Introduction to USB Type-C & Power Delivery

Transcription

1 Power Supply Design Seminar (Demo Hall Presentation) Introduction to USB Type-C & Power Delivery TI Literature Number: SLUP , 2017 Texas Instruments Incorporated Power Seminar topics and online power training modules are available at:ti.com/psds

2 Introduction to USB Type-C & Power Delivery Focus on Charging Applications Deric Waters, System Engineer

3 Agenda Introduction to USB Type-C and Power Delivery Detailed discussion of a USB Type-C universal adaptor o Including conceptual schematic of a single and dual port AC/DC adaptor. 2

4 The USB Connectors C-to-C, C-to-A and C-to-B cables are defined. USB2.0 One size for USB2.0, 3.0, 3.1 Type-A Type-B Mini-B Micro-B USB3.0 USB2.0 USB3.1 Type-A Type-B Micro-B DisplayPort Power Delivery 3

5 USB Type-C Flippable Receptacle Interface Note: Determining the plug s polarity is only necessary if USB SS or DP Alt Mode is used. High Speed Data, USB SS, SS+ TX or DP Alt Mode USB2 Data Sideband Use, not used for USB, AUX for DP High Speed Data USB SS, SS+ RX or DP Alt Mode SBU SBU Cable Ground Cable Bus Power Configuration channel, for cable attach, orientation, role detection, and current mode One becomes VCONN to supply power for cable or adaptor 4

6 USB Power Delivery over USB Type-C Precedence Mode of Operation Nominal Voltage Maximum Current Highest USB PD Up to 20 V Up to 5 A Priority of Power Modes USB Type-C 3A 5 V 3 A USB Type-C 1.5A 5 V 1.5 A USB BC1.2 5 V Up to 1.5 A USB 3.1 5V 900 ma Lowest USB 2.0 5V 500 ma 5

7 USB Power Delivery (PD) Features Why use USB PD? Typical PD flow Enables higher voltage, up to 20V 5V, 9V, 15V, and 20V satisfy most customer needs. Up to 100W power over USB cable Which port provides power is negotiable DFP can be provider or consumer. UFP can be provider or consumer. Efficient power management across multiple peripherals DFP has cold socket to conserve power Co-existence with legacy USB products Enables Alternate Modes VBUS initially defaults to 5V, 500mA power supply USB Power Delivery negotiation over CC wire Power supplied over VBUS at the rate negotiated Not related to power, but USB PD required 5V 5V 20V 6

8 The USB Type-C Ecosystem Power Role Source- Only Source (Default) DRP Sink (Default) Sink- Only DFP = Downward Facing Port DRP = Dual Role Power DRD = Dual Role Data UFP = Upward Facing Port No Data Wall Outlet Charger Power Bank USB Powered Accessories Data Role Host DFP DRD Desktop PC/Server USB Hub Infotainment Laptop Laptop Mobile Devices Device UFP Monitor, TV Docking Station Desktop HDD USB Hub USB Devices Accessories Mobile HDD 7

9 Focus on Source-Only Application There are many different applications that require different silicon solutions under the USB Type-C umbrella. o Laptops, docking station, monitors, tablets, etc. One benefit of the wide-spread adoption of this open standard is a realistic path to a universal charger and e-waste reduction. o One connector instead of the proliferation of different adaptors for different devices o 300,000 tons of e-waste goes to landfills every year (according to UN) 8

10 45W Single-port AC/DC Source receptacle VBUS VBUS 5V, 9V, or 15V Fly-Back VCON CC ESD CC1 CC2 Voltage Selection TX2/RX2 TX1/RX1 D+ D- SBU handles USB PD messaging handshake Selects voltage from fly-back power supply controls the FET switch on VBUS. TPS25740A is an example of a PD controller FET is required to prevent high voltage on VBUS until the right time. Back-to-Back FETs required by USB Type-C for adaptors with receptacle. All Adaptors must be able to drive VBUS to 0V when nothing is attached. Many types of devices can be inserted into a universal charger, so it is critical to prevent putting high voltage on VBUS until the right time. TI Design: PMP20211 (45W), PMP11451 (60W), PMP

