VCC-HD1X. Product Specification & Operational Manual. 3G-SDI/HD-SDI FULL HD Color CMOS Camera Module. CIS Corporation. English

Transcription

1 VCC-HD1X Rev English 3G-SDI/HD-SDI FULL HD Color CMOS Camera Module VCC-HD1X Product Specification & Operational Manual CIS Corporation

2 Table of Contents PAGE 1. Handling Precautions Product Outline Bundled Items Standard Bundled Items Packaging Optional Items Specifications General Specifications Parts Name and Functions External Connector Specifications pins Circular Connector BNC DC IRIS Connector φ3.5mm 4 poles (RS-232C) Connector GenLock LTC (Longitudinal Time code) Notes for CMOS Pixel Defect Correction Precautions How to run Defective Pixel Correction Serial Communication Serial communication setting Command Command List Table for Setting Value Camera Operation with OSD Switching operation of the OSD menu display by remote controller OSD Menu Indication OSD Menu List Factory Settings Dimensions Case for Indemnity (Limited Warranty) CMOS Pixel Defect Product Support

3 1. Handling Precautions The camera module must not be used for any nuclear equipments or aerospace equipments with which mechanical failure or malfunction could result in serious bodily injury or loss of human life. Our warranty does not apply to damages or defects caused by irregular and/or abnormal use of the product. All specifications contained herein are subject to change without prior notice. Reproduction in whole or in part is prohibited. Please observe all warnings and cautions stated below. Our warranty does not apply to damages or malfunctions caused by neglecting these precautions. Do not use or store the camera module in the dusty or humid places. Do not apply excessive force or static electricity that could damage the camera module. Do not shoot direct images that are extremely bright (e.g., light source, sun, etc). When the camera is not in use, please put the protection cap on. Follow the instructions in Chapter 6, External Connector Pin Assignment for connecting the camera module. Improper connection may cause damages not only to the camera module but also to the connected devices. Confirm the mutual ground potential carefully and then connect the camera module to monitors or computers. AC leaks from the connected devices may cause damages or destroy the camera module. Do not apply excessive voltage. (Use only the specified voltage.) Unstable or improper power supply voltage may cause damages or malfunction of the camera assembly. Since VCC-HD1X is a highly-dense camera module, appropriate heat dissipation shall be considered. We recommend using a metal base or others to install the camera. Operating this camera assembly without appropriate heat dissipation considered may cause damages or malfunction. 2. Product Outline VCC-HD1X is a full HD color camera with Gen Lock function utilizing a 1/3 type CMOS image sensor p/59.94p/50p (3G-SDI), i/59.94i/50 i/30p/29.97p/25p /24p/23.97p (HD-SDI), p/59.94p/50p (HD-SDI) are available. Features Features CIS original ISP, state-of-the-art Clairvu TM for superb imaging quality. Small foot print: 29mm 29mm 77mm (without projection). GenLock (3-value analog signals or Black burst ) Camera can be controlled by RS-232C. LTC (Longitudinal Time code) Connecting an optional remote controller, camera settings can be set on OSD (On Screen Display). 2

4 3. Bundled Items 3.1. Standard Bundled Items Camera module, VCC-HD1X C/CS lens mount conversion ring (Attached to the camera) Lens Mount Cap (Attached to the camera) 6 pins connector for power 3.2. Packaging Individual carton Master Carton (10pcs per carton) *Number of cameras in a master carton varies depends on the shipping quantities Optional Items RS-232C conversion cable (φ3.5mm plug <->9pin D-sub: under planning) Remote controller (under planning) 3

