Table of Contents 1 System Maintenance and Debugging Commands 1-1
|
|
- Dominic Gallagher
- 5 years ago
- Views:
Transcription
1 Table of Contents 1 System Maintenance and Debugging Commands 1-1 System Maintenance Commands 1-1 ping 1-1 ping ipv6 1-5 tracert 1-6 tracert ipv6 1-7 System Debugging Commands 1-8 debugging 1-8 display debugging 1-9 i
2 1 System Maintenance and Debugging Commands System Maintenance Commands ping ping [ ip ] [ -a source-ip -c count -f -h ttl -i interface-type interface-number -m interval -n -p pad -q -r -s packet-size -t timeout -tos tos -v -vpn-instance vpn-instance-name ] * host Any view 0: Visit level ip: Supports IPv4 protocol. If this keyword is not provided, IPv4 is also supported. -a source-ip: Specifies the source IP address of an ICMP echo request (ECHO-REQUEST). It must be an IP address configured on the device. If this parameter is not provided, the source IP address of an ICMP echo request is the primary IP address of the outbound interface of the request. -c count: Specifies the number of times that an ICMP echo request is sent, in the range 1 to The default value is 5. -f: Discards packets larger than the MTU of a given interface, that is, the ICMP echo request is not allowed to be fragmented. -h ttl: Specifies the TTL value for an ICMP echo request, in the range 1 to 255. The default value is i interface-type interface-number: Specifies the ICMP echo request sending interface by its type and number. If this parameter is not provided, the ICMP echo request sending interface is determined by searching the routing table or forwarding table according to the destination IP address. -m interval: Specifies the interval (in milliseconds) to send an ICMP echo request, in the range 1 to The default value is 200 ms. If a response from the destination is received within the timeout time, the interval to send the next echo request equals the actual response period plus the value of interval. If no response from the destination is received within the timeout time, the interval to send the next echo request equals the timeout value plus the value of interval. -n: Disables domain name resolution for the host argument. When this keyword is not provided, if the host argument represents the host name of the destination, the device translates host into an address. -p pad: Specifies the value of the pad field in an ICMP echo request, in hexadecimal format, 1 to 8 bits, in the range 0 to ffffffff. If the specified value is less than 8 bits, 0s are added in front of the value to extend it to 8 bits. For example, if pad is configured as 0x2f, then the packets are padded with 0x f repeatedly to make the total length of the packet meet the requirements of the device. By 1-1
3 default, the padded value starts from 0x01 up to 0xff, where another round starts again if necessary, like 0x feff01. -q: Presence of this keyword indicates that only statistics are displayed. Absence of this keyword indicates that all information is displayed. -r: Records routing information. If this keyword is not provided, routes are not recorded. -s packet-size: Specifies length (in bytes) of an ICMP echo request, in the range 20 to The default value is 56. -t timeout: Specifies the timeout value (in milliseconds) of an ICMP echo reply (ECHO-REPLY). If the source does not receive an ICMP echo reply within the timeout, it considers the ICMP echo reply timed out. The value ranges from 0 to and defaults to tos tos: Specifies type of service (ToS) of an echo request, in the range 0 to 255. The default value is 0. -v: Displays non ICMP echo reply received. If this keyword is not provided, the system does not display non ICMP echo reply. -vpn-instance vpn-instance-name: Specifies the name of an MPLS VPN instance, which is a case sensitive string of 1 to 31 characters. If an MPLS VPN instance is configured on both source and destination, when you execute the ping command, this keyword must be provided; otherwise, the ping operation fails. To check whether two nodes in an MPLS VPN can reach each other, use this keyword to specify the MPLS VPN instance to which the two nodes belong. host: IP address or host name (a string of 1 to 255 characters) of the destination. Use the ping command to verify whether the destination in an IP network is reachable, and to display the related statistics. With the ping command executed, the source sends an ICMP echo request to the destination: If the destination name is unrecognizable, the system outputs Error: Ping: Unknown host host-name. If the source receives an ICMP echo reply from the destination within the timeout, the system outputs the related information of the reply. If the source does not receive an ICMP echo reply from the destination within the timeout, the system outputs Request time out. To use the name of the destination host to perform the ping operation, you must configure Domain Name System (DNS) on the device first; otherwise, the ping operation fails. In addition, you must use the command in the form of ping ip ip instead of ping ip if the destination name is a key word, such as ip. Only the directly connected segment address can be pinged if the outbound interface is specified with the -i argument. To abort the ping operation during the execution of the command, press Ctrl+C. # Check whether the device with an IP address of is reachable. <Sysname> ping PING : 56 data bytes, press CTRL_C to break Reply from : bytes=56 Sequence=1 ttl=254 time=205 ms Reply from : bytes=56 Sequence=2 ttl=254 time=1 ms 1-2
4 Reply from : bytes=56 Sequence=3 ttl=254 time=1 ms Reply from : bytes=56 Sequence=4 ttl=254 time=1 ms Reply from : bytes=56 Sequence=5 ttl=254 time=1 ms ping statistics packet(s) transmitted 5 packet(s) received 0.00% packet loss round-trip min/avg/max = 1/41/205 ms The above information shows the following: The destination was reachable. All ICMP echo requests sent by the source got responses. The minimum time, average time, and maximum time for the packet s roundtrip time are 1 ms, 41 ms, and 205 ms respectively. # Check whether the device with an IP address of is reachable. Only the check results are displayed. <Sysname> ping -q PING : 56 data bytes, press CTRL_C to break ping statistics packet(s) transmitted 4 packet(s) received 20.00% packet loss round-trip min/avg/max = 1/12/29 ms # Check whether the device with an IP address of is reachable. The route information is required to be displayed. <Sysname> ping -r PING : 56 data bytes, press CTRL_C to break Reply from : bytes=56 Sequence=1 ttl=254 time=53 ms Reply from : bytes=56 Sequence=2 ttl=254 time=1 ms Reply from : bytes=56 Sequence=3 ttl=254 time=1 ms Reply from : bytes=56 Sequence=4 ttl=254 time=1 ms
