System Configuration and Order-information Guide BX620 S3. March 2007

Transcription

1 System Configuration and Order-information Guide BX620 S3 March 2007

2 View Expansion Board slot DIMM Slot CPU Hard Disk Bay PRIMERGY BX600 S2 Blade Server System Unit Front View Back View Switch Blade (optional) / GbE Pass-Thru Blade (optional) FC Switch Blade (optional) / FC Pass-Thru Blade (optional) / Switch Blade (optional) / GbE Pass-Thru Blade (optional) Power Supply (optional) Management Blade Keyboard / Mouse / Display Management LAN Management Console Port Power Supply

3 Instruction This document contains basic product and configuration information that will enable you to configure your system. Only these tools will ensure a fast and proper configuration of your PRIMERGY server or your complete PRIMERGY Rack system. You can configure your individual PRIMERGY server in order to meet your specific requirements. Please follow the lines. If there is a junction, you can choose which way or component you would like to take. Go through the configurator by following the lines from the top to the bottom. The color of the junction means as follows. Key to Or And

4 Data Sheet Type Dual-Processor Blade Server Base Unit Xeon 5110 (1.60GHz) PGUX6233A CPU Xeon LV 5148 (2.33GHz) Frequencies Second-Level-Cache PGUX6239A Quad Core Intel Xeon X5355 (2.66GHz) *5 / E5310 (1.60GHz) *6 / Dual Core Intel Xeon 5160 (3GHz) *7 / 5130 (2GHz) *8 / 5110 (1.60GHz) / LV 5148 (2.33GHz) 2x4MB ( Quad Core Intel Xeon X5355 (2.66GHz) / E5310 (1.60GHz) ) / 4MB ( Dual Core Intel Xeon 5160 (3GHz) / 5130(2GHz) / 5110 (1.60GHz) / LV 5148 (2.33GHz) ) Multi-Processor 1 (max. 2) Front-Side-Bus 1333MHz ( Quad Core Intel Xeon X5355 (2.66GHz) / Dual Core Intel Xeon 5160 (3GHz) / 5130 (2GHz) / LV 5148 (2.33GHz) ) / 1066MHz ( Quad Core Intel Xeon E5310 (1.60GHz) / Dual Core Intel Xeon 5110 (1.60GHz) ) / Chipset Intel 5000P Memory Standard 1GB (512MB ECC DDR2 SDRAM Fully Buffered DIMM x 2, PC2 5300F) (SDDC(Single Device Data Correction) supported) Maximum *1 32GB (4GB ECC DDR2 SDRAM Fully Buffered DIMM x 8, PC2 5300F) Graphics Controller ATI ES 1000, VRAM : 16MB (PCI) Resolution *2 640x480/800x600/1024x768/1280x1024 dot Internal Bays Number of bays inch Available HDD *3 36.7GB (PG-HDD61A) 10krpm, SAS HDD Maximum *3 PCI Slots PCI Express (x4) [x4] PCI-X (64bit/133MHz) [3.3V] RAID Controller SAS Controller 73.4GB (PG-HDD71A) 10krpm, SAS 146.8GB optional (1 : LowProfile PCI Express Card only when Expansion Card Slot Module (PGBCS104) is applied.) optional (1 : LowProfile PCI Card only when Expansion Card Slot Module (PGBCS103) is applied.) Onboard Onboard, SAS x 2ports (with RAID1 function) LAN Interfaces 2ports (1Gbps) ( 4ports (1Gbps) when 1Gbit/s Ethernet I/O Module (PG-LND102) (2ports(1Gbps)) is applied. ) *9 Fibre channel Interfaces optional ( 2ports (2Gbps) when 2Gbit/s FC I/O Module (PG-FCD102) (2ports(2Gbps)) is applied. ) *10 Interfaces Display (Analog RGB) *11, USB x2(ver. 2.0) *11, Display *12, Keyboard *12, Mouse *12 Server Management Software ServerView (standard) Power supply Voltage DC12V / DC5V-Standby (provided by BX600 S2 Blade Server System Unit) Power consumption 405W / 1458kJ/h (max.) Dimensions (W x D x H (mm) ) 42 x 476 x 286 ( Server blade slot of BX600 S2 Blade Server System Unit x 1) Weight 7.0kg (max.) Environmental Conditions Temperature10-35 C / Humidity 20-80% (non condensing) OS Support *4 Windows Server 2003 R2, Standard Edition / Windows Server 2003 R2, Enterprise Edition Windows Server 2003, Standard Edition (SP1) / Windows Server 2003, Enterprise Edition (SP1) Windows Server 2003 R2, Standard x64 Edition / Windows Server 2003 R2, Enterprise x64 Edition Windows Server 2003, Standard x64 Edition / Windows Server 2003, Enterprise x64 Edition Windows 2000 Server (SP4) / Windows 2000 Advanced Server (SP4) Red Hat Enterprise Linux AS (v.3 for x86) *13 / Red Hat Enterprise Linux ES (v.3 for x86) *13 Red Hat Enterprise Linux AS (v.4 for x86) / Red Hat Enterprise Linux ES (v.4 for x86) Red Hat Enterprise Linux AS (v.4 for EM64T) / Red Hat Enterprise Linux ES (v.4 for EM64T) Attached tool (Standard) ServerStart (Setup Support tool) *14 *1.Available memory capacity will be changed by the type of OS. Please find more details in Notes[Memory OS Compatibility List]. *2. Resolution is determined by functions of the display monitor and OS. *3. HDD capacity is calculated according to the formula 1GB= byte *4. Drivers for Linux are not attached. Please download and use drivers of the following URL. *5. CPU Conversion kit: Xeon 5110(1.60GHz/4MB) -> Xeon X5355(2.66GHz/2x4MB) (PGBFU435) is available for upgrading to Quad Core Intel Xeon X GHz. *6. CPU Conversion kit: Xeon 5110(1.60GHz/4MB) -> Xeon E5310(1.60GHz/2x4MB) (PGBFU433) is available for upgrading to Quad Core Intel Xeon E GHz. *7. CPU Conversion kit: Xeon 5110(1.60GHz/4MB) -> Xeon 5160(3GHz/4MB) (PGBFU33T2) is available for upgrading to Intel Xeon GHz. *8. CPU Conversion kit: Xeon 5110(1.60GHz/4MB) -> Xeon 5130(2GHz/4MB) (PGBFU33S2) is available for upgrading to Intel Xeon GHz. *9. 1Gbit/s Ethernet I/O Module (PG-LND102) is available when Switch Blade (PG-SW104/PG-SW105) or GbE Pass-Thru Blade (PG-LNB102) or Cisco Catalyst Blade Switch 3040 (PG-SW106) are mounted on Network Blade Slot 3,4 of BX600 S2 Blade Server System Unit (PGUR3SC3). *10. 2Gbit/s FC I/O Module (PG-FCD102) is available when FC Switch Blade (PG-FCS102) or FC Pass-Thru Blade (PG-FCB102) are mounted on Network Blade Slot 3,4 of BX600 S2 Blade Server System Unit (PGUR3SC3). *11. Display, DVD-ROM and FDD can be connected to the Display/USB Extension connector of base unit with Display/USB Extension Cable(PG-CBLDP05). One Display/USB Extension Cable(PG-CBLDP05) is attached as standard with one BX600 S2 Blade Server System Unit (PGUR3SC3). *12. These are connected to KVM Module (standard) or KVM module (PG-KVB102) (optional) in BX600 S2 Blade Server System Unit (PGUR3SC3). *13. Quad Core Intel Xeon X5355 (2.66GHz) / E5310 (1.60GHz) are not included. *14. ServerStart doesn't support Linux.

