MPX-CD16P MPX-MD16P INSTRUCTION MANUAL. Multiplexer. Multiplexer. Multiplexeur. Multi distributore. English GB. Deutsch D. Français F.

Transcription

1 INSTRUCTION MANUAL MPX-CD16P MPX-MD16P Multiplexer English GB Multiplexer Deutsch D Multiplexeur Français F Multi distributore Italiano I About this manual Before installing and using the camera, please read this manual carefully. Be sure to keep it handy for later reference. This manual gives basic connections and operating instructions for 2 models (Colour MPX-CD16P, B/W MPX-MD16P). Über diese Bedienungsanleitung Lesen Sie bitte vor der Montage und dem Inbetriebnehmen der Kamera zuerst diese Bedienungsanleitung sorgfältig durch und bewahren Sie sie zum späteren Nachschlagen auf. In dieser Anleitung finden Sie die Anschlüsse und die Grundbedienung für 2 Modelle (Farbe: MPX-CD16P, Schwarzweiß: MPX-MD16P). À propos de ce manuel Avant d'installer et d'utiliser la caméra, veuillez lire ce manuel attentivement. Gardez-le à portée de main pour toute référence ultérieure. Ce manuel couvre les branchements et instructions pour l utilisation de base pour 2 modèles (Couleur: MPX-CD16P, noir et blanc: MPX-MD16P). Nota su questo manuale Prima di procedere all installazione ed all uso dell apparecchio, leggere attentamente questo manuale di istruzioni, e conservarlo per ogni eventuale futura consultazione. Il manuale contiene le istruzioni per i collegamenti ed il funzionamento di due tipi di modelli, l MPX-CD16P (a colori) e l MPX-MD16P (in bianco e nero).

2 PRECAUTION WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR OTHER MOISTURE. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. If the power supply cord (AC power cord) of this appliance is damaged, it must be replaced. Return to a SANYO Authorised Service Centre for replacement of the cord. Location For safe operation and satisfactory performance of your Multiplexer, keep the following in mind when selecting a place for its installation: Shield it from direct sunlight and keep it away from sources of intense heat. Avoid dusty or humid places. Avoid places with insufficient ventilation for proper heat dissipation. Do not block the ventilation holes at the top and bottom of the Multiplexer. Do not place the unit on a carpet because this will block the ventilation holes. Install the Multiplexer in a horizontal position only. Avoid locations subject to strong vibrations. Avoid moving the Multiplexer between cold and hot locations. Do not place the Multiplexer directly on top of the TV, as this may cause playback or recording problems. IMPORTANT NOTE (U. K. Only) The wires in the mains lead are coloured according to the following code: Blue: Neutral Brown: Live If the colours of the wires in the mains lead of this apparatus do not correspond with the colour markings identifying the terminals in your plug, proceed as follows: The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured blue or black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured brown or red. Do not connect either wire to the Earth terminal. Avoiding Electrical Shock and Fire Do not handle the power cord with wet hands. Do not pull on the power cord when disconnecting it from an AC wall outlet. Grasp it by the plug. If any liquid is spilled on the Multiplexer, unplug the power cord immediately and have the unit inspected at a factory-authorised service centre. Do not place anything directly on top of this Multiplexer. SERVICE This unit is a precision instruments and if treated with care, will provide years of satisfactory performance. However, in the event of a problem, the owner is advised not to attempt to make repairs or open the cabinet. Servicing should always be referred to your dealer or Sanyo Authorized Service Centre. English 1

3 CONTENTS FEATURES...2 ACCESSORIES...2 LOCATION OF CONTROLS AND INDICATORS Front Panel...3 Back Panel...4 CONNECTIONS...5 ASSEMBLING THE DIN 25-PIN PLUG...6 ON-SCREEN MENUS...7 CLOCK SETUP...8 TITLE SETUP...9 ALARM SETUP...10 CLOCK, TITLE DISPLAY...11 VCR SETUP...12 ALARM DATA DISPLAY...13 CAMERA SCREEN DISPLAY CONTROL...14 Split Screen Viewing...15 x2 Zoomed In Image Viewing...15 Freezed Image Viewing...15 Full Screen Image Viewing...16 Full Screen Sequential Viewing...16 Camera Live Picture and VCR Playback Picture Simultaneous Viewing...17 Playback on Monitor Monitor 2 Display Setup...18 ALARMS Alarm Display During Camera Live Picture Viewing...19 Alarm Display During VCR Playback...19 VCR PLAYBACK SCREEN DISPLAY CONTROL...20 Split Screen Viewing...21 x2 Zoomed In Image Viewing...21 Freezed Image Viewing...21 Full Screen Image Viewing...22 Full Screen Sequential Viewing...22 VCR Recorded Picture and Camera Live Picture Simultaneous Viewing...23 SPECIFICATIONS...24 FEATURES Settings entered by on-screen menus Clock settings, Titles, Alarms, On-screen displays, Recording mode, Alarm data Monitor 1 output screen Split screen (divided in 16, 13, 10, 7, 4), full screen, sequence display, 2 times zoom (with selectable range), still image Monitor 2 output screen Full screen, sequence display Camera title display (8 characters) Time display S-VIDEO output/input terminals (MPX-CD16P only) ACCESSORIES Power cord DIN 25-pin assembled plug DIN 25-pin plug components Cover nut Locking screw E-rings ENGLISH Plug plate Shielded cover A Shielded cover B 2 English

