10G SDH/OTN/Ethernet Test Module

Transcription

1 OTM2502/2512 OTM2502 (not support OTN) and OTM G multi service test modules are the comprehensive test solution provided by OPWILL, for 1.5M to 10G full rate PDH, SDH, OTN, and IP RAN/PTN network test. It specialised for mobile backhaul network performance measurement. OTM2502 can be upgraded to OTM2512. This module is compatible with OTP6200v2 (OPWILL Intelligent Network Test Platform). All-in-one test instruments support with OTN, SDH, SONET, PDH, DSn, MPLS-TP and Ethernet; Ethernet testing up to 10Gbps including RFC2544, RFC3393, and Y.1564; MPLS-TP up to 10Gbps. OPWILL TECHNOLOGIES (BEIJING) CO., LTD.

2 Platform Briefs: OTP6200 Compact and lightweight designed; Graphical user interface, easy to operate; 6.5inches outdoor-enhanced LCD colour touch screen; Ultra-high capacity field-exchangeable Li-ion battery pack extends testing time; Powerful modular intelligent network test platform; Dial, number keys and function keys for flexible scrolling and selecting; Remote control by PC using 10/100M Base- T port. Modules Briefs: OTM2502 and OTM G SDH 10G OTN 1G Ethernet 10G Ethernet OTM2502 (Can be upgraded to 2512) (Optional) (Optional) OTM2512 (Optional) (Optional)

3 Key Feature: OTN: Complies ITU-T G.709, and G.sup43; OTU1, OTU2, OTU1e, and OTU2e interfaces; Synchronous/asynchronous mapping of SDH/SONET signals; OTU, ODU, OPU error injection and alarm generation; OTU, ODU, OPU bytes control and decode; APS Time measurement. SDH/SONET: STM-1/STM-4/STM-16/STM-64, and OC- 3/OC-12/OC-48/OC-192 interfaces; Mapping/de-mapping of payloads from VC4-64c/STS-192c down to VC11/VC12, and VC1.5/VT2; SDH/SONET overhead control and decode; Pointer monitoring and adjustment, G.783 pointer test sequences generation; APS time measurement. PDH/DSn: DS1/DS3, E1/E3/E4 interfaces; APS time measurement; Error performance analysis per ITU-T G.821, G.826, and M Ethernet: 10/100/1000M Base-T, 100M-FX, 1000M Base-X, 10G Base-X interfaces; Generate up to 16 traffic flows with different MAC address, VLAN tags, MPLS, IP address, TCP/UDP, payload and bandwidth; MPLS-TP test up to 10G; Throughput, latency, frame loss, and backto-back measurements per RFC2544; Network configuration test and performance test per standard ITU-T Y.1564; Service disruption test.

4 Applications: Out-of-Service Test: End-to-end error free transmission verification; Automatic protection switching verification; SDH/SONET mapping verification down to VC12/VT1.5. Round Trip Delay: In-Service Test: Through mode; In-service monitoring protected monitoring points or optical splitters; Overhead bytes monitoring and decoding; Pointer monitoring. Carrier Ethernet Installation and Troubleshooting: Ethernet traffic generation up to 10G; Metro/Carrier test up to 10G including RFC2544, Y.1654; MPLS-TP test up to 10G; Packet capture for advanced troubleshooting.

5 General Specifications: OTP OTM2502/OTM2512 GENERAL SPECIFICATIONS User Interface Screen 6.5 Inch TFT Touch Screen (640 x 480); Other Interface USB Ethernet Audio Storage 8G; Physical Specifications Temperature Relative Humidity USB2.0, A type, 2; USB2.0 Mini B type, 1; Ethernet 10/100, RJ45; 3.5mm Audio Interface; Operating: -10 C to 50 C; Storage:- 40 C to 70 C; 0% to 95% (non-condensing); Size(H W D) Weight Vibrancy Mechanical Shock EMC OTP6200: 319mm x 202mm x 105mm; OTM2502/2512: 50mm x 97mm x 259mm; OTP6200: 2.8kg; OTM2502/2512: 0.8kg; 10Hz to 500Hz < 1.5g (on 3 main axes); 6 sides, 8 edges < 760cm, according to GR-196-CORE; EN55022/CIPSR22, EN , EN55024; Battery and Power Supply Battery Rechargeable Li-lon batteries; Working time: 3 hours to 12 hours(under different test conditions); Charging time: 6 hours (typical: 25 C); Power Source Input: VAC, 50-60Hz, 2A; Output: 19VDC, 4A.