5 Reply from : bytes=56 Sequence=5 ttl=254 time=1 ms ping statistics packet(s) transmitted 5 packet(s) received 0.00% packet loss round-trip min/avg/max = 1/11/53 ms The above information shows the following: The destination was reachable. The route is <-> { ; } <-> Table 1-1 ping command output description Field PING Check whether the device with IP address is reachable 56 data bytes Number of data bytes in each ICMP echo request press CTRL_C to break Reply from : bytes=56 Sequence=1 ttl=255 time=1 ms During the execution of the command, you can press Ctrl+C to abort the ping operation. Received the ICMP reply from the device whose IP address is If no reply is received during the timeout period, Request time out will be displayed. bytes= indicates the number of data bytes in the ICMP reply. Sequence= indicates the packet sequence, used to determine whether a segment is lost, disordered or repeated. ttl= indicates the TTL value in the ICMP reply. time= indicates the response time. The routers through which the ICMP echo request passed. They are displayed in inversed order, that is, the router with a smaller distance to the destination is displayed first ping statistics --- Statistics on data received and sent in the ping operation 5 packet(s) transmitted Number of ICMP echo requests sent 5 packet(s) received Number of ICMP echo requests received 0.00% packet loss Percentage of packets not responded to the total packets sent round-trip min/avg/max = 0/4/20 ms Minimum/average/maximum response time, in ms. The field is not available for failed ping attempts in an IPv4 network. In an IPv6 network, however, the field is available and set to 0/0/0 ms. 1-4
6 ping ipv6 ping ipv6 [ -a source-ipv6 -c count -m interval -s packet-size -t timeout ] * host [ -i interface-type interface-number ] Any view 0: Visit level -a source-ipv6: Specifies the source IPv6 address of an ICMP echo request. It must be a legal IPv6 address configured on the device. If this parameter is not provided, the source IPv6 address of an ICMP echo request is the primary IPv6 address of the outbound interface of the request. -c count: Specifies the number of times that an ICMPv6 echo request is sent, in the range 1 to The default value is 5. -m interval: Specifies the interval (in milliseconds) to send an ICMPv6 echo reply, in the range 1 to The default value is 200 ms. If a response from the destination is received within the timeout time, the interval to send the next echo request equals the actual response period plus the value of interval. If no response from the destination is received within the timeout time, the interval to send the next echo request equals the timeout value plus the value of interval. -s packet-size: Specifies length (in bytes) of an ICMPv6 echo request, in the range 20 to It defaults to 56. -t timeout: Specifies the timeout value (in milliseconds) of an ICMPv6 echo reply, in the range 0 to It defaults to host: IPv6 address or host name of the destination, a string of 1 to 46 characters. -i interface-type interface-number: Specifies an outbound interface by its type and number. This parameter can be used only in case that the destination address is the link local address and the specified outbound interface must have a link local address (For the configuration of link local address, see IPv6 Basics in the IP Services Volume). If this parameter is not provided, the ICMP echo request sending interface is determined by searching the routing table or forwarding table according to the destination IP address. Use the ping ipv6 command to verify whether an IPv6 address is reachable, and display the corresponding statistics. You must use the command in the form of ping ipv6 ipv6 instead of ping ipv6 if the destination name is an ipv6 name. To abort the ping ipv6 operation during the execution of the command, press Ctrl+C. # Verify whether the IPv6 address 2001::1 is reachable. <Sysname> ping ipv6 2001::1 1-5
7 PING 2001::2 : 56 data bytes, press CTRL_C to break Reply from 2001::1 bytes=56 Sequence=1 hop limit=64 time = 62 ms Reply from 2001::1 bytes=56 Sequence=2 hop limit=64 time = 26 ms Reply from 2001::1 bytes=56 Sequence=3 hop limit=64 time = 20 ms Reply from 2001::1 bytes=56 Sequence=4 hop limit=64 time = 4 ms Reply from 2001::1 bytes=56 Sequence=5 hop limit=64 time = 16 ms ::2 ping statistics packet(s) transmitted 5 packet(s) received 0.00% packet loss round-trip min/avg/max = 4/25/62 ms The hop limit field in this prompt information has the same meaning as the ttl field in the prompt information displayed by the IPv4 ping command, indicating the TTL value in the ICMPv6 echo request. For the description on other fields, see Table 1-1. tracert tracert [ -a source-ip -f first-ttl -m max-ttl -p port -q packet-number -vpn-instance vpn-instance-name -w timeout ] * host Any view 0: Visit level -a source-ip: Specifies the source IP address of a tracert packet. It must be a legal IP address configured on the device. If this parameter is not provided, the source IP address of an ICMP echo request is the primary IP address of the outbound interface of the tracert packet. -f first-ttl: Specifies the first TTL, that is, the allowed number of hops for the first packet, in the range 1 to 255. It defaults to 1 and must be less than the maximum TTL. -m max-ttl: Specifies the maximum TTL, that is, the maximum allowed number of hops for a packet, in the range 1 to 255. It defaults to 30, and must be greater than the first TTL. -p port: Specifies the UDP port number of the destination, in the range 1 to The default value is You do not need to modify this parameter. -q packet-number: Specifies the number of probe packets sent each time, in the range 1 to The default value is 3. -vpn-instance vpn-instance-name: Specifies the name of an MPLS VPN instance, which is a string of 1 to 31 characters. 1-6
