Table of Contents. 1 TFTP Configuration Commands 1-1 TFTP Client Configuration Commands 1-1 tftp-server acl 1-1 tftp 1-2 tftp ipv6 1-3
|
|
- Frederica Gardner
- 5 years ago
- Views:
Transcription
1 Table of Contents 1 TFTP Configuration Commands 1-1 TFTP Client Configuration Commands 1-1 tftp-server acl 1-1 tftp 1-2 tftp ipv6 1-3 i
2 1 TFTP Configuration Commands TFTP Client Configuration Commands tftp-server acl tftp-server [ ipv6 ] acl acl-number undo tftp-server [ ipv6 ] acl System view ipv6: References an IPv6 ACL. If it is not specified, an IPv4 ACL is referenced. acl-number: Number of a basic ACL, in the range 2000 to Use the tftp server acl command to control the device s access to a specific TFTP server using an ACL. Use the undo tftp server acl command to restore the default. By default, no ACL is used to control the device s access to TFTP servers. You can use the rules in an ACL to allow or permit the device s access to a specific TFTP server in a network. For more information about ACL, see ACL Overview or IPv4 ACL Configuration or IPv6 ACL Configuration in the Configuration Guide - Part 7 - ACL QoS. Examples # Allow the device to access the TFTP server with the IP address of only (in IPv4 networking environment). <Sysname> system-view [Sysname] acl number 2000 [Sysname-acl-basic-2000] rule permit source [Sysname-acl-basic-2000] quit [Sysname] tftp-server acl 2000 # Allow the device to access the TFTP server with the IP address of 2001::1 only (in IPv6 networking environment). 1-1
3 <Sysname> system-view [Sysname] acl ipv6 number 2001 [Sysname-acl6-basic-2001] rule permit source 2001::1/128 [Sysname-acl6-basic-2001] quit [Sysname] tftp-server ipv6 acl 2001 tftp tftp server-address { get put sget } source-filename [ destination-filename ] [ [ vpn-instance vpn-instance-name ] [ source { interface interface-type interface-number ip source-ip-address } ] ] User view server-address: IP address or host name of a TFTP server. get: Downloads a file in normal mode. put: Uploads a file. sget: Downloads a file in secure mode. source-filename: Source file name. destination-filename: Destination file name. vpn-instance vpn-instance-name: Specifies the VPN where a TFTP server resides. The vpn-instance-name argument refers to the name of a VPN instance, which is a case-sensitive string of 1 to 31 characters. source: Configures parameters for source address binding. interface interface-type interface-number: Specifies the source interface by its type and number. The primary IP address configured on the source interface is the source IP address of the packets sent by TFTP. If no primary IP address is configured on the source interface, the transmission fails. ip source-ip-address: Specifies the source IP address for the current TFTP client to transmit packets. This source address must be an IP address that has been configured on the device. Use the tftp command to upload files from the local device to a TFTP server or download files from the TFTP server to the local device. If no destination file name is specified, a file is saved using the same name as that on the remote FTP server to the current working directory of the user (namely, the working directory where the tftp command is executed). This command applies to IPv4 networks. 1-2
4 Examples # To upgrade the device, download the newest.bin file from the TFTP server with the IP address of and save it to both the root directory on the flash of the master and the root directory on the flash of the slave (with the member ID 2). <Sysname> tftp get newest.bin startup.bin. Downloading file from remote TFTP server, please wait... TFTP: bytes received in 13 second(s) // Download the file from the TFTP server to the root directory on the flash of the master. <Sysname> tftp get newest.bin slot2#flash:/startup.bin tftp ipv6 Downloading file from remote TFTP server, please wait... TFTP: bytes received in 14 second(s) // Download the file from the TFTP server to the root directory on the flash of the slave. tftp ipv6 tftp-ipv6-server [ -i