6 OTN OTN Test Port Technical Specifications: OTM2502/OTM2512 OTU2, OTU1e, OTU2e optical interface: XFP, 1 port; User selectable optical module: 1310nm, 1550nm. OTU1 optical interface: SFP, 1 port; User selectable optical module: 1310nm, 1550nm. Measurement Out-of-service Mode; In-service Mode; Operation Frame and Scramble Transmitter Clock Receive Single Rate TCM Frame Format OTN Mappings Pointer-to-pointer Mode; Through mode; Enhanced through mode; The OTU, ODU and OPU overhead can be changed; and the FEC encoder and decoder can be set ON/OFF in any mode. In accordance with ITU-T G.709 and G.sup43; Internal clock: Accuracy: 4.6ppm, up to 2ppm; Clock Offset: ±100ppm (1ppm steps); Recovered clock; TTL level external 2.048MHz clock; E1: 2.048Mbps; DS1: 1.544Mbps; ±100ppm; Frequency deviation indication resolution: ±1ppm; ITU-T G.783, G.707 Annex D and Annex E, POH bytes: HP-N1 (SDH); LP-N1 (SDH); LP-N2 (SDH); Z5 (SONET); Z6 (SONET); TCM access point identifier (Apid): 15 bytes ASCII sequence, CRC-7; OTN Alarm Alarm can to be detected: OTU: OTU-AIS, LOF, OOF, LOM, OOM, SM-TIM, SM-BIAE, SM-BDI, SM-IAE; ODU: ODU-AIS, ODU-OCI, ODU-LCK, PM-TIM, PM-BDI; ODU Multiplex: ODU-LOF, ODU-OOF, ODU-LOM, ODU-OOM; OPU: PLM, OPU-MSIM, CSF, LSS; TCM: TCMi-TIM, TCMi-BIAE, TCMi-BDI, TCMi-IAE (i=1-6); TCM: TCMi-TIM, TCMi-BIAE, TCMi-BDI, TCMi-IAE (i=1-6); Alarm can to be generated: OTU: OTU-AIS, LOF, OOF, LOM, OOM, SM-TIM, SM-BIAE, SM-BDI, SM-IAE; ODU: ODU-AIS, ODU-OCI, ODU-LCK, PM-TIM, PM-BDI; ODU Multiplex: ODU-LOF, ODU-OOF, ODU-LOM, ODU-OOM; OPU: LSS, CSF; TCM: TCMi-TIM, TCMi-BIAE, TCMi-BDI, TCMi-IAE (i=1-6); Alarm generation mode: Continuous; Alternate; Burst;

7 OTN Test OTN Error Mapping Adjustment BERT Pattern FEC Overhead OTN Result Status Statistics Histogram APS Propagation Delay Measurement Error to be detected: OTU: FAS, MFAS, SM-BEI, SM-BIP8, FEC- Correctable, FEC-Uncorrectable; ODU: PM-BIP8, PM-BEI; Error to be generated: OTU: FAS, MFAS, SM-BEI, SM-BIP8; ODU: PM-BIP8, PM-BEI, ODU-FAS; OPU: BIT; TCM: TCMi-BEI, TCMi-BIP8 (i=1-6); OPU: BIT; TCM: TCMi-BEI, TCMi-BIP8 (i=1-6); Error generation mode: Continuous; Alternate; Burst; Single; N-frame; Rate; Adjustment: (each AMP): -1/+1/+2; Cm (t) (each GMP): based on Cm (t) (ppm); Pattern generation and monitor for O.181 bulk test pattern; Support to generate and detect: PRBS9, PRBS11, PRBS15, PRBS20, PRBS23, PRBS31; Support reversed PRBS pattern: 16bit user define pattern; ITU-T O.182; Generation of OTU, ODU, OPU overhead bytes; Display of current OTU, ODU, OPU overhead bytes; All overhead can be decoded; Just All overhead and anyone overhead PRBS BER (Including with GCC) testing; 256 frames overhead capture and decode; Display information of current status: Alarms and errors; Input power of optical signal; Event log display: Alarms (seconds) Errors (count and rate); Pointer operations; Frequency; Frequency deviation; All alarms and errors detected can be display in histogram; Start/stop time; All events refresh with 1 second resolution; APS (Automatic Protection Switching): APS time; Independently select start and complete trigger; Select trigger from advanced OUT to ODU; Display and save APS time, frequency, pass/fail, minimum/maximum/ average value; APS time resolution: 0.1ms; Resolution: 0.1us; Measurement max time: 5.0 s.