4 LOCATION OF CONTROLS AND INDICATORS Front Panel F G 2 H 1 Power ON switch and indicator 2 STAND BY indicator This indicator will come on when the power cord is connected in a live power outlet. It will go off when the unit is turned on. 3 Camera SELECT buttons and indicators 4 Reset button When this button is pressed, the unit is turned off and the date and time are reset. 5 PLUS1 (Monitor 2 image switching) button and indicator 6 STILL image button and indicator 7 ZOOM button and indicator 8 SEQUENCE select button and indicator 9 MULTI (Screen splitting) button and indicator F LIVE camera signal select button and indicator G VCR signal select button and indicator H MENU button Press this button to display the main menu. Buttons 7, 8, 9, F and G are used for menu control (for more information, please refer to page 7). Resetting the menus If the unit is moved, or to cancel all previously entered settings, reset the menus as indicated below. (1) Turn the unit off. (2) Keep the MENU button pressed down, then press the ON button. Reset the menus only if it is absolutely necessary. Resetting the menus will erase the settings previously entered, and will also affect the internal clock. Button Lock Function This unit is equipped with a function that lets you lock the buttons to prevent any undesired operation during camera live mode or VCR playback mode. While the Button lock function is engaged, a buzzer will sound when one of the buttons corresponding to each lock mode is pressed. Button lock for camera mode Press and hold the LIVE button then press the power ON switch. The ON, VCR and MENU buttons will be locked, and a buzzer will sound if they are pressed. LIVE Button lock for VCR playback mode Press and hold the VCR button then press the power ON switch. The ON, LIVE and MENU buttons will be locked, and a buzzer will sound if they are pressed. VCR ON ON ON ON VCR LIVE MENU MENU To cancel the Button lock function Press and hold the LIVE or VCR button then press the power ON switch. English 3

5 LOCATIONS OF CONTROLS AND INDICATORS Back Panel S-VIDEO 2 4 9F G H 2 I 1 Camera IN (Camera input) terminal (Control terminal) 2 Camera OUT (Camera output) terminal 3 S-VIDEO IN (Input) terminal 4 S-VIDEO OUT (Output) terminal 5 VCR IN (Video cassette recorder input) terminal 6 VCR OUT (Video cassette recorder output) terminal 7 MONITOR OUT 1 (Monitor TV 1 output) terminal 8 MONITOR OUT 2 (Monitor TV 2 output) terminal 9 AL OUT (Alarm output) terminal F COM (Common) terminal G SW IN (Switch input) terminal H CONTROL terminal I AC Power input NOTE: Model MPX-MD16P does not have S-VIDEO IN, OUT terminals. No. Signal No. Signal 1 Alarm input 1 14 Alarm input 14 2 Alarm input 2 15 Alarm input 15 3 Alarm input 3 16 Alarm input 16 4 Alarm input 4 17 GND 5 Alarm input 5 18 No operation 6 Alarm input 6 19 No operation 7 Alarm input 7 20 No operation 8 Alarm input 8 21 GND 9 Alarm input 9 22 No operation 10 Alarm input GND 11 Alarm input Remote control 1 input 12 Alarm input Remote control 2 input 13 Alarm input 13 By connecting the remote control pins (24 and 25) of the CONTROL terminal to a remote control circuit, remote controlled operation of this unit is possible. 4 English

