Innovative PBX Accessories. for Any PBX System NATCOMM USA QUALITY AND INNOVATION ...YOUR PBX ACCESSORIES PARTNER INTERCOMS WITH COLOUR CCD CAMERA

Transcription

1 NATCOMM USA QUALITY AND INNOVATION SINCE 1990 Innovative PBX Accessories for Any PBX System INTERCOMS FOR EXTENSION, FXS OR ATA CONNECT INTERCOMS FOR TRUNK OR FXO CONNECT INTERCOMS WITH COLOUR CCD CAMERA INTERCOMS WITH PEDESTRIAN KEYPAD MESSAGE ON HOLD WITH OR WITHOUT IP UPDATE MESSAGE ON HOLD WITH AFTER HOURS MESSAGE AUTOMATIC CALL ATTENDANT AUTOMATIC ANNOUNCEMENT DEVICE PA INTERFACE UNIT PRE-AMP WITH ANTI-POP PULSE DECADIC TO DTMF CONVERSION DIALER RING BOOSTER FOR DEVICES THAT WONT ANSWER TWO LINE SWITCH. CONNECT 1 DEVICE TO 2 LINES INTELLIGENT STROBE AND LOUD SPEAKER ALARM INCOMING RING INDICATOR WITH STROBE AND OR ALARM OFF HOOK INDICATOR WITH STROBE AND OR ALARM TELEPHONE LINE MONITOR WITH STROBE AND OR ALARM PRIVACY SWITCH PRIORITY SWITCH FOR EMERGENCY DEVICES RING DELAY SWITCH, CONNECTS AFTER 0-15 RINGS FAX SWITCH, EFTPOS SWITCH...YOUR PBX ACCESSORIES PARTNER

2 Natcomm PBX Accessories We are pleased to provide you with this copy of our 2017 PBX Accessories Catalogue. Our products are the result of over 25 years of continuous development from our combined USA & Australian development engineers and product specialists. NATCOMM Accessories will operate with ALL PBX Systems including PSTN, ISDN, IP & Cloud. They are designed to Connect to Standard Analog Extensions ortrunk inputs and will also operate with FXS, FXO and ATA ports. During 2017, several unique SIP connect products will be introduced, providing for a range of SIP Door Phones, a SIP Paging Switch. SIP Controlled Relays and a SIP Ring Indicator. Each product is provided with an Unconditional 30 Day Money Back Guarantee. If you are not completely satisfied with one of our solutions, just call us and we will solve your concerns or refund your purchase. Each product is provided with a TWO YEAR WARRANTY. Our products are Engineered to last over years. However, In the unlikely event that our product has failed within the warranty period, we will provide you with an expedient repair or exchange. All products have been tested to meet all necessary USA FCC requirements and Industry Canada IC requirements. Our Products are provided with an Attractive Wholesale Price, to allow you to enjoy a good profit margin as well as your Installation Charge. Our Comprehensive Web Site will allow you to Register as a Reseller and then allow you to quickly and Easily purchase our products On Line at Wholesale Prices. Your Business and Delivery Details are automatically saved for your ongoing purchases and you can easily edit these details at any time. We only sell the products that we design and manufacture. This allows us to provide you with Expert Technical Support for our Products and their Applications. Just call us on ph (800) (9AM-5PM Pacific Time). Register as a Reseller at so we can begin working as partners in providing your customers with PBX Accessory solutions of the highest Quality, Performance and Reliability. 2 YOUR PBX ACCESSORIES PARTNER

3 Innovative Accessories for ANY PBX (PSTN, ISDN, IP or Cloud) BUDGET INTERCOM PREMIUM INTERCOM WITH INTEGRATED CCD COLOR CAMERA INTEGRATED PEDESTRIAN ACCESS KEYPAD. PAGES 4-5 PAGES 4-5 PAGES 4-5 PAGES 4-5 PBX TRUNK CONNECTION (OR FXO) PBX EXTENSION CONNECTION (OR FXS, ATA) PROGRAMMABLE LOCK CONTROL SINGLE OR DUAL DIAL OUT INTERCOM OPERATION PAGE 6 PAGE 7 PAGE 7 PAGE 7 DIGITAL MESSAGE ON HOLD ON HOLD & AFTER HOURS MESSAGE CALL ATTENDANT ANNOUNCEMENT PLAYER PAGING SWITCH ANALOG AND SIP MODELS PAGES 8-9 PAGE 10 PAGE 11 PAGES DIAL IN RELAY & ACCESS CONTROL DECADIC to TONE DIALER RING BOOSTER AUTOMATIC TWO LINE SWITCH PAGES PAGE 16 PAGE 17 PAGE INCOMING RING INDICATOR ANALOG AND SIP MODELS OFF HOOK INDICATOR TELEPHONE LINE MONITOR STROBE & SPEAKER ALERT ACCESSORIES PAGE 20 PAGE 21 PAGE 22 PAGES 23 PRIORITY SWITCH PRIVACY SWITCH RING DELAY SWITCH EFT-POS SWITCH PBX FAX SWITCH PAGES PAGE PAGE PAGES SUPPLYING QUALITY PRODUCTS SINCE 1990 TWO YEAR FACTORY WARRANTY 3

4 Door Phone Intercom Options for Analog or SIP operation Model DP1 Surface mounting door phone Plastic injection moulded casing 2 Wire connectivity Basic audio clarity and volume Budget solution (H) 5.2 inch (W) 3.9 inch (H) 132 mm (W) 100 mm Model DP2 Flush mounting door phone compact size. High Quality 316 marine grade stainless steel fascia. Surface Mounting Kit is available. (See page 5) 4 Wire connectivity Premium audio clarity and volume Capacitive touch switch activation (H) 8.0 inch (W) 4.2 inch (H) 204 mm (W) 107 mm Model DP4 Flush mounting door phone standard size Incorporates a low light, high resolution CCD colour camera Surface Mounting Kit is available. (See page 5) High Quality 316 marine grade stainless steel fascia. 4 Wire connectivity Premium audio clarity and volume Capacitive touch switch activation Supplied with a WMB3 wall mount box to assist and speed up installation (H) 10.4 inch (W) 5.1 inch (H) 264 mm (W) 130 mm Model DP5 Flush mounting door phone standard size Incorporates an integrated touch sensitive pedestrian access keypad Surface Mounting Kit is available. (See page 5) Allows for up to 100 separate 4 to 6 Digit user pin codes High Quality 316 marine grade stainless steel fascia. 4 Wire connectivity Premium audio clarity and volume Capacitive touch switch activation Supplied with a WMB3 wall mount box to assist and speed up installation (H) 10.4 inch (W) 5.1 inch (H) 264 mm (W) 130 mm ALL DOOR PHONES CONNECT TO ALL NATCOMM ANALOG OR SIP CONTROLLERS (SEE PAGES 6-9) All door phones are designed to be highly weather resistant. If the door phone is exposed to direct rain, it is recommended that you use a door phone cover for flush mounted door phones or use a surface mount kit which incorporates a rain deflector. Using a rain cover will increase the life of your exposed Door Phone. (See page 5) 4 YOUR PBX ACCESSORIES PARTNER