8 SDH and SONET SDH and SONET Test Port STM-64/OC-192 optical interface: XFP, 1 port; User selectable optical module: 1310nm, 1550nm STM-16/STM-4/STM-1, OC-48/OC-12/OC-3 optical interface: SFP, 1 port; User selectable optical module: 1310nm, 1550nm STM-1e, STS-3 electrical interface: BNC, 1 port; Measurement Out-of-service mode; In-service mode; Operation Frame and Scramble Line Code Transmitter Clock Receive Single Rate TCM Frame Format SDH Mapping Through mode; Pointer-to-pointer mode; Enhance through mode; Can be changed SOH/TOH, can injection alarms and errors under Enhance Through Mode. SDH: complies with latest version ITU-T G.707; SONET: complies with latest version Telcordia GR-253; NRZ; Internal cock: Accuracy:4.6ppm; Clock offset: ±100ppm (1ppm steps); Recovered clock; TTL level external 2.048MHz clock; E1: 2.048Mbps; DS1: 1.544Mbps; ±100ppm; Frequency deviation indication resolution: ±1ppm; ITU-T G.783, G.707 Annex D and Annex E, POH bytes: HP-N1 (SDH); LP-N1 (SDH); LP-N2 (SDH); Z5 (SONET); Z6 (SONET); TCM access point identifier (Apid): 15 bytes ASCII sequence, CRC-7; SONET Mapping

9 SDH and SONET Test Alarm Error BERT Pattern Pointer Overhead SDH Tributary Scan SONET Tributary Scan Smart Scan SDH and SONET Result Status Statistics Histogram Error Performance Alarm can to be detected and generated: SDH: LOS, LOF, OOF, MS-AIS, MS-RDI, AU-AIS, AU-LOP, HP-PLM, HP-UNEQ, HP-TIM, HP- RDI, TU-LOM, TU-AIS, TU-LOP, LP-PLM, LP-UNEQ, LP-TIM, LP-RDI, LP-RFI, LSS; SONET: LOS, LOF, OOF, AIS-L, RDI-L, AIS-P, LOP-P, TIM-P, PLM-P, UNEQ-P, RDI-P, LOM-V, AIS-V, LOP-V, PLM-V, UNEQ-V, RDI-V, TIM-V, LSS; TCM: TC-LTC, TC-TIM, TC-UNEQ, TC-AIS, TC-RDI, TC-ODI; Alarm generation mode: Continuous; Alternate; Burst; Error can be detected and generated: SDH: FAS, B1, B2, MS-REI, HP-B3, HP-REI, LP-B3, LP-BIP2, LP-REI, Bit Error; SONET: FAS, B1, B2, REI-L, B3, REI-P, B3-V, BIP2-V, REI-V, Bit Error; TCM: TC-IEC, TC-BIP2, TC-REI, TC-OEI; Error generation mode: Single; Continuous; Alternate; Burst; Rate; N-frame; Pattern generation and monitor for O.181 bulk test pattern; Support to generate and detect: PRBS9, PRBS11, PRBS15, PRBS20, PRBS23, PRBS31; Support reversed PRBS pattern: 16bit user define pattern; Support AU/TU, STS/VT pointer monitor and generation; Support ITU-T G.783 pointer test sequences; Display pointer value of receiver side; Generation of section/transport and path overhead bytes; Display of current section/transport and path overhead bytes; All overhead can be decoded, including decoded J0,J1,J2 byte; All overhead and anyone overhead PRBS BER testing; Just all overhead and anyone overhead PRBS BER(Including with DCC) testing; 256 frames overhead capture and decode; DS1 embedded in selected VC-11; E1 embedded in selected VC-12; DS1 embedded in selected VT-1.5; E1 embedded in selected VT-2; Remote single auto detects and auto setup for SDH analyser; Display information of current status: Alarms and errors; Input power of optical signal; Event log display: Alarms (seconds); Errors (count and rate); Pointer operations; E3/DS3 embedded in selected VC-3; E4 embedded in selected VC-4; E3/DS3 embedded in selected STS-1; E4 embedded in selected STS-3c; Actual bit rate; Frequency ; Frequency deviation. Start/stop time; All events refresh with 1 second resolution; All alarms and errors detected can be display in histogram, user can see all issues directly; G.821/G.826/G.828/G.829/M.2100/M/2101 analysis of received signals based on detected errors and alarms: ES,SES,BBE,AS,UAS and so on;

