KC452xMx/KC652xMx USER MANUAL 1/3" BLACK-AND-WHITE CCD CAMERA

Transcription

1 KC452xMx/KC652xMx 1/3" BLACK-AND-WHITE CCD CAMERA USER MANUAL Ultrak Worldwide Support Center Sales & Technical Support 1301 Waters Ridge Drive Lewisville, TX (800) (972) FAX (972) KCMU000004

2 ISSUE 1 June BY ULTRAK ALL RIGHTS RESERVED ULTRAK CORPORATE OFFICE 1301 WATERS RIDGE DRIVE LEWISVILLE, TX (972) ALL RIGHTS RESERVED. NO PART OF THIS PUBLICATION MAY BE REPRODUCED BY ANY MEANS WITHOUT WRITTEN PERMISSION FROM ULTRAK. THE INFORMATION IN THIS PUBLICATION IS BELIEVED TO BE ACCURATE IN ALL RESPECTS. HOWEVER, ULTRAK CANNOT ASSUME RESPONSIBILITY FOR ANY CONSEQUENCES RESULTING FROM THE USE THEREOF. THE INFORMATION CONTAINED HEREIN IS SUBJECT TO CHANGE WITHOUT NOTICE. REVISIONS OR NEW EDITIONS TO THIS PUBLICATION MAY BE ISSUED TO INCORPORATE SUCH CHANGES. ii KCMU000004

3 FCC COMPLIANCE STATEMENT INFORMATION TO THE USER: THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS B DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC RULES. THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST HARMFUL INTERFERENCE IN A RESIDENTIAL INSTALLATION. THIS EQUIPMENT GENERATES, USES, AND CAN RADIATE RADIO FREQUENCY ENERGY AND, IF NOT INSTALLED AND USED IN ACCORDANCE WITH THE INSTRUCTIONS, MAY CAUSE HARMFUL INTERFERENCE TO RADIO COMMUNICATIONS. HOWEVER, THERE IS NO GUARANTEE THAT INTERFERENCE WILL NOT OCCUR IN A PARTICULAR INSTALLATION. IF THIS EQUIPMENT DOES CAUSE HARMFUL INTERFERENCE TO RADIO OR TELEVISION RECEPTION WHICH CAN BE DETERMINED BY TURNING THE EQUIPMENT OFF AND ON, THE USER IS ENCOURAGED TO TRY TO CORRECT THE INTERFERENCE BY ONE OR MORE OF THE FOLLOWING MEASURES: - REORIENT OR RELOCATE THE RECEIVING ANTENNA - INCREASE THE SEPARATION BETWEEN THE EQUIPMENT AND RECEIVER - CONNECT THE EQUIPMENT INTO AN OUTLET ON A CIRCUIT DIFFERENT FROM THAT TO WHICH THE RECEIVER IS CONNECTED - CONSULT THE DEALER OR AN EXPERIENCED RADIO/TV TECHNICIAN FOR HELP CAUTION: CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER S AUTHORITY TO OPERATE THE EQUIPMENT. THIS CLASS B DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES CET APPAREIL NUMÉRIQUE DE LA CLASSE B EST CONFORME A LA NORME NMB-003 DU CANADA. USERS OF THE PRODUCT ARE RESPONSIBLE FOR CHECKING AND COMPLYING WITH ALL FEDERAL STATE AND LOCAL LAWS AND STATUTES CONCERNING THE MONITORING AND RECORDING OF VIDEO AND AUDIO SIGNALS. ULTRAK SHALL NOT BE HELD RESPONSIBLE FOR THE USE OF THIS PRODUCT IN VIOLATION OF CURRENT LAWS AND STATUTES. iii KCMU000004

4 WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC OBJECT THROUGH VENTILA- TION GRILLS. CAUTION CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. EXPLANATION OF GRAPHICAL SYMBOLS The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instruction in the literature accompanying the product. iv KCMU000004

