Lecture (02) Switch remote configuration peer2peer star network clients/server star network Traffic analysis using Packet Tracer
|
|
|
- Amy McCarthy
- 5 years ago
- Views:
Transcription
1 Lecture (02) Switch remote configuration peer2peer star network clients/server star network Traffic analysis using Packet Tracer Dr. Ahmed M. ElShafee ١ Topology ٢
2 Preparation ٣ Commands summery ٤ enabl config t hostname FL01-R01-SW01 banner motd #Hello & Welcome to Practical Applications on Networl - Lecture 03# interface vlan 1 ip address no shutdown end enabl config t line vty 0 4 password cisco login end copy running-config startup-config reload
3 PC0 item Configuration Gateway - DNS - Port status On Band width Auto Duplex Auto IP Mask ٥ 2.1 Switch remote configuration ٦
4 set line console password enable config t line console 0 password cisco login End copy runningconfig startupconfig reload ٧ set the privilege mode password enable config t enable password cisco End disable enable ٨
5 Test remote configuration ٩ Set secret password config t enable secret password cisco end disable enable ١٠
6 Commands Summery enable config t line console 0 password cisco login enable password cisco enable secret cisco1 copy running-config startup-config reload ١١ 2.2 peer2peer star network ١٢
7 Topology ١٣ Configuring interface enable config t interface fa0/1 speed 100 duplex full no sh description Floor01-Rack01-Room-1101 end ١٤
8 ١٥ Update PC1 configuration PC1 item Configuration Gateway - DNS - Port status On Band width 100 Duplex Full IP Mask ١٦
9 Show MAC address table information show mac address-table Ping show mac address-table ١٧ Configure range of interfaces config t interface range fa0/1-6 speed 100 duplex full end ١٨
10 item Configuration item Configuration Gateway Gateway PC1 DNS Port status On Band width 100 Duplex Full PC2 DNS Port status On Band width 100 Duplex Full IP IP Mask Mask item Configuration item Gateway Gateway PC3 DNS Port status On Band width 100 Duplex Full PC4 DNS Port status On Band width 100 Duplex Full IP IP ١٩ Mask Mask item Configuration item Configuration Gateway Gateway PC5 DNS Port status On Band width 100 Duplex Full PC6 DNS Port status On Band width 100 Duplex Full IP IP Mask Mask ٢٠
11 Show MAC address table information show mac address-table Ping Ping Ping Ping Ping Ping show mac address-table ٢١ Commands Summery enable config t interface fa0/1 speed 100 duplex full no sh description Floor01-Rack01-Room-1101 end ping show mac address-table show mac address-table Ping Ping Ping Ping Ping show mac address-table copy running-config startup-config reload Config t interface range fa0/1-6 speed 100 duplex full end ٢٢
12 2.3 Clients/Server star network ٢٣ Topology ٢٤
13 Server Configuration ٢٥ ٢٦
14 ٢٧ ٢٨
15 ٢٩ ٣٠
16 ٣١ ٣٢
17 ٣٣ ٣٤
18 item Configuration item Configuration Gateway Gateway PC0 DNS Port status Band width Duplex On Auto Auto PC1 DNS Port status Band width Duplex On Auto Auto IP IP Mask Mask PC2 item Configuration item Gateway Gateway DNS Port status On Band width Auto Duplex Auto IP PC3 DNS Port status Band width Duplex IP Mask omputer Mask Networks ٣٥ On Auto Auto Check IP configuration of PCs ٣٦
19 Check connectivity ٣٧ Check DNC/http services ٣٨
20 ٣٩ Check service ٤٠
21 ٤١ ٤٢
22 ٤٣ ٤٤
23 ٤٥ ٤٦
24 2.4 Traffic analysis using Packet Tracer ٤٧ Traffic analysis, simple PDU ٤٨ Real time mode
25 2 1 ٤٩ 2 1 ٥٠
26 3 2 1 ٥١ Inspection / packet ٥٢ Simulation mode
27 3 2 1 ٥٣ Traffic analysis, complex PDU, ping ٥٤
28 3 2 1 ٥٥ ٥٦
29 2 1 ٥٧ ٥٨
30 Traffic analysis, complex PDU, http ٥٩ ٦٠
31 ٦١ Thanks,.. See you next week (ISA), ٦٢
Lecture (04) Using VLANs to segment LANs. Dr. Ahmed M. ElShafee. Dr. Ahmed ElShafee, ACU Spring 2014, Practical Applications in Computer Networks 4.