10 SDH and SONET Result APS Propagation Delay Measurement APS (automatic protection switching): Independently select start and complete trigger; All SDH/SONET alarms and errors, bit error, errors with threshold; Number of switchovers indicated by APS protocol; K1/K2 bytes set and displayed; Display and save APS time, frequency, pass/fail, minimum/maximum/ average value. APS time resolution: 1us; Resolution: 0.1us; Measurement max time: 2.0 s. PDH and DSn PDH and DSn Test Port PDH: E1, E3, E4; 1 Port; DSn: DS1, DS3; 1 Port; Measurement Out-of-service mode; In-service mode; General E1: complies with latest version ITU-T G.703 for 2048kbps; DS1: complies with latest version ANSI T1.102 for 1544kbps; E3: complies with latest version ITU-T G.703 for 34368kbps; DS3: complies with latest version ANSI for 44736kbps; E4: complies with latest version ITU-T G.703 for kbps; Impedance E1: 75Ω(unbalanced); E3: 75 Ω; DS3: 75 Ω; E4: 75 Ω; Line Code E1: HDB3, AMI; DS1: B8ZS, AMI; E3: HDB3; DS3: B3ZS; E4: CMI; Frame Transmitter Clock Receive Single Rate Impedance Mode Alarm Error E1: unframed, PCM30, PCM31, PCM30CRC, PCM31CRC; DS1: unframed, SF-D4, ESF; Internal clock: Accuracy: 4.6ppm; Clock offset: ±100ppm (1ppm steps); Recovered clock; ±100ppm; Frequency deviation indication resolution: ±1ppm; E1: terminate, monitor; DS1: terminate, Monitor; E3: terminate, monitor; E3: unframed, framed (G.751); DS3: unframed, framed; E4: unframed, framed (G.751); TTL level external 2.048MHz clock; E1: 2.048Mbps; DS1: 1.544Mbps; DS3: terminate, monitor; E4: terminate; Alarm can to be detected and generated: E1: LOS, LOF, OOF, RAI, AIS, CRCLOFM, MFASOOF, LOFMFAS, MFASRAI, LSS; DS1: LOS, LOF, OOF, RAI, AIS, LSS; E3: LOS, LOF, AIS, RDI; DS3: LOS, LOF, AIS, RAI, LSS, IDLE; E4: LOS, LOF, AIS, RAI, LSS; Alarm generation mode: Continuous; Alternate; Burst; Error can be detected and generated: E1: FAS, CRC4, E-BIT, Code, BIT; DS1: FAS, Code, BIT, CRC6; E3: FAS, BIT; DS3: FAS, C-BIT, P-BIT, FEBE, BIT; E4: FAS, BIT; Error generation mode: Single; Continuous; Alternate; Burst; Rate; N-frame;

11 PDH and DSn Test BERT Pattern PDH and DSn Result Status Statistics Histogram Error Performance APS Propagation Delay Measurement Pattern generation and monitor for O.181 bulk test pattern; Support to generate and detect: PRBS9, PRBS11, PRBS15, PRBS20, PRBS23, PRBS31; Support reversed PRBS pattern: 16bit user define pattern; Display information of current status: Alarms and errors; Event log display: Alarms (seconds); Errors (count and rate); Actual bit rate; Frequency deviation. Start/stop time; All events refresh with 1 second resolution; All alarms and errors detected can be display in histogram, user can see all issues directly; G.821/G.826/M.2100 analysis of received signals based on detected errors and alarms: ES, SES, BBE,AS,UAS and so on; APS (automatic protection switching): Independently select start and complete trigger; All PDH/DSn alarms and errors, bit error, errors with threshold; Number of switchovers indicated by APS protocol; Display and save APS time, frequency, pass/fail, minimum/maximum/ average value. APS time resolution: 1us; Resolution: 0.1us; Measurement max time: 2.0 s.