6 CONNECTIONS Before making any connection, make sure the power has been turned off on all the devices. NOTES: If a connection is made to the S-VIDEO terminal, the (S-VIDEO) signal will have the priority. For detailed information, please refer to the manuals accompanying the other connected devices. Make sure all the connections are correct, if not that may cause a fire and/or damages. Model MPX-MD16P does not have S-VIDEO IN, OUT terminals. With model MPX-MD16P, use black and white cameras only. If colour cameras are used, that may cause image beat, etc. Monitor (sold separately) Video cameras (sold separately) Video input connector Video input connector Signal flow : VIDEO IN : VIDEO OUT : CAMERA IN Video input terminal To outlet Video output terminal S-video output terminal S-VIDEO Timelapse VCR (sold separately) S-video input terminal COM terminal Switch output terminal Alarm input terminal To pin 24 To pin Ω SW 1: Camera Ω SW 2: Camera Ω SW 3: Camera Ω SW 4: Camera Ω SW 5: Camera Ω SW 6: Camera Ω SW 7: Camera kω SW 8: Camera kω SW 9: Camera kω SW10: Camera kω SW11: Camera kω SW12: Camera kω SW13: Camera kω SW14: Camera kω SW15: Camera kω SW16: Camera 16 To pin Ω SW17: MENU 220 Ω SW18: VCR 300 Ω SW19: LIVE 360 Ω SW20: MULTI 470 Ω SW21: PLUS Ω SW22: SEQUENCE 820 Ω SW23: ZOOM 1.2 kω SW24: STILL 1.8 kω SW25: POWER To pin 1 To pin 2 To pin 3 To pin 4 To pin 5 To pin 6 To pin 7 To pin 8 To pin 9 To pin 10 To pin 11 To pin 12 To pin 13 To pin 14 To pin 15 To pin 16 To pin 21 Remote controller circuit To pin 17 Alarm sensor (door bell, interphone, etc.) English 5

7 ASSEMBLING THE DIN 25-PIN PLUG 1 Preparing the cable 1 Insert the cable in the cover nut (A), then remove the cable sleeve as shown. A 3 Installing the covers 1 Insert plug plate (C) in the cover (B) slot. Check that the shielding tape is within about 2 3 mm from the end of the cover (B). Push in the cover (B) tabs. 2~3 mm 30 mm 2 Return the metallic shield mesh on the cable as shown and cut it. C 10 mm 3 For better shielding results, wrap about 20 mm of copper or aluminium tape. B 2 Align the cover (D) slot with the plug plate (C) and push down until the clasps (E) interlock. Tighten securely the cover nut (A) on the covers threads. D 2 Soldering the leads Remove about 2 mm of sleeve from the end of each leads. Apply solder on the extremity of the leads, then solder them to the plug. (For the pins number and signal, please refer to page 4.) 2 mm C E 3 Insert the locking screws (F) in the holes, then fix them by inserting the E-ring (G) between the cover (D) and the plug plate. Bend the holder (H) 2 or 3 times until it breaks off. Following the same procedure, install the E-ring on the other side. A F F D H G 4 When the DIN plug is assembled, connect it to the CONTROL terminal, then affix it using the locking screws. 6 English

8 ON-SCREEN MENUS To display the main menu, or return to the main menu from a sub-menu, press the MENU button. To select the different sub-menus, and enter the settings use the m,, +, O, or «buttons. When a menu is displayed, the indicators corresponding to the buttons that can be used with that particular menu will light. Buttons functions Button m : To accept a setting. Button : To select in reverse order, numbers, letters, symbols. To switch selectable settings. Button + : To select in order, numbers, letters, symbols. To switch selectable settings. Button O : To move down. Button «: To move the right. NOTES: When displaying the menus, start with camera signals and VCR playback signals displayed together in a split screen, full screen, or sequence display. The menus setup screens are displayed on the monitor connected to the MONITOR OUT 1 terminal. Monitor 1 screen CLOCK SET menu TITLE SET menu Title input screen ALARM SET menu Menu screen DISPLAY SET menu Clock display location selection screen VCR recording SET menu * If a camera is not connected to a camera input terminal, the message NO VIDEO will appear. ALARM DATA screen English 7

9 CLOCK SETUP Menu 1 Setting Example: To set the clock to October 15, 1997 at 15:20 PM. 1 Press the MENU button, make sure 1. CLOCK SET is selected, then press the MENU button again. 2 Press the + (or ) button to set the day (15), then press the «button. Following the same procedure, set the month (10), the year (97), the hours (15) and the minutes (20). For accurate clock setting, press the button together with a time broadcast signal or other accurate time signal, then press the O button. The seconds will start counting from Press the + (or ) button to set the SUMMER TIME to STANDARD or SUMMER, then press the O button. 4 Press the MENU button, then press the O button to select 7. ENTER and press the MENU button again. Concerning the Clock Display The clock is displayed as indicated below. For more information on how to display the clock, please refer to CLOCK, TITLE DISPLAY on page 11. Split screen (16 divisions) Split screen (4 divisions) Full screen 8 English

10 TITLE SETUP Menu 2 Setting Example: To set the title GATE 5F for the camera 5. 1 Press the MENU button, then press the O button to select 2. TITLE SET. 2 Press the MENU button, then press the O button to select 5 and press the m button. 3 Press the + (or ) button to set the first character G, then press the «button. Following the same procedure, set the title GATE 5F, then press the m button. 4 Press the MENU button, then press the O button to select 7. ENTER and press the MENU button again. Concerning the Title Display The title is displayed as indicated below. For more information on how to display the title, please refer to CLOCK, TITLE DISPLAY on page 11. Split screen (16 divisions) Split screen (4 divisions) Full screen English 9