5 4. Specifications 4.1. General Specifications (1) Image Sensor Device Type 1/3 type CMOS sensor (color) Effective Pixel Numbers Unit Cell Size Chip Size 1944(H) 1213(V) 2.75μm(H) 2.75μm(V) (2) Resolution 1080p,1080i : 1920(H) 1080(V) (3) Aspect Ratio 16 : 9 720p : 5.346mm(H) 3.336mm(V) (Effective Pixels areas) 1280(H) 720(V) (4) Video Output Format 1920 x A) 3G-SDI (5) Sync. System Internal /External sync. system 1920 x B) 3G-SDI 1920 x A) 3G-SDI 1920 x B) 3G-SDI 1920 x A) 3G-SDI 1920 x B) 3G-SDI 1920 x HD-SDI 1920 x HD-SDI 1920 x HD-SDI 1920 x HD-SDI 1920 x HD-SDI 1920 x HD-SDI 1920 x HD-SDI 1920 x HD-SDI 1280 x HD-SDI 1280 x HD-SDI 1280 x HD-SDI (6) Video Output Standard 3G-SDI/HD-SDI : Y/Pb/Pr (4:2:2 10bit) BNC 75Ω termination (7) Sensitivity F lx (8) Minimum illumination F lx (9) Dust or stains in optical systems (10) Power Requirements(*1) DC+9~+15V (11) Power Consumption(*1) 4.0 W at DC+12V IN Conditions : VIDEO 50%, AGC 30dB, Electric Shutter OFF No dust or stain shall be detected on the testing screen with setting the camera aperture at F16. (12) Dimensions Refer to overall dimension drawing. (13) Weight Approx. 92g (14) Lens Mount C/CS mount (C/CS can be switched by mounting/dismounting conversion ring) *Refer to overall dimension drawing (15) Gain Setting AGC (Max. Gain : 0dB~30dB) MANUAL: 0dB~30dB (by 1dB) 4

6 (16) Shutter Speed Variable MANUAL: 1/8000s 1/4000s 1/2000s 1/1000s 1/500s 1/250s 1/125s.. Range 1/100s..1/60s,1/50s..1/30s,1/25s *Shutter speed slower than 1/60s will be limited by the frame rate corresponding to the video output format. And, the shutter is limited to 1/25s at 24fps. AUTO: 1/8000s~1/60s or 1/50s or 1/30s or 1/25s (Upper limit and lower limit can be set.) *Same as MANUAL, shutter speed slower than 1/60s will be limited by the frame rate corresponding to the video output format. And, the shutter is limited to 1/25s at 24fps. (17) White Balance Adjustment Range AUTO, AUTO (Outdoor), ATW, 7 different Preset, MANUAL, User Preset 1~5, One Push Preset: Daylight (5500K), Cloudy (6500K), Shade (8000K), Tungsten (3200K), Fluorescent (White), Fluorescent (Neutral White), Fluorescent (Daylight) 6500K (18) DC IRIS output Auto/Open Selectable. Can be used with electric shutter (With priority to electric shutter). (19) Auto Exposure Detection Average/Center-Weight/Spot(1/256)/Backlight Compensation (20) Flicker cancellation ON, OFF (typ.) (21) Edge Enhancement OFF, 1~7 (typ. 3) (22) Color Correction Standard, Fluorescent Light, Tungsten Lamp (23) Color Saturation Adjustment 0% (B/W)~100% (typ.)~200% (24) Color Saturation Suppression OFF, 1~7 (typ. 5) (25) Noise Reduction ON, OFF (26) Gamma Correction Contrast-2, Contrast-1, Standard, Contrast+1, Contrast+2 (27) Master Pedestal -100 ~ 0 ~ +100 (28) Pedestal (R, G, B) RGB: -100 ~ 0 (typ.) ~ +100 each (29) Color Balance RGB: 50 ~ 100 (typ.) ~ 150 each (30) Pixel Defect (White spot) Correction Corrected at factory setting. (31) LTC OFF, ON. The external SMPTE Time code can be input to LTC IN terminal (internal self-counted time code is possible to reset). (32) Preset (Camera settings) 1, 2, 3, 4 (4 presets are possible) (33) Remote Control Operation The camera can be controlled via RS-232C communications with φ3.5 plug (4poles). Camera settings can be controlled by control software via PC. Camera settings are possible on OSD (On Screen Display) by connecting the remote controller to this connector. (34) Safety/Quality standards UL: Conform to UL Standard including materials and others. RoHS: Conform to RoHS CE: EN55022: 2010 (Class B) for Emission. EN : 2005 for Immunity. FCC: To be applied for Class A Digital Device This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. (35) Durability Vibration Acceleration 98m/s 2 (10G) Shock Frequency Direction 20~200 Hz X,Y, and Z, 3 directions Testing time 120min for each direction No malfunction shall be occurred with 980m/s 2 (100G) for ±X,±Y, and ±Z, 6 directions. 5

