System Configuration Guide (V.2)

Transcription

1 System Configuration Guide (V.2) (June / 2000) Notes P2 teamserver HS P10 PRIMERGY MS P12 PRIMERGY MS P16 PRIMERGY ES P18 PRIMERGY ES P20 PRIMERGY ES P22 External Disk Array P23 External Devices P24 Rackmount P25 Hardware P27 Index The numbers on the left hand side of each page correspond to the various options available with teamservers as follows : CPU slot RAM module slot 3.5 inch HDD Bay 5 inch Bay RS-232C PCI slot ISA slot Redundant PSU Others Key to Or And 1

2 NOTES Disk array configuration Physical pack Physical pack. A collection of physical HDDs comprising a RAID. Logical drive Logical drive. The logical drive (eg. D: ) as seen by the Operating System. Partition Partition. One of the logical access units into which a logical drive is divided. Physical pack HDD HDD HDD HDD Partition 1 Partition 2 Logical drive A Logical drive B * Drives can be divided into partitions. Logical drive C <Restrictions> (1) Each physical pack must contain the same type(size) of HDDs. (2) Maximum logical drive size is 2TB (GP5U141 / U142 / -143 / -144 / -146). (3) The number of HDDs comprising a physical pack is as shown below. RAID Level Description HDDs Capacity of logical drives RAID 0 The data is broken down into blocks, 2~8 The capacity of logical drive is same each on a separate disk drive as the capacity of connected HDD. RAID 1 Duplicates the disk and writes 2 The capacity of the logical drive is the same data onto two disks. half the capacity of connected HDD. RAID 5 The data is broken down into blocks 3~8 The capacity of each logical drive is and each blocks is written together the number of connected HDDs - 1). with parity bits on a separate disk drive. RAID 6 Duplicates the disk and broken down 3~8 The capacity of each logical drive into blocks, each on a is the half the capacity of connected on a separate disk. (RAID0+1) HDD. (GP5-143 / 144 / 146) * GP5U141 / 142: RAID6 is available with Firmware 4.04-F-56 or greater (4) The same RAID level must be use when dividing a physical pack into a number of logical drives. (5) A physical pack must contain only HDDs which are connected by the same RAID card. (6) A RAID card can support more than one physical pack. ( even if different RAID levels) (7) Same capacity HDDs connected to the same RAID Card, must also have the same r.p.m speed. 9GB 7200rpm 9GB 7200rpm 9GB 10000rpm This must be 9GB with 7200rpm HDD! RAID 2

3 NOTES Hard disk cabinet / RAID card / SCSI card GP5MS623A/GP5UR1DC5: Note: The operating System must be installed on an internal hard disk. RAID card (GP5U141 / GP5-144 / GP5-146) 1.Up to two Hard disk cabinets can be connected to one RAID card. (Up to three can be connected with one GP5-144 card) 2.When using GP5U141 in ES280/MS380, it cannot be used for both external disk array (GP5UR1DC5 / GP5MS623A) and internal disk array. 3.Internal and external array devices cannot be connected to the same channel. 4.GP5-144 / 146 can only be used with GP5-144 / 146, they cannot be mixed with GP5U141 / 142 / -143) 5.Up to two 146 can be used for internal array configuration in MS380 6.When installing three RAID cards in MS380, the internal HDD must be connected using GP5-144 RAID card (GP5U142 / GP5-143) Only for use with internal devices. Only one of these RAID cards can be used per server. SCSI card (GP5-125 / GP5-126 / GP5-127) 1.Internal and external devices cannot be connected to the same SCSI card. 2.Only one Hard disk cabinet can be connected. (Daisy chain connection is not available) Number of connectable Hard Disk Cabinets Hard Disk Node Product ES200 ES210 ES280 MS380 MS610 HS900 Hard Disk Cabinet GP5MS623A Storage System GP5UR1DC Mounting internal devices in HS900 In HS900, there are two internal HDD bays (9GB / 18GB / 36GB disks are available) Storage System (GP5UR1DC5) is required for data storage. Boot disk can be an external disk. HS900 has no internal 5" bay in chasis, so Backup cabinet (GP5UR1BC1) is required to mount backup devices. Mounting internal device (HDD / Backup device) in MS610 The following figure indicates the right adapters (Onboard SCSI channel, SCSI Card, etc.) used to mount devices in MS610 Drive Cage Conversion Kit (GP5BBU1) Applicable products MS610 - Standard Drive Cage SCSI Channel 1ch Number of mountable HDD 1inch height Hard Disk Drive x 8 (8HDDs per 1ch) - Drive Cage Conversion Kit (GP5BBU1) SCSI Channel 2ch Number of mountable HDD 1inch height Hard Disk Drive x 12 (6HDDs per 1ch x 2) 3

4 NOTES The following figure indicates the correct adapters (Onboard SCSI channel, SCSI Card, etc.) to use to mount devices in MS610 Narrow For backup device (Narrow) PRIMERGY MS610 Connection of internal HDD and internal backup devices Onboard SCSI Wide Ultra160 A For backup device (Wide) For HDD Select either of the SCSI channel Ultra160 B For HDD Internal HDD Internal backup device Connection Pattern One device is connected Two devices are connected Configuration Drive Cage SCSI Host Cable Internal HDD Narrow Wide Narrow Wide Narrow device Interface connect connect device x 2 device x 2 and device*2 device*3 Wide device Cable(X1) 1) 9GB, 7,200rpm Standard Ultra 160 Onboard SCSI (Standard 2) 18GB, 7,200rpm (8Bays) (Ultra160 A) equipment) 3) 9GB, 10,000rpm 4) 18GB, 10,000rpm 5) 36GB, 10,000rpm Wide-1 Onboard Narrow: SCSI When Drive Cable(X2) 1) 9GB, 7,200rpm Onboard Onboard Narrow-1,2 SCSI(Wide) Onboard SCSI (Narrow) Configuration Cage Ultra 160 Onboard SCSI (Standard 2) 18GB, 7,200rpm SCSI SCSI(Wide ) Onboard Conversion (Ultra160 A/B) equipment) 3) 9GB, 10,000rpm (Narrow) SCSI (Narrow) Wide-2 SCSI Card Wide: 4) 18GB, 10,000rpm Daisy chain (GP5-127) SCSI Card (GP5-127) (12Bays)*1 5) 36GB, 10,000rpm Cable(X1) 1) 9GB, 7,200rpm Standard Ultra2 Wide RAID Card (Standard 2) 18GB, 7,200rpm (8Bays) GP5-144/146 equipment) 3) 9GB, 10,000rpm (Ch0) 4) 18GB, 10,000rpm Array 5) 36GB, 10,000rpm Configuration When Drive RAID Card Cable(X2) 1) 9GB, 7,200rpm Cage Ultra2 Wide GP5-144/146 (Standard 2) 18GB, 7,200rpm Conversion (Ch0/1) equipment) 3) 9GB, 10,000rpm 4) 18GB, 10,000rpm (12Bays)*1 5) 36GB, 10,000rpm *1 Narrow connect devices: GP5UDL201/GP5UDT301/GP5USL501 *2 Wide connect devices: GP5-DT401/GP5-ML301/GP5-DL351(SCSI Cable is standard equipment with all Wide connect devices) *3 Daisy chain is not available for connection of a Wide SCSI connection device to Onboard SCSI (Wide) Mounting internal SCSI devices (HDD/Backup device) in MS380 MS380 has eight HDD bays and 18.2GB/9GB HDD (1"height) can be mounted. Up to six HDDs with 10000rpm (GP5-HDH9A/GP5-HDH87) can be mounted. (10000rpm HDD cannot be used with 7200rpm HDD) SCSI Card (GP5-127) is required if DLT unit (GP5-DL351), DAT unit (GP5-DT401) or Tape unit (GP5-ML301) is installed Only one DDS-4 (GP5-DT401) can be mounted in the lowest 5inch bay. PRIMERGY MS380 Connection of internal HDD and internal backup devices Onboard SCSI Narrow Wide A For backup device (Narrow) For HDD Wide B For HDD Internal HDD Internal backup device (Max.2) Connection Pattern One device is connected Two devices are connected Connection SCSI Host Cable Internal HDD Narrow Wide Narrow device Wide device Narrow device and Interface connect connect x 2 x 2 Wide device device*1 device*2 1)9GB,7,200rpm Cable(X1) 2)18GB,7,200rpm Wide-1 Narrow device: Ultra2 Wide Onboard SCSI (Standard 3)9GB,10,000rpm Narrow-1,2 SCSI Card Onboard SCSI Configuration equipment) 4)18GB,10,000rpm Onboard SCSI Card (GP5-127) SCSI(Narrow) SCSI(Narrow) (GP5-127) Onboard connection SCSI(Narrow) Wide-2 Wide device: RAID Card Cable(X1) 1)9GB,7,200rpm Daisy chain SCSI Card SCSI Card(GP5-127) Array Configuration Ultra2 Wide GP5U142/-144/-146(Standard 2)18GB,7,200rpm connection (GP5-127)*3 (Ch0) equipment) 3)9GB,10,000rpm 4)18GB,10,000rpm *1 Narrow connect devices: GP5UDL201/GP5UDT301/GP5USL501 *2 Wide connect devices: GP5-DT401/GP5-ML301/GP5-DL351(SCSI Cable is standard equipment with all Wide connect devices) *3 Daisy chain is not available for connection of a Wide SCSI connection device to SCSI Card (GP5-127) 4

