WRT4000 Series Cellular Wireless Routers

Transcription

1 WRT4001A WRT4011A WRT4001A-DC WRT4000-DIN March 2009 WRT4002A WRT4012A WRT4002A-DC codes WRT4000-PM codes WRT4003A WRT4013A WRT4003A-DC codes WRT4000-ANT codes WRT4004A WRT4014A WRT4004A-DC codes WRT4000-ANT-KIT codes WRT4000 Series Cellular Wireless Routers Quick Start Guide Single box solution for Internet/WAN access, VPN, firewall, Ethernet switching, and legacy protocol to IP internetworking. Customer Support Information Order toll-free in the U.S.: Call BBOX (outside U.S. call ) FREE technical support 24 hours a day, 7 days a week: Call or fax Mailing address: Black Box Corporation, 1000 Park Drive, Lawrence, PA Web site: info@blackbox.com

2 STEP A: Collect the Items Needed for Installation 1A. Get everything out of the shipping box. It should contain: This Quick Installlation Guide WRT4000 Series Cellular Wireless Router 1 DC connector set or AC power adapter Antennas included 2A. Get additional items required to install the WRT4000 Series Cellular Wireless Router. You will need: Computer with Web-browsing software 2 Ethernet cable Subscriber Identity Module (SIM) 3 Cellular wireless network account 3 NOTES: 1 This quick installation guide assumes that there will be one embedded cellular module. 2 JavaScript must be enabled in the Web browser. 3 The embedded cellular module must have a cellular wireless network account and a Subscriber Identity Module (SIM) for that account. Order each SIM from a cellular wireless network provider. SIMs are not shipped with the Router. STEP B: Ports on the WRT4000 Series Cellular Wireless Router Chassis USB Port Industrial model: left slot: installed card with (2) serial ports; Commercial model: empty slots Main antenna port for internal wireless module LEDs for Power and Status LEDs for signal strength for internal wireless module LEDs (not used) Figure 1. Front panel. Page 2

3 Auxiliary antenna port for internal wireless module Port for AC power adapter input Ethernet LAN ports (eth 1) Ethernet WAN port (eth 0) Figure 2. WRT4000 Series Router back panel, AC power. Auxiliary antenna port for internal wireless module DC power connector Ethernet LAN ports (eth 1) Port for AC power adapter input Ethernet WAN port (eth 0) Figure 3. WRT4000 Series Router back panel, DC power. STEP C: Install the SIMs 1C. Make sure the WRT4000 Series Cellular Wireless Router is not connected to a power source. Then make sure no cables are connected to the router's ports. 2C. Place the router chassis on a flat, stable surface. Turn the chassis over so that it is resting on its top. 3C. Remove the screws from the sides of the chassis, and lift the chassis shell off the bottom of the chassis. Locate the SIM slot 3 socket's on the bottom of the motherboard. 4C. Swing a SIM slot 3 socket'ss hinged door open. Insert a SIM between the guides on the SIM socket s door, and slide the SIM into place. Contact pad on back of SIM Contact pads on bottom plate of SIM socket Figure 4. SIM partially inserted into the SIM socket s door. 5C. Gently close the SIM socket s door. Page 3

4 CAUTION: If the SIM is not in the correct position, the SIM socket s door will not close. In that case, remove the SIM and re-insert it in the correct position. If the SIM is positioned incorrectly, the SIM socket s door will not close If the SIM is positioned correctly, the SIM socket s door can close Figure 5. SIM in an incorrect position. Figure 6. SIM in the correct position 6C. Re-assemble the router chassis. Attach antennas to the antenna ports on the chassis front and back panels. NOTE: The antenna ports labeled MAIN 1 (on the front panel) and AUX 1 (on the back panel) hold antennas for the embedded module. STEP D: Connect and Start the WRT4000 Series Cellular Wireless Router 1D. Connect an Ethernet cable between the computer s Ethernet port and one of the Local Area Network ports (the set of LAN ports labeled eth 1 on the back of the router. 2D. To connect safely to DC power, follow the instructions in STEP E. To use only AC power, connect the AC power adapter to the router chassis, then to an AC outlet. (The chassis powers up immediately upon connection.) Then go to STEP F. STEP E: Quick Connection to DC Power For WRT4000 Series Cellular Wireless Routers that use DC power (part numbers WRT4001A-DC, WRT4002A-DC, WRT4003A-DC, and WRT4004A-DC), the DC mating connector is supplied. To connect your router to a power source, follow these instructions: 1E. Verify that the intended DC power source is the same as the input DC power indicated on the unit. The routers have 24-VDC input voltage, + 12V 1.2A Figure 7.12-VDC power input socket. 2E. Note the following (with connector orientation as shown): Page 4

5 The right position is + (for the positive wire). The left position is - (for the negative/return wire). + + positive - negative Figure 8. DC power connector with wires. 3E. Use a minimum 16 AWG wire with strip length of 0.27" (7 mm) to connect to each position. 4E. Install a cable tie through the holes on the bottom of the shell assembly and around the power cables, as shown. 5E. Install the snap-on cover, and plug the DC power connector assembly into the DC power socket on the back of the router chassis. Figure 9. Top section of shell above cabled lower shell assembly. 6E. If an AC adapter is also used to power the router, plug the AC barrel connector into the mating socket labeled +5V. Page 5

6 STEP F: Login to the WRT4000 Series Cellular Wireless Router 1F. On the computer, open a Web browser. In the browser s address field, type the router s default LAN IP address ( ) and press the Enter key. Accept cookies for the WRT4000 Series Cellular Wireless Router management system. 2F. When the browser displays the WRT4000 Series Cellular Wireless Router system login screen, type the default user name (root) and password (Blackbox). Then press the Enter key or click the screen s button to Log In (at the far right, below the entry fields). Figure 10. WRT4000 Series Cellular Wireless Router system login screen. STEP G: Activate the Modules on the Cellular Networks 1G. If the SIM package did not include instructions, go to STEP 5G. 2G. If the SIM package included instructions to configure the Access Point Name (APN), select the Network tab, then the Interfaces tab. 3G. On the Interface Overview screen, identify the row for the cellular wireless module, and select the Edit button near the right side of the module s row. 4G. On the module s Interface Configuration Screen, select the correct Protocol and Service Type; then type the APN as shown on the SIM package. Leave the other fields as they are. 5G. Leave the chassis powered up for 30 minutes to allow automatic over-the-air (OTA) activation to occur. STEP H: Log Out of the WRT4000 Series Cellular Wireless Router To close the WRT4000 Series Cellular Wireless Router management session, select the tab to Log Out. NOTE: If the management system is unattended for several minutes, the session will log out automatically. To resume management, log in again. Page 6

7 NOTES Page 7

8 Black Box Tech Support: FREE! Live. 24/7. Tech support the way it should be. Great tech support is just 60 seconds away at or blackbox.com. About Black Box Black Box provides an extensive range of networking and infrastructure products. You ll find everything from cabinets and racks and power and surge protection products to media converters and Ethernet switches all supported by free, live 24/7 Tech support available in 60 seconds or less. Copyright Black Box Corporation. All rights reserved. Black Box and the Double Diamond logo are registered trademarks of BB Technologies, Inc. Any third-party trademarks appearing in this manual are acknowledged to be the property of their respective owners. WRT4000-Series-Cellular-Wireless-Routers-Quick-Start-Guide, version 2