5 Door Phone Accessories Surface Mounting Kits Stainless Steel Surface Mounting Kits, with rain deflector are available for all door phones. Model SMK2 - is made for the DP2 Door Phone Model SMK3 - is made for the DP4, DP5 Door Phones Door Phone Covers Are available for all door phones and are recommended whenever a flush mounted door phone is exposed to direct rain. Model DPC1 - is made for the DP1 Model DPC2 - is made for the DP2 Door Phone Model DPC3 - is made for the DP4, DP5 Door Phones Wall Mount Boxes Are available for all flush mount door phones and are designed to make installation quicker and easier. Model WMB2 - is made for the DP2 flush mount door phone Model WMB3 - is made for the the DP4, DP5 flush mount door phones. A WALLMOUNT BOX IS INCLUDED WITH EVERY DP4 AND DP5 DOORPHONE (W) 3.7 inch (H) 8.9 inch (D) 1.6 inch (W) 93 mm (H) 225 mm (D) 40 mm (W) 3.3 inch (H) 7.5 inch (D) 1.6 inch (W) 85 mm (H) 190 mm (D) 40 mm SUPPLYING QUALITY PRODUCTS SINCE 1990 TWO YEAR FACTORY WARRANTY 5

6 PBX Line Trunk or FXO connection PBX Door Phone Intercom Solutions For Line Trunk (FXO) Connection Our DS1, DS2, and DS3 Model DOOR STATION controllers are designed to connect to an unused Analog Trunk Input of any PBX system. They can also be fitted to a trunk with a PSTN line connection. In this application the DS door station controller connects to a telephone line immediately ahead of the PBX telephone system. The last line is normally selected. You can then connect ONE of our range of surface mount or flush mount DOOR PHONES direct to the DOOR STATION controller. The door phones can be up to 330 yards (300 metres) from the door station controller. MODEL DS1 Trunk Connection No Lock Control When the call button of a door phone is activated, the controller will ring the attached telephone line. Upon answer communication is loud and clear, similar to a phone call and there are NO call charges, unless the call is routed to an external number. Model DS2 incorporates an internal relay which can be used to open or release a door or gate lock. Lock release time is fully programmable. Model DS3 provide two internal relays which can be used to open locks in two separate areas. The second relay can alternatively be used to SWITCH ON a light, a video camera/ recorder or any other electrical device as soon as the call button is pressed on the door phone and then SWITCH THEM OFF after the call is complete. MODEL DS2 Trunk Connection Single Lock Control Model DS3 when connected to a trunk with a PSTN connection, can also dial out to an external number when the site is unattended. Door Phone MODEL DS3 Trunk Connection Dual Lock Control Automatic Dial Out Facility Incoming Telephone Lines Power Adaptor Supplied Main Line Additional Line Additional Line Additional Line Last Line Telephone System Controller FXO Port Alternative Used or Unused Line Trunk Input OR Installation when lock control is not required 6 YOUR PBX ACCESSORIES PARTNER

7 PBX Analog Extension or FXS Connection PBX Door Phone Intercom Solutions PBX Line Trunk or FXO connection Our DS4, DS5 and DS6 Model DOOR STATION controllers are designed to connect to an Analog extension, FXS or ATA Connection of a PBX system, which can be programmed to Hot Dial. You can then connect ONE of our range of surface mount or flush mount DOOR PHONES direct to the DOOR STATION controller. The door phones can be up to 330 yards (300 metres) from the door station controller. MODEL DS4 PBX Extension Connection No Lock Control When the call button of a door phone is activated, our DS4, DS5 or DS6 controller will generate an off hook condition to the extension, which will then Hot Dial the door phone call as programmed. Upon answer, communication is loud and clear, similar to a phone call and there are NO call charges, unless the call is routed to an external number. If the PBX cannot be programmed to Hot Dial, then you should use our Model DS6 which can dial a pre-programmed internal or external number when triggered by the door phone. MODEL DS5 PBX Extension Connection Single Lock Control The door station controller has a hang up tone detector that will then terminate the call as soon as the called party hangs up. Model DS5 incorporates an internal relay which can be used to open or release a door or gate lock. Lock release time is fully programmable. Model DS6 also provides two internal relays which can be used to open locks in two separate areas. The second relay in this model can alternatively be used to SWITCH ON a light, a video camera/recorder or any other electrical device as soon as the call button is pressed on the door phone and then SWITCH THEM OFF after the call is complete. MODEL DS6 PBX Extension or Trunk Connection Dual Lock Control Automatic Dialing Facility Power Supply Black Red Green Door Gate Lock (Not Supplied) Brown Yellow 12 Volt Out Orange 12 Volt In Installation when single lock control is required SUPPLYING QUALITY PRODUCTS SINCE 1990 TWO YEAR FACTORY WARRANTY 7