5 IMPORTANT SAFEGUARDS 1. READ INSTRUCTIONS All of the safety and operating instructions should be read before the appliance is operated. 2. RETAIN INSTRUCTIONS The safety and operating instructions should be retained for future reference. 3. HEED WARNINGS All warnings on the product and in the operating instructions should be adhered to. 4. FOLLOW INSTRUCTIONS All operating and use instructions should be followed. 5. CLEANING Unplug this appliance from wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 6. ATTACHMENTS Do not use attachments not recommended by the appliance manufacturer as they may cause hazards. 7. WATER AND MOISTURE Do not use this product near water or moisture. (For example, near a bathtub, sink, laundry tub, in a wet basement, near a swimming pool, etc.) Unless otherwise specified, cameras may be used in outdoor settings only when used with approved camera housing. 8. INSTALLATION Do not place this product on an unstable cart, stand, or table. The product may fall, causing serious injury to a child or adult, and damage to the product. Use only with a cart or stand recommended by the manufacturer or sold with the product. Follow the manufacturer s instructions for mounting and use a mounting accessory recommended by the manufacturer. Test cameras and cables prior to mounting and running cables. 9. MOVING Product and cart combinations should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn. 10. VENTILATION Slots and openings in the cabinet and the back or bottom are provided for ventilation, to insure reliable operation of the product, and to protect it from overheating. These openings must not be blocked or covered. The openings should never be blocked by placing the unit on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation, such as a bookcase, unless proper ventilation is provided. Continued on next page. v KCMU000004

6 IMPORTANT SAFEGUARDS, continued 11. POWER SOURCE This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supplied to your home, consult your dealer or local power company. 12. GROUNDING OR POLARIZATION This camera may be equipped with a polarized alternation current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug. 13. OVERLOADING Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock. 14. REPLACEMENT PARTS When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards. 15. SAFETY CHECK Upon completion of any service or repairs to this camera, ask the service technician to perform safety checks to determine that the camera is in proper operating condition. 16. FIELD INSTALLATION This installation should be made by a qualified person and should conform to all local codes. vi KCMU000004

7 PRECAUTIONS OPERATING Before operating, make sure that the power supply and video output are connected correctly. While operating, if any abnormal condition or malfunction is observed, stop using the camera immediately and call your local dealer. HANDLING Do not disassemble the camera and never touch parts inside the camera. Do not drop the camera or subject it to shocks and vibrations to avoid possible damage. When attaching or removing the lens, handle with care so that moisture and dust do not enter the camera. Do not shoot any source of bright light. If the object contains very bright areas, bright vertical or horizontal lines may appear on the screen. This is called smear and is a phenomenon, which often occurs with solid-state pickups. It is not a malfunction. INSTALLING AND STORING Do not point the camera at the sun. This could damage the camera whether it is operating or not. Do not install the camera in extreme temperature conditions. Be sure that the ambient temperature is less than 104 F (40 C) for long-term continuous operation. Avoid installing in humid or dusty places. Avoid installing in places where there is radiation. This could damage CCD and other components and cause malfunction. Avoid installing in places where there are strong magnetic fields and electrical signals. Avoid installing in places where the camera would be subject to strong vibrations. Never expose the camera to rain and water. CLEANING Turn the power off and wipe off the dirt with dry soft cloths. If it is extremely dirty, use furniture-cleaning tissue. Do not use alcohols, petroleum distillates, liquid cleaners, or sprays. PERFORMING DAILY CHECKS Make daily checks for proper operation for surveillance use. In order to maintain normal operation, the output of the camera should be checked by user every day for a clear and focused picture. vii KCMU000004

8 THIS PAGE INTENTIONALLY LEFT BLANK. viii KCMU000004

9 TABLE OF CONTENTS SECTION 1: INTRODUCTION...1 PRODUCT DESCRIPTION...1 FEATURES...1 SECTION 2 CONTROLS AND CONNECTIONS...3 CAMERA TOP...3 CAMERA BOTTOM...4 CAMERA FRONT...5 CAMERA BACK...6 SECTION 3: INSTALLATION AND ADJUSTMENT...9 CONTENTS OF PACKAGE...9 BASIC INSTALLATION...9 INSTALLING C-MOUNT OR CS-MOUNT LENS...10 INSTALLING AUTO IRIS LENS...11 INSTALLING VIDEO-TYPE AUTO IRIS LENS...11 ADJUSTING ALC...12 ADJUSTING LEVEL...12 ADJUSTING AGC...13 INSTALLING DC-TYPE AUTO-IRIS LENS...13 ROUTING THE CABLE...14 CONNECTING THE CABLE...14 INSTRUCTIONS FOR KCX520MX MODELS (24V AC)...14 INSTRUCTIONS FOR KCX521MP MODELS (230V AC)...15 SECTION 3: TROUBLESHOOTING AND PREVENTIVE MAINTENANCE...19 TROUBLESHOOTING...19 PREVENTIVE MAINTENANCE...20 SPECIFICATIONS...21 ix KCMU000004