Lecture (04) Using VLANs to segment LANs Dr. Ahmed M. ElShafee ١ 4.0 ٢ Topology ٣ item Configuration item Configuration Gateway Gateway PC1 DNS Port status Band width Duplex On PC2 DNS Port status Band
CS IT ports switch basic configuration. Lecture (01) Introduction to 24 ports managed switches By: Dr. Ahmed ElShafee.
Lecture (01) Introduction to 24 ports managed switches By: Dr. Ahmed ElShafee CS IT Agenda 24 ports switch basic configuration Switch remote configuration peer2peer star network clients/server star network
Lecture (03) VLANs 4.0 PC2 PC1 PC4 PC3. By: Dr. Ahmed ElShafee. Topology. Dr. Ahmed ElShafee, ACU : Fall 2015, Practical App. Networks II IP
Lecture (03) VLANs By: Dr. Ahmed ElShafee 4.0 ١ Dr. Ahmed ElShafee, ACU : Fall 2015, Practical App. Networks II ٢ Topology Gateway Gateway PC1 DNS Port status Band width Duplex On PC2 DNS Port status Band
Lecture (03) VLANs. By: Dr. Ahmed ElShafee. Dr. Ahmed ElShafee, ACU : Fall 2015, Practical App. Networks II 4.0
Lecture (03) VLANs By: Dr. Ahmed ElShafee ١ Dr. Ahmed ElShafee, ACU : Fall 2015, Practical App. Networks II 4.0 ٢ Topology ٣ item Configuration item Configuration PC1 PC2 IP 10.0.2.1 IP 10.0.2.2 item Configuration
Lecture (06) Design and Configuration LAN Practicing, working on CISCO equipment. By: Dr. Ahmed ElShafee
Lecture (06) Design and Configuration LAN Practicing, working on CISCO equipment By: Dr. Ahmed ElShafee ١ Dr. Ahmed ElShafee, ACU : Fall 2015, Practical App. Networks II Part I ٢ ٣ SW01 steps firstly connect
Lecture (04) VTP Ports Security
Lecture (04) VTP Ports Security By: Dr. Ahmed ElShafee ١ Dr. Ahmed ElShafee, ACU : Fall 2015, Practical App. Networks II VTP VLAN Trucking Protocol (VTP) is a Cisco proprietary protocol that propagates
ICND1. Switch Configuration Lab. All configurations have been set to factory defaults for these labs
ICND1 Switch Configuration Lab TOPOLOGY 3xPC (hosts) 2x2950 (Layer 2 Switches) 1x3560 (Layer 3 Switch) 5x2811 (Routers, unused in this set of labs) All configurations have been set to factory defaults
Lecture (08) DHCP server L3 switch By: Dr. Ahmed ElShafee Dr. Ahmed ElShafee, ACU : Fall 2015, Practical App. Networks II
Lecture (08) DHCP server L3 switch By: Dr. Ahmed ElShafee ١ Dr. Ahmed ElShafee, ACU : Fall 2015, Practical App. Networks II Topology 01 ٢ Topology 01 4 DHCP servers ٣ G Floor F0Dest1 F0Edge1 F0AP1 R0 F0AP3
Lab 1. CLI Navigation. Scenario. Initial Configuration for R1
Lab 1 CLI Navigation This lab covers the most basic skills for accessing and using the command-line interface (CLI) on a Cisco router or switch. Many of the small, picky details of how the CLI works cannot
configuring and connecting 24
Lecture (01) configuring and connecting 24 ports switch Dr. Ahmed M. ElShafee ١ ٢ Step 1: connecting your PC to the Console Port. Open HyperTerminal software Press RETURN to get started. Switch> (User
Lecture (01) configuring and connecting 24 ports switch
Lecture (01) configuring and connecting 24 ports switch Dr. Ahmed M. ElShafee ١ ٢ Step 1: connecting your PC to the Console Port. Open HyperTerminal software Press RETURN to get started. Switch> (User
Device Interface IP Address Subnet Mask Default Gateway
Topology Diagram Addressing Table Device Interface IP Address Subnet Mask Default Gateway BRANCH HQ ISP Fa0/0 172.20.1.129 255.255.255.128 N/A S0/0/0 172.20.1.1 255.255.255.128 N/A Fa0/0 172.20.0.129 255.255.255.128
Lab Troubleshooting VTP Configuration
Lab 4.4.3 Troubleshooting VTP Configuration Topology Diagram Addressing Table Device (Hostname) Interface IP Address Subnet Mask S1 VLAN 99 172.17.99.11 255.255.255.0 S2 VLAN 99 172.17.99.12 255.255.255.0
Troubleshooting Network analysis Software communication tests and development Education. Protocols used for communication (10 seconds capture)
Lab 1 Wireshark Wireshark is an open source and free packet analyser used for many purposes, such as: Troubleshooting Network analysis Software communication tests and development Education This reports
Lab 7 Configuring Basic Router Settings with IOS CLI
Lab 7 Configuring Basic Router Settings with IOS CLI Objectives Part 1: Set Up the Topology and Initialize Devices Cable equipment to match the network topology. Initialize and restart the router and switch.