interface-type interface-number ] { get put } source-file [ destination-file ] User view tftp-ipv6-server: IPv6 address or host name (a string of 1 to 46 characters) of a TFTP server. -i interface-type interface-number: Specifies the egress interface by its type and number. This parameter can be used only in case that the TFTP server address is a link local address and the specified egress interface must have a link local address (For the configuration of link local address, see IPv6 Basics Configuration in the Configuration Guide - Part 4 - IP Services). get: Downloads a file. put: Uploads a file. source-filename: Source filename. destination-filename: Destination filename. If not specified, this filename is the same as the source filename. Use the tftp ipv6 command to download a specified file from a TFTP server or upload a specified local file to a TFTP server. 1-3
5 This command applies to IPv6 networks. Examples # Download filetoget.txt from the TFTP server. <Sysname> tftp ipv6 fe80::250:daff:fe91:e058 -i vlan-interface 1 get filetoget.txt... Downloading file from remote TFTP server, please wait... TFTP: bytes received in 2 second(s) 1-4
Contents. TFTP configuration commands 29 display tftp client configuration 29 tftp-server acl 29 tftp 30 tftp client source 32 tftp ipv6 33
Contents FTP configuration commands 1 FTP server configuration commands 1 display ftp-server 1 display ftp-user 2 free ftp user 3 ftp server acl 3 ftp server enable 4 ftp timeout 5 ftp update 5 FTP client
More informationTable of Contents 1 FTP Configuration Commands TFTP Configuration Commands 2-1
Table of Contents 1 FTP Configuration Commands 1-1 FTP Client Configuration Commands 1-1 ascii 1-1 binary 1-2 bye 1-2 cd 1-3 cdup 1-4 close 1-4 debugging 1-5 delete 1-6 dir 1-6 disconnect 1-8 display ftp
More informationContents. TFTP configuration commands 28 display tftp client configuration 28 tftp-server acl 28 tftp 29 tftp client source 30 tftp ipv6 31
Contents FTP configuration commands 1 FTP server configuration commands 1 display ftp-server 1 display ftp-user 2 free ftp user 3 ftp server acl 3 ftp server enable 4 ftp timeout 4 ftp update 5 FTP client
More informationTable of Contents 1 FTP Configuration Commands TFTP Configuration Commands 2-1
Table of Contents 1 FTP Configuration Commands 1-1 FTP Server Configuration Commands 1-1 display ftp-server 1-1 display ftp-user 1-2 free ftp user 1-3 ftp server acl 1-3 ftp server enable 1-4 ftp timeout
More informationUsing the emergency shell 1
Contents Using the emergency shell 1 Emergency shell usage guidelines 1 Managing the file systems 1 Obtaining a system image from an FTP/TFTP server 2 Configuring the management Ethernet interface 2 Checking
More informationContents. FTP commands 1
Contents FTP commands 1 FTP server commands 1 display ftp-server 1 display ftp-user 1 free ftp user 2 free ftp user-ip 3 free ftp user-ip ipv6 3 ftp server acl 4 ftp server dscp 5 ftp server enable 5 ftp
More informationHP High-End Firewalls
HP High-End Firewalls NAT and ALG Command Reference Part number: 5998-2639 Software version: F1000-E/Firewall module: R3166 F5000-A5: R3206 Document version: 6PW101-20120706 Legal and notice information
More informationLoopback detection configuration commands
Contents Loopback detection configuration commands 1 display loopback-detection 1 loopback-detection action 2 loopback-detection enable 2 loopback-detection interval-time 3 i Loopback detection configuration
More informationH3C S7500E-X OSPF Configuration Examples
H3C S7500E-X OSPF Configuration Examples Copyright 2015 Hangzhou H3C Technologies Co., Ltd. All rights reserved. No part of this manual may be reproduced or transmitted in any form or by any means without
More informationCommand Manual MAC Address Table Management H3C S5500-EI Series Ethernet Switches. Table of Contents
Table of Contents Table of Contents... 1-1 1.1 MAC Address Table Management... 1-1 1.1.1 display mac-address... 1-1 1.1.2 display mac-address aging-time... 1-2 1.1.3 mac-address (Ethernet port view)...