11 ALARM SETUP Menu 3 Setting Press the MENU button, then press the O button to select 3. ALARM SET. 2 Press the MENU button. 3 Press the + (or ) button to select the desired setting for BUZZER, then press the O button. Following the same procedure, select the desired settings for DURATION, RETRIGGER, MONITOR1 ZOOM, MONITOR1 STILL, MONITOR2 OUT, VIDEO LOSS. (For more information on each setting, please refer to Alarm Settings below.) 4 Press the MENU button, then press the O button to select 7. ENTER and press the MENU button again. Alarm Settings BUZZER ON: The buzzer will sound when there is an alarm trigger. OFF: The buzzer will not sound. DURATION 10SEC, 20SEC, 30SEC, 40SEC, 50SEC, 60SEC: Duration of the alarm. CC: The alarm will go on as long as the alarm signal is received (minimum 10 second). RETRIGGER ON: If a second alarm trigger is received during the alarm operations for that same alarm number, then it will also be received. OFF: During the alarm operations for an alarm number, any alarm trigger at the same alarm number will be ignored. MONITOR1 ZOOM ON: When an alarm trigger is received, the image displayed on monitor 1 will be zoomed in. If the alarm trigger was recorded on tape, the zoom function will not operate. OFF: The zoom function will not operate. MONITOR1 STILL ON: When an alarm trigger is received, the image displayed on monitor 1 will be freezed. If the alarm trigger was recorded on tape, the still function will not operate. OFF: The still function will not operate. MONITOR2 OUT ON: When an alarm trigger is received, the image from the camera corresponding to the alarm trigger is displayed on monitor 2. When 2 or more alarm triggers are received simultaneously, monitor 2 will display sequentially all the images from the cameras corresponding to the alarm triggers. OFF: The monitor 2 output function will not operate. VIDEO LOSS ON: An alarm is generated if there is loss of the video signal. The display on monitor 1 will automatically switch to 16 divisions split screen, A will be displayed for the camera where the loss of video signal occurred and the ALARM DURATION will be 30 seconds. This alarm will not be included in the ALARM DATA display. OFF: An alarm is not generated if there is loss of the video signal. 10 English

12 CLOCK, TITLE DISPLAY Menu 4 1 Press the MENU button, then press the O button to select 4. DISPLAY SET and press the MENU button again. 2 Press the + (or ) button to select ON for LIVE CLOCK, then press the m button. 3 Press the O button to set the clock display position, then press the m button. Press the O button to select LIVE TITLE, then press the + (or ) button to select ON or OFF as desired. Refer to Display Settings below, then following the same procedure, set VCR PB CLOCK, VCR PB TITLE, MON1 SEQ. TIMER, MON2 SEQ. TIMER and MONITOR2ÜMONITOR1 as desired. NOTE: If the displays on the monitor overlap each other, cancel the timelapse VCR display. 4 Press the MENU button, then press the O button to select 7. ENTER and press the MENU button again. Display Settings LIVE CLOCK ON: The clock is displayed when the signals from a camera are displayed. (To set the clock, please refer to CLOCK SETUP.) OFF: The clock is not displayed when the signals from a camera are displayed. LIVE TITLE ON: The title is displayed when the signals from a camera are displayed. (To set a title, please refer to TITLE SETUP.) OFF: The title is not displayed when the signals from a camera are displayed. VCR PB CLOCK ON: The clock is displayed when the signals from the VCR playback are displayed. OFF: The clock is not displayed when the signals from the VCR playback are displayed. VCR PB TITLE ON: The title is displayed when the signals from the VCR playback are displayed. OFF: The title is not displayed when the signals from the VCR playback are displayed. MON1 SEQ. TIMER 0.5 to 30 SEC (in 0.5 sec increments): The timing of the sequential display on monitor 1. MON2 SEQ. TIMER 0.5 to 30 SEC (in 0.5 sec increments): The timing of the sequential display on monitor 2. MONITOR2 MONINTOR1 To have the same display on monitor 2 as the one on monitor 1. English 11