8 Message On Hold devices for any Business Telephone System DIGITAL MESSAGE ON HOLD PLAYERS We have been Manufacturing and Supporting Digital Message On Hold players since During these past 17+ years we have developed the World s Most Comprehensive Range of Message On Hold solutions. All of our models use MP3 technology and they use standard SD Cards or USB Sticks for storage of the MP3 file or files. Our Products incorporate the most comprehensive range of optional features available : Message Encryption Internet Message Update Intelligent Time Programmable Message Play After Hours Call Answer, Call Count and Message Play Internal Memory that is be loaded by SD Card or USB Stick Dual Channel Message On Hold and Background Music Message players We also offer the most extensive range of Single Line Solutions available & Standard Models For normal PBX use, we recommend use of our DMC or DMD Standard Models. They are compact, robust, easy to wall mount and built for Extreme Reliability. DMC Is our most popular Message On Hold player. It is supplied with an SD Card which conveniently inserts direct into a spring loaded slot at the back of the unit (or the top of the unit if wall mounted). The Complete SD card, except for just 1/8 of an inch is secured inside the player, so that it is protected from knocks that can happen in a PBX area. To remove the SD Card, you just push the card lightly and it will spring out. This player is manufactured in high volume and is very attractively priced. DMD DMD is identical to DMC in every way, except that it uses a Standard USB Stick to store its MP3 Message or Messages. The USB stick conveniently inserts direct into a USB slot at the back of the unit (or the top of the unit if wall mounted). A micro USB Stick is supplied with DMD. Wall Mounting Bracket DMC and DMD are housed in a Tough Plastic Enclosure which is designed for Flat or Wall Mount. It s injection moulded plastic base has 2 slots designed for Easy Wall Mounting using our Wall Mount Bracket which is supplied on request. 8 YOUR PBX ACCESSORIES PARTNER

9 SINCE 1990 DIGITAL MESSAGE ON HOLD PLAYER with Internet Message Update DME Is a highly reliable Message On Hold player that Receives Message Updates via the Internet. It also uses a Standard SD Card (supplied) to store it s Message or Messages so that it still provides for Easy Message Change by manually changing the SD card. This is important during times when Internet Access is disconnected, denied or unavailable. DME connects ANYWHERE on an Internet Connection. It can connect to ANY PC or Laptop connection point or even direct to the Broadband Modem or Switch/Router. DME uses DHCP technology to automatically connect to the Network and within seconds of first connection it makes an Outgoing Connection to a pre-programmed Internet destination (FTP Server). A preset User Name and Password protection ensure that DME will only update content that is intended for it. DME is completely Internet Safe as it makes Outgoing Connections Only. It is programmed to connect to one remote destination address only and any attempted Incoming connections cannot be answered. DME is perfect for sites that require Frequent Message Updates. DIGITAL MESSAGE ON HOLD PLAYER with After Hours Message Player and Call Counter DMS Is a highly reliable Message On Hold player that also has a Telephone Line Answering facility. This facility allows DMS to Answer After Hours telephone calls and then play a specific High Quality MP3 Message of Any Length to the Caller from Beginning to End. It can then either Hang Up (if Incoming Messages are not required) or it can Ring an attached Answering Machine so that callers can leave a Message. As well as having a standard 3.5mm Audio output for Message On Hold, DMS also connects to the Telephone Line in place of an Answering Machine, or where an Answering Machine is still required, it connects in series between the Answering Machine and the Telephone Line connection. Like an Answering Machine, DMS can be left in Answer On mode at all times, or the Answer function can be switched ON and OFF as required. DMS has a Digital Display that advises if the Answer Facility is ON or OFF. DMS uses a Standard SD Card (supplied) where the specific MP3 After Hours Message is saved along with the standard On Hold Message or Messages. DMS also has an After Hours Call Counter, so that the number of calls that are received after hours is displayed, regardless of whether they leave a Message. The Call Count can be quickly cleared when required. DMS is perfect for sites that require a Professional Quality After Hours Message or a Lengthy After Hours Message that cannot be provided by an Answering Machine or PBX memory. SUPPLYING QUALITY PRODUCTS SINCE 1990 TWO YEAR FACTORY WARRANTY 9

10 Automatic Announcement Device PBX Call Attendant / Call Announcer Our AAD Automatic Announcement Device is designed to answer incoming telephone calls and play a High Quality Message Announcement to callers. After playing a Message, ADD can then : Hang Up Re-Ring the Telephone Line so that you can take the call Hook Flash and allow the PBX to route the call to a pre programmed extension or group. ADD is ideal for applications such as: Providing telephone line information services Advising callers that their call may be recorded before their call is connected Advising callers of a new telephone number before their call is connected Providing after hours announcements and information Automatic Call Attendant for Multi-line telephone systems AAD incorporates our proven MP3 based Digital Message Centre technology, which provides for Message Announcements of exceptional quality and reliability. ADD uses an SD Card to store the Announcement Message, allowing for quick and easy Message change. Installation AAD can connect to a Single Telephone Line, a Line ahead of a PBX or an Analog Extension, ATA, FXS or FXO port. AAD provides Three operational modes : Mode 1 Mode 2 Mode 3 Play Message and then Hang Up Play Message and then Ring the attached Telephone Play Message, Hook Flash and then Hang Up Installation Diagrams AAD can be fitted to a standard telephone line PSTN Line 10 YOUR PBX ACCESSORIES PARTNER

11 SINCE 1990 AAD can be fitted direct to an Analog extension or FXS port Incomming Analog Telephone Lines 12V/1A Power Supply SD LIU Vol Card LINE IN LINE OUT 12V PABX System Controller Analog Extension or FXS Extensions AAD can be fitted direct to an incoming line of a PBX system Incomming Analog Telephone Lines 12V/1A Power Supply SD LIU Vol Card LINE IN LINE OUT 12V PABX System Controller The required line of the Phone System routes through AAD An AAD can be fitted to as many lines as required SUPPLYING QUALITY PRODUCTS SINCE 1990 TWO YEAR FACTORY WARRANTY 11

12 DTMF Controlled Relays RELAY CONTROL UNIT Intelligent DTMF Controlled Relay Units for Single Device Control or Access Control applications. It can be used on ANY of the following Telephone Lines : PSTN, Cable or Fiber Lines PBX Analog Extensions FXO Ports FXS Ports ATA Output Cellular Gateway Output A dedicated Access Control Line SINGLE UNIT OPERATION RCU will allow you to remotely control one or two electrical devices by dialing an Extension or Phone Number and entering a user set DTMF code. With RCU you can Open a Gate or Door, or with the correct Accessories you can Turn On or Off a Light, or Reset a PC or Server. MULTIPLE UNIT OPERATION You can also use Multiple RCU units together to control Multiple Devices or set up sophisticated Access Control applications. There are Two Models in the Range : RCU1 Has a Single Dry Contact Relay (rated at 1A) that can be programmed to respond to any 1-4 digit DTMF Code and which can be programmed to Toggle On/Off or Close for a period of seconds. RCU2 Has Two Dry Contact Relays (rated at 1A) each of which can be programmed with its own Code and Relay Closure time. 12 YOUR PBX ACCESSORIES PARTNER