Lab Managing Router Configuration Files with Terminal Emulation Software
Lab Managing Router Configuration Files with Terminal Emulation Software Topology Addressing Table Objectives Device Interface IP Address Subnet Mask Default Gateway R1 G0/1 192.168.1.1 255.255.255.0 N/A
Lab Using the CLI to Gather Network Device Information Topology
Topology Addressing Table Objectives Device Interface IP Address Subnet Mask Default Gateway R1 G0/1 192.168.1.1 255.255.255.0 N/A Lo0 209.165.200.225 255.255.255.224 N/A S1 VLAN 1 192.168.1.11 255.255.255.0
Lab Correcting RIPv2 Routing Problems
Lab 9.4.2 Correcting RIPv2 Routing Problems e Interface IP Address Subnet Mask Default Gateway Device Host Name Interface IP Address Subnet Mask Default Gateway R1 BRANCH1 Fast Ethernet 0/0 172.16.0.1
Lab 9.6.3: EIGRP Troubleshooting Lab
Topology Diagram Addressing Table Device Interface IP Address Subnet Mask Default Gateway Fa0/0 172.18.64.1 255.255.192.0 N/A HQ S0/0/0 209.165.202.129 255.255.255.252 N/A S0/0/1 209.165.202.133 255.255.255.252
Configuration and management of Networks LAB 1 Introduction to packet tracer
LAB 1 Introduction to packet tracer Objectives: Learn Packet Tracer to design and simulate networks. Learn to create a simple LAN with two PCs using an Ethernet hub and two straight through cables to connect
Lab : Challenge OSPF Configuration Lab. Topology Diagram. Addressing Table. Default Gateway. Device Interface IP Address Subnet Mask
Topology Diagram Addressing Table Device Interface IP Address Subnet Mask Default Gateway Fa0/0 HQ S0/0/0 S0/0/1 Lo1 10.10.10.1 255.255.255.252 Fa0/0 Branch1 S0/0/0 S0/0/1 Fa0/0 Branch2 S0/0/0 S0/0/1 PC1
TELECOMMUNICATION MANAGEMENT AND NETWORKS
QUAID-E-AWAM UNIVERSITY OF ENGINEERING SCIENCE AND TECHNOLOGY, NAWABSHAH TELECOMMUNICATION MANAGEMENT AND NETWORKS LAB # 3 CONFIGURING INTERFACES OF ROUTER AND SWITCH Topology Diagram Addressing Table
Classful Address Subnet Mask Number of Hosts per Subnet (2 x 2)
LAB 1 Exercise 1- Subnetting exercises. Write the subnet, broadcast address, and valid host range for question 1 through question 6: 1. 192.168.100.25/30 2. 192.168.100.37/28 3. 192.168.100.66/27 4. 192.168.100.17/29
Skills Assessment Student Practice
Skills Assessment Student Practice Topology Assessment Objectives Part 1: Develop the IPv4 Address Scheme (15 points, 20 minutes) Part 2: Initialize and Reload Devices (10 points, 5 minutes) Part 3: Configure
PT Activity: Configuring a Zone-Based Policy Firewall (ZPF)
PT Activity: Configuring a Zone-Based Policy Firewall (ZPF) Instructor Version Topology Diagram Addressing Table Device Interface IP Address Subnet Mask Default Gateway R1 R2 R3 Fa0/1 192.168.1.1 255.255.255.0
Lab 6.4.2: Challenge Inter-VLAN Routing
Lab 6.4.2: Challenge Inter-VLAN Routing Topology Diagram Addressing Table Device (Hostname) Interface IP Address Subnet Mask Default Gateway S1 VLAN 99 192.168.99.11 255.255.255.0 192.168.99.1 S2 VLAN
Lab Configuring and Verifying Extended ACLs Topology
Topology 2015 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 1 of 8 Addressing Table Objectives Device Interface IP Address Subnet Mask Default Gateway R1 G0/1 192.168.10.1
Device Interface IP Address Subnet Mask R1 G0/ N/A
CSNB214 Packet Tracer Topology Addressing Table Device Interface IP Address Subnet Mask Default Gateway Objectives R1 G0/0 192.168.20.1 255.255.255.0 N/A S1 VLAN 10 S2 VLAN 10 G0/1 192.168.10.1 255.255.255.0