More informationH3C SecPath Series High-End Firewalls
H3C SecPath Series High-End Firewalls NAT and ALG Command Reference Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Software version: SECPATH1000FE&SECBLADEII-CMW520-R3166 SECPATH5000FA-CMW520-R3206
More informationARP attack protection commands
Contents ARP attack protection commands 1 Unresolvable IP attack protection commands 1 arp resolving-route enable 1 arp source-suppression enable 1 arp source-suppression limit 2 display arp source-suppression
More informationHP 5920 & 5900 Switch Series
HP 5920 & 5900 Switch Series Security Command Reference Part number: 5998-2887 Software version: Release2208 Document version: 6W100-20130228 Legal and notice information Copyright 2013 Hewlett-Packard
More informationTable of Contents 1 Commands for Access Controller Switch Interface Board 1-1
Table of Contents 1 Commands for Access Controller Switch Interface Board 1-1 Commands for Access Controller and Access Controller Switch Interface Board 1-1 acl (user interface view) 1-1 activation-key
More informationH3C S5830V2 & S5820V2 Switch Series
H3C S5830V2 & S5820V2 Switch Series Security Command Reference Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Software version: Release2108 Document version: 6W101-20120531 Copyright 2012, Hangzhou
More informationOperation Manual MCE H3C S3610&S5510 Series Ethernet Switches. Table of Contents
Table of Contents Table of Contents Chapter 1 MCE Overview... 1-1 1.1 MCE Overview... 1-1 1.1.1 Introduction to BGP/MPLS VPN... 1-1 1.1.2 BGP/MPLS VPN Concepts... 1-2 1.1.3 Introduction to MCE... 1-5 1.1.4
More informationLogin management commands
Contents Login management commands 1 CLI login configuration commands 1 display telnet client configuration 1 telnet 1 telnet ipv6 2 telnet server enable 3 User interface configuration commands 3 acl (user
More informationTable of Contents 1 FTP and SFTP Configuration TFTP Configuration 2-1
Table of Contents 1 FTP and SFTP Configuration 1-1 Introduction to FTP and SFTP 1-1 Introduction to FTP 1-1 Introduction to SFTP 1-1 FTP Configuration 1-2 FTP Configuration: A Switch Operating as an FTP
More informationOperation Manual ARP H3C S5500-SI Series Ethernet Switches. Table of Contents
Table of Contents Table of Contents... 1-1 1.1 ARP Overview... 1-1 1.1.1 ARP Function... 1-1 1.1.2 ARP Message Format... 1-1 1.1.3 ARP Address Resolution Process... 1-2 1.1.4 ARP Mapping Table... 1-3 1.2
More informationConfiguring ACLs. ACL overview. ACL categories. ACL numbering and naming
Contents Configuring ACLs 1 ACL overview 1 ACL categories 1 ACL numbering and naming 1 Match order 2 ACL rule numbering 3 Implementing time-based ACL rules 3 IPv4 fragments filtering with ACLs 3 Flow templates
More informationOperation Manual System Management. Table of Contents
Table of Contents Table of Contents Chapter 1 File System Management... 1-1 1.1 File System Configuration... 1-1 1.1.1 File System Overview... 1-1 1.1.2 Directory... 1-1 1.1.3 File... 1-2 1.1.4 Storage
More informationContents. Tunneling commands 1
Contents Tunneling commands 1 bandwidth 1 default 1 description 2 destination 3 4 interface tunnel 7 mtu 8 reset counters interface tunnel 9 service 9 shutdown 10 source 11 tunnel dfbit enable 12 tunnel
More informationTable of Contents 1 QoS Overview QoS Policy Configuration Priority Mapping Configuration 3-1
Table of Contents 1 QoS Overview 1-1 Introduction to QoS 1-1 Networks Without QoS Guarantee 1-1 QoS Requirements of New Applications 1-1 Congestion: Causes, Impacts, and Countermeasures 1-2 Causes 1-2
More informationH3C S12500 Series Routing Switches
H3C S12500 Series Routing Switches Security Command Reference Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Software version: S12500-CMW710-R7128 Document version: 6W710-20121130 Copyright 2012,
More informationTable of Contents 1 PPP Configuration Commands PPPoE Configuration Commands 2-1
Table of Contents 1 PPP Configuration Commands 1-1 PPP Configuration Commands 1-1 ip address ppp-negotiate 1-1 link-protocol ppp 1-2 mtu 1-2 ppp account-statistics enable 1-3 ppp authentication-mode 1-3
More informationHP 5920 & 5900 Switch Series
HP 5920 & 5900 Switch Series MCE Configuration Guide Part number: 5998-2896 Software version: Release2207 Document version: 6W100-20121130 Legal and notice information Copyright 2012 Hewlett-Packard Development
More informationMOP for upgrading StoneOS
MOP for upgrading StoneOS Make a backup of current configurations A. WebUI: Refer to the image below, click tab System menu Configuration File Management, check the box before the Startup configuration
More informationHP 3600 v2 Switch Series
HP 3600 v2 Switch Series Fundamentals Command Reference Part number: 5998-2359 Software version: Release 2101 Document version: 6W101-20130930 Legal and notice information Copyright 2013 Hewlett-Packard
More informationHP 3600 v2 Switch Series
HP 3600 v2 Switch Series IRF Configuration Guide Part number: 5998-2349a Software version: Release 2108P01 Document version: 6W100-20131130 Legal and notice information Copyright 2013 Hewlett-Packard Development
More informationHP 5820X & 5800 Switch Series IRF. Configuration Guide. Abstract
HP 5820X & 5800 Switch Series IRF Configuration Guide Abstract This document describes the software features for the HP 5820X & 5800 Series products and guides you through the software configuration procedures.