13 SINCE 1990 APPLICATIONS 12V Power Supply A simple application would to connect an RCU1 to an Analog Extension and program the Relay1 to respond to the DTMF code 11. The closure time of the relay can then be set to 15 seconds. Then to Open an Electric Door, the user would just dial the extension number to which RCU1 is connected and then when RCU1 answers, they would press 11. The Door then Open for 15 seconds only. Electric Lock One leg of the power supply routes trough RCU Supplied Screw Terminal Adaptor Supplied 12VDC Adaptor A more complex application would to be to add another RCU to this same line, connected in parallel. In this example an additional RCU2 is used, which has 2 separate Relays, each which can have its own DTMF activation Code and Relay Closure time. Relay 1 has been programmed for DTMF 22 and its relay will close for 30 seconds. Relay 2 has been programmed for DTMF 33 and its relay is programmed to close for just 2 seconds, for a momentary closure. Power Supply 12VDC Dry Contact Closure Dry Contact Closure Parallel Line Connection Now a user can dial the same extension number, wait for RCU to Answer (all will answer) and then press 22 to allow access to a specific Elevator Floor (for up to 30 seconds) or press 33 to Open a Boom Gate. For even more Complex Applications, Multiple RCU s (any combinations of RCU1 s and RCU2 s) can be connected to the same Telephone Extension (or line) and every relay can be programmed with its own unique code and relay closure time. Then a user can call the extension number and either dial an individual relay code, or even enter a number sequence where several codes are dialled to command multiple relays to respond. For example pressing 12345, could control 5 separate relays, each controlling its own device or access. DTMF could be dialled to achieve the same result, as each RCU relay can be set to only look for its own unique code in a sequence. SUPPLYING QUALITY PRODUCTS SINCE 1990 TWO YEAR FACTORY WARRANTY 13

14 PBX PagingSwitch PA SWITCH PA Switch provides; Connection to a Public Address (PA) System from ANY PBX PA capability for IP based PBX systems PA capability for Cloud based PBX systems PA capability for Remote Sites Our PA Switches are designed to allow a Public Address (PA) system to be connected to an Analog extension of any PBX system, FXS, FXO or ATA port, so that Announcements can be made from ANY Telephone Extension at ANY time. Two Models There are 2 models in our range. Both are supplied with a High Quality Line Isolating Transformer. : Model PA1 Terminates the announcement after a fixed period of time or when the user presses any DTMF digit on their handset Model PA2 Terminates the announcement on detection of hang up tones, which occur as soon as the user hangs up PA2 is designed to detect standard Hang Up tones and will automatically hang up after detection of the 2nd tone PA2 can also hang up after a fixed period of time, or silence, or when the user presses any DTMF digit on their handset Easy Operation Once installed, PBX users need only call the Extension Number that PA Switch is connected to and they will be able to make their PA announcement. Installation Diagram Power Supply PA Amp PABX Extension Line Isolation Transformer (Supplied) LIU SYSTEM SOURCE 14 YOUR PBX ACCESSORIES PARTNER

15 SINCE 1990 INSTALLATION 1) Connect the Line In port of PA Switch to any Analog extension, FXS, FXO or ATA port, 2) Using the supplied RCA cable which has an integrated Line Isolation Transformer., connect the PA Amplifi er to the PA SYSTEM port of PA SWITCH 3) Connect the supplied 12V Power Pack 4) PA Switches are pre-programmed for common applications and are therefore plug and play A Programming port is provided on both PA Switches where a standard handset (or buttinski) can be connected This allows PA Switch to be programmed for rings before answer, maximum call time and in PA2, Busy Tone and Silence detection parameters, using normal touch tone keys PA Switch Accessories 1) Pre-Amp - Anti Pop Accessory 2) Push to Talk Accessory Pre Amp Anti Pop Accessory The Audio Output from some Telephone Systems may be too low for some Amplifiers, resulting in Low Paging Volume. Our Pre Amp Accessory provides amplification of the Telephone Line Audio to the Amplifier to overcome this problem. A Volume Pot is provided on the Pre Amp Accessory to allow the correct Paging Volume to be set. Some Amplifiers are not natively designed for a Telephone Line connection which can result in a Loud Pop on the Paging Speakers when a Telephone based Page is connected. Our Pre Amp Accessory is also designed to Automatically eliminate (or greatly reduce) any Pop that can result from an Amplifier used for Telephone Line paging. Push to Talk Accessory Some Amplifiers may require a Push To Talk (PTT) input. In this situation, you can connect our Off Hook Indicator (OHI) device to the same extension and connect the Relay Output from OHI to the PTT input. See page 21 for more details. SUPPLYING QUALITY PRODUCTS SINCE 1990 TWO YEAR FACTORY WARRANTY 15

16 PULSE to DTMF converter DECADIC to TONE DIALLER DTD is designed to allow a older Decadic (or Pulse) Dialing Telephone Device to operate with a Modern Fiber Telephone Line or IP Based Telephone Line. It can be used on ANY of the following Telephone Lines : PSTN, Cable or Fiber Lines PBX Analog Extensions FXO Ports FXS Ports ATA Output Cellular Gateway Output DECADIC to TONE DIALLER (DTD) connects BETWEEN the Decadic (Pulse) Dialing Telephone Device and the Telephone Line that it is connected to. DTD will then Automatically convert Decadic Pulse Dialed Digits to DTMF Touch Tones, so that the Telephone Device can Dial Out. Because DTD uses a 12V power supply for operation, its circuitry can operate with a unique, reliable and superior method of Decadic to Tone conversion. Dialing Operation When a Decadic Pulse Dialing Device goes Off Hook to dial, DTD provides an Interface that prevents any Decadic Pulses from passing through to the Telephone Exchange, which can causes issues. It instead reads the pulses and then at the completion of each pulse Dialed digit, it will transmit the appropriate DTMF digit to the Telephone Exchange or appropriate IP Interface. This method ensures that every Dialing event from an older Telephone Device is accurate and reliable. DTD will also operate with modern DTMF based Telephone devices. When one of these devices Dial s a Telephone Number, DTD will read and re-dial the same DTMF digits ensuring that every Dialing event is accurate and reliable. Incoming Call Operation Incoming calls pass through to the attached Telephone or Telephones without delay. Should Power be lost or disconnected from DTD, the attached Telephone Devices will be connected direct to the Telephone Line so that they can receive incoming calls and DTMF Dialing Telephone devices will be able to dial out. Installation 1. Connect the Line In port of DTD to ANY convenient position on the Telephone Line (cable provided). 2. Connect the Decadic/Pulse Dialing Telephone device direct to the Line Out port of DTD. 3. Connect the supplied 12V Power Pack. DTD can be powered by any 12VDC or 12VAC input with a min current capacity of 300mA. This allows for operation by a 12V Battery. 16 YOUR PBX ACCESSORIES PARTNER