5 NOTES Mounting internal SCSI devices (HDD/Backup device) in ES280 ES280 have four HDD bays (3hotplug and 1non hotplug) 9GB/18.2GB HDD (1"height) can be mounted. SCSI Card (GP5-125) is required if DAT unit (GP5-DT401), Tape unit (GP5-ML301) is installed PRIMERGY ES280 Connection of internal HDD and internal backup devices Onboard SCSI Narrow Wide B For backup device (Narrow) For HDD Internal HDD Internal backup device (Max:2) Connection Pattern One device is connected Two devices are connected Connection Interface Narrow connect Wide connect Narrow device and Host Internal HDD device *1 device *2 Narrow device x 2 Wide device x 2 Wide device SCSI Ultra Wide Onboard SCSI (Wide) 1)9GB,7,200rpm Narrow device: Configuration SCSI SCSI Cable (GP5-843) 2)18GB,7,200rpm Onboard SCSI Onboard SCSI (Narrow) SCSI Card (Narrow) Onboard SCSI (Narrow) SCSI Card SCSI Cable (Std.) (GP5-125 *3) SCSI Cable(Std.) SCSI Cable (Std.) (GP5-125 *3) Daisy chain with primary (SCSI Card is Wide device: Array Ultra2 Wide RAID Card 1)9GB,7,200rpm connected device required per device) SCSI Card Configuration SCSI (GP5-143) 2)18GB,7,200rpm (GP5-125) SCSI Cable(GP5-843) *1 Narrow connect devices: GP5UDT301/GP5USL501 *2 Wide connect devices: GP5-DT401/GP5-ML301(SCSI Cable is standard equipment with all Wide connect devices) *3 Daisy chain is not available for connection of a Wide SCSI device to SCSI Card(GP5-127) Mounting internal SCSI devices (HDD/Backup device) in ES210/ES200 ES210/200 have four HDD bays (three HDD bays and one 5inch bay) 9GB/18.2GB HDD (1"height) can be mounted. ES210: ES200: HDD can be connected to Onboard UltraWide SCSI. (SCSI Cable is required) SCSI Card (GP5-127) is required for Ultra2 Wide configuration. SCSI Card (GP5-127) is required to mount DDS4 backup device. SCSI Card (GP5-126) is required to mount HDD. The SCSI Card (GP5-126) is also used for connection to Narrow connect backup device (GP5UDT301/GP5USL501) with SCSI Cable (.GP5-841) SCSI Card (GP5-127) is required to mount Wide connect backup device (GP5-DT401/GP5-ML301). PRIMERGY ES210 Connection of internal HDD and internal backup devices There are two SCSI channels and two EIDE channels on the Motherboard Onboard IDE Controler Secondary EIDE Primary For CD-ROM For HDD Onboard SCSI Controler Narrow Wide For backup devide (Narrow) For HDD Internal HDD Internal backup device (Max:2) Connection Pattern One device is connected Two devices are connected Connection Interface Narrow connect Wide connect Narrow device and Host Internal HDD device *1 device *2 Narrow device x 2 Wide device x 2 Wide device SCSI Ultra Wide Onboard SCSI (Wide) 1)9GB,7,200rpm Narrow device: Configuration SCSI SCSI Cable (GP5-843) 2)18GB,7,200rpm Onboard SCSI Onboard SCSI SCSI Ultra2 Wide SCSI Card(GP5-127) 1)9GB,7,200rpm (Narrow) SCSI Card (Narrow) Configuration SCSI SCSI Cable(GP5-843) 2)18GB,7,200rpm Onboard SCSI (Narrow) SCSI Card SCSI Cable (Std.) (GP5-127 *3) SCSI Cable(Std.) IDE IDE Onboard Primary IDE 1)20.4GB, 5400rpm SCSI Cable (Std.) (GP5-127 *3) Daisy chain Configuration UltraDMA/33 with primary (SCSI Card is Wide device: Array Ultra2 Wide RAID Card 1)9GB,7,200rpm connected device required per device) SCSI Card Configuration SCSI (GP5-143) 2)18GB,7,200rpm (GP5-127) SCSI Cable(GP5-843) *1 Narrow connect devices: GP5UDT301 *2 Wide connect devices: GP5-DT401(SCSI Cable is standard equipment with all Wide connect devices) *3 Daisy chain is not available for connection of a Wide SCSI device to SCSI Card(GP5-127) 5

6 NOTES PRIMERGY ES200 Connection of internal HDD and internal backup devices There are two EIDE channels on Motherboard Onboard IDE Controler Secondary EIDE Primary For CD-ROM For HDD Internal HDD Internal backup device (Max:2) Connection Pattern One device is connected Two devices are connected Internal HDD Interface Narrow connect Wide connect Narrow device and Host Internal HDD device *1 device *2 Narrow device x 2 Wide device x 2 Wide device SCSI Card(GP5-126) SCSI Card(GP5-126) Narrow device: SCSI Ultra2 Wide SCSI Card(GP5-126) 1)9GB,7,200rpm SCSI Cable(GP5-841) SCSI Card SCSI Cable(GP5-841) SCSI Card SCSI Card(GP5-126) Configuration SCSI SCSI Cable(GP5-843) 2)18GB,7,200rpm (SCSI Card can be used (GP5-127 *3) Daisy chain with primary (GP5-127 *3) SCSI Cable(GP5-841) for both HDD and backup connected device connection (SCSI Card can be used backup device) (SCSI Card is required per for both HDD and backup IDE IDE Onboard Primary IDE 1)20.4GB, 5400rpm SCSI Card(GP5-127 ) SCSI Card(GP5-127) device) device) Configuration UltraDMA/33 SCSI Cable(GP5-840) SCSI Cable(GP5-841) Wide device: Daisy chain with primary SCSI Card Array Ultra2 Wide RAID Card 1)9GB,7,200rpm connected device (GP5-127 *3)connection Configuration SCSI (GP5-143) 2)18GB,7,200rpm (SCSI Card is required per SCSI Cable(GP5-843) device) *1 Narrow connect devices: GP5UDT301/GP5USL501 *2 Wide connect devices: GP5-DT401/GP5-ML301(SCSI Cable is standard equipment with all Wide connect devices) *3 Daisy chain is not available for connection of a Wide SCSI device to SCSI Card(GP5-127) Mountable Hard Disk Drives for each model Main unit Product Succesor HDD Interface Height Revolution Remarks Product ID ES200 Hard disk drive-9gb GP5-HD9G3 Ultra2Wide 1" 7200rpm GP5-HD9G3C Ultra2Wide 1" 7200rpm For mounting in 5" bay Hard disk drive-18gb GP5-HD8G1 Ultra2Wide 1" 7200rpm GP5-HD8G1C Ultra2Wide 1" 7200rpm For mounting in 5" bay Hard disk drive-20gb GP5-HD2E1 UltraDMA/33 1" 5400rpm IDE HDD ES210 Hard disk drive-9gb GP5-HD9G3 Ultra2Wide 1" 7200rpm GP5-HD9G3C Ultra2Wide 1" 7200rpm For mounting in 5" bay Hard disk drive-18gb GP5-HD8G1 Ultra2Wide 1" 7200rpm GP5-HD8G1C Ultra2Wide 1" 7200rpm For mounting in 5" bay Hard disk drive-20gb GP5-HD2E1 UltraDMA/33 1" 5400rpm IDE HDD ES280 Hard disk drive-9gb GP5-HD9G3 Ultra Wide 1" 7200rpm Non hotplug Hard disk drive-9gb GP5-HDH96 Ultra Wide 1" 7200rpm Hard disk drive-18gb GP5-HD8G1 Ultra Wide 1" 7200rpm Non hotplug Hard disk drive-18gb GP5-HDH83 Ultra Wide 1" 7200rpm MS380 Hard disk drive-9gb GP5-HDH96 Ultra2Wide 1" 7200rpm Hard disk drive-18gb GP5-HDH83 Ultra2Wide 1" 7200rpm Hard disk drive-9gb GP5-HDH9A Ultra2Wide 1" 10000rpm Up to six can be mounted Hard disk drive-18gb GP5-HDH87 Ultra2Wide 1" 10000rpm Up to six can be mounted MS610 Hard disk drive-9gb GP5-HDH9B Ultra160 1" 7200rpm Hard disk drive-9gb GP5-HDH9A Ultra 160 1" 10000rpm Hard disk drive-18gb GP5-HDH88 Ultra160 1" 7200rpm Hard disk drive-18gb GP5-HDH87 Ultra 160 1" 10000rpm Hard disk drive-36gb GP5-HDH63 Ultra 160 1" 10000rpm HS900 Hard disk drive-9gb GP5-HDH98T Ultra2Wide 1" 10000rpm Hard disk drive-18gb GP5-HDH85T Ultra2Wide 1" 10000rpm Hard disk drive-36gb GP5-HDH61T Ultra2Wide 1.6" 10000rpm * GP5-HDH62 is continued for additional or spair HDD in MS600 and Storage System (GP5UR1DC4) S.M.A.R.T function S.M.A.R.T. function is available in the combinations shown below: :Corresponds, x:does not correspond, -:N/A Internal Hard disk units Hard disk cabinet Standard SCSI Hard disks GP5UR1DC5/GP5MS623A Models equipment SCSI card RAID card SCSI card RAID card IDE SCSI GP5-126 GP5-127 GP5U141 GP5-143 GP5-144 GP5-146 GP5-125 GP5-127 GP5U141 GP5-144 GP5-146 ES ES ES x x - - MS MS HS Caution: Intel LANDesk Server Manager or Fujitsu Servervisor is required for SMART function 6