13 VCR SETUP Menu 5 Setting Press the MENU button, then press the O button to select 5. VCR SET. 2 Press the MENU button. 3 Press the + (or ) button to select the desired setting for VCR MODE, then press the O button. Following the same procedure, select the desired settings for VCR OUT, VCR REC SPEED, VCR ALARM REC SPEED, POSITION. (For more information on each setting, please refer to VCR Settings below.) 4 Press the MENU button, then press the O button to select 7. ENTER and press the MENU button again. VCR Settings VCR MODE Set the mode according to the type of VCR connected to the unit. SP: When using a timelapse VCR. LP: When using a real time VCR. VCR OUT Set the VCR OUT 1 or 3 described below in order to get the clear picture when the real time VCR is connected. When SP is selected for the VCR MODE, the VCR OUT setting is then fixed to 1. When LP is selected for the VCR MODE, the VCR OUT setting can be switched between 1 and 3. 1: The unit will switch the input to the next camera after one (1) image is output. 3: The unit will switch the input to the next camera after three (3) images are output. VCR REC SPEED Set the duration according to the VCR recording speed. SP: 3H, 12H, 24H, 48H, 72H, 96H, 120H, 168H, 240H, 360H, 480H, 720H, 960H LP: 6H, 18H, 30H, 48H, 72H, 96H, 120H, 168H, 240H, 360H, 480H, 720H, 960H The duration indicated is for when using an E-180 tape. Real time VCRs use E-240 tapes, therefore the durations will be as indicated by the examples below. VCR ALARM REC SPEED Set the duration according to the VCR alarm recording duration. SP: 3H, 12H, 24H, NC, F3H LP: 6H, 18H, NC, F6H NC: During alarm recording on the timelapse/real time VCR, the recording speed will remain the same. When using the SW signal Some Timelapse/real time VCRs do not output a SW signal in 3H mode, therefore in order to keep the same recording speed as the connected VCR, set this unit as follows. Set VCR REC SPEED to 3H. When using an alarm recording of 3H (or 6H in LP mode), set VCR ALARM REC SPEED to F3H (or to F6H in LP mode). If using a timelapse/real time VCR with a switching output (SW OUT) function, then set FIELD to 01, TIMING to FIELD, 3H to Y (Yes). POSITION : Will switch when the signal at the SW IN terminal goes to High. : Will switch when the signal at the SW IN terminal goes to Low. Set duration (based on a E-180 tape) 6H 18H 30H Real time VCR recording duration (based on a E-240 tape) 8H 24H 40H 12 English

14 ALARM DATA DISPLAY Menu The ALARM DATA display will indicate the alarm trigger input camera number, date and time. The data for the last 100 alarm triggers can be displayed. 1 Press the MENU button, then press the O button to select 6. ALARM DATA. 2 Press the MENU button. 3 Press the m button to display the following pages. 4 Press the MENU button, then press the O button to select 7. ENTER and press the MENU button again. NOTE: The illustrated alarm data menus show examples of alarm triggers inputs. English 13

15 CAMERA SCREEN DISPLAY CONTROL When the unit is turned on, all the camera indicators (1 16), the LIVE indicator and the MULTI indicator will come on. A 16 divisions split screen will appear on monitor 1, and the image from camera 1 will be displayed full screen on monitor 2. (Monitor 2) b For split screen viewing (Monitor 1) b For zoomed in viewing b Freezed frame viewing b For full screen viewing (x2 zoom) (Freeze frame) b For full screen sequential viewing b For 4 split screen sequential viewing (Monitor 2) b For simultaneous camera live and VCR playback viewing (VCR playback image) 14 English

16 CAMERA SCREEN DISPLAY CONTROL Monitor 1 Split Screen Viewing By pressing the MULTI button, you can select one of the 8 split screen combinations. The camera indicators corresponding to the cameras displayed on-screen come on. NOTES: The unit will remember the selected screen display, and when turned on again it will automatically go back to the screen display combination selected before it was turned off. If a camera is not connected to certain Camera IN terminals, NO VIDEO will be displayed for the corresponding screen(s). x2 Zoomed In Image Viewing Example: To watch the image from camera 14 at x2 zoom. 1 Press the ZOOM button, then press the camera SELECT (14) button. The image will be zoomed in, and Z will flash instead of the camera number (14). (The ZOOM indicator and the camera (14) indicator will flash.) To cancel the zoom mode, press the ZOOM button one more time. The image can also be zoomed in when the screen is split in 4. 2 To switch to full screen display and to set the zoomed in image position. While in zoom mode ( Z displayed), press the camera SELECT (14) button for about 3 seconds. The zoomed image will be displayed full screen, and SET will be displayed. Using the following buttons adjust the zoomed in image position. Button O : To lower the image. Button «: To move the image towards the right. NOTES: About 10 seconds after having set the image position, the display will automatically return to the original split display. The zoomed in image position is memorized and it will return to that position the next time the zoom function is used. The zoom in image position set function can be used from split or full screen display. 3 To freeze a zoomed in image. While in zoom mode ( Z displayed), press the STILL button, then press the camera SELECT (14) button. You can then view a zoomed in freezed image, and ZS will flash. To return to normal zoomed in mode, press the camera SELECT (14) button. To return to normal viewing mode, press the STILL button, then press the ZOOM button. S Freezed Image Viewing Example: To freeze the image from camera 7. Press the STILL button, then press the camera SELECT (7) button. You can then view a freezed image, and S will flash instead of the camera number (7). To return to normal viewing mode, press the STILL button again. STILL 7 English 15