7 (36) Operation environment Performance guaranteed Operation guaranteed 0 ~ +40 Humidity 20 ~ 80%RH -5 ~ +45 Humidity 20 ~ 80%RH with no condensation with no condensation Performance guaranteed: All the specifications specified in this manual is guaranteed under performance guaranteed temperature. Operation guaranteed: All the camera functions operate normally under operation guaranteed temperature. (37) Storage Environment Storage Temperature: -25 ~ +60, Humidity: 20 ~ 80%RH with no condensation. <3G-SDI output Level A and Level B> A difference between Level A and Level B is a way of mapping Y signal and Cb/Cr signal onto 3G-SDI standard signal. The difference does not affect the resolution of the video signal. Some 3G-SDI receivers correspond to either Level A or B, whereas other receivers correspond to both Levels, so please set the camera mode to match your 3G-SDI receiver. 6

8 5. Parts Name and Functions 1 C/CS Mount To mount a C/CS mount lens. C/CS conversion ring need to be mounted when using the C mount lens (factory setting). The C/CS conversion ring need to be removed when using CS mount lens. Screw length from the lens mount surface shall be less than 6mm. And protruding portion of the lens shall be less than 8mm. When lens is not mounted, please put the attached lens mount cap on. 2 DC IRIS Connector To connect a DC IRIS lens. 3 Connector for Power input,genlock and LTC input Please refer to the external connector pin assignment. 4 Video Signal Output With BNC cable, connect to a 3G-SDI input monitor or HD-SDI input monitor. (Analog monitors cannot be connected.) BNC cables with high frequency characteristic corresponding to 3G-SDI or HD-SDI shall be used. 5 φ3.5 (4 pole) Connector (RS-232C) Connector for RS-232C. Please refer to the external connector pin assignment. Please refer to the other materials for the details of serial communications. * Do not connect to any audio equipment such as earphones and headset. Connecting to such equipment may cause malfunction. 6 Screw Holes for camera installation 4 screw holes to attach the camera. Please note that the depth of the front screw holes and the rear screw holes are different. 7

9 6. External Connector Specifications pins Circular Connector Model Name HR10-7R-6PA (HIROSE) Pin No. Description Power IN DC+12V 2 EXT SYNC IN 3 LTC IN 4 N.C. 5 GND 6 GND 6.2. BNC Model Name BCJ-BPLHA (CANARE) 1 Pin No. Description 2 1 3G-SDI/HD-SDI output 2 GND 6.3. DC IRIS Connector Model Name D4-156N-200A (TECHNICAL ELCTRON CO., LTD) Pin No. Description 1 DAMP- 2 DAMP+ 3 DRIVE+ 4 DRIVE-(GND) 6.4. φ3.5mm 4 poles (RS-232C) Connector Model Name: MJ Pin No. Description 1 Power(+5V) * for option 2 TXD(Camera) 3 RXD(Camera) 4 GND Connection of φ3.5 (4 pole) Connector (RS-232C) N.C RXD TXD GND N.C RXD TXD GND pin D-Sub(female) PC 3 4 8

10 7. GenLock Gen Lock function is available by inputting Analog External Sync signal (Black burst or 3-value SYNC) in to the EXT SYNC IN terminal of 6pins connector. Corresponding external sync signals vary depends on the camera output format. Please refer to the chart below for the details. CAMERA FORMAT EXT SYNC IN 1080p60A 1080i60 720p p p59.9A NTSC 1080i p p p50A PAL 1080i50 720p p p60B 1080i60 720p p p59.9B NTSC 1080i p p p50B PAL 1080i50 720p p i i60 720p p i59.94 NTSC 1080i p p i50 PAL 1080i50 720p p p i60 720p p p29.9 NTSC 1080i p p p25 PAL 1080i50 720p p p p p p p i60 720p p30 720p59.9 NTSC 1080i p p p50 PAL 1080i50 720p p25 Input Black Burst signal for NTSC/PAL signal. Input 3-value SYNC signals for other than NTSC/PAL signals. EXT SYNC IN is terminated with 75Ω. (When camera power is OFF, it will be high-impedance.). When the external signal specified the above is input, the camera will be in external sync mode automatically. When no external signal is input, the camera will operate in internal sync mode. Right after external signals are input, images may be disturbed but this is not malfunction. When a signal other than the specified above chart is input to the EXT SYNC IN terminal, disturbed image or no image may be shown. 8. LTC (Longitudinal Time code) Time code can be inserted to 3G/HD SDI signal. External time code can be inserted with inputting LTC code to the LTC IN terminal of the 6pins connector. And, when no signal is input into the LTC IN terminal, internal time code can be inserted. Internal time code starts with 00:00: when power is ON, and when any signals are input into the LTC IN terminal, it will be changed to external time code. With this situation, if no signal is input to the LTC IN terminal, it becomes self-running from the set time code. Signal Format: SMPTE Time code Signal Level: 0.5 ~ 2[Vp-p] 9