7 NOTES Mounting additional memory (HS900) A memory board with 16slots is standard equipment and up to 16GB memory can be mounted. When you add more than 16GB, an additional Memory Board (GP5-RB201) is required. When using two memory boards in HS900, the same memory size must be mounted on each board. Standard Memory M B M B M B M B M B M B M B M B #1 #2 #3 #13 #14 #15 #16 #5 #6 #7 #8 #9 #10 #11 #12 Additional Memory Board (GP5-RB201) M B M B M B M B M B M B M B M B #1 #2 #3 #13 #14 #15 #16 #5 #6 #7 #8 #9 #10 #11 #12 (MS610) Mount the same capacity DIMM's in units of four. (Mounting of DIMM's with different capacities or a set of less than four DIMM's is not allowed) Mount the DIMM's in ascending order of their capacity. Use DIMM slots in the order from bank A (A1 to A4) to bank D (D1 to D4) Memory Board D2 B2 C2 A2 D4 B4 C4 A4 D1 B1 C1 A1 D3 B3 C3 A3 Caution Address area of 3.5GB ~4.0GB is assigned for PCI resource, cannot be used. (MS380/ES280/ES210/ES200) The mother board has four slots for RAM modules (including base memory), install RAM modules in slot number order. (ES200 has three slots) Configuration To Order Configuration To Order (CTO) is available with PRIMERGY MS610/MS380/ES280/ES210/ES200. Products are delivered with options (HDD, Memory, Backup device, etc.) already mounted as per customer requirements. 1. How shipped [Main unit] (1) CPU+Chassis+Memory + (2) Mount option in free slots Shipment (3) Standard Memory / Drive Cage conversion 2. Applicable products for CTO (1)Main unit MS610 / MS380 / ES280 / ES210 / ES200 Storage System (GP5UR1DC5)/Hard Disk Cabinet (GP5MS623A) (2) Option (GP5BXXX) All options which are connectable with the servers above. CPU Field Upgrade Kit GP5BFG20H / GP5BFG20G GP5BFG20C / GP5BFG20B / GP5BFG205 / GP5BFG12Y Additional Memory GP5BRM4N / GP5BRM2N / GP5BRM1N / GP5BRM51N /GP5BRM25N GP5BRM51F / GP5BRM25F / GP5BRM12F / GP5BRM64F GP5BRM25H / GP5BRM12H / GP5BRM64H Standard Memory Conversion Kit GP5BRU4GA / GP5BRU2GC / GP5BRU1GF / GP5BRU51K GP5BRU25E / GP5BRU51F / GP5BRU25D Hard Disk Drive GP5BHDH63 / GP5BHDH87 / GP5BHDH9A / GP5BHDH84 / GP5BHDH97 / GP5BHD8G1 / GP5BHD9G3 / GP5BHD8G1C / GP5BHD9G3C / GP5BHD2E1 Drive Cage Conversion Kit GP5BBU1 Backup Device GP5BDT401 / GP5BDT301 / GP5BSL501 / GP5BDL201 / GP5BDL351 / GP5BML301 Redundant PSU GP5BUPU131 / GP5BUPU151 / GP5BUPU161 / GP5BUR1PU1 SCSI Card / RAID Card GP5B125 / GP5B126 / GP5B127 / GP5B128 / GP5BU141 / GP5B143 / GP5B144 / GP5B146 SCSI Cable GP5B831 / GP5B840 / GP5B841 / GP5B842 / GP5B843 LAN Card GP5B183 / GP5B185 / GP5B186 / GP5B187 Others GP5BUSM103 7

8 NOTES Mountable Card options HS900 MS610 Maximum Maximum number number Cards Product ID Bus of cards Total REMARKS Cards Product ID Bus of cards Total REMARKS mounted mounted SCSI card GP5-123 PCI For external disk array SCSI card GP5-123 PCI64 2 For external disk array (Ultra Wide Diff) (Ultra Wide Diff) 4 8 SCSI card GP5-127 PCI32 6 SCSI card GP5-127 PCI (Ultra2 Wide LVD) (Ultra2 Wide LVD) RAID card GP5-144 PCI64 8 RAID card GP5-144 PCI64 3 (Ultra2 Wide LVD) (Ultra2 Wide LVD) RAID card GP5-146 PCI64 8 RAID card GP5-146 PCI64 2 (Ultra2 Wide LVD) (Ultra2 Wide LVD) LAN card GP5-183 PCI Giga LAN LAN card GP5-183 PCI Giga LAN (1000Base-SX) (1000Base-SX) LAN card GP5-185 PCI32 3 LAN card GP5-185 PCI32 3 (100Base-TX) (100Base-TX) LAN card GP5-187 PCI32 3 IPsec LAN LAN card GP5-186 PCI32 1 Dual Port LAN (100Base-TX) (100Base-TX) LAN card Standard PCI32 1 LAN card GP5-187 PCI32 3 IPsec LAN (100Base-TX) equipment (100Base-TX) Server Monitor Module GP5USM103 PCI Server Monitor Module GP5USM103 PCI MS380 ES280 Maximum Maximum number number Cards Product ID Bus of cards Total REMARKS Cards Product ID Bus of cards Total REMARKS mounted mounted SCSI card GP5-123 PCI External disk array SCSI card GP5-125 PCI Only for external (Ultra Wide Diff) (Ultra Wide) SCSI devices SCSI card GP5-127 PCI32 3 External HDD RAID card GP5U141 PCI32 2 Internal/External (Ultra2 Wide LVD) (Ultra Wide) 2 array configuration RAID card GP5-144 PCI64 3 Internal/External array RAID card GP5-143 PCI32 1 Only for internal array (Ultra2 Wide LVD) configuration Cannot be (Ultra Wide) configuration used with GP5U141/142 LAN card GP5-183 PCI Giga LAN RAID card GP5-146 PCI64 2 Internal/External array (1000Base-SX) (Ultra2 Wide LVD) configuration Cannot be LAN card GP5-185 PCI32 3 used with GP5U141/142 (100Base-TX) LAN card GP5-183 PCI Giga LAN LAN card GP5-187 PCI32 3 IP sec LAN (1000Base-SX) (100Base-TX) LAN card GP5-185 PCI32 3 Server Monitor Module GP5USM103 PCI (100Base-TX) LAN card GP5-187 PCI32 3 (100Base-TX) Server Monitor Module GP5USM103 PCI ES210 ES200 Maximum Maximum number number Cards Product ID Bus of cards Total REMARKS Cards Product ID Bus of cards Total REMARKS mounted mounted SCSI card GP5-127 PCI32 3 Internal HDD/Backup device SCSI card GP5-126 PCI Internal HDD/Backup (Ultra 2Wide LVD) /External device (Ultra 2Wide LVD) 3 device/external device RAID card GP5-143 PCI Internal array configuration SCSI card GP5-127 PCI32 3 Internal Backup device (Ultra2 Wide LVD) 2 (Ultra 2Wide LVD) /External device RAID card GP5-146 PCI64 1 External array configuration RAID card GP5-143 PCI32 1 Internal array (Ultra2 Wide LVD) (Ultra2 Wide LVD) 2 configuration LAN card GP5-183 PCI Giga LAN RAID card GP5-146 PCI External array (1000Base-SX) 3 (Ultra2 Wide LVD) configuration LAN card GP5-185 PCI32 3 LAN card GP5-183 PCI Giga LAN (100Base-TX) (1000Base-SX) LAN card GP5-187 PCI32 3 IPsec LAN LAN card GP5-185 PCI32 3 (100Base-TX) (100Base-TX) Server Monitor Module GP5USM103 PCI LAN card GP5-187 PCI32 3 IPsec LAN (100Base-TX) Server Monitor Module GP5USM103 PCI Server monitoring software (Servervisor V1.0 and Intel LANDesk Server Manager V6.0) is bundled with all teamservers 8

9 NOTES Differences in function and Intel LANDesk Server Manager are indicated below: Differentiation between Servervisor and Intel LANDesk Server Manager Items Servervisor V1.0 Intel LANDesk Server Manager V6.0 Product ES200/ES210/ES280/MS380 All products MS610/HS900 Main function Server status monitoring Server status monitoring Error notification Error message Remote control WindowsNT performance monitoring (e.g. CPU/Memory utilization) Alert function Internet mail transmission Internet mail transmission SNMP Trap transmission SNMP Trap transmission Message box Message box (*On the monitored server) (*On the monitored server) Pager Activation by program Broadcast to connected clients SMM support No Yes Required memory capacity 6~10MB 32~64MB Advantage Servervisor provides the minimum functions LDSM is suitable for systems employing required for server management to reduce remote central monitoring or the amount of resources used, SMM based monitoring to provide making it convenient for a small-scale system a more powerful server management function. without a dedicated manager. - Powerful functions - Simplified operation, light-weight - Easy to use *1 Remote monitoring is provided by System Walker plus LiveHelp. Remote control and WindowsNT performance monitor are provided by System Walker. *2 If the message box is to be displayed for server error detection, the message box must be logged on to the server. Errors that occur while the message box is not logged on can be reported using Internet mail and SNMP Trap. The event log also can be used to check whether such errors have occurred. 9