8 -w timeout: Specifies the timeout time of the reply packet of a probe packet, in the range 1 to 65535, in milliseconds. The default value is 5000 ms. host: IP address or host name (a string of 1 to 255 characters) of the destination. Use the tracert command to trace the path the packets traverse from source to destination. After having identified network failure with the ping command, use the tracert command to determine the failed node(s). Output information of the tracert command includes IP addresses of all the Layer 3 devices the packets traverse from source to destination. If a device times out, "* * *" will be displayed. To abort the tracert operation during the execution of the command, press Ctrl+C. # Display the path the packets traverse from source to destination with an IP address of <Sysname> system-view [Sysname] ip ttl-expires enable [Sysname] ip unreachables enable [Sysname] tracert traceroute to ( ) 30 hops max,40 bytes packet, press CTRL_C to break ms 425 ms 30 ms ms 470 ms 80 ms Table 1-2 tracert command output description Field traceroute to ( ) hops max bytes packet press CTRL_C to break ms 425 ms 30 ms Display the route the IP packets traverse from the current device to the device whose IP address is Maximum number of hops of the probe packets, which can be set through the -m keyword Number of bytes of a probe packet During the execution of the command, you can press Ctrl+C to abort the tracert operation. The probe result of the probe packets whose TTL is 1, including the IP address of the first hop and the roundtrip time of three probe packets. The number of packets that can be sent in each probe can be set through the -q keyword. tracert ipv6 tracert ipv6 [ -f first-ttl -m max-ttl -p port -q packet-number -w timeout ] * host Any view 0: Visit level 1-7
9 -f first-ttl: Specifies the first TTL, that is, the allowed number of hops for the first packet, in the range 1 to 255. It defaults to 1 and must be less than the maximum TTL. -m max-ttl: Specifies the maximum TTL, that is, the maximum allowed number of hops for a packet, in the range 1 to 255. It defaults to 30 and must be greater than the first TTL. -p port: Specifies the UDP port number of the destination, in the range 1 to The default value is It is unnecessary to modify this parameter. -q packet-number: Specifies the number of probe packets sent each time, in the range 1 to 65535, defaulting to 3. -w timeout: Specifies the timeout time of the reply packet of a probe packet, in the range 1 to 65535, in milliseconds. The default value is 5000 ms. host: IPv6 address or host name of the destination, a string of 1 to 46 characters. Use the tracert ipv6 command to view the path the IPv6 packets traverse from source to destination. After having identified network failure with the ping command, you can use the tracert command to determine the failed node(s). Output information of the tracert ipv6 command includes IPv6 addresses of all the Layer 3 devices the packets traverse from source to destination. If a device times out, "* * *" will be displayed. To abort the tracert operation during the execution of the command, press Ctrl+C. # the path the packets traverse from source to destination with IPv6 address 2001::1. <Sysname> tracert ipv6 2001::1 traceroute to 2001::1 30 hops max,60 bytes packet, press CTRL_C to break ::1 3 ms <1 ms 19 ms For description on the fields in the above output information, see Table 1-2. System Debugging Commands debugging debugging { all [ timeout time ] module-name [ option ] } undo debugging { all module-name [ option ] } User view 1: Monitor level all: All debugging functions. 1-8
10 timeout time: Specifies the timeout time for the debugging all command. When all debugging is enabled, the system automatically executes the undo debugging all command after the time. The value ranges from 1 to 1440, in minutes. module-name: Module name, such as arp or device. To display the current module name, use the debugging? command. option: The debugging option for a specific module. Different modules have different debugging options in terms of their number and content. To display the currently supported options, use the debugging module-name? command. Use the debugging command to enable the debugging of a specific module. Use the undo debugging command to disable the debugging of a specific module. By default, debugging functions of all modules are disabled. Note the following: Output of the debugging information may degrade system efficiency, so you are recommended to enable the debugging of the corresponding module for diagnosing network failure, and not to enable the debugging of multiple modules at the same time. describes the default level of the debugging all command. Different debugging commands may have different default levels. You must configure the debugging, terminal debugging and terminal monitor commands first to display detailed debugging information on the terminal. For more information about the terminal debugging and terminal monitor commands, see Information Center Commands in the System Volume. Related commands: display debugging. # Enable IP packet debugging. <Sysname> debugging ip packet display debugging display debugging [ interface interface-type interface-number ] [ module-name ] Any view 1: Monitor level interface interface-type interface-number: Displays the debugging settings of the specified interface, where interface-type interface-number represents the interface type and number. module-name: Module name. Use the display debugging command to display enabled debugging functions. 1-9
11 Related commands: debugging. # Display all enabled debugging functions. <Sysname> display debugging IP packet debugging is on 1-10
Table of Contents 1 System Maintaining and Debugging Commands 1-1
Table of Contents 1 System Maintaining and Debugging Commands 1-1 System Maintaining Commands 1-1 ping 1-1 tracert 1-4 System Debugging Commands 1-6 debugging 1-6 display debugging 1-7 i 1 System Maintaining
More informationPing, tracert and system debugging commands
Contents Ping, tracert and system debugging commands 1 Ping and tracert commands 1 ping 1 ping ipv6 5 tracert 7 tracert ipv6 9 System debugging commands 10 debugging 10 display debugging 11 i Ping, tracert
More informationContents. Ping, tracert, and system debugging commands 1 debugging 1 display debugging 2 ping 2 ping ipv6 5 tracert 7 tracert ipv6 9
Contents Ping, tracert, and system debugging commands 1 debugging 1 display debugging 2 ping 2 ping ipv6 5 tracert 7 tracert ipv6 9 i Ping, tracert, and system debugging commands debugging Syntax Default