17 Incoming Ring Booster RING BOOSTER When your Telephone Device will not Answer or when they Ring too Weakly, as can be the case with Modern Fiber Telephone lines. It can be used on ANY of the following Telephone Lines : PSTN, Cable or Fiber Lines PBX Analog Extensions FXO Ports FXS Ports ATA Output Cellular Gateway Output RING BOOSTER is designed to detect a small amount of Incoming Ring and transparently Output a Strong Ring to One or More attached Telephone Devices. RING BOOSTER is the Ideal solution for : Telephone Devices that currently will Not Answer Telephone Devices that Ring too Weakly or Will Not Ring at all Telephone Devices that Require UK Style Ring RING BOOSTER has a Dip Switch which allows the User to Select USA or UK style Ring Output. Installation 1. Connect the Line In port of RING BOOSTER to ANY of the above Telephone Line Sources 2. Connect the Problem Telephone devices to the Line Out port of RING BOOSTER 3. Connect the supplied 12V Power Pack. Incoming Call Operation Ring from any Incoming Call is detected by RING BOOSTER S sensitive Ring Detection Circuit. RING BOOSTER will then immediately Output Strong USA (or UK) style Ring to the attached Telephone Device(s). As soon as an attached Telephone Device Answer RING BOOSTER S ring, it will be immediately connected to the Incoming call so that it can communicate as required. Outgoing Call Operation RING BOOSTER will immediately Connect the attached Telephone Device(s) to the Telephone Line source as soon as they go Off Hook. General Operation RING BOOSTER is totally Transparent in Operation. In the event of Power Loss to RING BOOSTER, it will automatically connect the attached Telephone Device(s) to the Incoming Telephone Line so that it can make and receive calls. RING BOOSTER can be powered by any 12VDC or 12VAC input with a min current capacity of 300mA. This allows for operation by a 12V Battery. SUPPLYING QUALITY PRODUCTS SINCE 1990 TWO YEAR FACTORY WARRANTY 17

18 Two Line Switch TWO LINE SELECTOR Is designed to allow a Single Telephone Device to Connect to Two Telephones Line for Incoming and Outgoing calls. It can be used with ANY Combination of the following Telephone Lines : PSTN, Cable or Fiber Lines PBX Analog Extensions FXO Ports FXS Ports ATA Output Cellular Gateway Output With LINE SELECTOR a Telephone Device can : Dial Out on Two Lines Receive Calls on Two Lines Operation One of the Two attached lines is set as the DEFAULT LINE (LINE 1) and the other line is then set up as the ALTERNATIVE LINE (LINE 2). Both Incoming and Outgoing calls to/from the attached TELEPHONE DEVICE can take place on either line. Outgoing Calls from the TELEPHONE DEVICE can be made on either line. LINE SELECTOR will always choose the DEFAULT LINE (Line 1), unless it is busy in which case it will then use the alternative line (Line 2). Incoming Calls on EITHER LINE will be automatically routed to the attached device. Busy Out facility. If the attached device is already connected to a call, the other Line will be rendered Busy as well. This will prevent an Incoming Call not connecting to the attached Device. There are Two Models in the Range : LS1 Standard Version. Operates as above. This model is designed for Standard Applications where a Device needs to Automatically make an outgoing call and/or receive incoming calls from either line. LS2 Programmable Version. This model has a number of User programmable features that can be useful for some Two Line switching applications : Automatic Selection of Line 2 for Outgoing Calls can be disabled. Selecting Line 2 will require dialling of an Access Code first (*). Access Code can be changed from * to any other digit (0-9 or #) Line Change Delay can be changed from 1 second up to 9 seconds. The Other Line Busy Out Facility can be enabled or disabled separately for each line. Incoming Call Advice Facility. If your Device is on a Call, you can enable or disable a feature where a Call Advice tone can be injected into the call. When enabled, you can place your current call on hold to take a call on the other line and then return to the original call when finished. If Power to LINE SELECTOR is lost or disconnected, LINE SELECTOR will automatically connect the Telephone Device to LINE 1. Telephone calls can only be made or received on Line 1 until power is restored. LINE SELECTOR can be powered by any 12VDC or 12VAC input with a min current capacity of 300mA. This allows for operation by a 12V Battery. 18 YOUR PBX ACCESSORIES PARTNER

19 LINE SELECTOR CAN BE USED FOR MANY PBX AND OTHER APPLICATIONS Power Adaptor Supplied Incoming Telephone Lines Fixed Cellular Terminal Main Line Additional Line Additional Line Additional Line Additional Line Telephone System Controller Last Line INSTALLATION Line Selector will allow a 2nd line source, such as a Fixed Celullar Terminal (FCT) to be connected to a Line Trunk or FXO port. PBX users can then either use the normal line, or use the FCT by pressing * to select the FCT line. The PBX can also be set up to make least cost route calls via the FCT. Telephone Handsets Telephone Handsets Power Supply Alarm Panel Fire Alarm Panel Automatic Back Up Line Selection for Emergency Dialers Automatic Back Up Line Selection for Alarm Dialers SUPPLYING QUALITY PRODUCTS SINCE 1990 TWO YEAR FACTORY WARRANTY 19

