JPexam. 最新の IT 認定試験資料のプロバイダ IT 認証であなたのキャリアを進めます

Size: px

Start display at page:

Download "JPexam. 最新の IT 認定試験資料のプロバイダ IT 認証であなたのキャリアを進めます"

Sandra West
5 years ago
Views:

1 JPexam 最新の IT 認定試験資料のプロバイダ IT 認証であなたのキャリアを進めます

2 Exam : Title : Troubleshooting Cisco Data Center Infrastructure Vendor : Cisco Version : DEMO Get Latest & Valid Exam's Question and Answers 1 from Jpexam.com. 1

3 NO.1 On the secondary vpc switch, under which circumstance does the vpc autorecovery feature not bring up the vpc member ports? A. Peer link fails, and subsequently, the peer-keepalive link fails. B. Both vpc peers are reloaded, and the primary does not come back up. C. Peer link fails, and subsequently, the primary switch fails. D. Peer link is up, and the peer-keepalive link fails. Answer: D NO.2 Which command output shows the interface assigned as the designated receiver of each VLAN? A. show platform software enm internal info vlandb all B. show system vlan reserved C. show vlan internal bd-info bd-to-vlan all-bd D. show port internal info all Answer: A NO.3 Which two of these would cause two switch fabrics not to merge? (Choose three.) A. The switches do not have at least one assigned domain ID in common. B. The election of the static domain is only determined by the WWNs of the two switches. C. The static domain ID does not override the dynamic I D. The switches have different assigned VLANs on the connecting ports. E. Two switches have different assigned VSANs on the connecting ports. Answer: D,E Explanation s NO.4 The external routes are unreachable from the fabric in a Cisco ACI environment. What should you do? A. Configure BGP confederation. B. Enable MP-BGP in the fabric. C. Configure BGP for IPv6 D. Apply the BGP policy map to the interface. Answer: B NO.5 Which identification for EPGs can you use to check zone rules? A. VLAN B. PcTag C. VXAN D. EPG name Answer: B NO.6 Refer to the exhibit. Get Latest & Valid Exam's Question and Answers 2 from Jpexam.com. 2

No OSPF neighborship exists between N5K-1 and N7K-1. Which configuration resolves this issue? A. (config)# router ospf 1 (config-router)# network 192.168.103.152 255.255.255.252 area 0 B.

4 No OSPF neighborship exists between N5K-1 and N7K-1. Which configuration resolves this issue? A. (config)# router ospf 1 (config-router)# network area 0 B. (config)# router ospf 1 (config-router)# network area 0 C. (config-rf)# ip router ospf 1 area 0 D. (config)# ip router ospf 1 area 0 Answer: A NO.7 Which statement is true about the show cfs merge status name command? A. In a successful merge, all switches in the fabric are shown separately. B. The command shows the complete Cisco Fabric Services region database. C. In a successful merge, all switches are shown in a local fabric. D. The merge master is selected based on the highest swwn in the fabric. NO.8 Which two options are Cisco UCS default user roles? (Choose Two) A. Server Equipment Administrator B. Server Resource Administrator C. FCoE Administrator D. Administrator E. LAN Administrator Answer: A,D NO.9 Refer to the exhibit. Get Latest & Valid Exam's Question and Answers 3 from Jpexam.com. 3

Your customer is migrating their existing top-of-rack data center to a new location that uses an endof-rack configuration. The customer requests a site survey prior to the migration.

5 Your customer is migrating their existing top-of-rack data center to a new location that uses an endof-rack configuration. The customer requests a site survey prior to the migration. Which fact must you highlight in your survey that is required for a successful translation? A. power source must be 240 volts only for fabric interconnect switches. B. power source must be 240 volts only for blade chassis. C. blade chassis using passive TWNAX cables must be placed within 5 meters of the end rack. D. Blade chassis must not be fully equipped with blades when using and end-of-racksetup. NO.10 Refer to the exhibit. Get Latest & Valid Exam's Question and Answers 4 from Jpexam.com. 4

You connect Cisco Nexus 5600 Series switches to Cisco Nexus 2200 Series Fabric Extenders by using FET-10G SFPs. Which command resolves the error that is shown in the exhibit? A.

6 You connect Cisco Nexus 5600 Series switches to Cisco Nexus 2200 Series Fabric Extenders by using FET-10G SFPs. Which command resolves the error that is shown in the exhibit? A. switch#(config-if)# switchport mode fex-fabric B. switch#(config-if)# switchport mode dynamic desirable C. switch#(config-if)# switchport mode dotlq tunnel trunk D. switch#(config-if)# switchport mode fabricpath Answer: A NO.11 You have three VDCs named VDCI, VDC2 and VDC3 connected to the same environment, Due to a network device malfunction, there is an ARP storm in VDC1 Users in VDC2 discover that ARP is not resolving in VDC1. What is causing the issue? A. The CoPP settings for VDC2 are incorrect, B. VDC1 is responsible for processing ARP for all of the VDCs, C. The committed information rate is exceeded. D. The CoPP settings for VDC1 are Incorrect. NO.12 A customer has a Cisco UCS Center cluster. The customer configures LDAP as the AAA protocol and enables SSL for LDAP. The LDAP authentication fails. Which issue is the cause of the failure? A. The LDAP client passed an incorrect from the trustpoint. B. The CA certificate is missing from the trustpoints. C. The LDAP time limit that is specified by either the client or the server was exceeded. D. The LDAP server limit that is set by an administrative authority was exceeded. NO.13 A customer is troubleshooting FCoE in its network and sees pause counters increasing when it runs the command show interface eth1/5. What is the cause of this? A. The HBA connected to the switch is sending Xon or Xoff PFC frames. B. A firmware upgrade on the Fibre Channel adapter that is connected to the switch will fix this issue. C. The CNA connected to the switch is sending Xon or Xoff PFC frames. D. Pause counters increase regularly; there is nothing to be concerned about. NO.14 Refer to the exhibit. Which link is down? Get Latest & Valid Exam's Question and Answers 5 from Jpexam.com. 5

7 A. Link3 B. Link4 C. Link1 D. Link2 Answer: D NO.15 You are troubleshooting a Cisco Nexus 1000V Series Switch. Which command can you use to Get Latest & Valid Exam's Question and Answers 6 from Jpexam.com. 6

8 re-establish communication between VSM and VMware vcenter? A. setup B. reload C. reset D. connect Answer: D Get Latest & Valid Exam's Question and Answers 7 from Jpexam.com. 7

JPexam. 最新の IT 認定試験資料のプロバイダ IT 認証であなたのキャリアを進めます

JPexam. 最新の IT 認定試験資料のプロバイダ IT 認証であなたのキャリアを進めます JPexam 最新の IT 認定試験資料のプロバイダ http://www.jpexam.com IT 認証であなたのキャリアを進めます Exam : MB6-704 Title : Microsoft Dynamics AX 2012 R3 CU8 Development Introduction Vendor : Microsoft Version : DEMO Get Latest & Valid