11 9. Notes for CMOS Pixel Defect Correction 9.1. Precautions If you execute pixel defect correction and SAVE, the correction data set at the factory setting will be overwritten and the data cannot be returned to the factory setting even if you execute INIT command. If you SAVE after executing INIT, the selected preset value (Camera Setting) will be overwritten by the factory setting value. If you do not wish the pre-set value overwritten, load the pre-set value before SAVE. All the defective pixel correction data will be saved in one area regardless of their preset numbers. Pixel defect correction is only for White pixel defect but not for black pixel defect. This function is not necessarily able to correct all the white defects. Also please be noted that the corrected results may not be the same depending on temperature, noise, and other conditions. Please be sure to execute the command with blocking out lights and follow the proper procedures. Neglecting this instruction may cause not only inappropriate pixel defect correction but also failure of getting proper images How to run Defective Pixel Correction Execute INIT to get it back to the factory settings. Attach the bundled cap to the lens mount and wait for about 5 seconds after completing light-shielding. Run Defective Pixel Correction, and execute SAVE. 10. Serial Communication Serial communication setting Transmit Speed: 9600bps Data Length: 8 bit Start bit: 1 bit Parity bit: NO Stop bit: 1 bit Command Command Parameter 1 Parameter 2 Function GU (Get User) Command number Normally None Obtaining of various data of the camera SU (Set User) Command number Data 1, Data 2, Setting of various data of the camera SAVE None None Save the setting data of the camera INIT None None Initiate the camera data to factory settings There are three kinds of commands, GU (Get User) command to obtain the camera data, SU (Set User) command to set the camera data, and SAVE command to save the set data. Separate each command and parameter with a space Input the command in capital letters Parameters with 0x are regarded as Hexadecimal, the one with 0 are as Octal, and the one as-is are as Decimal. Do not input any letter other than numbers (0~9), Decimal Point, and Hexadecimal (0~9, and a~f). Identifiable letters from the head are to be analyzed. A command from the head to the linefeed code, [ r]or[ n], is to be regarded as one command to be analyzed. The returned command from the PC will be received by the camera, and then echoed back 10

12 Example for Get Command To get the information on the Command No.10 [Send] GU[sp]10[ r] or[ n] [Returned value] 50[ r] [ n] [Acquired data + Linefeed] [Returned value] [ r] [ n] [Linefeed] [Returned value] >[sp] [Prompt + Space] [ r]=cr(0x0d) [ n]=lf(0x0a) [sp]=space(0x20) Example for Set Command To set 30 to the Command No.10 [Send] SU[sp]10[sp]30[ r]or[ n] [Returned value] [ r] [ n] [Linefeed] [Returned value] >[sp] [Prompt + Space] Example for SAVE [Send] SAVE[ r]or[ n] [Returned value] [ r] [ n] [Linefeed] [Returned value] >[sp] [Prompt + Space] Command List Video Format 1 Function Command No. Data 0: 1080p 60fps LevelA 1: 1080p 59.94fps LevelA 2: 1080p 50fps LevelA 3: 1080p 60fps LevelB 4: 1080p 59.94fps LevelB 5: 1080p 50fps LevelB 6: 1080i 60fps 7: 1080i 59.94fps Video 1 8: 1080i 50fps Format 9: 1080p 30fps 10: 1080p 29.97fps 11: 1080p 25fps 12: 1080p 24fps 13: 1080p 23.97fps 14: 720p 60fps 15: 720p 59.94fps 16: 720p 50fps Factory Description setting 6 Set the format of the video output 11