20 Incoming Ring Indicator RING INDICATOR Advises PBX users, in NOISY environments, that there is an incoming call Easy Plug In Installation Simple, Cost Effective and Reliable Provides Relay Closure as soon as Incoming Ring is detected. It can be used on ANY of the following Telephone Lines : PSTN, Cable or Fiber Lines PBX Analog Extensions FXO Ports FXS Ports ATA Output Cellular Gateway Output Ring Indicator Switch has an internal relay which will Close on detection of ring and and Open when the ring ceases. The relay is rated at 12V/1A and can be used to directly control One of Two Accessories that have been designed to operate with Ring Indicator. Tone Alert (pictured) or Strobe Alert (see page 23), to provide one of the following Alerts : A Bright Red Flashing Strobe Light Alarm Speaker (with selectable Alarm Tones) and Volume Control A conne ction box with screw terminals that connects to the 4 pin RJ socket outlet of Ring Indicator is also supplied, should you with to connect a 3rd party device to the relay. INSTALLATION 20 YOUR PBX ACCESSORIES PARTNER

21 Off Hook Indicator OFF HOOK INDICATOR Is for use as a Line in Use Indicator or as a Line Left Off Hook Indicator. It can be used on ANY of the following Telephone Lines : PSTN, Cable or Fiber Lines PBX Analog Extensions FXO Ports FXS Ports ATA Output Cellular Gateway Output OFF HOOK INDICATOR (OHI) is designed to connect ANYWHERE on the Telephone Line Source that it is to be connected to. It can be connected in any Series or Parallel position on the line. In the Event that a Telephone Line (or simulated Telephone Line) goes Off Hook OHI will CLOSE an Internal Relay 5 seconds later and leave it CLOSED until the Line goes back On Hook. This allows OHI to be used as a Line In Use Indicator. Model OHI2 has a Delay Timer facility, allowing for up to 15 different Delay periods to be selected before OHI2 will CLOSE it s Internal Relay. This allows OHI to be used as a Line Left Off Hook Indicator. The Internal Relay is designed to connect to our Tone Alert or Strobe Alert Accessories (see page 23), to control one of the following Alerts: A Bright Red Flashing Strobe Light Alarm Speaker (with selectable Alarm Tones) and Volume Control The above accessories are powered direct from OHI and connect via a single 4 wire cable terminated with a 4 pin RJ plug (4P4C). A cable is supplied with each Accessory. A shorter or longer cable can be made to the required length, with Cat5 or Standard telephone cable being ideal. Polarity is not important as the Accessory has an Integrated Polarity Rectifier. For very long cable runs, the Accessory device can also be powered directly using a 12VAC or 12VDC source, (300mA min power adaptor - DC polarity does not matter) to ensure that the Strobe Light Intensity or Alarm Output Intensity can be maintained. Operation Should the Telephone Line that OHI is connected to be Disconnected or Cut, OHI will CLOSE its Internal Relay 5 seconds later (to Control an attached Accessory) and will REMAIN CLOSED until the Telephone Line is restored. Should the 12V power source to OHI be lost or disconnected, OHI s Internal Relay will remain Open (Normal Open Relay) and it will remain Open on reconnection of its 12V Power source. This means that OHI will not false trigger when power is lost or reconnected. SUPPLYING QUALITY PRODUCTS SINCE 1990 TWO YEAR FACTORY WARRANTY 21

22 Line Loss Indicator TELEPHONE LINE MONITOR Is designed to provide an ALERT whenever a Telephone Line (or Simulated IP Telephone Line) is Lost or Cut. It can be used on ANY of the following Telephone Lines : PSTN, Cable or Fiber Line PBX Analog Extensions FXO Ports FXS Ports ATA Output Cellular Gateway Output The Incoming Line should connect to the LINE IN port of TLM and all devices on the line should then connect to the LINE OUT port of TLM. In the Event that a Telephone Line (or simulated Telephone Line) is Lost or Cut, it will CLOSE an Internal Relay 5 seconds later and leave it CLOSED until the Line is reconnected or restored. The internal relay is designed to control One of Two Easy Connect Accessories that have been designed to operate with Ring Indicator. Tone Alert (pictured) or Strobe Alert (see page 23), to provide one of the following Alerts: A Bright Red Flashing Strobe Light Alarm Speaker (with selectable Alarm Tones) and Volume Control The above accessories are powered direct from TLM and connect via a single 4 wire cable terminated with a 4 pin RJ plug (4P4C). A 6ft cable is supplied with each Accessory. A shorter or longer cable can be made to the required length, with Cat5 or Standard telephone cable being ideal. Polarity is not important as the Accessory has an Integrated Polarity Rectifier. For very long cable runs, the Accessory device can also be powered directly using a 12VAC or 12VDC, (300mA min power adaptor - DC polarity does not matter) to ensure that the Strobe Light Intensity or Alarm Output Intensity can be maintained. 22 YOUR PBX ACCESSORIES PARTNER

23 Indicator Accessories Tone Alert Accessory Our Tone Alert Accessory outputs a Warning Tone as soon as it detects the Relay Closure output from one of the applicable Natcomm Products that it is connected to. It is usually used as a Plug In accessory for our Ring Indicator, Off Hook Indicator or Telephone Line Monitor Telephone Line Switches. Its output volume can be adjusted to suit any application : A volume pot provides for volume adjustment to suit open office areas up to 1000 sq ft, or small factory areas. An amplified 3.5mm Audio Output (7W) is also provided for connection of additional 8 Ohm Speakers or PC type Speakers with Amplifier and Volume Control, to suit larger Office Environments, Noisy Office Environments, or small-medium sized Factory Areas. The Audio Output can also be connected to an External Amplifier so that it s Alarm Tone can be used for ANY sized Office Environment or Factory Area serviced by a suitable Amplifier. Tone Alert uses an Internal Microprocessor circuit and Speaker to produce its 400hz tone. This is the same frequency as a Telephone Ring Tone, rather than the high pitched Alert Tone of inexpensive Piezo Alarms. It can output Warning Tone Cadences for different applications. A Continuous Tone A repeating Tone that is 2 Seconds On and then 2 Seconds Off A repeating Tone that is 4 Seconds On and then 4 Seconds Off A repeating Tone that is 2 Seconds On and then 4 Seconds Off (same as a Phone Ring) Strobe Alert Access The Strobe Alert Accessory uses EIGHT High Intensity RED LED s which Flash as soon as it detects a Relay Closure Output from the applicable Natcomm Product that it is connected to. When Wall Mounted, it is Ideal for a Small Open Office or Factory areas up to 1000 qs ft. For Larger areas, Two or More Strobe Alert Accessories can be connected in parallel. It can output Warning Tone Flashes for different applications. It can output. A Continuous Strobe Flash A Strobe Flash that is 2 Seconds On and then 2 Seconds Off A Strobe Flash that is 4 Seconds On and then 4 Seconds Off A Strobe Flash that is 2 Seconds On and then 4 Seconds Off (same as a Phone Ring) SUPPLYING QUALITY PRODUCTS SINCE 1990 TWO YEAR FACTORY WARRANTY 23