10 NOTES teamserver HS900 teamserver HS900 CPU: Pentium(R) lllxeon (550MHz) x 2(~8), Cache (L1+L2) : 32KB+2MB/1MB, Internal Hard disk bay:(hot-plug) 2bays, 2 x Ultra2 Wide SCSI Onboard, 2ch RAID Card, CD-ROM, LAN Card (Std.), Redundant Power Supply (Std.)/FAN (Std.), Intel LANDesk Server Manager/Servervisor, ServerWizard GP5T9A32R Rackmount Type 2 x Pentium(R) lll Xeon 550MHz(2MB), Memory:1GB(ECC), HDD:Option Rackmount Type GP5T9A22R Rackmount Type 2 x Pentium(R) lll Xeon 550MHz(1MB), Memory:1GB(ECC), HDD:Option CPU Standard : 2CPUs Max : 8CPUs 1 CPU Field Upgrade Kit (Pentium III Xeon -550MHz (2MB) x1) GP5-FG203T CPU Field Upgrade Kit (Pentium III Xeon-550MHz (1MB) x1) GP5-FG202T Memory Max. memory: 32GB 2 Additional Memory - 256MB (128MB-DIMMx2) Standard memory : 1GB (128MB-DIMMx8) GP5-RM25J 2 Additiond Memory Board Additional Memory - 512MB (256MB-DIMMx2) GP5-RB201 GP5-RM51J Internal Hard Disk Up to two HDDs can be mounted in the main unit Additional Memory - 1GB (512MB-DIMMx2) GP5-RM1J Additional Memory - 2GB (1GB-DIMMx2) GP5-RM2J SCSI on board Max : 2 Hard Disk Drive - 9GB (Ultra2 Wide.10,000rpm) 3 (Hot Plug) GP5-HDH98T 6 RAID Card (GP5-146 : std.) Hard Disk Drive - 18GB (Ultra2 Wide.10,000rpm) (Hot Plug) GP5-HDH85T Connect with Storage System Hard Disk Drive - 36GB (Ultra2 Wide.10,000rpm) (Hot Plug) GP5-HDH61T Max : 8 Hard Disk Drive - 36GB (Ultra160.10,000rpm) 6 (Hot Plug GP5-HDH63/GP5BHDH63 SCSI Card (Ultra2 Wide) SCSI Cable(3m) Max : 1 GP5-127 GP5MU823A Storage System Hard Disk Drive - 9GB (Ultra160.10,000rpm) GP5UR1DC5 (Hot Plug GP5-HDH9A/GP5BHDH9A SCSI Cable(5m) GP5S-833 Hard Disk Drive - 18GB (Ultra160.10,000rpm) (Hot Plug GP5-HDH87/GP5BHDH87 SCSI Cable(10m) GP5S-834 Hard Disk Drive - 18GB (Ultra160.7,200rpm) (Hot Plug GP5-HDH88/GP5BHDH88 Hard Disk Drive - 9GB (Ultra160.7,200rpm) (Hot Plug GP5-HDH9B/GP5BHDH9B Redundant Power Supply Unit GP5UR1PU1/GP5BUR1PU1 10

11 System Configuration Max:8 Hard Disk Drive - 36GB (Ultra160.10,000rpm) 6 (Hot Plug) RAID card cache:32mb SCSI Cable Max:1 Ultra2 Wide SCSI GP5S-832 Storage System Hard Disk Drive - 9GB (Ultra160.10,000rpm) GP5-144 GP5UR1DC5 (Hot Plug) RAID card SCSI Cable Hard Disk Drive - 18GB (Ultra160.10,000rpm) cache:16mb GP5S-835 (Hot Plug) Ultra2 Wide SCSI GP5-146 Hard Disk Drive - 18GB (Ultra160.7,200rpm) SCSI Cable (Hot Plug) GP5S-836 Hard Disk Drive - 9GB (Ultra160.7,200rpm) (Hot Plug) Up to four Tape units can be mounted Redundant Power Supply Unit GP5UR1PU1/GP5BUR1PU1 9 SCSI Cable Backup Cabinet DLT unit (DLT7000) GP5S-832 GP5UR1BC1 GP5-DL351 Occupied two 5" bay slots DAT unit (DDS4) GP5-DT401 Tape unit (MLR3) GP5-ML301 DLT unit (DLT4000) GP5UDL201 Occupied two 5" bay slots DAT unit (DDS3) GP5UDT301 Tape unit (SLR5) GP5USL501 Others Redundant Power Supply Unit GP5UPU151 GP5-183 GP5-185 GP Server Monitor Module GP5USM103 11

12 System Configuration PRIMERGY MS610 CPU:Pentium(R)lll(700MHz)x1(~4)/Cache(L1+L2):(32KB+2MB/1MB)/Onboard SCSI(Ultra160x2, UltraWide/Narrowx1) CD-ROM/LAN (Onboard)/Internal Hard Disk Drive Bay:8~12(Opt.) (Hotplug) Bundled SW:Servervisor/Intel LANDesk(R) Server Manager/ServerWizard GP5T6BH1A GP5T6BH1R GP5T6BG1A GP5T6BG1R 1CPU(Pentium(R)lllXeon700MHz/2MB)/Pedestal Type 1CPU(Pentium(R)lllXeon700MHz/2MB)/Rackmount Type 1CPU(Pentium(R)lllXeon700MHz/1MB)/Pedestal Type 1CPU(Pentium(R)lllXeon700MHz/1MB)/Rackmount Type Pedestal Type <Items> CPU Field upgrade : Go to A Memory addition : Go to B Standard memory conversion : Go to C Connect HDD (Standard Drive Cage) 1.SCSI configuration Go to D 2. Array configuration Go to E 3. Internal backup device Go to F Connect HDD (Drive Cage Conversion Kit) 1.SCSI configuration Go to G 2. Array configuration Go to H 3. Internal backup device Go to I Others (NIC, PSU, etc.) : Go to J Rackmount Type A: CPU 1 CPU Field Upgrade Kit (Pentiumlll Xeon 700MHz (2MB) x1) GP5-FG20H/GP5BFG20H CPU Field Upgrade Kit (Pentiumlll Xeon 700MHz (1MB) x1) GP5-FG20G/GP5BFG20G B: Memory Max.16GB (1GB DIMM x 16) 2 Additional Memory-4GB (1GB SDRAM-DIMMx4) Standard : 256MB (64MB-DIMMx4) GP5-RM4N/GP5BRM4N Additional Memory-2GB(512MB SDRAM-DIMMx4) GP5-RM2N/GP5BRM2N Additional Memory-1GB(256MB SDRAM-DIMMx4) GP5-RM1N/GP5BRM1N Additional Memory-512MB(128MB SDRAM-DIMMx4) GP5-RM51N/GP5BRM51N C: Standard Memory conversion Additional Memory-256MB(64MB SDRAM-DIMMx4) GP5-RM25N/GP5BRM25N 2 Standard Memory Conversion Kit-4GB (1GB SDRAM-DIMMx4) GP5BRU4GA Standard Memory Conversion Kit-2GB (512GB SDRAM-DIMMx4) GP5BRU2GC Standard Memory Conversion Kit-1GB (256GB SDRAM-DIMMx4) GP5BRU1GF Standard Memory Conversion Kit-512MB(64MB SDRAM-DIMMx4) GP5BRU51K 12

13 System Configuration Internal HDD / Internal backup device (Standard Drive Cage) D: Standard Drive Cage 1inch height HDD x 8 SCSI Configuration Hard Disk Drive-9GB(Ultra160, 7,200rpm) 3 1"height/Hotplug GP5-HDH9B/GP5BHDH9B Hard Disk Drive-18GB(Ultra160, 7,200rpm) 1"height/Hotplug GP5-HDH88/GP5BHDH88 Hard Disk Drive-9GB(Ultra160,10,000rpm) 1"height/Hotplug GP5-HDH9A/GP5BHDH9A Hard Disk Drive-18GB(Ultra160,10,000rpm) 1"height/Hotplug GP5-HDH87/GP5BHDH87 Hard Disk Drive-36GB(Ultra160,10,000rpm) 1"height/Hotplug GP5-HDH63/GP5BHDH63 Array Configuration E: 6 Go to SCSI Hard Disk Drive as above RAID Card (32MB Cache/Ultra2 Wide SCSI) GP5-144/GP5B144 F: RAID Card (16MB Cache/Ultra2 Wide SCSI) GP5-146/GP5B146 Internal backup device Connect one backup device (Wide) 4 DLT unit (DLT7000) GP5-DL351/GP5BDL351 Connect secondary backup device (Wide) * Two 5"bays are occupied 6 DAT unit (DDS4) SCSI Card GP5-DT401/GP5BDT401 GP5-127/GP5B127 If mounting two backup devices (Narrow/Wide), SCSI Card (GP5-127) is required for wide connect device. If mounting two backup devices (Wide/Wide), SCSI Card (GP5-127) is required for secondary wide connect device. Tape unit (MLR3) Max.2 backup devices can be mounted GP5-ML301/GP5BML301 Backup device (Narrow) 4 DLT unit (DLT4000) GP5UDL201/GP5BDL201 * Two 5"bays are occupied DAT unit (DDS3) GP5UDT301/GP5BDT301 Tape unit GP5USL501/GP5BSL501 13