More informationRelease Notes: SoundPoint/SoundStation IP - BootROM
Software Revision These release notes cover Polycom s SoundPoint/SoundStation IP - BootROM version 3.0.1. Document Revision These release notes may be updated during the life of this release as any issues
More informationOperation Manual Cluster Management. Table of Contents
Table of Contents Table of Contents... 1-1 1.1 HGMP V1 Over... 1-1 1.2 HGMP Server Configuration... 1-2 1.2.1 Enabling HGMP Server on a Management Device... 1-2 1.2.2 Upgrading Software on a Switch through
More informationH3C S6800 Switch Series
H3C S6800 Switch Series OpenFlow Command Reference New H3C Technologies Co., Ltd. http://www.h3c.com Software version: Release 2609 and later Document version: 6W103-20190104 Copyright 2019, New H3C Technologies
More informationContents. Tunneling commands 1
Contents Tunneling commands 1 bandwidth 1 default 1 description 2 destination 2 display interface tunnel 3 interface tunnel 7 mtu 8 reset counters interface 9 service 10 shutdown 11 source 11 tunnel dfbit
More informationHP 3600 v2 Switch Series
HP 3600 v2 Switch Series Fundamentals Command Reference Part number: 5998-7608 Software version: Release 2110P02 Document version: 6W100-20150305 Legal and notice information Copyright 2015 Hewlett-Packard
More informationH3C S5500-HI Switch Series
H3C S5500-HI Switch Series ACL and QoS Command Reference Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Software version: Release 5501 Document version: 6W100-20140103 Copyright 2014, Hangzhou
More informationConfiguring BPDU tunneling
Contents Configuring BPDU tunneling 1 Introduction to BPDU tunneling 1 Background 1 BPDU Tunneling implementation 2 Configuring BPDU tunneling 3 Configuration prerequisites 3 Enabling BPDU tunneling for
More informationH3C S5130-EI Switch Series
H3C S5130-EI Switch Series OpenFlow Command Reference New H3C Technologies Co., Ltd. http://www.h3c.com Software version: Release 311x Document version: 6W102-20180323 Copyright 2016-2018, New H3C Technologies
More informationH3C SecBlade NetStream Card Configuration Examples
H3C SecBlade NetStream Card Configuration Examples Copyright 2012 Hangzhou H3C Technologies Co., Ltd. All rights reserved. No part of this manual may be reproduced or transmitted in any form or by any
More informationFile Transfers. Contents
A File Transfers Contents Overview.................................................... A-3................................ A-3 General Software Download Rules............................ A-4 Using TFTP
More informationLoop detection commands 1
Contents Loop detection commands 1 display loopback-detection 1 loopback-detection action 1 loopback-detection enable 2 loopback-detection global action 3 loopback-detection global enable 4 loopback-detection
More informationHP A3100 v2 Switch Series
HP A3100 v2 Switch Series Fundamentals Command Reference HP A3100-8 v2 SI Switch (JG221A) HP A3100-16 v2 SI Switch (JG222A) HP A3100-24 v2 SI Switch (JG223A) HP A3100-8 v2 EI Switch (JD318B) HP A3100-16
More informationLogging in to the CLI
Contents Logging in to the CLI 1 Login methods 1 Logging in through the console port 2 Introduction 2 Configuration procedure 2 Logging in through the AUX port 5 Configuration prerequisites 5 Configuration
More informationHP FlexFabric 5930 Switch Series
HP FlexFabric 5930 Switch Series MCE Configuration Guide Part number: 5998-4625 Software version: Release 2406 & Release 2407P01 Document version: 6W101-20140404 Legal and notice information Copyright
More informationBasic MPLS commands. display mpls forwarding ilm. Syntax. Views. Predefined user roles. Parameters. Usage guidelines. Examples
Contents Basic MPLS commands 1 display mpls forwarding ilm 1 display mpls forwarding nhlfe 2 display mpls interface 4 display mpls label 5 display mpls lsp 6 display mpls lsp statistics 10 display mpls