Lab : OSPF Troubleshooting Lab
Topology Diagram Addressing Table Device Interface IP Address Subnet Mask Default Gateway Fa0/0 10.10.0.1 255.255.252.0 N/A HQ S0/0/0 172.16.7.1 255.255.255.252 N/A S0/0/1 172.16.7.5 255.255.255.252 N/A
Lab 9.6.2: Challenge EIGRP Configuration Lab
Topology Diagram Addressing Table Device Interface IP Address Subnet Mask Default Gateway HQ BRANCH1 BRANCH2 PC1 PC2 PC3 Fa0/0 S0/0/0 S0/0/1 Lo1 Fa0/0 S0/0/0 S0/0/1 Fa0/0 S0/0/0 S0/0/1 NIC NIC NIC All
Lecture (01) Determining IP Routes (1)
Lecture (01) Determining IP Routes (1) By: Dr. Ahmed ElShafee ١ Dr. Ahmed ElShafee, ACU : Fall 2016, Practical App. Networks II Overview Routing is the process of determining where to send data packets
CCNA 1 Chapter 2 v5.0 Exam Answers %
CCNA 1 Chapter 2 v5.0 Exam Answers 2015 100% 1. Which two features are characteristics of flash memory? (Choose two.) Flash provides nonvolatile storage. Flash receives a copy of the IOS from RAM when
Lab Designing and Implementing a VLSM Addressing Scheme. Topology. Objectives. Background / Scenario
CSNB214 Packet Tracer Lab Designing and Implementing a VLSM Addressing Scheme Topology Objectives Part 1: Examine Network Requirements Part 2: Design the VLSM Address Scheme Part 3: Cable and Configure
CHAPTER 2 ACTIVITY
CHAPTER 2 ACTIVITY 2.1.1.1 1. CLI stands for 2. GUI stands for 3. Write the step you used to go to CLI interface on Windows 4. The OS, normally loads from a disk drive, into RAM. 5. The portion of the
Antonio Cianfrani. Packet Tracer
Antonio Cianfrani Packet Tracer Packet Tracer (1/2) Packet Tracer? Cisco Packet Tracer is a software able to emulate CISCO networking devices. Packet Tracer features: Allows to create network topologies
Lab - Troubleshooting Standard IPv4 ACL Configuration and Placement Topology
Lab - Troubleshooting Standard IPv4 ACL Configuration and Placement Topology 2016 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 1 of 8 Addressing Table Objectives
Skills Assessment Student Training
Skills Assessment Student Training Topology Assessment Objectives Part 1: Initialize Devices (6 points, 5 minutes) Part 2: Configure Device Basic Settings (33 points, 20 minutes) Part 3: Configure Switch
Lab - Configuring a Switch Management Address
Topology Addressing Table Objectives Device Interface IP Address Subnet Mask Default Gateway S1 VLAN 1 192.168.1.2 255.255.255.0 N/A PC-A NIC 192.168.1.10 255.255.255.0 N/A Part 1: Configure a Basic Network
This document is exclusive property of Cisco Systems, Inc. Permission is granted to print and copy this document for non-commercial distribution and
This document is exclusive property of Cisco Systems, Inc. Permission is granted to print and copy this document for non-commercial distribution and exclusive use by instructors in the CCNA Exploration:
Lab 5.6.2: Challenge RIP Configuration
Topology Diagram Addressing Table Device Interface IP Address Subnet Mask Default Gateway BRANCH HQ ISP PC1 PC2 PC3 Fa0/0 S0/0/0 Fa0/0 S0/0/0 S0/0/1 Fa0/0 S0/0/1 NIC NIC NIC Learning Objectives Upon completion
KIM DONNERBORG / RTS. Cisco Lab Øvelse Af Kim Donnerborg / RTS. Side 0 af 8
KIM DONNERBORG / RTS Side 0 af 8 INDHOLDSFORTEGNELSE Lab: Basic Router Configuration... 2 Topology Diagram... 2 Addressing Table... 2 Learning Objectives... 2 Scenario... 2 Task 1: Cable the Network....