14 System Configuration (When Drive Cage Conversion Kit is used) Drive Cage Conversion Kit (for CTO only) (HDD Bay: 8bays to 12bays) GP5BBU1 G: SCSI Configuration 3 Hard Disk Drive-9GB(Ultra160, 7,200rpm) 1"height/Hotplug GP5-HDH9B/GP5BHDH9B. Hard Disk Drive-18GB(Ultra160, 7,200rpm) 1"height/Hotplug GP5-HDH88/GP5BHDH88. Hard Disk Drive-9GB(Ultra160,10,000rpm) 1"height/Hotplug GP5-HDH9A/GP5BHDH9A Hard Disk Drive-18GB(Ultra160,10,000rpm) 1"height/Hotplug GP5-HDH87/GP5BHDH87 H: Array Configuration Hard Disk Drive-36GB(Ultra160,10,000rpm) 1"height/Hotplug GP5-HDH63/GP5BHDH63. 6 Go to SCSI Hard Disk Drive as above RAID Card (32MB Cache/Ultra2 Wide SCSI/3ch) GP5-144/GP5B144 I: RAID Card (16MB Cache/Ultra2 Wide SCSI/2ch) GP5-146/GP5B146 GP5-143/GP5B143 cannot be used with Drive Cage Conversion Kit (GP5BBU1). Internal backup device Backup device (Wide) 4 DLT unit (DLT7000) GP5-DL351/GP5BDL351 SCSI Card * Two 5"bays are occupied GP5-127/GP5B127 DAT unit (DDS4) If mounting two backup devices (Narrow/Wide), SCSI Card (GP5-127) GP5-DT401/GP5BDT401 is required for wide connect device. If mounting two backup devices (Wide/Wide), SCSI Card (GP5-127) is required for secondary wide connect device. Tape unit (MLR3) GP5-ML301/GP5BML301 Max.2 backup devices can be mounted Backup device (Narrow) 4 DLT unit (DLT4000) GP5UDL201/GP5BDL201 * Two 5"bays are occupied DAT unit (DDS3) GP5UDT301/GP5BDT301 Tape unit GP5USL501/GP5BSL501 14

15 System Configuration J: Others GP5-183/GP5B183 GP5-185/GP5B185 GP5-186/GP5B186 GP5-187/GP5B187 One PSU can be added 6 Redundant Power Supply Unit GP5UPU161/GP5BUPU161 6 Server Monitor Module GP5USM103/GP5BUSM103 15

16 System Configuration PRIMERGY MS380 CPU: Pentium(R) lll (850/800/700/600EMHz) x1(~2), Cache (L1+L2) : 32KB+256KB, On board SCSI, CD-ROM, Onboard LAN (Std.), Internal Hard disk bay: 8bays (Hot-plug), Servervisor/ Intel LANDesk Server Manager, Server Wizard PRMIERGY MS380 GP5G804L 1CPU/Pedestal Type 1CPU (Pentium(R)lll 850MHz), Memory:256MB(ECC), HDD:Option GP5G804LR 1CPU/Rackmount Type 1CPU (Pentium(R)lll 850MHz), Memory:256MB(ECC), HDD:Option GP5G803L 1CPU/Pedestal Type 1CPU (Pentium(R)lll 800EMHz), Memory:256MB(ECC), HDD:Option GP5G803LR 1CPU/Rackmount Type 1CPU(Pentium(R)lll 800EMHz), Memory:256MB(ECC), HDD:Option (Pedestal type ) GP5G802L 1CPU/Pedestal Type 1CPU(Pentium(R)lll 700MHz), Memory:256MB(ECC), HDD:Option GP5G802LR 1CPU/Rackmount Type 1CPU(Pentium(R)lll 700MHz), Memory:256MB(ECC), HDD:Option (Rackmount type) GP5G801L 1CPU/Pedestal Type 1CPU(Pentium(R)lll 600EMHz), Memory:256MB(ECC), HDD:Option GP5G801LR 1CPU/Rackmount Type 1CPU(Pentium(R)lll 600EMHz), Memory:256MB(ECC), HDD:Option CPU Max : 2CPUs CPU Field Upgrade Kit-63 (Pentium III-850MHz (256KB) x1) 1 GP5-FG20C/GP5BFG20C CPU Field Upgrade Kit-62 (Pentium III-800MHz (256KB) x1) GP5-FG20B/GP5BFG20B CPU Field Upgrade Kit-56 (Pentium III-700MHz (256KB) x1) GP5-FG205/GP5BFG205 CPU Field Upgrade Kit-57 (Pentium III-600EMHz (256KB) x1) GP5-FG12Y/GP5BFG12Y Memory Max.2GB 2 Additional Memory - 64MB (64MB SDRAM-DIMM x1) Standard memory : 256MB (256MB SDRAM-DIMM x1) GP5-RM64F/GP5BRM64F Additional Memory -128MB (128MB SDRAM-DIMM x1) GP5-RM12F/GP5BRM12F Additional Memory - 256MB (256MB SDRAM-DIMM x1) GP5-RM25F/GP5BRM25F Additional Memory MB( 512MB SDRAM-DIMMx1) GP5-RM51F/GP5BRM51F Standard Memory Conversion Option 2 Standard Memory Conversion Kit-512MB ( 512MB SDRAM-DIMMx1) GP5BRU51F Internal Hard Disk (1)Disk Addition / Duplexing Hard Disk Drive - 9GB (Ultra2 Wide.10,000rpm) : max 6 3 (Hot Plug) Up to 8 disks GP5-HDH9A/GP5BHDH9A Hard Disk Drive -18GB (Ultra2 Wide.10,000rpm) : max 6 (Hot Plug) GP5-HDH87/GP5BHDH87 Hard Disk Drive - 9GB (Ultra2 Wide.7,200rpm) (Hot Plug) GP5-HDH96/GP5BHDH96 Hard Disk Drive -18GB (Ultra2 Wide.7,200rpm) (Hot Plug) GP5-HDH83/GP5BHDH83 16

17 System Configuration (2)Internal Disk Array Hard Disk Drive - 9GB (Ultra2 Wide.10,000rpm) : max 6 6 RAID Card (Cache : 32MB, Ultra2 Wide SCSI, BBU) (Hot Plug) GP5-144/GP5B144 GP5-HDH9A/GP5BHDH9A RAID Card (Cache :16MB, Ultra2 Wide SCSI, BBU) Hard Disk Drive -18GB (Ultra2 Wide.10,000rpm) : max 6 GP5-146/GP5B146 (Hot Plug) GP5-HDH87/GP5BHDH87 Hard Disk Drive - 9GB (Ultra2 Wide.7,200rpm) (Hot Plug) GP5-HDH96/GP5BHDH96 Hard Disk Drive -18GB (Ultra2 Wide.7,200rpm) (Hot Plug) GP5-HDH83/GP5BHDH83 Internal Devices 6 DLT unit (DLT7000)*(Occupied two 5" bay slots) GP5-DL351/GP5BDL351 SCSI Card GP5-127/GP5B127 Tape unit (MLR3) GP5-ML301/GP5BML301 *NOTE : 2 PSUs are required as standard if GP5-DL351 is installed Maximum 3PSUs can be installed in MS380. DAT unit (DDS4) GP5-DT401/GP5BDT401 4 DLT unit (DLT4000)(Occupied two 5" bay slots) GP5UDL201/GP5BDL201 DAT unit (DDS3) GP5UDT301/GP5BDT301 Tape unit (SLR5) GP5USL501/GP5BSL501 Others GP5-183/GP5B183 GP5-185/GP5B185 GP5-187/GP5B187 8 Redundant Power Supply Unit GP5UPU131/GP5BUPU131 6 Server Monitor Module GP5USM103/GP5BUSM103 *NOTE : 2 PSUs are required as standard if GP5-DL351 is installed Maximum 3PSUs can be installed in MS