More informationOperation Manual SNMP. Table of Contents
Table of Contents Table of Contents... 1-1 1.1 SNMP Overview... 1-1 1.1.1 Introduction to SNMP... 1-1 1.1.2 SNMP Versions and Supported MIB... 1-1 1.2 Configuring SNMP... 1-3 1.2.1 Setting Community Names...
More informationHP Load Balancing Module
HP Load Balancing Module System Maintenance Configuration Guide Part number: 5998-4221 Software version: Feature 3221 Document version: 6PW100-20130326 Legal and notice information Copyright 2013 Hewlett-Packard
More informationFinding Feature Information, page 2 Information About DHCP Snooping, page 2 Information About the DHCPv6 Relay Agent, page 8
This chapter describes how to configure the Dynamic Host Configuration Protocol (DHCP) on a Cisco NX-OS device. This chapter includes the following sections: Finding Feature Information, page 2 Information
More informationHP 5500 HI Switch Series
HP 5500 HI Switch Series IRF Configuration Guide Part number: 5998-2376a Software version: Release 5203 and Release 5206 Document version: 6W102-20140228 Legal and notice information Copyright 2014 Hewlett-Packard
More informationTable of Contents. 2 MIB Configuration Commands 2-1 display mib-style 2-1 mib-style 2-1
Table of Contents 1 SNMP Configuration Commands 1-1 SNMP Configuration Commands 1-1 display snmp-agent community 1-1 display snmp-agent group 1-2 display snmp-agent local-engineid 1-3 display snmp-agent
More informationTable of Contents Chapter 1 Link Aggregation Configuration
Table of Contents Table of Contents... 1-1 1.1 Over... 1-1 1.2 LACP... 1-2 1.3 Link Aggregation Types... 1-2 1.3.1 Manual Aggregation and Static LACP Aggregation... 1-2 1.3.2 Dynamic LACP Aggregation...
More informationConfiguring MPLS L2VPN
Contents Configuring MPLS L2VPN 1 MPLS L2VPN overview 1 About MPLS L2VPN 1 Comparison with traditional VPN 2 Comparison with MPLS L3VPN 2 Basic concepts 2 MPLS L2VPN implementation 3 MPLS L2VPN configuration
More informationHP FlexFabric 5930 Switch Series
HP FlexFabric 5930 Switch Series Layer 3 IP Services Command Reference Part number: 5998-4568 Software version: Release 2406 & Release 2407P01 Document version: 6W101-20140404 Legal and notice information
More informationConfiguring MPLS L2VPN
Contents Configuring MPLS L2VPN 1 Overview 1 Comparison with traditional VPN 1 Comparison with MPLS L3VPN 2 Basic concepts 2 MPLS L2VPN implementation 3 MPLS L2VPN configuration task list 4 Configuring
More informationPortal configuration commands
Contents Portal configuration commands 1 display portal acl 1 display portal connection statistics 5 display portal free-rule 7 display portal interface 9 display portal-roaming 11 display portal server
More informationHPE FlexNetwork 5130 HI Switch Series Troubleshooting Guide
HPE FlexNetwork 5130 HI Switch Series Troubleshooting Guide Part number: 5200-0013 Document version: 6W100-20160129 The information in this document is subject to change without notice. Copyright 2016
More informationHP FlexFabric 7900 Switch Series
HP FlexFabric 7900 Switch Series MCE Configuration Guide Part number: 5998-6188 Software version: Release 2117 and Release 2118 Document version: 6W100-20140805 Legal and notice information Copyright 2014
More informationCommand Manual (For Soliton) VLAN-VPN. Table of Contents
Table of Contents Table of Contents Chapter 1 VLAN-VPN Configuration Commands... 1-1 1.1 VLAN-VPN Configuration Commands... 1-1 1.1.1 display port vlan-vpn... 1-1 1.1.2 vlan-vpn enable... 1-2 1.1.3 vlan-vpn
More informationSecBlade Firewall Cards NAT Configuration Examples
SecBlade Firewall Cards NAT Configuration Examples Keywords: NAT, PAT, private IP address, public IP address, IP address pool Abstract: This document describes the characteristics, applications scenarios,