10 THIS PAGE INTENTIONALLY LEFT BLANK. x KCMU000004

11 SECTION 1: INTRODUCTION PRODUCT DESCRIPTION FEATURES The KC452xMx/KC652xMx black-and-white security cameras provide high-quality images using CCD technology especially designed for closed-circuit television (CCTV) and security surveillance applications. The cameras include the following features: High sensitivity. 1/3" CCD with a professionallevel camera chip that achieves a very high quality picture and provides high sensitivity down to 0.04 lux (F1.2) for the KC452xMx and 0.08 lux (F1.2) for the KC652xMx. High quality image. High resolution, high sensitivity design for a horizontal resolution of 420 TV lines for the KC452xMx and 570 TV lines for the KC652xMx. Backlight compensation. When strong light enters the scene background, such as from a spotlight or window, the backlight compensation function automatically adjusts the video level to preserve visibility in important sections of the image. Iris Function. Iris function provides a drive output for video-type and DC-type lenses. A builtin electronic shutter also allows shutter speeds in the range of 1/60 to 1/100,000 for the KCx520MN and 1/50 to 1/100,000 for the KCx52xMP. CCD iris function automatically sets the brightness of the picture by changing the shutter speed of the camera according to the incident light when using a manual iris lens. 1 KCMU000004

12 THIS PAGE INTENTIONALLY LEFT BLANK. 2 KCMU000004

13 SECTION 2 CONTROLS AND CONNECTIONS CAMERA TOP 1. Auto-iris Lens Connector This 4-pin female connector allows the user to connect an auto-iris lens. The connector supplies the power and a video signal or DC control signal to the auto-iris lens. (A 4-pin male connector is supplied.) 2. Camera Mounting Bracket This threaded 1/4-20 hole is used to mount the camera onto a mounting bracket or tripod. 3 KCMU000004

14 CAMERA BOTTOM 3. Camera Mounting Bracket This threaded 1/4-20 hole is used to mount the camera onto a mounting bracket or tripod. 4 KCMU000004

15 CAMERA FRONT 4. Back-focus Lock Screw A screw that allows the user to secure the back-focus setting. 5. Back-focus Adjust Ring A ring that allows the user to adjust the back-focal length or picture focus of the lens by rotating it clockwise for CSmount lenses or counterclockwise for C-mount lenses. 5 KCMU000004

16 CAMERA BACK 6. Level This control adjusts the level of the DC-type auto-iris lens. 7. Phase Phase adjustment is used in multicamera systems when power is supplied from different sources, thus causing the camera to be out of phase. This, in turn, affects auto-switching by causing rolling of the video during the switch interval. The vertical phase adjustment allows the camera s line lock sync to be adjusted from 0 to 360 degrees with zero line crossing the AC power source. To effectively use the phase adjustment, ensure that all cameras are powered from the same electrical source and that they are wired in a similar fashion. Then, adjust the phase control on the top of the camera until there is no rolling video on the monitor when using the auto-switcher. Continued on next page. 6 KCMU000004

17 CAMERA BACK, continued 8-1 Power Input Terminal This terminal accepts a 24V ac power source from a 24V ac +/- 10% 50Hz +/- 1% (CCIR)/60Hz +/-1%(EIA) power source AC Power Cord This power cord accepts a 230V ac +/- 10% 50Hz +/- 1% power source. 9. Power LED This green LED illuminates while power is supplied to the camera. 10. Function Switches A switch is in the ON position if it is positioned upward. If the position is set downward, the switch is OFF. The switches include: AGC Switch The auto gain control switch allows the video signals to maintain a constant level. This switch is useful when using the camera at low-light levels and when lighting levels change over time. A/I Switch The auto iris switch allows the user to select the supplied auto-iris control signal for the lens. Position the switch upward to choose DC when the auto-iris control lens requires DC control signal. Position the switch downward to choose VIDEO when the auto-iris control lens requires video signal. E/I When set to ON position, the electronic iris switch automatically varies the camera s shutter to mimic auto-iris control, allowing fixed or manual iris lenses to be used in a wider range. Continued on next page. 7 KCMU000004