18 System Configuration PRIMERGY ES280 PRIMERGY ES280 CPU: Pentium (R)lll (800/700/600EMHz)x1(~2),Cache (L1+L2) : 32KB+256KB, On board SCSI, CD-ROM, Onboard LAN (Std.), Internal Hard disk bay: 4bays (3xHot-plug), Bundled SW : Servervisor/ Intel LANDesk Server Manager, ServerWizard GP5C803 1CPU/Pedestal Type 1CPU (Pentium(R)lll 800MHz), Memory:128MB(ECC), HDD:Option GP5C803R 1CPU/Rackmount Type 1CPU (Pentium(R)lll 800MHz), Memory:128MB(ECC), HDD:Option GP5C802 1CPU/Pedestal Type 1CPU (Pentium(R)lll 700MHz), Memory:128MB(ECC), HDD:Option (Pedestal type ) GP5C802R 1CPU/Rackmount Type 1CPU (Pentium(R)lll 700MHz), Memory:128MB(ECC), HDD:Option GP5C801 1CPU/Pedestal Type 1CPU (Pentium(R)lll 600EMHz), Memory:128MB(ECC), HDD:Option (Rackmount type) GP5C801R 1CPU/Rackmount Type 1CPU (Pentium(R)lll 600EMHz), Memory:128MB(ECC), HDD:Option CPU Max : 2CPUs 1 CPU Field Upgrade Kit-62 (Pentium III-800MHz (256KB) x1) GP5-FG20B/GP5BFG20B CPU Field Upgrade Kit-56 (Pentium III-700MHz (256KB) x1) GP5-FG205/GP5BFG205 CPU Field Upgrade Kit-57 (Pentium III-600EMHz (256KB) x1) GP5-FG12Y/GP5BFG12Y Memory Max.1GB 2 Additional Memory - 64MB (64MB SDRAM-DIMMx1) Standard : 128MB (128MB SDRAM-DIMMx1) GP5-RM64F/GP5BRM64F Additional Memory - 128MB (128MB SDRAM-DIMMx1) GP5-RM12F/GP5BRM12F Additional Memory - 256MB (256MB SDRAM-DIMMx1) GP5-RM25F/GP5BRM25F Standard Memory Conversion Option Standard Memory Conversion Kit-256MB 2 (256MB SDRAM-DIMMx1) GP5BRU25E Internal Hard Disk Total 4 disks(3hot Plug and1non-hot Plug)Can be installed. (1)Disk Addition to Hot Plug bays (Max. 3 disks) 6 Hard Disk Drive - 9GB (Ultra Wide.7,200rpm)(Hot Plug) GP5-HDH96/GP5BHDH96 Hard Disk Drive -18GB (Ultra Wide.7,200rpm)(Hot Plug) GP5-HDH83/GP5BHDH83 (2)Internal Disk Array (Maximum 3Hot Plug diskscan be installed) 6 Hard Disk Drive - 9GB (Ultra Wide.7,200rpm)(Hot Plug) RAIDCard (Cache :16MB) GP5-HDH96/GP5BHDH96 GP5U141/GP5BU141 GP5U831/GP5B831 SCSICable (Intl.) Hard Disk Drive -18GB (Ultra Wide.7,200rpm)(Hot Plug) RAIDCard (Cache : 8MB Internal Hard disk only) GP5-HDH83/GP5BHDH83 GP5-143/GP5B143 18

19 System Configuration (3)Disk Addition to a non-hot Plug bay only one diskcan be installed 3 Hard Disk Drive - 9GB (7,200rpm) (non-hot Plug) GP5-HD9G3/GP5BHD9G3 Hard Disk Drive -18GB (7,200rpm) (non-hot Plug) GP5-HD8G1/GP5BHD8G1 Internal Devices 6 Tape unit (MLR3) GP5-ML301/GP5BML301 SCSI Card GP5-125/GP5B125 DAT unit (DDS4) GP5-DT401/GP5BDT401 4 DAT unit (DDS3) GP5UDT301/GP5BDT301 s Others Tape unit (SLR5) GP5USL501/GP5BSL501 GP5-183/GP5B183 GP5-185/GP5B185 GP5-187/GP5B187 6 Server Monitor Module GP5USM103/GP5BUSM103 19

20 System Configuration PRIMERGY ES210 CPU:Pentium(R)lll(850/700/600EMHz)x1(~2),Cache(L1+L2):32KB+256KBx2/Onboard SCSI(1xUltra Wide, 1xFast Narrow) 3PCI(32bit33MHz)/CD-ROM/Onboard LAN(Std.)/Internal Hard Disk Drive Bay:4 (Non Hotplug) Bundled S/W: Servervisor/Intel LANDesk(R) Server Manager/ServerWizard GP5T2BC1A: GP5T2B51A: GP5T2BY1A: 1CPU(Pentium(R)lll850MHz)/Pedestal Type 1CPU(Pentium(R)lll700MHz)/Pedestal Type 1CPU(Pentium(R)lll600EMHz)/Pedestal Type A: <Items> CPU Field Upgrade : Memory addition : Standard memory conversion : SCSI configuration Internal Hard Disk Drive (Ultra Wide) : Internal Hard Disk Drive (Ultra2 Wide) : Internal backup device : IDE/Array configuration Internal Hard Disk Drive (IDE) : Internal Hard Disk Drive (Array) : Internal backup device : Others (NIC, PSU, etc.) : Go to A Go to B Go to C Go to D Go to E Go to F Go to G Go to H Go to I Go to J CPU 1 CPU Field Upgrade Kit-63(Pentiumlll 850MHz(256KB)x1) GP5-FG20C/GP5BFG20C CPU Field Upgrade Kit-56 (Pentiumlll 700MHz(256KB)x1) GP5-FG205/GP5BFG205 CPU Field Upgrade Kit-57(Pentiumlll 600EMHz(256KB)x1) GP5-FG12Y/GP5BFG12Y B: Memory Max:1GB(256MB SDRAM-DIMM x 4) 2 Additional Memory-64MB (64MB SDRAM-DIMMx1) Standard:128MB (128MB SDRAM-DIMMx1) GP5-RM64H/GP5BRM64H Additional Memory-128MB (128MB SDRAM-DIMMx1) GP5-RM12H/GP5BRM12H Additional Memory-256MB (256MB SDRAM-DIMMx1) C: GP5-RM25H/GP5BRM25H Standard Memory conversion option 2 Standard Memory Conversion Kit-256MB (256MB SDRAM-DIMMx1) GP5BRU25D Internal HDD / Internal backup device (SCSI Configuration) D: Ultra Wide Max: 4 HDDs Hard Disk Drive-9GB(Ultra2 Wide SCSI,7,200rpm) Onboard SCSI GP5-HD9G3/GP5BHD9G3 (For HDD bay:up to 3HDDs can be mounted) SCSI Cable GP5-HD9G3C /GP5BHD9G3C (For 5"bay:Only one can be mounted) E: GP5-843/GP5B843 Ultra2 Wide 6 Hard Disk Drive-18GB(Ultra2 Wide SCSI,7,200rpm) GP5-HD8G1/GP5BHD8G1 (For HDD bay:up to 3HDDs can be mounted) SCSI Card GP5-HD8G1C/GP5BHD8G1C(For 5"bay:Only one can be mounted) GP5-127/GP5B127 20

21 System Configuration F: DAT unit(dds3) GP5UDT301/GP5BDT301 Max.2 backup devices can be mounted 6 DAT unit(dds4) GP5-DT401/GP5BDT401 SCSI Card GP5-127/GP5B127 SCSI Cable is supplied with wide backup devices. G: (IDE configuration) Max:2 IDE Disk can be mounted 3 Hard Disk Drive-20GB(Ultra33/DMA,5,400rpm) GP5-HD2E1/GP5BHD2E1 H: (Array configuration) 6 Go to SCSI Hard Disk Drive as above RAID Card (8MB Cache, Ultra2 Wide SCSI, SCSI Cable Only for internal HDD connection) GP5-843/GP5B843 I: GP5-143/GP5B143 6 DAT unit (DDS3) GP5UDT301/GP5BDT301 SCSI Card (GP5-127/GP5B127) is required for mounting Wide connect backup device. Max.2 backup devices can be mounted 6 DAT unit (DDS4) GP5-DT401/GP5BDT401 SCSI Card SCSI Cable is a standard equipment of backup device GP5-127/GP5B127 J: Others GP5-183/GP5B183 GP5-185/GP5B185 GP5-187/GP5B187 6 Server Monitor Module GP5USM103/GP5BUSM103 21

22 System Configuration PRIMERGY ES200 CPU:Pentium(R)lll(600EMHz),Cache(L1+L2):32KB+256KB/Celeron(500MHz)x1,Cache(L1+L2):32KB+128KB 4PCI(32bit33MHz)/CD-ROM/Onboard LAN(Std.)/Internal Hard Disk Drive Bay:4 (Non Hotplug) Bundled S/W: Servervisor/Intel LANDesk(R) Server Manager/ServerWizard GP5T2AY1A 1CPU(Pentium(R)lll600EMHz)/Pedestal Type GP5T2AF1A 1CPU(Celeron(R)500MHz)/Pedestal Type <Items> Memory addition : Standard memory conversion : SCSI configuration Internal Hard Disk Drive (Ultra Wide) : Internal backup device : IDE/Array configuration Internal Hard Disk Drive (IDE) : Internal Hard Disk Drive (Array) : Internal backup device : Others (NIC, PSU, etc.) : GoTo A GoTo B GoTo C GoTo D GoTo E GoTo F GoTo G GoTo H A: Memory Max:768MB (256MB SDRAM-DIMM x3) 2 Additional Memory-64MB (64MB SDRAM-DIMMx1) Standard:128MB (128MB SDRAM-DIMMx1) GP5-RM64H/GP5BRM64H Additional Memory-128MB (128MB SDRAM-DIMMx1) GP5-RM12H/GP5BRM12H Additional Memory-256MB (256MB SDRAM-DIMMx1) B: GP5-RM25H/GP5BRM25H Standard Memory conversion option 2 Standard Memory Conversion Kit-256MB (256MB SDRAM-DIMMx1) GP5BRU25D Internal HDD / Internal backup device C: (SCSI Configuration) Max:Four HDDs 6 Hard Disk Drive-9GB(Ultra2 Wide SCSI,7,200rpm) GP5-HD9G3/GP5BHD9G3 (For HDD bay:up to 3HDDs can be mounted) SCSI Card SCSI Cable GP5-HD9G3C/GP5BHD9G3C (For 5"bay:Only one can be mounted) GP5-126/GP5B126 GP5-843/GP5B843 Hard Disk Drive-18GB(Ultra2 Wide SCSI,7,200rpm) GP5-HD8G1/GP5BHD8G1 (For HDD bay:up to 3HDDs can be mounted) GP5-HD8G1C/GP5BHD8G1C(For 5"bay:Only one can be mounted) D: SCSI Cable GP5-841/GP5B841 Max.2 backup devices can be mounted DAT unit (DDS3) GP5UDT301/GP5BDT301 Only one DDS3 can be mounted in "bay2" Tape unit GP5USL501/GP5BSL501 6 DAT unit (DDS4) GP5-DT401/GP5BDT401 SCSI Card SCSI Cable GP5-127/GP5B127 GP5-840/GP5B840 Tape unit (MLR3) GP5-ML301/GP5BML301 E: (IDE configuration) Max:2 IDE Disk can be mounted 3 Hard Disk Drive-20GB(Ultra33/DMA,5,400rpm) GP5-HD2E1/GP5BHD2E1 22