24 PBX Privacy Switch PRIVACY SWITCH To allow Two Devices or Systems to share a Telephone Line with Barge-In Protection. Privacy Switch is designed to allow a DIAL OUT only device to share a Telephone Line of a PBX, a normal PSTN Line or even an FXO, FXS or ATA output of an IP System. In the case of operation on a PBX, the shared line would normally be the Last Choice Line, but it can also be used on any PBX line. Incoming calls are directed to the NORMAL DEVICE destination without delay or answer. Outgoing calls can be made by both the NORMAL DEVICE and the ACCESSORY DEVICE. Privacy Switch is ideal for connection of a Non Emergency Telephone Device : A Dial Out only Modem Device such as a Vending Machine, Electronic Till or Time Clock A Pay Phone Any other Dial Out only device Barge-In protection ensures that the PBX or Normal Device and also the Accessory device, cannot be interrupted by the other device, when they are using the Telephone Line. Installation For a PBX Line, PSTN Line or FXO, FXS, ATA output of an IP System 1. Connect the appropriate Telephone Line Input to the Line In port of Privacy Switch 2. Connect the Normal Device port of Privacy Switch to the PBX Trunk Input, FXO Port or Direct to the Normal Device itself. 3. Connect the Accessory device to the Accessory Device port of Privacy Switch 4. Connect the supplied 12V Power Pack See Installation options on page xx Operation 1. Incoming calls connect to the PBX or Normal Device as normal, without delay or answer 2. Outgoing Telephones calls can be made by either the Normal Device or Priority device 3. Barge-In protection ensures only one device can connect to the line at one Should power to the Privacy Switch ever be lost or disconnected, Privacy Switch will connect the Normal Priority Device to the Telephone Line. The Accessory Device will not be able to access the Telephone line. 24 YOUR PBX ACCESSORIES PARTNER

25 PBX Priority Switch PRIORITY SWITCH For Emergency Dialing Devices which share a Telephone Line. PRIORITY SWITCH is designed to allow a PRIORITY DIAL OUT DEVICE to share a Telephone Line of a PBX, a normal PSTN Line or even an FXO, FXS or ATA output of an IP System. In the case of operation on a PBX, the shared line would normally be the Last Choice Line, but it can be used on any PBX line. Incoming calls are directed to the NORMAL DEVICE without delay or answer. Outgoing calls can be made by both the NORMAL DEVICE and the PRIORITY DEVICE. PRIORITY SWITCH is very similar to our Privacy Switch, EXCEPT THAT with PRIORITY SWITCH the Accessory device is always given Priority Access to the Line. 1. If the Line was in use by the Normal Device when the Priority Device goes Off Hook to make an Emergency Call, Priority Switch will automatically terminate the Normal Device call so that the Telephone Exchange (or Analog IP device) will clear down and then allow after a short delay connect the Priority Device to the Line. 2. Should power to the Priority Switch ever be lost or disconnected, Privacy Switch will connect the Priority Device to the Telephone Line. The Normal Device will not be able to access the Telephone line. Our Barge-In protection facility will prevent the Normal Device from interrupting the Line during a Priority Device call. Priority Switch is ideal for connection of an EMERGENCY DEVICE, such as: An Emergency Phone An Alarm System An Elevator Phone An Emergency Dial Out Device Installation For a PBX Line, PSTN Line or FXO, FXS, ATA output of an IP System 1. Connect the appropriate Telephone Line Input to the Line In port of Priority Switch 2. Connect the Normal Device port of Priority Switch to the PBX Trunk Input, FXO Port or Direct to the Normal Device itself. 3. Connect the Priority device to the Priority Device port of Priority Switch 4. Connect the supplied 12V Power Pack See Installation options on page xx Operation 1. Incoming calls connect to the PBX or Normal Device as normal, without delay or answer 2. Outgoing Telephones calls can be made by either the Normal Device or Priority device 3. Barge-In protection ensures only one device can connect to the line at one 4. If the Normal Device is using the Line when the Priority Device goes Off Hook to access the line, the Normal Device will be disconnected immediately and the Priority Device will be connected to the line after a short delay to allow the Telephone Exchange or IP Device to clear down. SUPPLYING QUALITY PRODUCTS SINCE 1990 TWO YEAR FACTORY WARRANTY 25

26 PBX Eftpos Switch RING DELAY SWITCH Delays incoming call connection to an attached device for 1-15 rings Re-Routes incoming calls to another Line after 1-15 rings Stops Devices Answering Too Early Applications Ring Delay Switch is ideal for connection of Unanswered Incoming Calls to a: Alarm System Call Diverter Answering Machine Announcement Device Alternative PBX Line Alternative IP Line Device Alternative Cellular Line Device Operation Ring Delay Switch is designed to allow an Accessory device to be connected to a Telephone Call after a User Set Delay of 1-15 Rings, if the call is not answered by the Normal Device. Alternatively, it can connect an Incoming Call to an Alternative Line Source after a set number of Unanswered Rings. Ring Delay Switch can share a normal PSTN Line, Incoming PBX Line, Analog Extension of a PBX, or even an FXO, FXS or ATA output of an IP System. In the case of operation on a PBX, the shared line would normally be the Last Choice Line, but it can be used on any PBX line. INCOMING CALLS Incoming calls are directed to the NORMAL DEVICE without delay or answer. If the Normal Device does not Answer the Incoming Call by the user set number of rings (set by a dip switch), then Ring Delay Switch will then Switch the Incoming Call to the Device connected to the Ring Delay port, so that it can connect a call to another line, ring alternative Telephones or allow an attached device to Answer. OUTGOING CALLS Outgoing calls can be made by both the Normal Device and the Ring Delay Device. Barge-In protection ensures that the PBX, Normal Device and also the Ring Delay device, cannot be interrupted by the other device, when they are using the Telephone Line. Installation Diagram Suplay 12VDC Power Adaptor Primary Device Ring Dealy Device PSTN line, PBX Extension, FXS or ATA IP Port 26 YOUR PBX ACCESSORIES PARTNER