13 AE 2~19 Function Command Factory Data No. setting Description Gain Mode 2 0: Manual 1: Auto 1 Set the Gain Mode Gain Value 3 Factor x 0 x Set the Gain value when Gain Mode is set to MANUAL. 0x times (0[dB]): 0x (65536) *Refer to 10.4 Table for Gain Setting Value Max Gain 4 Factor x 0 x x Set the Max Gain when Gain Mode is set to AUTO. ( ) 1.0 times (0[dB]): 0x Shutter Mode 5 0: MANUAL 1: AUTO 1 Set the Shutter mode. Set the Shutter value when Shutter Mode is set to Shutter Value 6 MANUAL. Exposure time 0x4444 *Shutter speed slower than 1/60s will be limited by the [sec] x 0x (17476) frame rate corresponding to the video output format. 1/25s ~ 1/8000s 1/60s And, the shutter is limited to 1/25s at 24fps. *Refer to 10.4 Table for Gain Setting Value Shutter Limit 7 Set the range when Shutter Mode is set to AUTO. Max: 1 st Param = Max, 2 nd Param = Min 0x4444 Same as Shutter example) SU 7 0x4444 0x83 (17476) Value. *Shutter speed slower than 1/60s will be limited by the 1/60s Max. value (data 1) frame rate corresponding to the video output format. Min: Min. value (data 2) And, the shutter is limited to 1/25s at 24fps. 0x83(131) Setting value will not be reflected if Max > Min is set. 1/8000s *Refer to 10.4 Table for Gain Setting Value 0: Average metering 1: Center Weighted metering Metering 8 2: Spot metering 1 Set the Metering mode Mode 3: Backlight compensation (4: Evaluation metering) X value: 0~15 8 Set the XY value at Spot metering. Spot Block 9 1 st Param = X value, 2 nd Param = Y value Y value: 0~15 8 Example) SU AE Speed 10 0~ Set the convergence speed of AE. AE Level 11 0~ Set the convergence level of AE. 0: OFF Flicker Cancel 12 1: ON 0 Set the Flicker cancel Gain Value, -1 Reduce 1dB from current Gain value. 13 none Plus Minus 1 Increase 1dB from current Gain value. Shutter Value, -1 Reduce 1/4EVStep from current Shutter value. 14 none Plus Minus 1 Increase 1/4EVStep from current Shutter value. 12

14 WB 20~29 Function Command Factory Data No. setting Description 0: Auto 1: Auto(Outdoor) 2: DayLight 3: Cloudy 4: Shade 5: Tungsten 6: Fluorescent (White) 7: Fluorescent (Neutral White) WB Mode 20 8: Fluorescent (Day light) 9: Auto (ATW) 10: One-Push 11: Manual 12: Preset1 13: Preset2 14: Preset3 15: Preset4 16: Preset5 0 Set the White balancing mode 1: Preset1 Preset 21 (Write Only) 2: Preset2 Store the current WB value as preset value. 3: Preset3 none The stored value will not be saved until SAVE is 4: Preset4 executed. 5: Preset5 Blue Gain 22 0~800(%) 161 Set the B Gain value when WB Mode is set to MANUAL Red Gain 23 0~800(%) 220 Set the R Gain value when WB Mode is set to MANUAL. (Write Only) One Push 24 1: Trigger Start none Function starts operation when WB mode is set to Trigger One-Push. 13

15 Image quality 30~59 Function Command Factory Data No. setting Description 0: Off 1:1 2:2 Edge Level 30 3:3 4:4 5:5 6:6 7:7 3 Set the Edge level. 0: Contrast -2 Contrast 35 1: Contrast -1 2: Standard 3: Contrast +1 4: Contrast +2 2 Set the Contrast level. Master Pedestal ~ Set the Master pedestal. Red Pedestal ~ Set the Red pedestal. Green Pedestal ~ Set the Green pedestal. Blue Pedestal ~ Set the Blue pedestal. Red Balance 41 0~ Set the Red balance. Green Balance 42 0~ Set the Green balance. Blue Balance 43 0~ Set the Blue balance. Color Saturation 45 0~ Set the Color saturation. Noise Reduction 50 0 : Noise reduction OFF 0 Set the Noise Reduction. 1 : Noise reduction ON 0: Standard Color Correction 52 1: Fluorescent light 2: Tungsten lamp 0 Set the Color correction. Color Suppression 53 0~7 5 Set the Color suppression level. Lens Control 60~ Function Command No. Iris Mode 61 0: OPEN 1: AUTO Data Factory Description setting 0 Set to AUTO when a DC Iris Lens is used. 14