23 System Configuration F: (Array configuration) 6 Go to SCSI Hard Disk Drive as above RAID Card (8MB Cache, Ultra2 Wide SCSI, SCSI Cable Only for internal HDD connection) GP5-843/GP5B843 GP5-143/GP5B143 SCSI Card (GP5-127/GP5B127) is required for mounting backup devices as shown below. G: 6 DAT unit (DDS3) SCSI Card GP5UDT301/GP5BDT301 GP5-127/GP5B127 SCSI Cable GP5-840/GP5B840 Max.2 backup devices can be mounted Tape unit GP5USL501/GP5BSL501 DAT unit (DDS4) GP5-DT401/GP5BDT401 SCSI Cable is supplied as standard equipment with wide backup devices. Tape unit (MLR3) GP5-ML301/GP5BML301 H: Others GP5-183/GP5B183 GP5-185/GP5B185 GP5-187/GP5B187 6 Server Monitor Module GP5USM103/GP5BUSM103 External Disk Array PRIMERGY HS900 / MS610 / MS SCSI Card SCSI Cable GP5-123 (Procured locally) 23

24 System Configuration External Devices (Pedestal only) HS900 MS610 MS380 ES280 ES210 ES200 Hard disk cabinet Disk addition 6 SCSI card SCSI cable GP5-125/GP5B125 GP5MU823A ES280 only Disk array 6 RAID card(cache:16mb) SCSI cable GP5U141/GP5BU141 GP5MU829A ES280 only Disk addition SCSI card SCSI cable Hard disk cabinet GP5-127/GP5B127 GP5MU823A GP5MS623A MS380 only Disk array 6 6 RAID card(cache:32mb) SCSI cable GP5-144/GP5B144 GP5S-832 MS380 only Disk array RAID card(cache:16mb) SCSI cable GP5-146/GP5B146 GP5S-832 MS380 only Configuration of the inside Hard disk cabinet Hard Disk Drive-9GB (7,200rpm) GP5-HDH9B/GP5BHDH9B Hard Disk Drive-9GB (10,000rpm) GP5-HDH9A/GP5BHDH9A Hard Disk Drive-18GB (10,000rpm) GP5-HDH87/GP5BHDH87 Hard Disk Drive-36GB (10,000rpm) GP5-HDH63/GP5BHDH63 Hard Disk Drive-18GB (7,200rpm) GP5-HDH88/GP5BHDH88 Power Supply Unit GP5URIPU1/GP5BUR1PU1 24

25 System Configuration Rackmount Rack Option Rack Mount Pattern 40U Rack 40U Rack & Rack Coupling Kit GP5-RMP GP5-R1RC4 GP5-R1RC5 CPU or DISK node 24U Rack GP5-R2RC1 24U Rack & Rack Coupling Kit GP5-R2RC2 Component Shelf GP5-R1TB4 Keyboard/Monitor Shelf Kit GP5-R1TB5 (For GP5-R2RC1/GP5-R1RC4) (Up to 8 servers connection) Keyboard/Monitor Cable Keyboard/Monitor Enhanced Switch Flat Display GP5-418(5.0m) GP5-SB102 GP5UR1DP1 (Up to 4 servers connection) Keyboard/Monitor Cable Keyboard/Monitor Enhanced Switch Enhanced Keyboard GP5-411 (3.0m) GP5-SB101 GP5-R1KB2 Up to eight servers can be connected to one GP5-SB102, and up to 64 servers can be connected with nine GP5-SB102 in cascade connection (Keyboard Monitor Cable: GP5-414 is required) Power Distribution Unit GP5UPDU1 GP5-SB102 GP5-SB102 GP5-414 HS900 MS610 MS380 ES280 6 Storage System SCSI card SCSI Cable GP5UR1DC5 ES280 only GP5-125/GP5B125 GP5MU823A 6 ES280 only RAID card* GP5U141/GP5BU141 SCSI Cable GP5MU829A 6 6 MS380 only SCSI card GP5-127/GP5B127 SCSI Cable GP5MU823A/GP5S-833/ MS380 only RAID card GP5-144/GP5B144 SCSI Cable GP5S-832/835/ MS380 only RAID card GP5-146/GP5B146 SCSI Cable GP5S-832/835/836 25

26 System Configuration Inside of Storage System Hard Disk Drive-9GB (7,200rpm) GP5-HDH9B/GP5BHDH9B Hard Disk Drive-9GB (10,000rpm) GP5-HDH9A/GP5BHDH9A Hard Disk Drive-18GB (10,000rpm) GP5-HDH87/GP5BHDH87 Hard Disk Drive-36GB (10,000rpm) GP5-HDH63/GP5BHDH63 Hard Disk Drive-18GB (7,200rpm) Power Supply Unit GP5-HDH88/GP5BHDH88 GP5URIPU1/GP5BUR1PU1 NOTE A maximum of eight Hard Disk Drives can be installed in a Storage System. In a RAID configuration, a physical pack must be comprised of the same type of Hard disks. 26

27 Hardware Product Product ID Remarks teamserver HS900 GP5T9A32R Pentium lll Xeon 550MHz with 2MB Cache (x2, up to 8CPUs), 1GB SDRAM-DIMM(128MBx8) with ECC ( 32GB maximum ) (Rackmount) # of HDD Bay: 2(Hotplug) [Up to twelve Storage System(GP5UR1DC4) can be mounted as external storage]/32xspeed CD-ROM /LAN Card(Std.) Onboard SCSI:Ultra2 Widex2/ 10PCI(4x64bit66MHz, 6x64bit/33MHz) Redundant&Hotplug PSU(Std.), Redundant&Hotplug&Proactive Fan(Std.) Rackmount7U, teamserver HS900 GP5T9A22R Pentium lll Xeon 550MHz with 1MB Cache (x2, up to 8CPUs), 1GB SDRAM-DIMM(128MBx8) with ECC ( 32GB maximum ) (Rackmount) # of HDD Bay: 2(Hotplug) [Up to twelve Storage System(GP5UR1DC4) can be mounted as external storage]/32xspeed CD-ROM /LAN Card(Std.) Onboard SCSI:Ultra2 Widex2/ 10PCI(4x64bit66MHz, 6x64bit/33MHz) Redundant&Hotplug PSU(Std.), Redundant&Hotplug&Proactive Fan(Std.) Rackmount7U, PRIMERGY MS610 GP5T6BH1A Pentium lll Xeon 700MHz with 2MB Cache (x1, up to 4CPUs), 256MB SDRAM-DIMM(64MBx4) with ECC, ( 16GB maximum ) (Pedestal) # of HDD Bay: 8(Hotplug) [12(Hotplug): When drive cage conversion (GP5BBU1)]/40Xspeed CD-ROM /LAN Card(Onboard)/ Onboard SCSI:Ultra160x2, Wide or Narrowx1/8PCI(2x64bit66MHz, 4x64bit/33MHz, 2x32bit/33MHz) Redundant&Hotplug PSU(Opt.)/Redundant&Hotplug&Proactive Fan(Std.) PRIMERGY MS610 GP5T6BH1R Pentium lll Xeon 700MHz with 2MB Cache (x1, up to 4CPUs), 256MB SDRAM-DIMM(64MBx4) with ECC, ( 16GB maximum ) (Rackmount) # of HDD Bay: 8(Hotplug) [12(Hotplug): When drive cage conversion (GP5BBU1)]/40Xspeed CD-ROM /LAN Card(Onboard)/ Onboard SCSI:Ultra160x2, Wide or Narrowx1/8PCI(2x64bit66MHz, 4x64bit/33MHz, 2x32bit/33MHz) Redundant&Hotplug PSU(Opt.)/Redundant&Hotplug&Proactive Fan(Std.) PRIMERGY MS610 GP5T6BG1A Pentium lll Xeon 700MHz with 1MB Cache (x1, up to 4CPUs), 256MB SDRAM-DIMM(64MBx4) with ECC, ( 16GB maximum ) (Pedestal) # of HDD Bay: 8(Hotplug) [12(Hotplug): When drive cage conversion (GP5BBU1)]/40Xspeed CD-ROM /LAN Card(Onboard)/ Onboard SCSI:Ultra160x2, Wide or Narrowx1/8PCI(2x64bit66MHz, 4x64bit/33MHz, 2x32bit/33MHz) Redundant&Hotplug PSU(Opt.)/Redundant&Hotplug&Proactive Fan(Std.) PRIMERGY MS610 GP5T6BG1R Pentium lll Xeon 700MHz with 1MB Cache (x1, up to 4CPUs), 256MB SDRAM-DIMM(64MBx4) with ECC, ( 16GB maximum ) (Rackmount) # of HDD Bay: 8(Hotplug) [12(Hotplug): When drive cage conversion (GP5BBU1)]/40Xspeed CD-ROM /LAN Card(Onboard)/ Onboard SCSI:Ultra160x2, Wide or Narrowx1/8PCI(2x64bit66MHz, 4x64bit/33MHz, 2x32bit/33MHz) Redundant&Hotplug PSU(Opt.)/Redundant&Hotplug&Proactive Fan(Std.) PRIMERGY MS380 GP5G804L Pentium lll850mhz with 256KB Cache (x1, up to 2CPUs), 256MB SDRAM (256MB x1) with ECC (2GB maximum) (Pedestal) # of HDD Bay: 8(Hotplug)/32Xspeed CD-ROM /Onboard LAN/Onboard SCSI:Ultra2Widex2, Narrowx1 32bit/33MHzPCIx4, PCI/ISAx1, ISAx1/Redundant&Hotplug PSU(Opt.), Redundant&Hotplug Fan(Std.) PRIMERGY MS380 GP5G804LR Pentium lll850mhz with 256KB Cache (x1, up to 2CPUs), 256MB SDRAM (256MB x1) with ECC (2GB maximum) (Rackmount) # of HDD Bay: 8(Hotplug)/32Xspeed CD-ROM /Onboard LAN/Onboard SCSI:Ultra2Widex2, Narrowx1 32bit/33MHzPCIx4, PCI/ISAx1, ISAx1/Redundant&Hotplug PSU(Opt.), Redundant&Hotplug Fan(Std.) PRIMERGY MS380 GP5G803L Pentium lll800mhz with 256KB Cache (x1, up to 2CPUs), 256MB SDRAM (256MB x1) with ECC (2GB maximum) (Pedestal) # of HDD Bay: 8(Hotplug)/32Xspeed CD-ROM /Onboard LAN/Onboard SCSI:Ultra2Widex2, Narrowx1 32bit/33MHzPCIx4, PCI/ISAx1, ISAx1/Redundant&Hotplug PSU(Opt.), Redundant&Hotplug Fan(Std.) PRIMERGY MS380 GP5G803LR Pentium lll800mhz with 256KB Cache (x1, up to 2CPUs), 256MB SDRAM (256MB x1) with ECC (2GB maximum) (Rackmount) # of HDD Bay: 8(Hotplug)/32Xspeed CD-ROM /Onboard LAN/Onboard SCSI:Ultra2Widex2, Narrowx1 32bit/33MHzPCIx4, PCI/ISAx1, ISAx1/Redundant&Hotplug PSU(Opt.), Redundant&Hotplug Fan(Std.) PRIMERGY MS380 GP5G802L Pentium lll700mhz with 256KB Cache (x1, up to 2CPUs), 256MB SDRAM (256MB x1) with ECC (2GB maximum) (Pedestal) # of HDD Bay: 8(Hotplug)/32Xspeed CD-ROM /Onboard LAN/Onboard SCSI:Ultra2Widex2, Narrowx1 32bit/33MHzPCIx4, PCI/ISAx1, ISAx1/Redundant&Hotplug PSU(Opt.), Redundant&Hotplug Fan(Std.) PRIMERGY MS380 GP5G802LR Pentium lll700mhz with 256KB Cache (x1, up to 2CPUs), 256MB SDRAM (256MB x1) with ECC (2GB maximum) (Rackmount) # of HDD Bay: 8(Hotplug)/32Xspeed CD-ROM /Onboard LAN/Onboard SCSI:Ultra2Widex2, Narrowx1 32bit/33MHzPCIx4, PCI/ISAx1, ISAx1/Redundant&Hotplug PSU(Opt.), Redundant&Hotplug Fan(Std.) 27