Dr. Tom Hicks. Computer Science Department Trinity University
Dr. Tom Hicks Computer Science Department Trinity University 1 1 Remote Desktop Into CS-X That Contains Your Switch? Open Putty To Your Switch 2 What is the Command To Go Into Privilege Mode DO IT! enable
Default Gateway Fa0/ N/A. Device Interface IP Address Subnet Mask
Felix Rohrer Topology Addressing Table Device Interface IP Address Subnet Mask Default Gateway Fa0/1 10.0.0.1 255.255.255.128 N/A S0/0/0 172.16.0.1 255.255.255.252 N/A S0/0/1 172.16.0.9 255.255.255.252
CCNA 1 Final Exam Answers UPDATE 2012 eg.1
CCNA 1 Final Exam Answers UPDATE 2012 eg.1 January 12th, 2012AdminLeave a commentgo to comments Which of the following are the address ranges of the private IP addresses? (Choose three.) 10.0.0.0 to 10.255.255.255
CCNA 1 Chapter 2 v5.0 Exam Answers 2013
CCNA 1 Chapter 2 v5.0 Exam Answers 2013 1. Refer to the exhibit. A switch was configured as shown. A ping to the default gateway was issued, but the ping was not successful. Other switches in the same
Lab - Building a Switch and Router Network
Topology Addressing Table Device Interface IP Address Subnet Mask Default Gateway G0/0 192.168.0.1 N/A G0/1 192.168.1.1 N/A PC-A NIC 192.168.1.3 192.168.1.1 PC-B NIC 192.168.0.3 192.168.0.1 R1 Objectives
Lab Configuring Switch Security Features Topology
Topology Addressing Table Objectives Device Interface IP Address Subnet Mask Default Gateway R1 G0/1 172.16.99.1 255.255.255.0 N/A S1 VLAN 99 172.16.99.11 255.255.255.0 172.16.99.1 PC-A NIC 172.16.99.3
Lab Configuring Basic RIPv2 (Solution)
(Solution) Topology 2017 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 1 of 15 Addressing Table Objectives Device Interface IP Address Subnet Mask Default Gateway
Lab Configuring 802.1Q Trunk-Based Inter-VLAN Routing Topology
Topology 2016 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 1 of 7 Addressing Table Device Interface IP Address Subnet Mask Default Gateway R1 G0/1.1 192.168.1.1
Network II Lab 03 Part 01: Ping command in simula on mode
Network II Lab 03 Part 01: Ping command in simula on mode 1. Open the file saved from the previous lab. [Dr. Ahmed ElShafee, ACU Fall 2011, Network II] 1 / 18 2. add simple packet from client to server
Lab 2.8.2: Challenge Static Route Configuration
Topology Diagram Addressing Table Device Interface IP Address Subnet Mask Default Gateway BRANCH HQ ISP PC1 PC2 Web Server Fa0/0 S0/0/0 Fa0/0 S0/0/0 S0/0/1 209.165.201.2 255.255.255.252 Fa0/0 209.165.200.225
Department Of Computer Science
Department Of Computer Science Laboratory Manual Prepared By: Muhammad Nouman Farooq Lecturer and Course Coordinator Course: Computer Communication and Networks (CS-205) Page 1 of 43 Table of Contents
CCNA Semester 2 labs. Labs for chapters 2 10
CCNA Semester 2 labs Labs for chapters 2 10 2.2.2.5 Lab - Configuring IPv4 Static and Default Routes 2.3.2.4 Lab - Troubleshooting Static Routes 3.2.1.9 Lab - Configuring Basic RIPv2 5.2.2.9 Lab - Configuring
Chapter 10 - Configure ASA Basic Settings and Firewall using ASDM
Chapter 10 - Configure ASA Basic Settings and Firewall using ASDM This lab has been updated for use on NETLAB+ Topology Note: ISR G1 devices use FastEthernet interfaces instead of GigabitEthernet interfaces.