More informationContents. Ping, tracert, and system debugging commands 1. debugging 1 display debugging 1 ping 2 ping ipv6 5 tracert 7 tracert ipv6 10
Contents Ping, tracert, and system debugging commands 1 debugging 1 display debugging 1 ping 2 ping ipv6 5 tracert 7 tracert ipv6 10 i Ping, tracert, and system debugging commands debugging Syntax Default
More informationTable of Contents 1 System Maintaining and Debugging 1-1
Table of Contents 1 System Maintaining and Debugging 1-1 System Maintaining and Debugging 1-1 Ping 1-1 Introduction 1-1 Configuring Ping 1-1 Ping Configuration Example 1-2 Tracert 1-4 Introduction 1-4
More informationHP A6600 Routers Network Management and Monitoring. Command Reference. Abstract
HP A6600 Routers Network Management and Monitoring Command Reference Abstract This document describes the commands and command syntax options available for the HP A Series products. This document is intended
More informationUsing ping, tracert, and system debugging
Contents Using ping, tracert, and system debugging 1 Ping 1 Using a ping command to test network connectivity 1 Ping example 1 Tracert 3 Prerequisites 4 Using a tracert command to identify failed or all
More informationH3C SR6600/SR6600-X Routers
H3C SR6600/SR6600-X Routers Network Management and Monitoring Command Reference Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Software version: SR6600X-CMW520-R3103 SR6602-CMW520-R3103 SR6602X_MCP-CMW520-R3103
More informationHP 5920 & 5900 Switch Series
HP 5920 & 5900 Switch Series Network Management and Monitoring Command Reference Part number: 5998-2889 Software version: Release 2210 Document version: 6W100-20131105 Legal and notice information Copyright
More informationH3C SR6600 Routers. Network Management and Monitoring. Command Reference. Hangzhou H3C Technologies Co., Ltd.
H3C SR6600 Routers Network Management and Monitoring Command Reference Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Document Version: 20100930-C-1.08 Product Version: SR6600-CMW520-R2420 Copyright
More informationHP 6125G & 6125G/XG Blade Switches
HP 6125G & 6125G/XG Blade Switches Network Management and Monitoring Command Reference Part number: 5998-3173b Software version: Release 2103 and later Document version: 6W103-20151020 Legal and notice
More informationH3C S7500E Series Ethernet Switches. Network Management and Monitoring. Configuration Guide. Hangzhou H3C Technologies Co., Ltd.
H3C S7500E Series Ethernet Switches Network Management and Monitoring Configuration Guide Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Document Version: 20100930-C-1.01 Product Version: Release
More informationH3C S5500-HI Switch Series
H3C S5500-HI Switch Series Network Management and Monitoring Command Reference Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Software version: Release 52xx Document version: 6W102-20131220 Copyright
More informationHP MSR Router Series Network Management and Monitoring
HP MSR Router Series Network Management and Monitoring Command Reference(V7) Part number: 5998-7743b Software version: CMW710-R0304 Document version: 6PW104-20150914 i Legal and notice information Copyright
More informationH3C S5500-EI & S5500-SI Switch Series
H3C S5500-EI & S5500-SI Switch Series Network Management and Monitoring Command Reference Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Software version: Release 2210 Document version: 6W100-20110915
More informationHP 6125G & 6125G/XG Blade Switches
HP 6125G & 6125G/XG Blade Switches Network Management and Monitoring Configuration Guide Part number: 5998-3162b Software version: Release 2103 and later Document version: 6W103-20151020 Legal and notice
More informationHP 6125 Blade Switch Series
HP 6125 Blade Switch Series Network Management and Monitoring Configuration Guide Part number: 5998-3162 Software version: Release 2103 Document version: 6W100-20120907 Legal and notice information Copyright
More informationHP 5120 SI Switch Series
HP 5120 SI Switch Series Network Management and Monitoring Configuration Guide Part number: 5998-1813 Software version: Release 1505 Document version: 6W102-20121111 Legal and notice information Copyright
More informationHP 5820X & 5800 Switch Series Network Management and Monitoring. Configuration Guide. Abstract
HP 5820X & 5800 Switch Series Network Management and Monitoring Configuration Guide Abstract This document describes the software features for the HP 5820X & 5800 Series products and guides you through
More informationHP 5920 & 5900 Switch Series
HP 5920 & 5900 Switch Series Network Management and Monitoring Configuration Guide Part number: 5998-2900 Software version: Release 2210 Document version: 6W100-20131105 Legal and notice information Copyright
More informationHP A5500 EI & A5500 SI Switch Series Network Management and Monitoring. Configuration Guide. Abstract
HP A5500 EI & A5500 SI Switch Series Network Management and Monitoring Configuration Guide Abstract This document describes the software features for the HP A Series products and guides you through the
More informationHP 830 Series PoE+ Unified Wired-WLAN Switch Switching Engine
HP 830 Series PoE+ Unified Wired-WLAN Switch Switching Engine Network Management and Monitoring Configuration Guide Part number: 5998-3936 Software version: 3308P26 Document version: 6W101-20130628 Legal
More informationTable of Contents 1 IPv6 Configuration IPv6 Application Configuration 2-1
Table of Contents 1 IPv6 Configuration 1-1 IPv6 Overview 1-1 IPv6 Features 1-1 Introduction to IPv6 Address 1-3 Introduction to IPv6 Neighbor Discovery Protocol 1-5 Introduction to IPv6 DNS 1-8 Protocols
More informationH3C S7500E-X Switch Series
H3C S7500E-X Switch Series Comware 7 Network Management and Monitoring Command Reference New H3C Technologies Co., Ltd. http://www.h3c.com.hk Software version: S7500EX-CMW710-R7536P05 Document version:
More informationTable of Contents 1 IPv6 Configuration IPv6 Application Configuration 2-1
Table of Contents 1 IPv6 Configuration 1-1 IPv6 Overview 1-1 IPv6 Features 1-1 Introduction to IPv6 Address 1-3 Introduction to IPv6 Neighbor Discovery Protocol 1-6 Introduction to IPv6 DNS 1-8 Protocols
More informationH3C S7500E Series Ethernet Switches. Network Management and Monitoring. Configuration Guide. Hangzhou H3C Technologies Co., Ltd.