More informationH3C S5120-EI Switch Series
H3C S5120-EI Switch Series IP Multicast Command Reference Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Software version: Release 2210 Document version: 6W100-20110915 Copyright 2011, Hangzhou
More informationLogging in through SNMP from an NMS 22 Overview 22 Configuring SNMP agent 22 NMS login example 24
Contents Logging in to the CLI 1 Login methods 1 Logging in through the console or AUX port 2 Introduction 2 Configuration procedure 2 Logging in through Telnet 6 Introduction 6 Logging in to the switch
More informationEmergency shell commands 1
Contents Emergency shell commands 1 copy 1 delete 1 dir 2 display copyright 4 display install package 4 display interface m-eth0 5 display ip routing-table 7 display ipv6 routing-table 7 display version
More informationContents. Configuring SSH 1
Contents Configuring SSH 1 Overview 1 How SSH works 1 SSH authentication methods 2 SSH support for Suite B 3 FIPS compliance 3 Configuring the device as an SSH server 4 SSH server configuration task list
More informationACL Rule Configuration on the WAP371
Article ID: 5089 ACL Rule Configuration on the WAP371 Objective A network access control list (ACL) is an optional layer of security that acts as a firewall for controlling traffic in and out of a subnet.
More informationBGP Support for IP Prefix Export from a VRF Table into the Global Table
BGP Support for IP Prefix Export from a VRF Table into the Global Table This feature allows a network administrator to export IP prefixes from a VRF table into the global routing table. Finding Feature
More informationThe term "router" in this document refers to both routers and Layer 3 switches. Step Command Remarks. ipv6 host hostname ipv6-address
Contents Configuring IPv6 DNS 1 Overview 1 Configuring the IPv6 DNS client 1 Configuring static domain name resolution 1 Configuring dynamic domain name resolution 1 Displaying and maintaining IPv6 DNS
More informationTable of Contents 1 System Maintenance and Debugging Commands 1-1
Table of Contents 1 System Maintenance and Debugging Commands 1-1 System Maintenance Commands 1-1 ping 1-1 ping ipv6 1-5 tracert 1-6 tracert ipv6 1-7 System Debugging Commands 1-8 debugging 1-8 display
More informationH3C SecPath Series High-End Firewalls
H3C SecPath Series High-End Firewalls Attack Protection Command Reference Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Software version: SECPATHF1000SAI&F1000AEI&F1000ESI-CMW520-R3721 SECPATH5000FA-CMW520-F3210
More informationUpgrading software. Router software overview. Software upgrade configuration task list
Contents Upgrading software 1 Router software overview 1 Software upgrade configuration task list 1 Upgrading system software from BootWare menu 2 BootWare main menu 2 BootWare submenus 3 Using TFTP/FTP
More informationConfiguring IPv6 DNS. Introduction to IPv6 DNS. Configuring the IPv6 DNS client. Configuring static domain name resolution
Contents Configuring IPv6 DNS 2 Introduction to IPv6 DNS 2 Configuring the IPv6 DNS client 2 Configuring static domain name resolution 2 Configuring dynamic domain name resolution 2 Displaying and maintaining
More informationH3C SecPath Series Firewalls and UTM Devices
H3C SecPath Series Firewalls and UTM Devices Attack Protection Command Reference Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Software version: F100 series: ESS 5132 F1000-A-EI: Feature 3722
More informationCisco ME 3400 Ethernet Access Switch Cisco IOS Commands
CHAPTER 2 Cisco ME 3400 Ethernet Access Switch Cisco IOS Commands aaa accounting dot1x Use the aaa accounting dot1x global configuration command to enable authentication, authorization, and accounting
More informationConfiguring ACL Logging