CCNA2 Chapter 1 Practice
CCNA2 Chapter 1 Practice Where should a crossover UTP cable be used? (Choose 2) To connect two PCs together directly. To connect a router to an Ethernet switch. To connect a PC to an Ethernet switch. To
Router pod documentation
Router pod documentation Note: DO NOT USE COPY RUNNING STARTUP, as this may reset the privileged password. If you change the privileged password, and save the configuration, please tell your lecturer as
CCNA 1 Final Exam Answers UPDATE 2012 eg.2
CCNA 1 Final Exam Answers UPDATE 2012 eg.2 January 12th, 2012AdminLeave a commentgo to comments 1. When must a router serial interface be configured with the clock rate command? when the interface is functioning
config mode: Router> enable Router# configure terminal Enter configuration commands, one per line. End with CNTL/Z.
CCNA1-CH2 2.1.1.1 OS / IOS 2.1.2.1 console (serial) / ssh / telnet 2.1.2.2 putty (teraterm / mobxterm / ) 2.1.3.1 IOS operation: console (cable + config) in packettracer 2.1.3.2 user EXEC vs Privileged
Lab Troubleshooting IP Address Issues Instructor Version 2500
Lab 4.2.6 Troubleshooting IP Address Issues Instructor Version 2500 Objective Configure two routers and two workstations in a small WAN. Troubleshoot problems introduced by incorrect configurations. Background/Preparation
Lab - Troubleshooting VLAN Configurations (Instructor Version Optional Lab)
(Instructor Version Optional Lab) Instructor Note: Red font color or gray highlights indicate text that appears in the instructor copy only. Optional activities are designed to enhance understanding and/or
Lab Configuring Basic Switch Settings (Solution)
(Solution) Topology Addressing Table Objectives Device Interface IP Address Subnet Mask Default Gateway S1 VLAN 99 192.168.1.2 255.255.255.0 192.168.1.1 PC-A NIC 192.168.1.10 255.255.255.0 192.168.1.1
Lab Troubleshooting IPv4 and IPv6 Static Routes (Instructor Version Optional Lab)
(Instructor Version Optional Lab) Instructor Note: Red font color or gray highlights indicate text that appears in the instructor copy only. Optional activities are designed to enhance understanding and/or
Education by Simulation Sequential Labs For CCNA
Education by Simulation Sequential Labs For CCNA Copyright 2004 Boson. All Rights Reserved. No part of this copyrighted document or related copyrighted software may be reproduced, transmitted, translated,
Cisco Network Academy CCNA 1 Introduction to Networks
Cisco Network Academy CCNA 1 Introduction to Networks Packet Tracer Practice with Dans Sample http://www.danscourses.com/ In this lab, you will learn how to configure the following tasks: IPv4 Addressing
Lab 7.5.3: Troubleshooting the Wireless WRT300N
Lab 7.5.3: Troubleshooting the Wireless WRT300N Topology Diagram Addressing Table Device Interface IP Address Subnet Mask Default Gateway Fa0/1.5 5.5.5.10 255.255.255.0 N/A Fa0/1.10 192.168.10.1 255.255.255.0
Lab Establishing and Verifying a Telnet Connection Instructor Version 2500
Lab 4.2.2 Establishing and Verifying a Telnet Connection Instructor Version 2500 Objective Establish a Telnet connection to a remote router. Verify that the application layer between source and destination
Lab Configuring Static Routes Instructor Version 2500
Lab 6.1.6 Configuring Static Routes Instructor Version 2500 Objective Configure static routes between routers to allow data transfer between routers without the use of dynamic routing protocols. Background/Preparation
MiPDF.COM. 3. Which procedure is used to access a Cisco 2960 switch when performing an initial configuration in a secure environment?