12 Ethernet (1G and 10G) Ethernet Test Port Ethernet Feature Configuration Encapsulation Electrical interface: 1 port, 10/100/1000M Base-T, SFP-T; Optical interface:1 port, 100/1000M Base-X, SFP; User selectable optical module: 850nm, 1310nm, 1550nm. Optical interface: 1 ports, 10G Base-X, XFP; User selectable optical module: 1310nm, 1550nm. Auto negotiation, full and half duplex, flow control; Monitor/generate, pass-through; Ethernet type II, IEEE802.3 with 802.2, IEEE802.3 with SNAP; Configuration, Monitoring, and Generation Traffic Generation Stacked VLAN Multi stream Error Injection Alarm generation Variable line rate traffic generation, up to full line rate; Traffic generation: continuous, burst, ramp, n-frame, n-burst, n-ramp; Adjustable frame size: 64 bytes to bytes; Frame size: constant, imax, random; User-defined traffic mix of unicast and broadcast frames; Fixed or increment MAC/IP identifier; User programmable DSCP/TOS byte; Configurable IP and Ethernet source and destination addresses (support IPv4 and IPv6 addressing); User programmable TCP/UDP address; Generate pause frames, respond to pause frames; Answer incoming ARP, Ping requests; Up to 3 user-settable VLAN tags; Parameters per VLAN tag: Ethernet type II 0x8100 (802.1Q), 0x88a8 (802.1ad),0x9100, 0x9200, or 0x9300; User-defined VLAN ID, CFI, VLAN priority; Number of streams: up to 16 streams per port can be activated; FCS, IP check sum error, UDP/TCP check sum error; No link; Result, Monitoring and Generation Status Performance Statistics Frame Statistics Frame Distribution Statistics Multi stream Link status, interface type, jabber detected, frames present, MPLS/VLAN, speed, full or half duplex, signal present, bit rate of incoming Ethernet signal, auto negotiation complete; Link partner abilities: speed/duplex; Indicators of utilisation, throughput, errored frames; Signal level indication for optical Ethernet interfaces; Utilisation, throughput, frame rate; Total frames, total testing frames, total not testing frames, unicast/multicast/broadcast frames, number of pause frames; Total VLAN frames; Total MPLS frames; Total errored framed, number of oversized, normal, and runt frame, number of FCS errored; Total valid/frames, <64, , , , , >1518; Display information per steam: Frame loss count/rate, throughput, latency, packet jitter, frames and bytes received and transmitted;

13 Result, Monitoring and Generation Transmit Statistics Filter Total frames, unicast/multicast/broadcast; Filter condition support: Source and destination MAC/IP, IPv6, VLAN ID and VLAN Priority, MPLS, IP TOS, TCP/UDP source and destination port, Ethernet type and IP protocol; BER Test and Service Disruption Test BER Test Error Injection Service Disruption Test Loopback Loopback Test RFC3393 Jitter Test RFC2544 RFC2544 Test Service Activation Test (Y.1564) Service Activation Test Service Configuration Test Service Performance Test Remote Smart Loopback Test Remote Smart Loopback Advanced IP Tools PING Generation and detection of test pattern, count of errors in received test pattern,; Pattern generation: layer 1 to layer 4; Frame loss count and frame loss seconds; BER measurement results; Test pattern: PRBS9, PRBS11, PRBS15, PRBS20, PRBS23, PRBS31, CRPRJ, JTPAT, SPAT, 32bits user defined; FCS, IP check sum error, UDP/TCP check sum error, BIT error; Service disruption test activated as part of BER test: Max/avg service disruption test, resolution: 0.1us; Number of service disruption; Layer 1 to layer 4 loopback test; Advanced loopback test: Packet loss setting: percentage, packet count, time; Loopback drop enable: protocol loss, protocol pass, control, CRC error, IP/TCP/UDP error; G.711, G.723.1, G.729, and so on VoIP packet jitter test; Jitter result: hits, min, max, current, average; Switch/router test and single ended network test mode: Throughput, frame loss, latency, back-to-back; ITU-T Y.1564 service activation Test: Up to 8 services per port; Colour-aware and non-colour-aware in combinations; Test modes: one-way (uni-or bi-directional, symmetrical or asymmetrical), round-trip; Verification against service acceptance criteria: information rate, frame transfer delay, frame delay variation, frame loss rate, availability; Subtest for: CIR, EIR, traffic policing; Step duration: 1-60s (user define); Number of steps: 1 to 4; Result: pass/fail indication, IR (min/avg/max), FL (count/flr), FTD, FDV (min/avg/max (during measurement)); All services tested simultaneously at CIR; Duration: 15min, 2hours, 24 hours, or user defined; Result: pass/fail indication, IR (min/avg/max), FL (count/flr), FTD, FDV (min/avg/max (during measurement)); Use as local unit control another remote unit for RFC2544 and Y.1564 bi-directional testing; Support layer 1 to layer 4 smart loopback test; For connectivity and configuration check: Round trip time (RTT); Support IPv4, TTL, URL;