This chapter contains the following sections: Information About ACL Logging, page 1 Guidelines and Limitations for ACL Logging, page 2, page 2 Verifying ACL Logging Configuration, page 4 Configuration
More informationTable of Contents 1 Monitor Link Configuration Commands 1-1
Table of Contents 1 Monitor Link Configuration Commands 1-1 Monitor Link Configuration Commands 1-1 display monitor-link group 1-1 monitor-link group 1-2 port 1-2 port monitor-link group 1-3 i 1 Monitor
More informationConfiguring Classification
CHAPTER 3 This chapter describes how to configure classification on the Cisco Nexus 7000 Series NX-OS device. This chapter includes the following sections: Information About Classification, page 3-1 Licensing
More informationUsing Cisco Unity Express Software
Using Cisco Unity Express Software Last Updated: May 1, 2006 This chapter provides helpful tips for understanding and configuring Cisco Unity Express software using the command-line interface (CLI). It
More informationTable of Contents 1 Port Mirroring Configuration 1-1
Table of Contents 1 Port Mirroring Configuration 1-1 Introduction to Port Mirroring 1-1 Classification of Port Mirroring 1-1 Implementing Port Mirroring 1-2 Other Functions Supported by Port Mirroring
More informationICC INDUSTRIAL CONTROL COMMUNICATIONS, INC.
Recovering A Wired Ethernet Device s Firmware Via TFTP This document details the method for recovering a wired Ethernet device s application firmware image via TFTP. This document applies to those ICC
More informationTable of Contents. 2 MIB Style Configuration 2-1 Setting the MIB Style 2-1 Displaying and Maintaining MIB 2-1
Table of Contents 1 SNMP Configuration 1-1 SNMP Overview 1-1 SNMP Mechanism 1-1 SNMP Protocol Version 1-2 MIB Overview 1-2 SNMP Configuration 1-3 Configuring SNMP Logging 1-5 Introduction to SNMP Logging
More informationOperation Manual MPLS VLL. Table of Contents
Table of Contents Table of Contents... 1-1 1.1 MPLS VLL Overview... 1-2 1.1.1 Concepts in MPLS VLL... 1-2 1.1.2 Introduction to MPLS VLL... 1-2 1.1.3 Packet Forwarding... 1-3 1.1.4 Implementation... 1-4
More informationHP 5820X & 5800 Switch Series IRF. Command Reference. Abstract
HP 5820X & 5800 Switch Series IRF Command Reference Abstract This document describes the commands and command syntax options available for the HP 5820X & 5800 Series products. This document is intended
More informationTable of Contents 1 Basic Configuration Commands 1-1
Table of Contents 1 Basic Configuration Commands 1-1 Basic Configuration Commands 1-1 clock datetime 1-1 clock summer-time one-off 1-1 clock summer-time repeating 1-2 clock timezone 1-4 command-privilege
More informationClient QoS Association Settings on the WAP371
Article ID: 5091 Client QoS Association Settings on the WAP371 Objective Client Quality of Service (QoS) Association is used to control the wireless clients connected to the network, and allows you to
More informationDXS-3600 Series Layer 3 Managed 10Gigabit Ethernet Switch Web UI Reference Guide
1 Information in this document is subject to change without notice. Reproduction of this document in any manner, without the written permission of the D-Link Corporation, is strictly forbidden. Trademarks
More informationTable of Contents 1 Basic Configuration Commands 1-1
Table of Contents 1 Basic Configuration Commands 1-1 Basic Configuration Commands 1-1 clock datetime 1-1 clock summer-time one-off 1-2 clock summer-time repeating 1-3 clock timezone 1-4 command-privilege
More informationFile system management commands 1
Contents File system management commands 1 cd 1 copy 3 delete 5 dir 7 fdisk 9 file prompt 11 fixdisk 11 format 12 gunzip 12 gzip 13 md5sum 14 mkdir 14 more 15 mount 16 move 17 pwd 18 rename 18 reset recycle-bin
More informationVPLS configuration commands