CCNA1 v6.0 Chapter 2 Exam Answers 2017 (100%) MiPDF.COM 1. What is the function of the kernel of an operating software? It provides a user interface that allows users to request a specific task. The kernel
CCNA 1 Chapter 6 v5.0 Exam Answers 2013
CCNA 1 Chapter 6 v5.0 Exam Answers 2013 1 After troubleshooting a router, the network administrator wants to save the router configuration so that it will be used automatically the next time that the router
CISCO SWITCH BEST PRACTICES GUIDE
CISCO SWITCH BEST PRACTICES GUIDE Table of Contents (After Clicking Link Hit HOME to Return to TOC) 1) Add Hostname... 2 2) Add Username and Password... 2 3) Create Secret Password... 2 4) Encrypt Password...
1. Which OSI layers offers reliable, connection-oriented data communication services?
CCNA 1 Practice Final Exam Answers v4.0 100% 1. Which OSI layers offers reliable, connection-oriented data communication services? application presentation session transport network 2. Refer to the exhibit.
LAB 3 Basic Switch Configuration Commands
LAB 3 Basic Switch Configuration Commands This lab explains basic switch configuration commands in detail with examples. Configuration and commands explained in this tutorial are essential commands to
EIGRP Practice Skills Assessment - Packet Tracer
CCNA Routing and Switching Scaling Networks EIGRP Practice Skills Assessment - Packet Tracer A few things to keep in mind while completing this activity: 1. Do not use the browser Back button or close
Lab Troubleshooting Basic PPP with Authentication Topology
Topology 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 1 of 8 Addressing Table Objectives Device Interface IP Address Subnet Mask Default Gateway R1 G0/1 192.168.1.1
Lab 5: Basic VLAN Configuration
Topology Diagram Addressing Table Device (Hostname) Interface IP Address Subnet Mask Default Gateway S1 VLAN 99 172.17.99.11 255.255.255.0 N/A S2 VLAN 99 172.17.99.12 255.255.255.0 N/A S3 VLAN 99 172.17.99.13
PT Activity 2.5.1: Basic Switch Configuration
Topology NOTE TO USER: This activity is a variation of Lab 2.5.1. Packet Tracer may not support all the tasks specified in the hands-on lab. This activity should not be considered equivalent to completing
Lab 1.3.2: Review of Concepts from Exploration 1 - Challenge
Lab 1.3.2: Review of Concepts from Exploration 1 - Challenge Topology Diagram Learning Objectives Upon completion of this lab, you will be able to: Create a logical topology given network requirements
Introduction to Networks: Case Study, Option 2
Introduction to Networks: Case Study, Option 2 Name: Name: Name: Academy username: Academy username: Academy username: Topology Diagram Assessment Objectives For an acceptable Case Study, the student must
Packet Tracer - Configuring Initial Switch Settings
Topology Objectives Part 1: Verify the Default Switch Configuration Part 2: Configure a Basic Switch Configuration Part 3: Configure a MOTD Banner Part 4: Save Configuration Files to NVRAM Part 5: Configure
Lab Configuring and Verifying Standard IPv4 ACLs (Instructor Version Optional Lab)
(Instructor Version Optional Lab) Instructor Note: Red font color or gray highlights indicate text that appears in the instructor copy only. Optional activities are designed to enhance understanding and/or
Lab - Configuring VLANs and Trunking
Topology Addressing Table Objectives Device Interface IP Address Subnet Mask Default Gateway S1 VLAN 1 192.168.1.11 255.255.255.0 N/A S2 VLAN 1 192.168.1.12 255.255.255.0 N/A PC-A NIC 192.168.10.3 255.255.255.0
Lab Configuring and Verifying Standard IPv4 ACLs Topology
Topology 2016 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 1 of 10 Addressing Table Objectives Device Interface IP Address Subnet Mask Default Gateway R1 G0/1 192.168.10.1
Lab - Troubleshooting ACL Configuration and Placement Topology
Topology 2015 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 1 of 8 Addressing Table Objectives Device Interface IP Address Subnet Mask Default Gateway HQ G0/1 192.168.1.1
PT Activity 4.4.1: Basic VTP Configuration
Topology Diagram Addressing Table Device Interface IP Address Subnet Mask Default Gateway S1 VLAN 99 172.17.99.11 255.255.255.0 N/A S2 VLAN 99 172.17.99.12 255.255.255.0 N/A S3 VLAN 99 172.17.99.13 255.255.255.0