18 CAMERA BACK, continued 11. Video Out Connector This BNC connector outputs a 1.0 Vp-p/75 ohms composite video signal. 8 KCMU000004

19 SECTION 3: INSTALLATION AND ADJUSTMENT CONTENTS OF PACKAGE BASIC INSTALLATION Carefully remove the camera and its accessories from the carton and verify that they were not damaged in shipment. The contents of the package include: 1. Black-and-white CCD camera 2. Connector (for video or DC type auto-iris lens) 3. User Manual After unpacking and identifying the package contents, perform the following steps to connect the camera to an observation system. 1. Locate the following items, which may be needed during installation yet are NOT supplied with the KC452xMx/KC652xMx cameras: Camera lens Video cable Camera stand or mounting bracket 24V ac power supply with UL-listed Class 2 power transformer and Class 2 power source Mounting hardware Observation monitor Welder s glass Tools Continued on next page. 9 KCMU000004

20 BASIC INSTALLATION, continued 2. Test camera and cables prior to mounting and running cables. IMPORTANT: Contact your authorized Ultrak dealer/distributor to purchase longer cables. 3. Select a suitable location for the camera IMPORTANT: Unless otherwise specified, cameras may be used in outdoor settings only when used with approved camera housing. 4. Use a suitable fastener and necessary tools to mount the camera stand to a structural object that can support the weight of the camera and the mount, such as a wall stud, shelf, ceiling rafter, etc. The maximum recommended load rating for the bracket is 11 pounds. 5. The KC452xMx/KC652xMx observation cameras have a 1/4-20 UNC mounting hole located at the top and bottom of the camera housing to allow for bottom or top mounting. Mount the camera onto the threaded mounting bolt. IMPORTANT: Do not aim or point the camera towards the sun or into a strong light. Installing C-Mount or CS-Mount Lens Install the lens. If a C- or CS-mount lens is used, adjust the back-focal length or picture focus. For C- mount lenses, rotate the focus-adjust ring counterclockwise. For CS-mount lenses, rotate the focus-adjust ring clockwise. 10 KCMU000004

21 BASIC INSTALLATION, continued Installing Auto Iris Lens If an auto-iris lens is used, connect the cable to the connector supplied with the camera. Insert the lens connector into the auto-iris connector on the camera. Installing Video-Type Auto Iris Lens The KC452xMx/KC652xMx cameras support videotype auto-iris lenses to adjust for changing light levels. Perform the following steps to install and adjust a video-type auto-iris lens. 1. Thread the video-type auto-iris lens onto the lens mount on the front of the camera. 2. If necessary, solder the lens control wires to the connector supplied with the camera. Use the following pin-out and wire color-coding chart as a guide. PIN NAME WIRE COLOR 1 Voltage + Red 2 Open -- 3 Video White 4 Ground Black Open Voltage + / Red Video / White Ground / Black Continued on next page. 11 KCMU000004

22 BASIC INSTALLATION, continued Installing Video-Type Auto Iris Lens, continued 3. Plug the connector into the auto-iris lens jack on the front of the camera. The connector is keyed and can only be inserted into the jack one way. 4. Make sure that the E/I switch located on the back of the camera is set to OFF. 5. Apply power to the camera. 6. Adjust the focus ring on the lens for an optimum picture. If the picture is not visible, set the lens for proper exposure by adjusting the ALC (automatic level control) and LEVEL on the lens. The ALC setting can range between AVG (average) or PK (peak). An AVG setting is appropriate for most applications. Adjusting ALC AVG To slow the reaction of the lens to changing light, set the range on the AVG setting to average the video level from the camera. Use this when there are bright spots in the picture, such as lights or glare from the sun. PK To increase the speed of the lens reaction to the changing light, set the lens adjustment to PK so the lens will adjust to the brightest or peak object in the video. Use this setting if you want to see the brightest object and not the background objects. Adjusting Level Adjust the Level control for the best picture during the day. A night adjustment may not provide the proper setting for controlling the light during the day. 1. Set the back-focus of the camera before the final adjustment of the video level. (See the section on Back-focus Adjustment later in this manual.) 12 KCMU000004