17 CAMERA SCREEN DISPLAY CONTROL Monitor 1 Full Screen Image Viewing From the split screen display, press a camera SELECT button and the image from that camera will be displayed full screen. To return to split screen display, press the MULTI button. While viewing a full screen display, the following operations are available. 1 x2 Zoomed In Image Viewing Press the ZOOM button. The image will be zoomed in and Z will flash instead of the camera number. While in zoom mode ( Z displayed), press the STILL button. You can then view a zoomed in freezed image, and ZS will flash. During zoom mode, the ZOOM indicator will flash. While the zoomed in image is freezed, the ZOOM indicator will light and the STILL indicator will flash. To return to normal zoomed in mode, press the STILL button. To return to normal viewing mode, press the ZOOM button. 2 Freezed Image Viewing Press the STILL button. You can then view a freezed image and S will flash instead of the camera number. While the image is freezed, the STILL indicator will flash. To return to normal viewing mode, press the STILL button again. Full Screen Sequential Viewing From the full screen display, press the SEQUENCE button to display the images full screen, switching sequentially. The SEQUENCE indicator will light, and the MULTI indicator will go off. To return to split screen display, press the MULTI button. NOTES: If a camera is not connected to a Camera IN terminal, that position will be skipped automatically. On a time lapse VCR, set the playback mode to the standard speed (e.g. 3H). In time lapse speed mode, playback may not be possible. 4 Divisions Split Screen Sequential Viewing From the split screen display, press the SEQUENCE button and 4 images at a time will be displayed in a 4 divisions split screen, switching sequentially. 16 English

18 CAMERA SCREEN DISPLAY CONTROL Monitor 1 ;; ;; Split screen (16 divisions) Camera Live Picture and VCR Playback Picture Simultaneous Viewing When viewing camera live pictures in a 16 or 13 divisions split screen, you can also view the VCR playback images. The VCR playback is viewed in the shaded area. 1 Sequential viewing of the VCR playback Start playback on the VCR, then press the PLUS1 button. The VCR playback images will be displayed sequentially according to the recorded speed. All the camera indicators will go off. ;;;; ;;;; Split screen (13 divisions) ;; 2 Selective viewing of the VCR playback (Example: Camera 5) Press a camera SELECT (5) button. The recording from that camera (5) will be played back according to the VCR recording speed. The title entered for the camera (see TITLE SETUP on page 9) will flash. Press the camera SELECT button (5) one more time to return to the previous display mode. ;; Menu NOTE: If a title has not been set for that camera, the camera number will flash. 3 VCR playback sequence set timing Press the SEQUENCE button and the display sequence timing will be as set in the DISPLAY SET menu (see page 11). ;; Menu To return to camera live picture viewing, press the PLUS1 button. English 17

19 CAMERA SCREEN DISPLAY CONTROL Monitor 2 Playback on Monitor 2 1 Press the SEQUENCE button The image on monitor 1 will be displayed full screen sequentially. The MULTI indicator will go off. 2 Press the PLUS1 button The PLUS1 indicator will flash, and the SEQUENCE indicator will go off. The image from camera 1 will be displayed automatically and the same image as viewed on monitor 1 will be viewed on monitor 2. Monitor 2 Monitor 1 NOTE: When there is no image displayed on monitor 2, while the PLUS1 indicator is flashing, press a camera SELECT button corresponding to a terminal where a camera has been connected. Monitor 2 Display Setup Press the camera SELECT button corresponding to the desired camera. The same image as viewed on monitor 1 will be viewed on monitor 2. This completes the setup. (1) Sequential Full Screen Display Press the SEQUENCE button to start sequential display on monitor 1 and monitor 2. The sequence timing is set in menu 4. DISPLAY SET, for more information, please refer to page 11. (2) To display on monitor 2 the same image as on monitor 1 In menu 4. DISPLAY SET, the item MONITOR2 MONITOR1 to Y (Yes). What is displayed on monitor 1 will also be displayed on monitor 2. While setting up the menus on monitor 1, you can confirm the sequence timing, the clock, the title, etc. on monitor 2. To return to camera live picture viewing, press the PLUS1 button. 18 English