16 OSD Related 90 ~ Function Command No. OSD UP Button 90 OSD DOWN Button 91 OSD R Button 92 OSD L Button 93 OSD CENTER Button 94 Menu Color 95 Select Color 96 Data 0: 1 push operation 1: Continuous push 0: 1 push operation 1: Continuous push 0: 1 push operation 1: Continuous push 0: 1 push operation 1: Continuous push 0: 1 push operation 1: Continuous push 0: Black 1: Blue 2: Green 3: Cyan 4: Red 5: Magenta 6: Yellow 7: White 0: Black 1: Blue 2: Green 3: Cyan 4: Red 5: Magenta 6: Yellow 7: White Factory Description setting None None Command to operate OSD. Send the commands every 60msec for continuous push None None None Use as Set button. 7 Set the Font Color of OSD Menu. - Set the Font Color of Highlighted Characters on OSD. - The function becomes error if the color same as the 3 Menu Color is set, as the selected character will not be able to distinguish. 15

17 Others 100 ~ Function Command No. Data Camera Setting Store 100 0~3 Camera Setting Load 101 0~3 LTC OFF/ON 103 0: OFF 1: ON LTC Reset 104 1: Reset Factory Setting Description - 4 sets Camera setting value can be stored. - The stored setting value will not be saved until the Initial SAVE command is executed. operation - The stored data and setting value will not be 0 initiated to factory setting in INIT command execution. - Load the setting value which was stored at Camera Settings Store. Initial - The setting value will not be initiated to factory operation setting in INIT command execution. 0 *The current setting value will be replaced by the value stored in Camera Setting Store when the Camera Setting Store is run. 0 Set the Signal insertion of LTC. (Write Only) Reset the Internal Timer of LTC. Command list (without command no.) Function Command Factory Data No. Setting SAVE None None None INIT None None None 1: Microcomputer GVI None Version None 2: FPGA Version SDDW None Description Save the Camera setting. Use capital letter for SAVE. *Only one defective pixel correction data table will be saved. Initiate the camera setting to factory setting. Use capital letter for INIT Obtain Firmware version. String such as 0.1 will be returned. Starting Defective pixels detection. (Refer to 9. Defective Pixels Correction function for detailed operation) 16

18 10.4. Table for Setting Value Gain Setting Gain Value Factor db Gain Value (Factor x 0 x 10000) DEC HEX F A A F C EB D CBF D A A F F FACD A B504F CB2FF E411F F59A A A09E FE C823E

19 Shutter Setting Shutter Value Exposure shutvalue Time (sec x 0 x ) (sec) DEC HEX Open Depend on Video Format 1/ / / / / / / / D82 1/ F5 1/ C4 1/ C1 1/ / BB3 1/ / A6 1/ / BB 1/ C 1/ D 1/ / AE 1/

20 11. Camera Operation with OSD Camera can be operated through OSD menu by connecting the remote controller (option) to the camera's remote control terminal and display the OSD menu on the monitor screen. Note: Camera operation with OSD requires a remote controller which is sold separately Switching operation of the OSD menu display by remote controller [CENTER] To display OSD Main Menu on the monitor screen Also can be used to confirm the menu selected. [ ] Move the selection up one line on the screen. [ ] Move the selection down one line on the screen. [ ] Change the item of the selection [ ] Change the item of the selection OSD Menu Indication A [ ] mark is attached at the line last, which is the item that a sub-menu can be displayed by the CENTER button. A ] mark is attached at the line last, which is the item can be settled by CENTER button. [ OSD Menu List Main Menu Set Up Menu Selection Item Description EXIT None None End the OSD Menu by pressing CENTER 1080p 60fps (Level A) 1080p 59.94fps (Level A) 1080p 50fps (Level A) 1080p 60fps (Level B) 1080p 59.94fps (Level B) 1080p 50fps Set the Video format. Output Format Set Video Format (Level B) Pressing ] or ] button to select Video [ [ 1080i 60fps Format, and press CENTER button to set and 1080i 59.94fps to reflect the setting. 1080i 50fps 1080p 30fps 1080p 29.97fps 1080p 25fps 1080p 24fps 1080p 23.97fps 720p 60fps 720p 59.94fps 720p 50fps 19