Contents VPLS configuration commands 1 bandwidth 1 broadcast-restrain 1 description 2 display bgp vpls 3 display l2vpn fast-switch-group 8 display mac-address vsi 9 display mpls l2vpn fib ac vpls 10 display
More informationHP FlexFabric 5700 Switch Series
HP FlexFabric 5700 Switch Series Security Command Reference Part number: 5998-6695 Software version: Release 2416 Document version: 6W100-20150130 Legal and notice information Copyright 2015 Hewlett-Packard
More informationH3C S7500E Software Upgrade Configuration Examples
H3C S7500E Software Upgrade Configuration Examples Copyright 2015 Hangzhou H3C Technologies Co., Ltd. A l l ri g h t s re s e r ve d. No part of this manual may be reproduced or transmitted in any form
More informationConfiguration Examples for Configuration File Management Using SNMP
Configuration Examples for Configuration File Management Using SNMP Keywords: SNMP, NMS, agent, FTP, TFTP, current configuration, configuration file for the next system startup Abstract: Net-SNMP is a
More informationHP 5130 EI Switch Series
HP 5130 EI Switch Series IRF Command Reference Part number: 5998-5478a Software version: Release 31xx Document version: 6W100-20150731 Legal and notice information Copyright 2015 Hewlett-Packard Development
More informationDownload and Backup Configuration Files on the WAP131 and WAP351
Article ID: 5068 Download and Backup Configuration Files on the WAP131 and WAP351 Objective The WAP s configuration files contain all of the information about the WAP s settings. The WAP131 and WAP351
More informationCommand Manual QinQ-BPDU Tunneling H3C S3610&S5510 Series Ethernet Switches. Table of Contents
Table of Contents Table of Contents... 1-1 1.1 QinQ Configuration Commands... 1-1 1.1.1 mac-mirroring... 1-1 1.1.2 raw-vlan-id inbound... 1-2 1.1.3 qinq enable... 1-3 1.1.4 qinq ethernet-type... 1-4 1.1.5
More informationHP 5920 & 5900 Switch Series
HP 5920 & 5900 Switch Series IRF Command Reference Part number: 5998-2881 Software version: Release2207 Document version: 6W100-20121130 Legal and notice information Copyright 2012 Hewlett-Packard Development
More informationDES-3528/52 Series Firmware Release Notes
: Prom Code : v1.00.b007 Published: 2009/3/20 These release notes include important information about D-Link switch firmware revisions. Verify that these release notes are correct for your switch: - If
More informationHP A5820X & A5800 Switch Series MPLS. Configuration Guide. Abstract
HP A5820X & A5800 Switch Series MPLS Configuration Guide Abstract This document describes the software features for the HP 5820X & 5800 Series products and guides you through the software configuration
More informationSend document comments to name List name. The range of valid values is 1 to 64.
This chapter describes the Cisco Nexus 1000V commands that begin with the letter M. mac access-list To create a MAC ACL, use the mac access-list command. To remove the MAC ACL, use the no form of this
More informationPing, tracert and system debugging commands
Contents Ping, tracert and system debugging commands 1 Ping and tracert commands 1 ping 1 ping ipv6 5 tracert 7 tracert ipv6 9 System debugging commands 10 debugging 10 display debugging 11 i Ping, tracert
More informationOperation Manual DHCP H3C S3600 Series Ethernet Switches-Release Table of Contents
Table of Contents Table of Contents Chapter 1 DHCP Overview... 1-1 1.1 Introduction to DHCP... 1-1 1.2 DHCP IP Address Assignment... 1-1 1.2.1 IP Address Assignment Policy... 1-1 1.2.2 Obtaining IP Addresses
More informationH3C MSR Router Series
H3C MSR Router Series Comware 7 OpenFlow Command Reference New H3C Technologies Co., Ltd. http://www.h3c.com Software version: MSR-CMW710-R0615P08 Document version: 6W201-20180803 Copyright 2017-2018,
More information