11 45W Single-port AC/DC Source Captive Cable VBUS VBUS 5V, 9V, or 15V Fly-Back CC VCON ESD CC1 CC2 Voltage Selection TX2/RX2 TX1/RX1 D+ D- SBU handles USB PD messaging handshake Selects voltage from fly-back power supply controls the FET switch on VBUS. TPS25740A is an example of a PD controller FET is required to prevent high voltage on VBUS until the right time. Only one FET required by USB Type-C for adaptors with captive cable. All Adaptors must be able to drive VBUS to 0V when nothing is attached. Many types of devices can be inserted into a universal charger, so it is critical to prevent putting high voltage on VBUS until the right time. TI Design: PMP20211 (45W), PMP11451 (60W), PMP

12 AC/DC Adaptor Application Below is a schematic for an AC/DC USB Type-C Power Delivery adaptor. o The TPS25740 is an example of a. CTL1 and CTL2 are pulled low or left open-drain to select the output voltage. T1 From AC Mains DVC LDO + CB1 P VDD CB2 P HV T1 DS COUT CSD17579Q3A RSLEW RS CX3 10µF 100Ω VBUS D+ D- Type-C Plug Isolated AC/DC Flyback P RS1 RS2 CDD CDD1 P RF6 RF5 UCC28740 VS DRV CS FB GND RLC M1 VB RCS CIO ROB CIZ TLV431 RFBU RFBL RFBL2 RFBL1 VPWR VDD GDNG CTL1 CTL2 HIPWR PCTRL CSLEW GDNS TPS25740 VAUX VBUS VTX DVDD ISNS EN_IN DSCG RDSCG CC1 CC2 UFP PSEL EN12Vb GND AGND CRX Port Status indicator 100kΩ 220kΩ CAUX CTX CDV TI Design: PMP20211 (45W), PMP11451 (60W), PMP

13 Typical Behavior upon Attachment The CC2 / CC line shows the voltages on the configuration channel between the sink and a source that applies VCONN to the cable. t1: the cable is attached. t2: the source confirms a valid sink is attached, then applies 5V to VBUS and VCONN. t4 t3: USB Type-C 3A advertisement begins & USB PD messaging begins on CC line t4: VBUS voltage is increased to negotiated level. AC/DC Adaptor (TPS25741 EVM) Sink (Apple MacBook) t1 t2 t3 12

14 PD Voltage Transition Requirements If Negotiated Voltage (NV) > 5V vsrcnew = ± 5% of NV If Negotiated Voltage (NV) = 5V 4.75V < vsrcnew < 5.5V vsrcvalid =VSrcNew ± 0.5V vsrcslewpos < 30mV/µs tsrcsettle = 275ms tsrcready = 285ms With External FET, positive and negative slew rate can be controlled via R & C selection 13

15 VBUS in Faulty System DS COUT CSD17579Q3A RSLEW RS VBUS Consider the AC/DC adaptor when the CTL node gets shorted due to some faulty condition. The should disable the FET to prevent VBUS voltage raising too high before a USB PD negotiation. ROB CIZ TLV431 RFBU RFBL RFBL2 RFBL1 VPWR GDNG GDNS ISNS VBUS CTL1 CTL2 CSLEW TPS25740 DSCG RDSCG VBUS hits OVP trip-point. NFET gets disabled, limiting the max voltage on VBUS. Due to a fault, the reference node gets grounded. Causes flyback output to go high voltage. Sink plugged in at time 0 Try to turn on VBUS again after 0.8 sec. 14

16 Dual-Port Options (1/2) Each port marked as 45W capable Both ports always offer exactly 45W 45W Each port marked as 22.5W capable A port offers 45W only if the other port is empty 45W 5V, 9V, or 15V DC/DC (Buck) 5V, 9V, or 15V DC/DC (Buck) (TPS25740A) CTL1 / CTL2 45W (TPS25740A) CTL1 / CTL2 45W 5V, 9V, or 15V DC/DC (Buck) 5V, 9V, or 15V DC/DC (Buck) (TPS25740A) CTL1 / CTL2 Fly-Back 90W (TPS25740A) CTL1 / CTL2 Similar TI Design: PMP20271 (uses dual Buck LM5140) Fly-Back 45W 15