H3C S7500E Series Ethernet Switches Network Management and Monitoring Configuration Guide Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Document Version: 20100722-C-1.01 Product Version: Release
More informationH3C Access Controllers
H3C Access Controllers Network Management and Monitoring Command Reference New H3C Technologies Co., Ltd. http://www.h3c.com.hk Document version: 6W101-20171122 Copyright 2017, New H3C Technologies Co.,
More informationInternet Control Message Protocol (ICMP)
Internet Control Message Protocol (ICMP) 1 Overview The IP (Internet Protocol) relies on several other protocols to perform necessary control and routing functions: Control functions (ICMP) Multicast signaling
More informationH3C S5830V2 & S5820V2 Switch Series
H3C S5830V2 & S5820V2 Switch Series Network Management and Monitoring Command Reference Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Software version: Release 23xx Document version: 6W102-20150315
More informationHP Load Balancing Module
HP Load Balancing Module System Maintenance Configuration Guide Part number: 5998-4221 Software version: Feature 3221 Document version: 6PW100-20130326 Legal and notice information Copyright 2013 Hewlett-Packard
More informationConfigure IP SLA Tracking for IPv4 Static Routes on an SG550XG Switch
Configure IP SLA Tracking for IPv4 Static Routes on an SG550XG Switch Introduction When using static routing, you may experience a situation where a static route is active, but the destination network
More informationHP MSR Router Series. Network Management and Monitoring Configuration Guide(V7)
HP MSR Router Series Network Management and Monitoring Configuration Guide(V7) Part number: 5998-7724b Software version: CMW710-R0304 Document version: 6PW104-20150914 Legal and notice information Copyright
More informationHP FlexFabric 5930 Switch Series
HP FlexFabric 5930 Switch Series Network Management and Monitoring Configuration Guide Part number: 5998-7772b Software version: Release 241x Document version: 6W102-20171117 Legal and notice information
More informationLab 6.7.1: Ping and Traceroute
Topology Diagram Addressing Table Device Interface IP Address Subnet Mask Default Gateway R1-ISP R2-Central Eagle Server S0/0/0 10.10.10.6 255.255.255.252 N/A Fa0/0 192.168.254.253 255.255.255.0 N/A S0/0/0
More informationConfiguring IP SLAs ICMP Echo Operations
This module describes how to configure an IP Service Level Agreements (SLAs) Internet Control Message Protocol (ICMP) Echo operation to monitor end-to-end response time between a Cisco router and devices
More informationHP 6125XLG Blade Switch
HP 6125XLG Blade Switch Network Management and Monitoring Configuration Guide Part number: 5998-5376a Software version: Release 240x Document version: 6W101-20150515 Legal and notice information Copyright
More informationH3C S5820X&S5800 Switch Series
H3C S5820X&S5800 Switch Series Network Management and Monitoring Configuration Guide Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Software version: Release 1211 Document version: 6W100-20110415
More informationThe term "router" in this document refers to both routers and Layer 3 switches. Step Command Remarks. ipv6 host hostname ipv6-address
Contents Configuring IPv6 DNS 1 Overview 1 Configuring the IPv6 DNS client 1 Configuring static domain name resolution 1 Configuring dynamic domain name resolution 1 Displaying and maintaining IPv6 DNS
More informationHomework 2 TCP/IP Network Monitoring and Management
Homework 2 TCP/IP Network Monitoring and Management Hw 2 Assigned on 2015/9/1, Due 2015/9/15 Hand-In Requirement Prepare a activity/laboratory report (name it Hw4-WebSys-YourName.docx) using the ECET Lab
More informationConfiguring IP SLAs ICMP Path Jitter Operations
This document describes how to configure an IP Service Level Agreements (SLAs) Internet Control Message Protocol (ICMP) Path Jitter operation to monitor hop-by-hop jitter (inter-packet delay variance).