23 BASIC INSTALLATION, continued Adjusting AGC 1. If the auto-iris has a gain adjustment, perform the following steps: a. If the lens oscillates between open and closed under bright lights, slowly turn the gain adjustment counterclockwise until the oscillating stops. b. Increase the light getting to the camera by adjusting the level control and readjusting the gain control as necessary. c. Reset the level control as illustrated in Step 6. Installing DC-Type Auto-Iris Lens The KC452xMx/KC652xMx cameras support DC autoiris lenses. Perform the following steps to install and adjust a DC-type auto-iris lens. 1. Thread the DC iris lens onto the lens mount on the front of the camera. 2. If using an Ultrak lens, skip to step If using a non-ultrak lens, use the manufacturer s instructions to solder the connector that comes supplied with the camera to the lens control wires. The pin-out and wire color-coding for DC-type auto-iris lenses can vary from one manufacturer to another. 4. Plug the connector into the DC iris jack on the front of the camera. The connector is keyed and can only be inserted into the jack one way. 5. Make sure that the E/I switch located on the back of the camera is set to OFF. 6. Apply power to the camera. 7. Adjust the DC-type auto-iris lens for an optimum picture using the IRIS LEVEL control on the back of the camera. 13 KCMU000004

24 BASIC INSTALLATION, continued Routing the Cable Route the video cable from the monitor location to the camera location. WARNING: Care should be taken when routing the cable from the monitor to the camera. Try not to put unnecessary strain on the cable or connectors. Do not place the cable next to fluorescent lights as interference may result. Do not use staples to support the cable as they may damage the cable. If the provided camera cable is not long enough, do not substitute a telephone cable as it could damage the camera and/or the monitor. Contact your authorized Ultrak dealer/distributor to purchase longer cables. Connecting the Cable 1. Plug the cable into the BNC output connector port labeled VIDEO OUT located on the back of the camera. 2. Plug the other end of the cable into the corresponding video input port on the back of the observation monitor. Instructions for KCx520Mx Models (24V ac) 1. Connect a two-conductor power cable to the 24V ac input port located on the back of the camera. 2. Apply 24V ac power to the camera. 24V ac Class 2 Use a UL-listed Class 2 power transformer and a 24V power adapter. Use only a Class 2 power source. ~ G ~ 14 KCMU000004

25 BASIC INSTALLATION, continued Instructions for KCx521MP Models (230V ac) 1. Plug the power cord into a wall outlet. 2. Apply 230V ac power to the camera. 3. Plug the monitor s power cable into a suitable wall outlet. 4. Turn on the monitor s power switch(es). The monitor should display images for the connected camera(s). For more information on system installation and camera display options, refer to the observation monitor or system manual. 5. Adjust the camera back-focus, lens focus, and iris controls for an optimum picture. Back-focus Adjustment Although the camera lens was back-focused by the manufacturer prior to shipping, it may be necessary to make modifications. For best results, perform back-focus adjustments at night or while using a #6 or #8 welder s glass in front of the lens. The focus of the camera could change slightly if the camera iris is adjusted when focused on a light scene, which then changes to a dark scene. However, the camera will remain in focus if the camera iris is adjusted when focused on a dark scene, which then changes to a lighter scene. To make back-focus adjustments, perform the following steps: 1. After mounting the lens on the camera, apply power. 2. Open the camera iris by turning the lens level control counterclockwise. Continued on next page. 15 KCMU000004

26 BASIC INSTALLATION, continued Back-Focus Adjustment, continued 3. If a picture is visible, focus on the scene. Open the lens as wide as possible by placing a welder s glass in front of the lens. 4. When the iris is open to the widest point, readjust the focus for a clear picture. If a clear picture is not visible, set the focus ring to midrange. 5. Loosen the back-focus lock screw. Back-focus Screw Back-focus Adjust Ring 6. Adjust the back-focus ring for a clear picture. 7. Tighten the back-focus lock screw. 8. Fine-tune the focus with the focus ring on the lens. 9. Remove the welder s glass from the front of the lens. 10. Adjust the level control of the lens for the best picture quality. 16 KCMU000004