14 Advanced IP Tools Trace Route VCT Cable Test Flow Control FTP Upload/ Download HTTP Advanced PING (Topology) MPLS Number of MPLS Header Parameter per MPLS Header Statistics Ethernet Frame Capture Capture Buffer Size Capture Data Trace IP route over IP network: Information per hop: PING time, number of ping timeouts; Use for CAT5 cable connectivity check: Status: pass/fail; Fault location; Flow Control Time, us: Pause time: total, last, max, min; Channel; Polarity; Pair Skew; Pause frame count: TX, RX; Use for FTP server and client emulation: Support IPv4 and URL; Username/password; File upload/download; Result: pass/fail indication, upload/download time display; WEB access: Support IPv4 and URL; HTTP access pass/fail; Advance/Fast PING, PING segments of the IP one by one in one time: IP address range: start, end Send count; Up to 3 MPLS header set by user; Timeout (ms); Status: pass/fail indication; User defined label, EXP and TLL fields in each MPLS header; MPLS frame count; 32Kbytes; When capture buffer full: stop; CAP format for display in Wireshark.

15 OTP OTM2502 Ordering Information OTP6200+OTM2502 STANDARD CONFIGURAIOTN Module OTP6200 OTM2502 Accessories Code Description Test platform, support SDH, OTN, Ethernet, Packet Ethernet, OTDR test modules; 10G multi-service test module, include DS1 to STM-64/OC-192 rates PDH/SDH test features; A couple BNC electrical interface for DS1/DS3, E1/E3/E4/STM-1 rates test; SFP port for STM-1/4/16 and OC-3/12/48 SDH/SONET test; XFP port for STM-64/OC-192 SDH/SONET test; PDH/SDH BER test; Alarm generation and monitoring, error injection and monitoring; PDH/SDH APS and SDT test; PDH/SDH performance test according with G.821, G.826, G.828, G.829, M.2100, M.2101; SDH/SONET signal auto detection; SDH through mode, and can insert alarm and errors when use through mode; SDH tributary scan; Propagation delay test; Remote control by PC; Accessories Description LC/PC to LC/PC full-duplex single-mode fibre, 3m, one; CAT5 cable, 3m, one; ohm BNC cables, 2m, two; G 1310nm 15Km LC SFP optical module, one; G 1310nm 2km LC SFP optical module, one; G 1310nm 10Km LC XFP optical module, one; SFP-T electrical module for 10/100/1000M Base-T port, Only for when user order option OPAP- BaseAGeEth; SFP optical port dust proof cap - black - rubber, one; XFP optical port dust proof cap - black - rubber, one; OTP V input and 19V output AC/DC power adapter, one; pins adapter cable, one; OTP6200 disc include user manual and OPWILL remote control software, one; OTP6200 package, one; Factory test report, one; Calibration certificate, one; One year warranty service.

16 SDH Optional Software OPAP-OHSeqCapture OPAP-TCM Ethernet Optional Software (1G) OPAP-BaseAGeEth (Need to order this basic 1GE function firstly) OPAP-Y1564AGeEth OPAP-IPv6AGeEth OPAP-ScanAGeEth OPAP-EautoAGeEth OAPA-EPINGAGeEth OPAP-3MPLSAGeEth OPAP-FXAGeEth Ethernet Optional Software (10G) OTM2502 OPTIONAL CONFIGURATION 256 frames SDH overhead capture and decode capability; SDH N1 and N2 bytes for tandem connection monitoring capability; One 10/100/1000M Base-T and one 1000M Base-X Gigabit Ethernet test; Layer 1 to Layer 4 BERT test; Up to 8 streams generation and analysis with MAC/VLAN/IP/TCP/UDP; RFC2544 standard test with Throughput, Latency, Frame Loss and Back-to-Back; RFC3393 Jitter test for VoIP packets; Layer 1 to Layer 4 loopback and smart loopback test; Enable to drop data packet under loopback mode; Up to 1000M streams generation with 3 Layer VLAN; Ping, Trace Route, FTP Download/Upload, and HTTP tools; Ethernet service disruption test; Packet capture and analysis to 1000M rate; Cable test with CAT5 Length and fault measurement; Enable to generate frame with random length; Enable to generate data streams with increment MAC and IP; Layer 1 bandwidth statistics ; Y.1564 standard service configuration and performance test for SLA QoS with CIR/EIR/Traffic Dropped for GE; IPv6 feature, the test interface can set IPv6 address and also can generate stream with IPv6 for GE; Traffic scan according with destination MAC/IP, source MAC/IP, 3 layer VLAN, 3 layer MPLS in-service test for GE; Advance auto-negotiation, can set the remote equipment auto-negotiation the speed and duplex as you want for GE; Advance/Fast PING, PING segments of the IP one by one in one time for GE; Up to 1000M streams generation with 3 layer MPLS label for GE; One 100M Base-X optical port; OPAP-BaseTGeEth (Need to order this basic 10GE test function firstly) One 10G Base-X Ethernet test; Layer 1 to Layer 4 BERT test; Up to 16 streams generation and analysis with MAC/VLAN/IP/TCP/UDP; RFC2544 standard test with Throughput, Latency, Frame Loss, Back-to-Back and Jitter; Layer 1 to Layer 4 loopback and smart loopback test; Enable to drop data packet under loopback mode; Up to 10G streams generation with 3 Layer VLAN; Ping, Trace Route, FTP Download/Upload, and HTTP tools; Ethernet service disruption test; Packet capture and analysis to 10G rate; Enable to generate frame with increment, decrement, random length; Enable to generate data streams with increment, MAC, IP, VLAN, MPLS, and Port Number; Bi-directional test; Layer 1 bandwidth statistics;