27 Ring Delay Switch EFT-POS SWITCH EFT-POS Switch operates in the same way as PRIVACY SWITCH, with the exception that it provides full Telephone Line Voltage to the EFT-POS at all times, which is a requirement of EFT-POS Devices Incoming calls are directed to the normal destination, without delay or answer Outgoing calls can be made by both the PBX and the Eftpos Device Barge-In protection ensures that the PBX or Eftpos, when connected to the Telephone Line, cannot be interrupted by the other device Installation Diagram Installation 1. Connect the Last Choice telephone line to the Line In port of Eftpos Switc 2. Connect the Line Out port of Eftpos Switch to the PBX Trunk Input 3. Connect the EFT-POS device to the EFT- POS Device port of Eftpos Switch 4. Connect the supplied 12V Power Pack Operation 1. Incoming calls connect to PBX as normal, without delay or answer 2. Outgoing Telephones calls can be made by either the PBX or Eftpos device 3. Barge-In protection ensures only one device can connect to the line at one time Main Line Additional Line Additional Line Additional Line Telephone System Controller Eftpos Device Incoming Telephone Lines Additional Line Last Line Power Adaptor Supplied Telephone Handsets SUPPLYING QUALITY PRODUCTS SINCE 1990 TWO YEAR FACTORY WARRANTY 27

28 PBX FaxSwitch FAXSWITCH For most businesses, there is no longer any need for an expensive Dedicated Fax Line. Fax Use is decreasing due to the increased use of Telephone Line Rentals continue to increase Telephone Line Installation Charges continue to increase With FaxSwitch you can : Move your Fax Line to your PBX Rotary Group to add an additional line Cancel the existing Last Choice Line and replace it with the Fax Line FaxSwitch is specifically designed to allow a Fax Machine to Share the Last Choice line of a PBX Rotary Group (PSTN Lines only). It provides Completely Automatic Fax Reception, with 100% detection accuracy and reliability. There is no need to change the Fax Number, as the Fax Line is now the Last Choice line. Save over $$$ s per year in unnecessary line rental alone. Save even more if a new line installation is involved. Installation Connect the incoming Last Choice telephone line to the Line In port of FaxSwitch 2 Connect the Line Out port of FaxSwitch 2 to the PBX Trunk Input used for the Last Choice telephone line Connect the Fax Machine to the Fax Device port of FaxSwitch 2. Leave the Fax Machine settings unchanged Connect the supplied 12V Power Pack and installation is complete Operation The only time a call will ring on the Last Choice line is when: 1) It is a Fax Call 2) It is a Telephone call, but ONLY if ALL other lines in the Rotary Group are in use FaxSwitch will answer all incoming calls on this line BEFORE the call rings on the PBX. It will then listen for a Fax Calling Tone. If the Calling Tone is detected, it will ring the Fax Machine so that it answers and then connect the Fax call to it so that it will receive the Fax transmission. On the rare occasions that the incoming call is a Voice call, FaxSwitch 2 will ring the PBX system as normal, after a 4 second listening delay. 28 YOUR PBX ACCESSORIES PARTNER

29 Installation Diagram Power Adaptor Supplied Incoming Telephone Lines Fax Machine Main Line Additional Line Additional Line Additional Line Additional Line Last Line Telephone System Controller INSTALLATION Fit Fax Switch to the existing LAST LINE of the PHONE SYSTEM or move the Fax Line into the rotary group, to add an additional Voice Line. You still keep the existing Fax Number. Telephone Handsets Telephone Handsets MODEM SWITCH Some businesses require the ability to DIAL IN to a Modem based device, such as an Air Conditioner, Alarm System, Retail Cash Register, Vending Machine or ANY other device which has an Analog modem. The need to DIAL IN is usually infrequent and the cost of using a dedicated telephone line is cost prohibitive and totally unnecessary. Modem Switch operates in the same way as FaxSwitch, except that it is programmed to detect a Modem Calling Tone instead of a Fax Calling Tone. When used on a PBX, Modem Switch connects in the same manner as the FaxSwitch and the dial in Modem Number is simply the telephone number assigned to the Last Choice Line. Modem Switch can also be used on a Fax Line, EFT-POS line or any other available telephone line. The normal use of the line remains unaffected. SUPPLYING QUALITY PRODUCTS SINCE 1990 TWO YEAR FACTORY WARRANTY 29

30 Innovative Accessories for ANY PBX (PSTN, ISDN, IP or Cloud) BUDGET INTERCOM PREMIUM INTERCOM SIN WITH INTEGRATED CCD COLOR CAMERA CE 1990 INTEGRATED PEDESTRIAN ACCESS KEYPAD. PAGES 4-5 PAGES 4-5 PAGES 4-5 PAGES 4-5 PBX TRUNK CONNECTION (OR FXO) PBX EXTENSION CONNECTION (OR FXS, ATA) PROGRAMMABLE LOCK CONTROL SINGLE OR DUAL DIAL OUT INTERCOM OPERATION PAGE 6 PAGE 7 PAGE 7 PAGE 7 DIGITAL MESSAGE ON HOLD ON HOLD & AFTER HOURS MESSAGE CALL ATTENDANT ANNOUNCEMENT PLAYER PAGING SWITCH ANALOG AND SIP MODELS PAGES 8-9 PAGE 10 PAGE 11 PAGES DIAL IN RELAY & ACCESS CONTROL DECADIC to TONE DIALER RING BOOSTER AUTOMATIC TWO LINE SWITCH PAGES PAGE 16 PAGE 17 PAGE INCOMING RING INDICATOR ANALOG AND SIP MODELS OFF HOOK INDICATOR TELEPHONE LINE MONITOR STROBE & SPEAKER ALERT ACCESSORIES PAGE 20 PAGE 21 PAGE 22 PAGES 23 PRIORITY SWITCH PRIVACY SWITCH RING DELAY SWITCH EFT-POS SWITCH PBX FAX SWITCH PAGE PAGE 26 PAGE 27 PAGES NATCOMM USA QUALITY AND INNOVATION Phone info@natcomm.us Web