21 Main Menu Set Up Menu Selection Item Description Gain Mode Manual/Auto Set the setting of Gain Mode Gain Value Gain Max Value 0~30dB 0~30dB Set the Gain Value when Gain Mode is set to Manual. Refer to *1, *2 Set the Max Gain Value when Gain Mode is set to Auto. Refer to *1, *2 Gain/Shutter/IRIS Shutter Mode Manual/Auto Set the setting of Shutter Mode. 1/25 1/30 1/36 1/42 1/50 1/60 1/75 1/90 1/100 1/105 1/120 1/125 1/150 1/180 1/210 1/250 1/300 Set the Shutter Value when Shutter Mode is set to Manual. Shutter speed slower than 1/60s will be limited by Shutter Value 1/350 the frame rate corresponding to the video output 1/420 format. And, the shutter is limited to 1/25s at 1/500 24fps. 1/600 1/700 Refer to *1, *2 1/840 1/1000 1/1200 1/1400 1/1700 1/2000 1/2400 1/2800 1/3400 1/4000 1/4800 1/5600 1/6800 1/

22 Main Menu Set Up Menu Selection Item Description Same items as Set the Min Shutter Limit when Shutter Mode is set Shutter Min Shutter Value to Manual. Limit selection Refer to *1, *2 Shutter Max Limit Same as Shutter Value Set the Max Shutter Limit when Shutter Mode is set to Auto. Refer to *1, *2 Gain/Shutter/IRIS Define the Shutter Limit by pressing CENTER Set Shutter button. None Limit The setting value will not be reflected when Max < Min is set. Set Iris Mode. Iris Mode Auto/Open Auto: Open: AE Speed 0~100 Set the convergence speed of AE. AE Level 0~100 Set the convergence level of AE. Average Set Metering Mode. Metering Mode Center Weighted Spot Backlight Comp Average:Average metering Center Weighted:Center Weighted metering Spot:Spot metering Backlight Comp:Backlight compensation Spot Block X 0~15 Set the X Block value when Metering Mode is set to Spot. Spot Block Y 0~15 Set the Y Block value when Metering Mode is set to Spot. Set Spot Block None Define the Spot Block X, Y by pressing CENTER button. Flicker Cancel ON/OFF Set Flicker Cancel *1: For more detailed setting, use Serial Command for setting. *2: The setting value set by Serial Command will be reflected at Key operation. 21

23 Main Menu Set Up Menu Selection Item Description Auto Outdoor Daylight Cloudy Shade Tungsten Flw: Fluorescent (White) Fln: Fluorescent Pressing ] or ] button to select WB Mode, and [ [ (Neutral White) WB Mode perform the setting. Fld: Fluorescent (Day light) Auto(ATW) White Balance One push Manual Preset1 Preset2 Preset3 Preset4 Preset5 WB Red Gain 0~800 Set the Red Gain/Blue Gain when WB Mode is set to WB Blue Gain 0~800 Manual Only available when One Push is selected at WB One Push None Mode. Press CENTER button to start One Push Start WB. Use ] or ] button to select the preset number, [ [ Set Preset 1~5 and press CENTER button to save the WB Number information which is reflected on the screen. 22