17 Ethernet Optional Software (10G) OPAP-Y1564TGeEth OPAP-IPv6TGeEth OAPA-EPINGTGeEth OPAP-3MPLSTGeEth Optional Hardware OTM2502 OPTIONAL CONFIGURATION Y.1564 standard service configuration and performance test for SLA QoS with CIR/EIR/Traffic Dropped for 10GE; IPv6 feature, the test interface can set IPv6 address and also can generate stream with IPv6 for 10GE; Advance/Fast PING, PING segments of the IP one by one in one time for 10GE; Up to 10G rates generation with 3 layer MPLS label for 10GE; OTP6200 lithium polymer rechargeable battery; OPAP-Twowarranty Two years extended warranty service; G-850nm-550m-MM-LC-SFP-DDM; G-1310nm-15km-SM-LC-SFP-DDM; G-1550nm-40km-SM-LC-SFP-DDM; G-1310nm-2km-SM-LC-SFP-DDM; G-1550nm-40km-SM-LC-SFP-DDM; G-1310nm-10km-SM-LC-XFP-DDM; G-1550nm-40KM-SM-LC-XFP-DDM. Notes: Product ordering information may update along with the product upgrade, please refer to the final version provided by our sales.

18 OTP OTM2512 Ordering Information OTP6200+OTM2512 STANDARD CONFIGURAIOTN Module OTP6200 OTM2512 Accessories Code Description Test platform, support SDH, OTN, Ethernet, Packet Ethernet, OTDR test modules; 10G multi-service test module, include DS1 to OTU2e rates PDH/SDH/OTN test features; A couple BNC electrical interface for DS1/DS3, E1/E3/E4/STM-1 rates test; SFP port for STM-1/4/16 and OC-3/12/48 SDH/SONET test; SFP port for OTU1 test; XFP port for STM-64/OC-192 SDH/SONET test; XFP port for OTU2, OTU1e and OTU2e test; PDH/SDH/OTN BER test; Alarm generation and monitoring, error injection and monitoring; PDH/SDH/OTN APS and SDT test; FEC test according with ITU-T O.182; PDH/SDH performance test according with G.821, G.826, G.828, G.829, M.2100, M.2101; SDH/SONET signal auto detection; SDH/OTN through mode, and can insert alarm and errors when use through mode; SDH tributary scan; Propagation delay test; Remote control by PC; Accessories Description LC/PC to LC/PC full-duplex single-mode fibre, 3m, one; CAT5 cable, 3m, one; ohm BNC cables, 2m, two; G 1310nm 15Km LC SFP optical module, one; G 1310nm 2km LC SFP optical module, one; G 1310nm 10Km LC XFP optical module, one; SFP-T electrical module for 10/100/1000M Base-T port, Only for when user order option OPAP- BaseAGeEth; SFP optical port dust proof cap - black - rubber, one; XFP optical port dust proof cap - black - rubber, one; OTP V input and 19V output AC/DC power adapter, one; pins adapter cable, one; OTP6200 disc include user manual and OPWILL remote control software, one; OTP6200 package, one; Factory test report, one; Calibration certificate, one; One year warranty service.