More informationConfiguring IPv6 DNS. Introduction to IPv6 DNS. Configuring the IPv6 DNS client. Configuring static domain name resolution
Contents Configuring IPv6 DNS 2 Introduction to IPv6 DNS 2 Configuring the IPv6 DNS client 2 Configuring static domain name resolution 2 Configuring dynamic domain name resolution 2 Displaying and maintaining
More informationInternet Protocol. Outline Introduction to Internet Protocol Header and address formats ICMP Tools CS 640 1
Internet Protocol Outline Introduction to Internet Protocol Header and address formats ICMP Tools CS 640 1 Internet Protocol Runs on all hosts in the Internet and enables packets to be routed between systems
More informationNetwork Layer (4): ICMP
1 Network Layer (4): ICMP Required reading: Kurose 4.4.3, 4.4.4 CSE 4213, Fall 2006 Instructor: N. Vlajic 2 1. Introduction 2. Network Service Models 3. Architecture 4. Network Layer Protocols in the Internet
More information(ICMP), RFC
Internet et Control o Message Protocol (ICMP), RFC 792 http://icourse.cuc.edu.cn/networkprogramming/ linwei@cuc.edu.cn Nov. 2009 Overview The IP (Internet Protocol) relies on several other protocols to
More informationLogin management commands
Contents Login management commands 1 CLI login configuration commands 1 display telnet client configuration 1 telnet 1 telnet ipv6 2 telnet server enable 3 User interface configuration commands 3 acl (user
More informationTable of Contents 1 Static Routing Configuration 1-1
Table of Contents 1 Static Routing Configuration 1-1 Introduction 1-1 Static Route 1-1 Default Route 1-1 Application Environment of Static Routing 1-2 Configuring a Static Route 1-2 Configuration Prerequisites
More informationI Commands. iping, page 2 iping6, page 4 itraceroute, page 5 itraceroute6 vrf, page 6. itraceroute vrf encap vxlan, page 12
iping, page 2 iping6, page 4 itraceroute, page 5 itraceroute6 vrf, page 6 itraceroute6 vrf encap vlan, page 7 itraceroute6 vrf encap vxlan dst-mac, page 8 itraceroute vrf, page 9 itraceroute vrf encap
More informationTable of Contents 1 Static Routing Configuration 1-1
Table of Contents 1 Static Routing Configuration 1-1 Introduction 1-1 Static Route 1-1 Default Route 1-1 Application Environment of Static Routing 1-2 Configuring a Static Route 1-2 Configuration Prerequisites
More informationConfiguring Routes on the ACE
CHAPTER2 This chapter describes how the ACE is considered a router hop in the network when it is in routed mode. In the Admin or user contexts, the ACE supports static routes only. The ACE supports up
More informationHPE FlexFabric 5940 Switch Series
HPE FlexFabric 5940 Switch Series Network Management and Monitoring Configuration Guide Part number: 5200-1026b Software version: Release 25xx Document version: 6W102-20170830 Copyright 2017 Hewlett Packard
More informationOperation Manual IP Addressing and IP Performance H3C S5500-SI Series Ethernet Switches. Table of Contents
Table of Contents Table of Contents... 1-1 1.1 IP Addressing Overview... 1-1 1.1.1 IP Address Classes... 1-1 1.1.2 Special Case IP Addresses... 1-2 1.1.3 Subnetting and Masking... 1-2 1.2 Configuring IP
More informationConfiguring IP SLAs ICMP Echo Operations
This module describes how to configure an IP Service Level Agreements (SLAs) Internet Control Message Protocol (ICMP) Echo operation to monitor end-to-end response time between a Cisco router and devices
More informationICMP (Internet Control Message Protocol)
Today s Lecture ICMP (Internet Control Message Protocol) Internet Protocols CSC / C 573 I. ICMP Overview II. ICMP rror Reporting III. ICMP Query / Response Messages IV. ICMP Message Processing Fall, 2005
More informationTable of Contents 1 IPv6 Basics Configuration 1-1
Table of Contents 1 IPv6 Basics Configuration 1-1 IPv6 Overview 1-1 IPv6 Features 1-1 Introduction to IPv6 Address 1-3 Introduction to IPv6 Neighbor Discovery Protocol 1-5 IPv6 PMTU Discovery 1-8 Introduction
More informationInternet Control Message Protocol (ICMP), RFC 792. Prof. Lin Weiguo Copyleft 2009~2017, School of Computing, CUC
Internet Control Message Protocol (ICMP), RFC 79 Prof Lin Weiguo Copyleft 009~07, School of Computing, CUC Oct 07 Overview } The IP (Internet Protocol) relies on several other protocols to perform necessary
More informationConfiguring IP SLAs LSP Health Monitor Operations
Configuring IP SLAs LSP Health Monitor Operations This module describes how to configure an IP Service Level Agreements (SLAs) label switched path (LSP) Health Monitor. LSP health monitors enable you to
More informationTroubleshooting Tools
Troubleshooting Tools An overview of the main tools for verifying network operation from a host Fulvio Risso Mario Baldi Politecnico di Torino (Technical University of Turin) see page 2 Copyright Notice
More informationOperation Manual IPv6 H3C S3610&S5510 Series Ethernet Switches Table of Contents. Table of Contents
Operation Manual IPv6 Table of Contents Table of Contents Chapter 1 IPv6 Basics Configuration... 1-1 1.1 IPv6 Overview... 1-1 1.1.1 IPv6 Features... 1-2 1.1.2 Introduction to IPv6 Address... 1-3 1.1.3
More informationIPv6 ND Configuration Example
IPv6 ND Configuration Example Keywords: IPv6 ND Abstract: This document describes the application environment and typical configuration of IPv6 ND. Acronyms: Acronym Full spelling ARP FIB Address Resolution
More informationset active-probe (PfR)
set active-probe (PfR) set active-probe (PfR) To configure a Performance Routing (PfR) active probe with a forced target assignment within a PfR map, use the set active-probe command in PfR map configuration
More informationELEC / COMP 177 Fall Some slides from Kurose and Ross, Computer Networking, 5 th Edition
ELEC / COMP 177 Fall 2011 Some slides from Kurose and Ross, Computer Networking, 5 th Edition One of the core protocols in the Internet Primarily used to communicate errors among routers and hosts IP datagram
More informationLab Troubleshooting Using traceroute Instructor Version 2500
Lab 9.3.4 Troubleshooting Using traceroute Instructor Version 2500 294-833 CCNA 2: Routers and Routing Basics v 3.1 - Lab 9.3.4 Copyright 2003, Cisco Systems, Inc. Objective Use the traceroute Cisco IOS
More informationEach ICMP message contains three fields that define its purpose and provide a checksum. They are TYPE, CODE, and CHECKSUM fields.