17 Dual-Port Options (2/2) Each port marked as 15W capable A port offers 27W only if the other port is empty Best efficiency, lowest BOM. Each port marked as 22.5W capable A port offers 45W only if the other port is empty 45W 5V, or 9V 5V, 9V, or 15V DC/DC (Buck) (TPS25740A) CTL2 (TPS25740A) CTL1 / CTL2 45W 5V, or 9V 5V, 9V, or 15V DC/DC (Buck) (TPS25740A) CTL2 Fly-Back 30W (TPS25740A) CTL1 / CTL2 Similar TI Design: PMP20271 (uses dual Buck LM5140) Fly-Back 45W 16

18 Summary USB Type-C is bringing major changes to the ubiquitous USB eco-system and has created a realistic possibility for a universal charger for all consumer electronics. USB Power Delivery is extending the applicability of USB into non-traditional applications. Even for the simplest USB Power Delivery application (charging) there are a number of options and features that must be tuned per system requirements. 17

19 Appendix Buck DC-DC Solutions - Controllers Part Number Description Vin (Min) (V) Vin (Max) (V) Vout (Min) (V) Vout Iout (Max) (V) (Max) (A) Regulated Outputs (#) Switching Frequency (Min) (khz) Switching Frequency (Max) (khz) Special Features TPS40304 TPS V to 20V Wide Input Synchronous Buck Controller Dual Output or Two-phase Synchronous Buck Controller Enable, Power Good, Pre- Bias Start-Up, Synchronous Rectification Enable, Frequency Synchronization, Remote Sense LM5140-Q1 Dual Output Synchronous Buck Low standby current 18

20 TI Worldwide Technical Support Internet TI Semiconductor Product Information Center Home Page support.ti.com TI E2E Community Home Page e2e.ti.com Product Information Centers Americas Brazil Mexico Phone +1(512) Phone Phone Fax Internet/ +1(972) support.ti.com/sc/pic/americas.htm Europe, Middle East, and Africa Phone European Free Call ASK-TEXAS ( ) International +49 (0) Russian Support +7 (4) Note: The European Free Call (Toll Free) number is not active in all countries. If you have technical difficulty calling the free call number, please use the international number above. Fax Internet Direct Japan +(49) (0) Phone Domestic Fax International Domestic Internet/ International Domestic support.ti.com/sc/pic/japan.htm Asia Phone International Domestic Toll-Free Number Note: Toll-free numbers do not support mobile and IP phones. Australia China Hong Kong India Indonesia Korea Malaysia New Zealand Philippines Singapore Taiwan Thailand International Fax Internet or support.ti.com/sc/pic/asia.htm Important Notice: The products and services of Texas Instruments Incorporated and its subsidiaries described herein are sold subject to TI s standard terms and conditions of sale. Customers are advised to obtain the most current and complete information about TI products and services before placing orders. TI assumes no liability for applications assistance, customer s applications or product designs, software performance, or infringement of patents. The publication of information regarding any other company s products or services does not constitute TI s approval, warranty or endorsement thereof. B The platform bar and E2E are trademarks of Texas Instruments. All other trademarks are the property of their respective owners. SLUP360

21 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as components ) are sold subject to TI s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or enhanced plastic are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS Products Applications Audio Automotive and Transportation Amplifiers amplifier.ti.com Communications and Telecom Data Converters dataconverter.ti.com Computers and Peripherals DLP Products Consumer Electronics DSP dsp.ti.com Energy and Lighting Clocks and Timers Industrial Interface interface.ti.com Medical Logic logic.ti.com Security Power Mgmt power.ti.com Space, Avionics and Defense Microcontrollers microcontroller.ti.com Video and Imaging RFID OMAP Applications Processors TI E2E Community e2e.ti.com Wireless Connectivity Mailing Address: Texas Instruments, Post Office Box , Dallas, Texas Copyright 2016, Texas Instruments Incorporated