19 SDH and OTN Optional Software OPAP-OHSeqCapture OPAP-ODU0Mapping OPAP-ODUFLEXMapping OPAP-TCM Ethernet Optional Software (1G) OPAP-BaseAGeEth (Need to order this basic 1GE function firstly) OPAP-Y1564AGeEth OPAP-IPv6AGeEth OPAP-ScanAGeEth OPAP-EautoAGeEth OAPA-EPINGAGeEth OPAP-3MPLSAGeEth OPAP-FXAGeEth Ethernet Optional Software (10G) OTM2512 OPTIONAL CONFIGURATION 256 frames SDH/OTN overhead capture and decode capability; ODU0 mapping capability test; ODU flex mapping capability test; SDH N1 and N2 bytes for tandem connection monitoring capability; One 10/100/1000M Base-T and one 1000M Base-X Gigabit Ethernet test; Layer 1 to Layer 4 BERT test; Up to 8 streams generation and analysis with MAC/VLAN/IP/TCP/UDP; RFC2544 standard test with Throughput, Latency, Frame Loss and Back-to-Back; RFC3393 Jitter test for VoIP packets; Layer 1 to Layer 4 loopback and smart loopback test; Enable to drop data packet under loopback mode; Up to 1000M streams generation with 3 Layer VLAN; Ping, Trace Route, FTP Download/Upload, and HTTP tools; Ethernet service disruption test; Packet capture and analysis to 1000M rate; Cable test with CAT5 Length and fault measurement; Enable to generate frame with random length; Enable to generate data streams with increment MAC and IP; Layer 1 bandwidth statistics; Y.1564 standard service configuration and performance test for SLA QoS with CIR/EIR/Traffic Dropped for GE; IPv6 feature, the test interface can set IPv6 address and also can generate stream with IPv6 for GE; Traffic scan according with destination MAC/IP, source MAC/IP, 3 layer VLAN, 3 layer MPLS in-service test for GE; Advance auto-negotiation, can set the remote equipment auto-negotiation the speed and duplex as you want for GE; Advance/Fast PING, PING segments of the IP one by one in one time for GE; Up to 1000M streams generation with 3 layer MPLS label for GE; One 100M Base-X optical port; OPAP-BaseTGeEth (Need to order this basic 10GE test function firstly) One 10G Base-X Ethernet test Layer 1 to Layer 4 BERT test Up to 16 streams generation and analysis with MAC/VLAN/IP/TCP/UDP RFC2544 standard test with Throughput, Latency, Frame Loss, Back-to-Back and Jitter Layer 1 to Layer 4 loopback and smart loopback test Enable to drop data packet under loopback mode Up to 10G streams generation with 3 Layer VLAN Ping, Trace Route, FTP Download/Upload, and HTTP tools Ethernet service disruption test Packet capture and analysis to 10G rate Enable to generate frame with increment, decrement, random length Enable to generate data streams with increment, MAC, IP, VLAN, MPLS, and Port Number

20 Ethernet Optional Software (10G) OTM2512 OPTIONAL CONFIGURATION OPAP-BaseTGeEth OPAP-Y1564TGeEth OPAP-IPv6TGeEth OAPA-EPINGTGeEth OPAP-3MPLSTGeEth Bi-directional test Layer 1 bandwidth statistics Y.1564 standard service configuration and performance test for SLA QoS with CIR/EIR/Traffic Dropped for 10GE; IPv6 feature, the test interface can set IPv6 address and also can generate stream with IPv6 for 10GE; Advance/Fast PING, PING segments of the IP one by one in one time for 10GE; Up to 10G rates generation with 3 layer MPLS label for 10GE; Optional Hardware OTP6200 lithium polymer rechargeable battery; OPAP-Twowarranty Two years extended warranty service; G-850nm-550m-MM-LC-SFP-DDM; G-1310nm-15km-SM-LC-SFP-DDM; G-1550nm-40km-SM-LC-SFP-DDM; G-1310nm-2km-SM-LC-SFP-DDM; G-1550nm-40km-SM-LC-SFP-DDM; G-1310nm-10km-SM-LC-XFP-DDM; G-1550nm-40KM-SM-LC-XFP-DDM. Notes: Product ordering information may update along with the product upgrade, please refer to the final version provided by our sales. Please visit our website for the further information: www. OPWILL.com OPWILL TECHNOLOGIES (BEIJING) CO., LTD. Add: Room 415, Digital Media Building, No.7 Shangdi Information Road, Haidian District, Beijing, PRC Tel: +86(10) /2866/3382 Fax: +86(10) Copyright OPWILL Technologies (Beijing) Co., Ltd All Rights Reserved.