IP address ICMP Each ICMP message contains three fields that define its purpose and provide a checksum. They are TYPE, CODE, and CHECKSUM fields. The TYPE field identifies the ICMP message, the CODE field
More informationHP 6125 Blade Switch Series
HP 6125 Blade Switch Series Layer 3 - IP Services Configuration Guide Part number: 5998-3156 Software version: Release 2103 Document version: 6W100-20120907 Legal and notice information Copyright 2012
More informationProblems of IP. Unreliable connectionless service. Cannot acquire status information from routers and other hosts
Chapter 09 ICMP Problems of IP Unreliable connectionless service Best effort service IP datagrams are discarded If destination is not found If TTL becomes 0 If reassembly timer expires Cannot acquire status
More informationTable of Contents 1 Static Routing Configuration 1-1
Table of Contents 1 Static Routing Configuration 1-1 Introduction 1-1 Static Route 1-1 Default Route 1-1 Application Environment of Static Routing 1-2 Configuring a Static Route 1-2 Configuration Prerequisites
More informationRef: A. Leon Garcia and I. Widjaja, Communication Networks, 2 nd Ed. McGraw Hill, 2006 Latest update of this lecture was on
IP Version 4 (IPv4) Header (Continued) Identification (16 bits): One of the parameters of any network is the maximum transmission unit (MTU) parameter. This parameter specifies the maximum size of the
More informationConfiguring IP SLAs UDP Echo Operations
This module describes how to configure an IP Service Level Agreements (SLAs) User Datagram Protocol (UDP) Echo operation to monitor end-to-end response time between a Cisco device and devices using IPv4
More informationHPE FlexNetwork 5510 HI Switch Series
HPE FlexNetwork 5510 HI Switch Series Layer 3 IP Services Command Reference Part number: 5200-0078b Software version: Release 11xx Document version: 6W102-20171020 Copyright 2015, 2017 Hewlett Packard
More informationChapter 4: outline. 4.5 routing algorithms link state distance vector hierarchical routing. 4.6 routing in the Internet RIP OSPF BGP
Chapter 4: outline 4.1 introduction 4.2 virtual circuit and datagram networks 4.3 what s inside a router 4.4 IP: Internet Protocol datagram format IPv4 addressing ICMP 4.5 routing algorithms link state
More informationStep 2. Manual configuration of global unicast and link-local addresses
Lab: ICMPv6 and ICMPv6 Neighbor Discovery CIS 116 IPv6 Fundamentals Enter your answers to the questions in this lab using Canvas Quiz DHCPv6 Lab. Part 1: Setup Step 1. Basics a. Log into NetLab: ccnp.bayict.cabrillo.edu
More informationH
H12-711 Number: H12-711 Passing Score: 600 Time Limit: 120 min File Version: 1.0 Exam A QUESTION 1 The network administrator wants to improve the performance of network transmission, what steps can the
More informationHPE 5920 & 5900 Switch Series
HPE 5920 & 5900 Switch Series Layer 3 IP Services Command Reference Part number: 5998-6643t Software version: Release 2422P01 Document version: 6W101-20171030 Copyright 2016, 2017 Hewlett Packard Enterprise
More informationFACULTY OF ENGINEERING. Lab Experiment
FACULTY OF ENGINEERING ECE2056 Data Communications and Networking Lab Experiment DCN1: Network Setup and Study Using Routers Last revised: 20-11- 2015 Revised by: GVT Learning Outcome: Pre- Requisite:
More informationConfiguring IP SLAs ICMP Path Echo Operations
This module describes how to configure an IP Service Level Agreements (SLAs) Internet Control Message Protocol (ICMP) Path Echo operation to monitor end-to-end and hop-by-hop response time between a Cisco
More informationICS 451: Today's plan
ICS 451: Today's plan ICMP ping traceroute ARP DHCP summary of IP processing ICMP Internet Control Message Protocol, 2 functions: error reporting (never sent in response to ICMP error packets) network
More informationConfiguring IP SLAs ICMP Path Echo Operations
This module describes how to configure an IP Service Level Agreements (SLAs) Internet Control Message Protocol (ICMP) Path Echo operation to monitor end-to-end and hop-by-hop response time between a Cisco
More informationConfiguring IP SLAs UDP Jitter Operations
This document describes how to configure an IP Service Level Agreements (SLAs) UDP jitter operation to analyze round-trip delay, one-way delay, one-way jitter, one-way packet loss, and connectivity in
More informationConfiguring IP SLAs TCP Connect Operations
This module describes how to configure an IP Service Level Agreements (SLAs) TCP Connect operation to measure the response time taken to perform a TCP Connect operation between a Cisco router and devices
More informationIntroduction to Internetworking
Introduction to Internetworking Introductory terms Communications Network Facility that provides data transfer services An internet Collection of communications networks interconnected by bridges and/or
More informationContents. Configuring a default route 1 Introduction to default routes 1
Contents Configuring static routing 1 Introduction to static routes 1 Configuring a static route 1 Configuration prerequisites 1 Configuration procedure 1 Configuring BFD for static routes 2 BFD control