20 ALARMS Alarm Display During Camera Live Picture Viewing When inputs such as a door bell, an interphone, etc., are connected to the CONTROL terminal, they will send alarm triggers automatically. On the monitor screen, A will flash instead of the camera number, and the camera indicator, and depending on the alarm setup (zoom or still), the corresponding button indicator will flash. While the camera indicator is flashing, press the SELECT button for full screen display of the camera live picture corresponding to the alarm trigger. When an alarm trigger is received, the following will take place. If in sequence display or full screen display, the display mode will automatically switch to split screen display. Even if the power to this unit is turned off, if the monitor is turned on, the power to this unit will be turned on automatically and the display will switch to split screen display. After the alarm operations, the unit will be turned off automatically if no button has been pressed (like pressing the SELECT button to switch from split screen to full screen display), during the alarm operations. NOTE: The alarm operations cannot be cancelled. Please wait until the alarm operation is finished. Setup Example The buzzer will ring for about 30 seconds, and the image of the corresponding camera will be zoomed in and freezed. The ZOOM, STILL and corresponding camera indicators will flash. After 30 seconds, everything will return to the mode previous to the alarm trigger. NOTE: When the items MONITOR1 ZOOM and STILL have been set to ON, the display mode will not switch to full screen display. For the operation when the RETRIGGER line is set to ON, please refer to Alarm Settings on page 10. Alarm Display During VCR Playback When playing back a camera recording, press the VCR button, then rewind the tape in the VCR and start playback. When reaching an alarm signal during playback, A will flash on the monitor instead of the camera number. NOTE: When reaching an alarm signal during playback, the display will automatically switch to 16 divisions split screen display. The corresponding camera indicator will light. English 19

21 VCR PLAYBACK SCREEN DISPLAY CONTROL While viewing live camera pictures, press the VCR button to view the VCR playback image. To return to camera live pictures, press the LIVE button. The VCR playback screen display control operations are almost the same as described under CAMERA SCREEN DISPLAY CONTROL. * If playing back a tape not recorded through this unit, the VCR indicator will flash and the message NO ID will be displayed on-screen. * If a camera picture is not recorded, the message NO VIDEO will be displayed on screen. * We recommend to use the 8-hour mode playback. Depending on the real time video recorder model, there may be a slight vertical shaking of the image or the top of the image may be slightly distorted during playback in 24- or 40-hour mode. (Monitor 2) b For split screen viewing (Monitor 1) b For zoomed in viewing b Freezed frame viewing NOTE: Audio playback of a time lapse recording in 12 or 24H mode will cause video interference. b For full screen viewing (x2 zoom) (Freeze frame) b For full screen sequential viewing b For 4 split screen sequential viewing b For simulaneous VCR playback and camera live viewing (Camera live picture) 20 English

22 VCR PLAYBACK SCREEN DISPLAY CONTROL Split Screen Viewing Monitor 1 By pressing the MULTI button, you can select one of the 8 split screen combinations. The camera indicators corresponding to the cameras displayed on-screen come on. NOTES: The unit will remember the selected screen display, and when turned on again it will automatically go back to the screen display combination selected before it was turned off. If a camera picture is not recorded, the message NO VIDEO will be displayed on screen. x2 Zoomed In Image Viewing Example: To watch the image from camera 14 at x2 zoom. 1 Press the ZOOM button, then press the camera SELECT (14) button. The image will be zoomed in, and Z will flash. (The ZOOM indicator and the camera (14) indicator will flash.) To cancel the zoom mode, press the ZOOM button one more time. The image can also be zoomed in when the screen is split in 4. 2 To switch to full screen display and to set the zoomed in image position. While in zoom mode ( Z displayed), press the camera SELECT (14) button for about 3 seconds. The zoomed image will be displayed full screen, and SET will be displayed. Using the following buttons adjust the zoomed in image position. Button O : To lower the image. Button «: To move the image towards the right. S NOTES: About 10 seconds after having set the image position, the display will automatically return to the original split display. The zoomed in image position is memorized and it will return to that position the next time the zoom function is used. 3 To freeze a zoomed in image. While in zoom mode ( Z displayed), press the STILL button, then press the camera SELECT (14) button. You can then view a zoomed in freezed image, and ZS will flash. To return to normal zoomed in mode, press the camera SELECT (14) button. To return to normal viewing mode, press the STILL button, then press the ZOOM button. Freezed Image Viewing Example: To freeze the image from camera 7. Press the STILL button, then press the camera SELECT (7) button. You can then view a freezed image, and S will flash instead of the camera number (7). To return to normal viewing mode, press the STILL button again. STILL 7 English 21

23 VCR PLAYBACK SCREEN DISPLAY CONTROL Full Screen Image Viewing Monitor 1 From the split screen display, press a camera SELECT button and the image from that camera will be displayed full screen. To return to split screen display, press the MULTI button. While viewing a full screen display, the following operations are available. 1 x2 Zoomed In Image Viewing Press the ZOOM button. The image will be zoomed in and Z will flash instead of the camera number. While in zoom mode ( Z displayed), press the STILL button. You can then view a zoomed in freezed image, and ZS will flash instead of the camera number. During zoom mode, the ZOOM indicator will flash. While the zoomed in image is freezed, the ZOOM indicator will light and the STILL indicator will flash. To return to normal zoomed in mode, press the STILL button. To return to normal viewing mode, press the ZOOM button. 2 Freezed Image Viewing Press the STILL button. You can then view a freezed image and S will flash instead of the camera number. While the image is freezed, the STILL indicator will flash. To return to normal viewing mode, press the STILL button again. Full Screen Sequential Viewing From the full screen display, press the SEQUENCE button to display the images full screen, switching sequentially. The SEQUENCE indicator will light, and the MULTI indicator will go off. To return to split screen display, press the MULTI button. NOTES: In a split screen display, the screens will be displayed sequentially, individually. When playing back using a timelapse VCR, use the standard speed (e.g. 3H). If using a different playback speed, playback may not be possible. 4 Divisions Split Screen Sequential Viewing From the split screen display, press the SEQUENCE button and 4 images at a time will be displayed in a 4 divisions split screen, switching sequentially. 22 English