5 Configuration Diagram Memory DIMM Slot 8 DIMM Slot 4 DIMM Slot 7 DIMM Slot 3 DIMM Slot 6 DIMM Slot 2 DIMM Slot 5 DIMM Slot 1 Expansion Board Slot *1,*2 CPU Xeon X5355 / E5310 / 5160 / 5130 / 5110 / LV 5148 Xeon X5355 / E5310 / 5160 / 5130 / 5110 / LV inch HDD Bay 1 (hot plug) 2.5 inch HDD Bay 2 (hot plug) Expansion Card Slot Module Hard Disk 2.5inch Bay (hot plug) Standard Drive Cage (HDD x 2ports) Bay 1 SAS Bay 2 SAS *1. When 2Gbit/s FC I/O Module (PG-FCD102) is mounted on Expansion Board Slot of BX620 S3, FC Switch Blade (PG-FCS102) or FC Pass-Thru Blade (PG-FCB102) is required to be mounted on Network Blade Slot 3,4 of BX600 S2 Blade Server System Unit (PGUR3SC3). *2. When 1Gbit/s Ethernet I/O Module (PG-LND102) is mounted on Expansion Board Slot of BX620 S3, Switch Blade (PG-SW104/PG-SW105) or GbE Pass-Thru Blade (PG-LNB102) or Cisco Catalyst Blade Switch 3040 (PG-SW106) are required to be mounted on Network Blade Slot 3,4 of BX600 S2 Blade Server System Unit (PGUR3SC3). *Components installed as standard configuration marked in grey. Mountable I/O Options BX620 S3 ( In case that Expansion Card Slot Module (PGBCS104) is applied. ) Mountable Cards Bus Max No. of Mount Remarks PG-2861L / Eth. Ctrl 2x1Gbit PCI-E 1000-BASE-T lp PCI Express (x4) 1 PGB2861L LowProfile PCI Express Card BX620 S3 ( In case that Expansion Card Slot Module (PGBCS103) is applied. ) Mountable Cards Bus Max No. of Mount Remarks SCSI Ctrl U160 lp PG-1301L / PGB1301L PCI/64bit 1 LowProfile PCI Card, For PRIMERGY SX10 *. PCI card (Eth. Ctrl 2x1Gbit PCI-E 1000-BASE-T lp (PG-2861L/PGB2861L)) should be mounted on Expansion Card Slot Module (PGBCS104). PCI card (SCSI Ctrl U160 lp (PG-1301L/PGB1301L)) should be mounted on Expansion Card Slot Module (PGBCS103). The slot of mounted PCI card is at front side of BX600 S2 Blade Server System Unit (PGUR3SC3). The cable connected to PCI card can be gone from front side to back side of BX600 S2 Blade Server System Unit (PGUR3SC3) by using Front-Rear Cable-Thru kit (PG-R1CM2). Front-Rear Cable-Thru kit (PG-R1CM2) is mounted just under BX620 S3 and occupies 1U.