More informationHomework 2: Lab Activity TCP/IP Network Monitoring and Management
Homework 2: Lab Activity TCP/IP Network Monitoring and Management Hw 2 Assigned on 2017/8/29, Due 2017/9/7 Hand-In Requirement Prepare a activity/laboratory report (name it Hw2-WebSys-YourName.docx) using
More informationHPE FlexFabric 7900 Switch Series
HPE FlexFabric 7900 Switch Series Layer 3 IP Services Command Reference Part number: 5200-0982a Software version: Release 2150 and later Document version: 6W101-20170622 Copyright 2016, 2017 Hewlett Packard
More informationMPLS Ping and Traceroute for BGP and IGP Prefix-SID
MPLS Ping and Traceroute for BGP and IGP Prefix-SID MPLS Ping and Traceroute operations for Prefix SID are supported for various BGP and IGP scenarios, for example: Within an IS-IS level or OSPF area Across
More informationICMP Computer Networks Lab Lab Course Number: Lab Course Name: Computer Networks (A) 3. Lab Name: ICMP
112039 Computer Networks Lab - 3 ICMP 1. Lab Course Number: 112039 2. Lab Course Name: Computer Networks (A) 3. Lab Name: ICMP 4. Lab Overview: In this lab, we ll investigate the ICMP protocol; examine
More informationHP FlexFabric 5930 Switch Series
HP FlexFabric 5930 Switch Series Layer 3 IP Services Command Reference Part number: 5998-4568 Software version: Release 2406 & Release 2407P01 Document version: 6W101-20140404 Legal and notice information
More informationExperiment No: Group B_4
Experiment No: Group B_4 R (2) N (5) Oral (3) Total (10) Dated Sign Problem Definition: Study and perform Linux networking commands emulation using Python or C++. 1.1Prerequisite: Basics of Networking.
More informationICS 351: Networking Protocols
ICS 351: Networking Protocols IP packet forwarding application layer: DNS, HTTP transport layer: TCP and UDP network layer: IP, ICMP, ARP data-link layer: Ethernet, WiFi 1 Networking concepts each protocol
More informationLab Assignment 4 ECE374 Spring Posted: 03/22/18 Due: 03/29/18. In this lab, we ll take a quick look at the ICMP and IP protocols.
Lab Assignment 4 ECE374 Spring 2018 Posted: 03/22/18 Due: 03/29/18 In this lab, we ll take a quick look at the ICMP and IP protocols. Whenever possible you should hand in Wireshark screenshots that you
More informationCS 356: Computer Network Architectures. Lecture 10: IP Fragmentation, ARP, and ICMP. Xiaowei Yang
CS 356: Computer Network Architectures Lecture 10: IP Fragmentation, ARP, and ICMP Xiaowei Yang xwy@cs.duke.edu Overview Homework 2-dimension parity IP fragmentation ARP ICMP Fragmentation and Reassembly
More informationTable of Contents 1 IPv6 Configuration IPv6 Application Configuration 2-1
Table of Contents 1 IPv6 Configuration 1-1 IPv6 Overview 1-1 IPv6 Features 1-1 Introduction to IPv6 Address 1-2 Introduction to IPv6 Neighbor Discovery Protocol 1-5 Introduction to ND Snooping 1-7 Introduction
More informationIPv4 and IPv6 Commands
This module describes the Cisco IOS XR software commands used to configure the IPv4 and IPv6 commands for Broadband Network Gateway (BNG) on the Cisco ASR 9000 Series Router. For details regarding the
More informationHPE FlexNetwork 5510 HI Switch Series
HPE FlexNetwork 5510 HI Switch Series Layer 3 IP Services Command Reference Part number: 5200-3837 Software version: Release 13xx Document version: 6W100-20170315 Copyright 2015, 2017 Hewlett Packard Enterprise
More informationThe Traceroute Command in MPLS
The Traceroute Command in MPLS Document ID: 26585 Contents Introduction Prerequisites Requirements Components Used Conventions Normal traceroute Command MPLS traceroute Command no mpls ip propagate ttl
More informationAccess Rules. Controlling Network Access
This chapter describes how to control network access through or to the ASA using access rules. You use access rules to control network access in both routed and transparent firewall modes. In transparent
More informationTable of Contents 1 DNS Configuration 1-1
Table of Contents 1 DNS Configuration 1-1 DNS Overview 1-1 Static Domain Name Resolution 1-1 Dynamic Domain Name Resolution 1-1 Configuring Domain Name Resolution 1-3 Configuring Static Domain Name Resolution
More informationChecking Port Status and Connectivity
CHAPTER 5 This chapter describes how to check switch port status and connectivity on the Catalyst 4500 series switch. This chapter includes the following major sections: Checking Module Status, page 5-1
More informationOperation Manual ARP H3C S5500-SI Series Ethernet Switches. Table of Contents
Table of Contents Table of Contents... 1-1 1.1 ARP Overview... 1-1 1.1.1 ARP Function... 1-1 1.1.2 ARP Message Format... 1-1 1.1.3 ARP Address Resolution Process... 1-2 1.1.4 ARP Mapping Table... 1-3 1.2
More informationAisyatul Karima Jarkom Lanjut - Week 3 LOGO.
Network Analysis Tool Aisyatul Karima - 2012 Jarkom Lanjut - Week 3 www.themegallery.com Standar Kompetensi Pada akhir semester, mahasiswa mampu merancang, mengimplementasikan dan menganalisa sistem jaringan
More informationUsing Segment Routing OAM
Segment Routing Operations, Administration, and Maintenance (OAM) helps service providers to monitor label-switched paths (LSPs) and quickly isolate forwarding problems to assist with fault detection and
More information