24 VCR PLAYBACK SCREEN DISPLAY CONTROL Monitor 1 ;; ;; Split screen (16 divisions) VCR Recorded Picture and Camera Live Picture Simultaneous Viewing When viewing VCR playback in a 16 or 13 divisions split screen, you can also view the camera live pictures. The camera live pictures are viewed in the shaded area. 1 Sequential viewing of the camera live pictures Press the PLUS1 button, the camera live pictures will be displayed sequentially. The camera indicators will light according to the image displayed on-screen. ;;;; ;; ;;;; Split screen (13 divisions) 2 Selective viewing of the Camera live pictures (Example: Camera 5) Press the camera SELECT (5) button. The live pictures from camera (5) can be viewed. The title entered for the camera (see TITLE SETUP ) will flash. ;; Menu NOTE: If a title has not been set for that camera, the camera number will flash. 3 Camera live picture sequence set timing Press the SEQUENCE button and the display sequence timing will be as set in the DISPLAY SET menu. ;; Menu To return to VCR playback viewing, press the PLUS1 button. English 23

25 SPECIFICATIONS Video signal format : Based on PAL colour signal standard (MPX-CD16P) Based on PAL B/W signal standard (MPX-MD16P) Synchronisation : Asynchronous individual inputs (Internal synchronisation for MONITOR OUT 1 and camera OUT terminals) Camera input terminals : VS or VBS, 1.0Vp-p/75 Ω, BNC connector x 16 Camera output terminals : VS or VBS, 1.0Vp-p/75 Ω, BNC connector x 16 (Signal through) VCR input terminal VCR output terminal Normal mode Timelapse mode LP mode S-VIDEO input terminal S-VIDEO output terminal MONITOR1 output terminal MONITOR2 output terminal Alarm output terminal Switch input terminal Control terminal A/D Memory Skip Sequence timing On-screen display Buzzer Still Zoom Control signal Field switching Sync Character generator : VS or VBS, 1.0Vp-p/75 Ω, BNC connector x 1, S-VIDEO terminal (given the priority, MPX-CD16P only) x 1, auto-termination type : VS or VBS, 1.0Vp-p/75 Ω, BNC connector x 1, S-VIDEO terminal (MPX-CD16P only) : 1 field/channel switching output : 1 field/channel switching output, menu or switch signal standard : 1/2 field menu selectable : Separate Y/C signal, DIN terminal (MPX-CD16P only) : Separate Y/C signal, DIN terminal (MPX-CD16P only) : Video signal: VS or VBS, BNC connector x 1 (compatible with alarm display in full screen/split/sequential display modes) : Video signal: VS or VBS, BNC connector x 1 (Analog: compatibility with alarm display in full screen/sequential display modes setup by way of menu) : 16 channels (output 1 channel) : 100 kω pull-up : D-sub: alarm input, R/C (remote control) input Pin: Alarm output, switch input : 8 bits 256 gradation (excluding the sync signal), sampling rate: 4 x sub-carrier frequencies : Frame memory, Y signal (720 bit), C signal (360 bit) : Automatic (VCR OUT terminal, MONITOR 1, 2 output terminal) : sec (MONITOR 1, 2 output terminal) : Inputs, 8 character title, date/time, others (A Z, 0 9, symbols) : Internal (ON/OFF selectable for alarm warning) : Full screen/split screen (VCR playback, camera live), alarm operation : Full screen/split screen (VCR playback, camera live), alarm operation, x2 zoom : Camera number/title on 16 channels, date/time, alarm : SP/LP mode: setup by way of menu Timelapse mode: selectable according to setup, automatic according to switching pulse : SC and horizontal/vertical sync, with equivalence pulse : Size: 12 x 18 dots, selection: A Z, 0 9, symbols Brightness: 80% white with black frame Power : AC 220 ~ 240 V 50 Hz Consumption : Approx. 20 W Operating environment : Temperature: 0 to 45 C, Humidity: 10 to 70% Dimensions : 420 (W) x 44 (H) x 320 (D) mm Weight : Approx. 4 kg NOTE: The specifications and external appearance of this unit are subject to change without notice. 24 English

26 1AC6P1P L8FA5/XE, L8FB5/XE (A) (1196KP-SY01) SANYO Electric Co., Ltd. Printed in Japan