Lab Exploring Cisco IOS and Configuring Basic Switch Settings
Topology Addressing Table Objectives Device Interface IP Address Subnet Mask Default Gateway S1 VLAN 99 192.168.1.2 255.255.255.0 192.168.1.1 PC-A NIC 192.168.1.10 255.255.255.0 192.168.1.1 Part 1: Cable
Lab Configuring Per-Interface Inter-VLAN Routing (Solution)
(Solution) Topology Addressing Table Objectives Device Interface IP Address Subnet Mask Default Gateway R1 G0/0 192.168.20.1 255.255.255.0 N/A G0/1 192.168.10.1 255.255.255.0 N/A S1 VLAN 10 192.168.10.11
PT Activity: Configure AAA Authentication on Cisco Routers
PT Activity: Configure AAA Authentication on Cisco Routers Instructor Version Topology Diagram Addressing Table Device Interface IP Address Subnet Mask R1 Fa0/0 192.168.1.1 255.255.255.0 S0/0/0 10.1.1.2
Lab Configuring Per-Interface Inter-VLAN Routing (Instructor Version)
(Instructor Version) Instructor Note: Red font color or Gray highlights indicate text that appears in the instructor copy only. Topology Addressing Table Objectives Device Interface IP Address Subnet Mask
Lab Configuring EtherChannel
Topology Addressing Table Objectives Device Interface IP Address Subnet Mask S1 VLAN 99 192.168.99.11 255.255.255.0 S2 VLAN 99 192.168.99.12 255.255.255.0 S3 VLAN 99 192.168.99.13 255.255.255.0 PC-A NIC
NETWORK LAB 2 Configuring Switch Desktop
Configuring Switch 1. Select the switch tab and then add a switch from the list of switches we have to the workspace, we will choose (2950-24) switch. 2. Add a number of PCs next to the switch in order
Lab Student Lab Orientation
Lab 1.1.1 Student Lab Orientation Objective In this lab, the students will complete the following tasks: Review the lab bundle equipment Understand the security pod topology Understand the pod naming and
CCNA Certification - EIGRP Configuration Lab Simulation
Free CCNA Exam Answers 2017 - Study CCNA for free Free CCNA Study Guide, Tutorials, Labs, Practice Exams. CCNA Online Training and More http://ccnav6.com CCNA Certification - EIGRP Configuration Lab Simulation
Exam E1 Copyright 2010 Thaar AL_Taiey
Exam E1 2 Exam E1 E1-1. Which of the following statements is true regarding the internetwork shown in Figure E1-1? (Select all that apply) Figure E1-1 A Sample Internetwork A. The link number 15 uses a
This document is exclusive property of Cisco Systems, Inc. Permission is granted to print and copy this document for non-commercial distribution and
This document is exclusive property of Cisco Systems, Inc. Permission is granted to print and copy this document for non-commercial distribution and exclusive use by instructors in the CCNA Exploration:
Lab - Configuring VLANs and Trunking (Solution)
(Solution) Topology Addressing Table Objectives Device Interface IP Address Subnet Mask Default Gateway S1 VLAN 1 192.168.1.11 255.255.255.0 N/A S2 VLAN 1 192.168.1.12 255.255.255.0 N/A PC-A NIC 192.168.10.3
Skills Assessment (EIGRP) Student Training Exam
Skills Assessment (EIGRP) Student Training Exam Topology Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 1 of 15 Addressing Table Device Interface IP Address Subnet
Skills Assessment Student Training Exam
Skills Assessment Student Training Exam Time: 20 minutes Given an IP address and mask of (address / mask), design an IP addressing scheme that satisfies the following requirements. Network address/mask
Chapter 10 Configure AnyConnect Remote Access SSL VPN Using ASDM
Chapter 10 Configure AnyConnect Remote Access SSL VPN Using ASDM Topology Note: ISR G1 devices use FastEthernet interfaces instead of GigabitEthernet interfaces. 2015 Cisco and/or its affiliates. All rights
Skills Assessment (EIGRP) Student Training Exam
Skills Assessment (EIGRP) Student Training Exam Topology 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 1 of 16 Addressing Table Assessment Objectives Device
Lab VTY Restriction Instructor Version 2500
Lab 11.2.6 VTY Restriction Instructor Version 2500 NOTE: The loopback entry in this graphic is not required in the lab. Objective Scenario Use the access-class and line commands to control Telnet access