28 Hardware Product Product ID Remarks PRIMERGY MS380 GP5G801L (Pedestal) Pentium lll600emhz with 256KB Cache (x1, up to 2CPUs), 256MB SDRAM (256MB x1) with ECC (2GB maximum) # of HDD Bay: 8(Hotplug)/32Xspeed CD-ROM /Onboard LAN/Onboard SCSI:Ultra2Widex2, Narrowx1 32bit/33MHzPCIx4, PCI/ISAx1, ISAx1/Redundant&Hotplug PSU(Opt.), Redundant&Hotplug Fan(Std.) PRIMERGY MS380 GP5G801LR Pentium lll600emhz with 256KB Cache (x1, up to 2CPUs), 256MB SDRAM (256MB x1) with ECC (2GB maximum) (Rackmount) # of HDD Bay: 8(Hotplug)/32Xspeed CD-ROM /Onboard LAN/Onboard SCSI:Ultra2Widex2, Narrowx1 32bit/33MHzPCIx4, PCI/ISAx1, ISAx1/Redundant&Hotplug PSU(Opt.), Redundant&Hotplug Fan(Std.) PRIMERGY ES280 GP5C803 Pentium lll800mhz with 256KB Cache (x1, up to 2CPUs), 128MB SDRAM (128MB x1) with ECC (1GB maximum) (Pedestal) # of HDD Bay: 4(3Hotplug)/32Xspeed CD-ROM /Onboard LAN/Onboard SCSI:UltraWidex1, Narrowx1 32bit/33MHzPCIx3, ISAx2 PRIMERGY ES280 GP5C803R Pentium lll800mhz with 256KB Cache (x1, up to 2CPUs), 128MB SDRAM (128MB x1) with ECC (1GB maximum) (Rackmount) # of HDD Bay: 4(3Hotplug)/32Xspeed CD-ROM /Onboard LAN/Onboard SCSI:UltraWidex1, Narrowx1 32bit/33MHzPCIx3, ISAx2 PRIMERGY ES280 GP5C802 Pentium lll700mhz with 256KB Cache (x1, up to 2CPUs), 128MB SDRAM (128MB x1) with ECC (1GB maximum) (Pedestal) # of HDD Bay: 4(3Hotplug)/32Xspeed CD-ROM /Onboard LAN/Onboard SCSI:UltraWidex1, Narrowx1 32bit/33MHzPCIx3, ISAx2 PRIMERGY ES280 GP5C802R Pentium lll700mhz with 256KB Cache (x1, up to 2CPUs), 128MB SDRAM (128MB x1) with ECC (1GB maximum) (Rackmount) # of HDD Bay: 4(3Hotplug)/32Xspeed CD-ROM /Onboard LAN/Onboard SCSI:UltraWidex1, Narrowx1 32bit/33MHzPCIx3, ISAx2 PRIMERGY ES280 GP5C801 Pentium lll600emhz with 256KB Cache (x1, up to 2CPUs), 128MB SDRAM (128MB x1) with ECC (1GB maximum) (Pedestal) # of HDD Bay: 4(3Hotplug)/32Xspeed CD-ROM /Onboard LAN/Onboard SCSI:UltraWidex1, Narrowx1 32bit/33MHzPCIx3, ISAx2 PRIMERGY ES280 GP5C801R Pentium lll600emhz with 256KB Cache (x1, up to 2CPUs), 128MB SDRAM (128MB x1) with ECC (1GB maximum) (Rackmount) # of HDD Bay: 4(3Hotplug)/32Xspeed CD-ROM /Onboard LAN/Onboard SCSI:UltraWidex1, Narrowx1 32bit/33MHzPCIx3, ISAx2 PRIMERGY ES210 GP5T2BC1A Pentium lll850mhz with 256KB Cache (x1, up to 2CPUs), 128MB SDRAM (128MBx1) with ECC (1GB maximum ) (Pedestal) # of HDD Bay: 4(Non hotplug)[2xscsi Bay + 2xSCSI bay(scsi/eide HDD both can be mounted) (End Jun 2000) 40Xspeed CD-ROM /Onboard LAN/Onboard SCSI:UltraWidex1, Narrowx1 PRIMERGY ES210 GP5T2B51A Pentium lll700mhz with 256KB Cache (x1, up to 2CPUs), 128MB SDRAM (128MBx1) with ECC (1GB maximum ) (Pedestal) # of HDD Bay: 4(Non hotplug)[2xscsi Bay + 2xSCSI bay(scsi/eide HDD both can be mounted) (End Jun 2000) 40Xspeed CD-ROM /Onboard LAN/Onboard SCSI:UltraWidex1, Narrowx1 PRIMERGY ES210 GP5T2BY1A Pentium lll600emhz with 256KB Cache (x1, up to 2CPUs), 128MB SDRAM (128MBx1) with ECC (1GB maximum ) (Pedestal) # of HDD Bay: 4(Non hotplug)[2xscsi Bay + 2xSCSI bay(scsi/eide HDD both can be mounted) (End Jun 2000) 40Xspeed CD-ROM /Onboard LAN/Onboard SCSI:UltraWidex1, Narrowx1 PRIMERGY ES200 GP5T2AY1A2 Pentium lll600emhz with 256KB Cache (x1), 128MB SDRAM (128MBx1) with ECC (768MB maximum ) (Pedestal) # of HDD Bay: 4(Non hotplug)[2xscsi Bay(Use one 5"Bay) + 2xSCSI bay(scsi/eide HDD both can be mounted) (End Jun 2000) 40Xspeed CD-ROM /Onboard LAN PRIMERGY ES200 GP5T2AF1A2 Celeron500MHz with 128KB Cache (x1), 128MB SDRAM (128MBx1) with ECC (768MB maximum ) (Pedestal) # of HDD Bay: 4(Non hotplug)[2xscsi Bay(Use one 5"Bay) + 2xSCSI bay(scsi/eide HDD both can be mounted) (End Jun 2000) 40Xspeed CD-ROM /Onboard LAN 28