27 BASIC INSTALLATION, continued Adjusting Back-focus on Zoom Lens The objective of back-focusing a zoom lens is similar to that of a fixed-focal length camera, except that the back-focus is also adjusted to maintain the focus when zooming the lens in and out of a scene. For zoom lens back-focus adjustment, perform the following steps: 1. Choose an object at the farthest range that you wish to look at with a zoom lens. 2. Make sure that the iris of the lens is wide open. For best results, make the adjustment by using a welder s glass placed in front of the lens. 3. Adjust the focus to stop on the far range. 4. Adjust the zoom on the lens to obtain the widest picture. 5. Loosen the back-focus lock screw. 6. Adjust the back-focus ring for the clearest picture. 7. Adjust the zoom on the lens to the far telephoto position. 8. Adjust the back-focus ring for the clearest picture. 9. Adjust the zoom on the lens back to the widest picture. 10. Readjust the back-focus for the clearest picture. 11. Tighten the back-focus lock screw. 12. Repeat the previous steps as many times as necessary to maintain a clear picture through the entire zoom range. IMPORTANT: Verify that the camera remains in focus after tightening the lock screw. On occasion, tightening the lock screw can cause the camera to be slightly out of focus. 17 KCMU000004

28 THIS PAGE INTENTIONALLY LEFT BLANK. 18 KCMU000004

29 SECTION 3: TROUBLESHOOTING AND PREVENTIVE MAINTENANCE TROUBLESHOOTING If problems occur, verify the installation of the camera with the instructions in this manual and with other operating equipment. Isolate the problem to the specific piece of equipment in the system and refer to the equipment manual for further information. PROBLEM There is no power. There is power but no picture. The video is too dark. There is video, but no control. CHECK Make sure the system is plugged in. Check the outlet for power. Make sure the power switch on the front of the monitor is ON. Check video and DC drive switch position. Make sure there is nothing blocking the lens of the camera. Make sure the camera cable is plugged into the monitor and the camera. Adjust the iris and check A/I connections. Power down the system for one minute, and then turn the power back ON. 19 KCMU000004

30 PREVENTIVE MAINTENANCE Following the preventive maintenance schedule allows detection and correction of minor faults before they become serious and cause equipment failure. Every three months, perform the following: 1. Inspect all connecting cables for deterioration or other damage. 2. Clean components with a clean, damp cloth. 3. Verify that all the mounting hardware is secure. 20 KCMU000004

31 SPECIFICATIONS Power Source: Power Consumption: Image Sensor: Scanning Frequency: Minimum Illumination: Resolution: Video Output: Lens Mount: Signal/Noise Ratio: Camera Mount: 24V ac for KCx520Mx models 230V ac for KCx521MP models 4.5W maximum for KCx520Mx models 5.0W maximum for KCx521MP models 1/3 black-and-white CCD Horizontal 15.75KHz for KCx520MN Horizontal KHz for KCx52xMP Vertical 60Hz for KCx520MN Vertical 50Hz for KCx52xMP 0.4 Lux for KC452xMx 0.8 Lux for KC652xMx KC452xMx: 380 TV/420 apparent lines KC652xMx: 570 TV lines 1 Vp-p, 75 Ω C/CS-Mount (adjustable back-focus ring) 46dB (AGC off) 1/4 20 UNC (top/bottom) Camera Connectors: Video Out: Power Input: KCx520Mx: KCx521MP: Auto-iris Output: BNC connector 3-pin terminal block AC power cord 4-pin Ambient Temperature: 14 F to 122 F (-10 C to 50 C) Continued on next page. 21 KCMU000004

32 SPECIFICATIONS, continued Ambient Humidity Dimensions: Weight: 0~96% (non-condensing) 2.4W x 2.1H x 5.5D in (62W x 54H x 140D mm) KCx520Mx 12.2oz (345g) KCx521MP 18.5oz (525g) NOTE: If used continuously, be sure to operate at temperatures less than 40 C (104 F) for long-term stable performance. 22 KCMU000004