CR2112 CR036 CR4111 Punched plate for 2 x 1 gang accessories (60.3mm fixing centres) CR2106 CR026 N/A Punched plate for 2 gang accessories (120.6mm fixing centres) CR2107 CR028 N/A 2 x LJ2 accessory plate (50mm centres) N/A CR031 CR4106 4 x BNC connector plate CR2109 CR033 CR4108 4 x Data / Telecom plate (37mm x 22mm cut outs) CR2113 CR024 CR4112 6 x Data / Telecom plate (37mm x 22mm cut outs) CR2114 CR025 CR4113 pre-wired floor box to electrak tap off units socket outlet and tap off DP1332 socket outlet and tap off DP1532 socket low noise and tap off JP2332 socket outlet low noise and tap off JP2532 CR100 CR101 CR110 CR111 socket outlets and tap off DP1332 socket outlets and tap off DP1532 socket outlets, low noise and tap off JP2332 socket outlets, low noise and tap off JP2532 CR122 CR123 CR132 CR133
Lid Cable outlets Locking handles (Blue) Single base 2,3 or 4 compartment Cable routers Locking handle fixing grommet Trim 17 Floor tile fixing latch A Base Max Radius 2.5mm Separate 2, 3 or 4 compartment base Other accessory plates available upon request. Please state manufacturer of data / telecom module when ordering, as cut out sizes may vary. Floor Boxes are available pre-wired with any Electrak tap-off unit. See page 11. Mounting Frame floor tile cutout dimensions 2 compartment 263mm x 203mm* 3 and 4 compartment 340mm x 203mm* *The aperture dimension 203mm has a fixing tolerance between 203 to 205mm Floor cut-out aperture the same for single base or separate compartment base dimensions Lid can accommodate carpets up to 6mm depth. Accessory plates are 172mm long, with 162mm fixing centres. Dimensions from top of floor tile into void underfloor C A For information on Electrak tap-offs and other floor box configurations contact the Sales department at Electrak tel: 01207 503400 Email: sales@electrak.co.uk or visit our website www.electrak.co.uk spares and additional parts Description Catalogue Number Floor Tile Cutout Template 2 compartment CR0001 Floor Tile Cutout Template 3/4 compartment CR0003 Cable Outlet Flap (Pack 10) CR0000 Cable Routers (Pack 10) CR0010 Screws for Accessory Plates (Pack 50) CR0011 Lid 2 compartment box Lid 3/4 compartment box Mounting Frame for Vinyl Floor 2 compartment box replaces mounting frame attached to base Mounting Frame for Vinyl Floor 3/4 compartment box replaces mounting frame attached to base CR0002 CR0004 CR0005 CR0006 A B C Accessory Underside lid to top of Box Depth accessory (plug clearance) 75mm 85mm 110mm materials 35mm 45mm 45mm 35mm 35mm 60mm Lid and trim mouldings are precision engineered from hard wearing durable Nylon 6. The lid is reinforced with a Zintec coated mild steel plate. Mounting frame and box base - 0.9mm thick galvanised steel. wiring Each compartment has 2 entries for 20mm and 2 entries for 25mm flexible conduits. colour Standard colour of mouldings Grey Alternative colours available as special order. Plates goosewing grey. B