24 Main Menu Set Up Menu Selection Item Description Image Control LTC Red Balance 50~150 Set Red Balance. Refer to *3 Green Balance 50~150 Set Green Balance. Refer to *3 Blue Balance 50~150 Set Blue Balance. Refer to *3 Master Pedestal -100~100 Set Master Pedestal. Red Pedestal -100~100 Set Red Pedestal. Green Pedestal -100~100 Set Green Pedestal. Blue Pedestal -100~100 Set Blue Pedestal. Edge Level 0~7 Set Edge Level. 0: OFF Contrast -2 Contrast Contrast -1 Standard Contrast +1 Contrast +2 Set Contrast. Noise Set Noise Reduction. OFF/ON Reduction Color noise reduction OFF/ON Color Saturation 0~200 Set Color Saturation. Standard Color Correction Fluorescent light Tungsten lamp Set Color Correction. Color Suppression 0~7 Set Color Suppression. LTC ON/OFF Set LTC to ON or OFF. Set LTC Reset None Reset LTC by pressing CENTER button. *3: 0~200 setting value is available when set via COMMAND. 23

25 Main Menu Set Up Menu Selection Item Description Default Set By pressing CENTER button, the OSD color setting will be (White & None returned to factory setting color. Cyan) User Setting Set OSD Menu color. Black Blue Green Cyan Use ] or ] button to select the OSD Menu color. [ [ Menu Color Red OSD Color Change Magenta Yellow White Highlight Same as Menu Use [ ] or [ ] button to select the highlight color of Color Color selected OSD Menu. Set Color None Press CENTER button to set the Menu Color, and the Highlight Color. Menu Color and Highlight Color will not be set if the same color has been selected for both Menu and Highlight. INIT None None Initiate the Camera setting to Factory Setting by pressing CENTER button. Set Save Data 0~3 Selected preset number will be saved by pressing CENTER button. Really? NO/YES Inquiry if user really wants to Save the preset selected. Save/Load Execute selection of SAVE NO/YES and return to Enter None previous screen. Get Save Data 0~3 Pressing CENTER button to call the data of the selected preset number and reflect the data on the screen. 24

26 12. Factory Settings Function Default Data Video Format Setting 1920 x Gain Mode Auto Manual Gain 65536(0dB) Max Gain (30dB) Shutter Mode Auto Shutter Limit Max 17476(1/60) Shutter Limit Min 131(1/8000) Manual Shutter 17476(1/60) Iris Open AE Mode Center-Weight Spot Block X=8,Y=8 AE Level 50 AE Speed 50 Flicker Cancel OFF White Balance Setting Auto Manual Red Gain 220 Manual Blue Gain 161 Color Correction Standard Color Suppression 5 Color Saturation 100 Edge Enhancement 3 Noise Reduction 0 Contrast Standard Master Pedestal 0 Pedestal(RGB) 0 Color Balance (RGB) 100 LTC OFF OSD Menu Color White OSD Select Color Cyan 25

27 13. Dimensions (Unit: mm ) 26

28 14. Case for Indemnity (Limited Warranty) The term of warranty of this product is within 1.5 years after shipping out from our factory. We shall be exempted from taking responsibility and held harmless for damage or losses incurred by the user in the following cases. In case damage or losses are caused by fire, earthquake, or other acts of God, acts by third party, deliberate or accidental misuse by the user, or use under extreme operating conditions. In case indirect, additional, consequential damages (loss of business interests, suspension of business activities) are incurred as result of malfunction or non-function of the equipment, we shall be exempted from responsibility for such damages. In case damage or losses are caused by failure to observe the information contained in the instructions in this product specification & operation manual. In case damage or losses are caused by use contrary to the instructions in this product specification & operation manual. In case damage or losses are caused by malfunction or other problems resulting from use of equipment or software that is not specified. In case damage or losses are caused by repair or modification conducted by the customer or any unauthorized third party (such as an unauthorized service representative). Expenses we bear on this product shall be limited to the individual price of the product. 15. CMOS Pixel Defect CMOS pixel defects might be visible with time of usage of the products. The cause of the CMOS pixel defects is the characteristic phenomenon of CMOS itself and CIS is exempted from taking any responsibilities for them. 16. Product Support When defects or malfunction of our products occur, and if you would like us to investigate on the cause and repair, please contact your distributors you purchased from to consult and coordinate. Camera control software is downloadable via our web but we shall be exempted from taking responsibility and held harmless for damage or malfunction of your hardware and software caused by using this control software. The purpose of the control software prepared is for you to check operation and evaluate our products. Please be noted that CIS does not customize the program nor provide source code. URL: 27