6 Connection Table CPU CPU Slot Max: 2 CPU Processor Xeon X GHz/2x4MB PG-FG435 PGBFG435 (for CTO) *. This option is available when CPU Conversion Kit: Xeon 5110(1.60GHz/4MB) -> Xeon X5355(2.66GHz/2x4MB) (PGBFU435) is applied. Processor Xeon E GHz/2x4MB PG-FG433 PGBFG433 (for CTO) *. This option is available when CPU Conversion Kit: Xeon 5110(1.60GHz/4MB) -> Xeon E5310(1.60GHz/2x4MB) (PGBFU433) is applied. Processor Xeon GHz/4MB PG-FG33T PGBFG33T (for CTO) *. This option is available when CPU Conversion Kit: Xeon 5110(1.60GHz/4MB) -> Xeon 5160(3GHz/4MB) (PGBFU33T2) is applied. Processor Xeon GHz/4MB PG-FG33S PGBFG33S (for CTO) *. This option is available when CPU Conversion Kit: Xeon 5110(1.60GHz/4MB) -> Xeon 5130(2GHz/4MB) (PGBFU33S2) is applied. Processor Xeon GHz/4MB PG-FG33R PGBFG33R (for CTO) *. This option is available when the processor of the base unit is Processor Xeon 5110(1.60GHz/4MB). Processor Xeon GHz/4MB PG-FG33V PGBFG33V (for CTO) *. This option is available when the processor of the base unit is Processor Xeon 5148(2.33GHz/4MB). *CPU Conversion Kit (available only for a Configure to Order (CTO) option; no separate shipment is possible) Type Product ID CPU Conversion Kit: Dual Core Intel Xeon 5110(1.60GHz/4MB) -> Dual Core Intel Xeon X5355(2.66GHz/2x4MB) Xeon 5110(1.60GHz/4MB) Convert the CPU installed as standard in the base unit to the other. PGBFU435 -> Xeon X5355(2.66GHz/2x4MB) (Note: This option can be ordered only as coupled with the base unit. (for CTO) A separate shipment is not possible.) CPU Conversion Kit: Dual Core Intel Xeon 5110(1.60GHz/4MB) -> Dual Core Intel Xeon E5310(1.60GHz/2x4MB) Xeon 5110(1.60GHz/4MB) PGBFU433 Convert the CPU installed as standard in the base unit to the other. -> Xeon E5310(1.60GHz/2x4MB) (Note: This option can be ordered only as coupled with the base unit. (for CTO) A separate shipment is not possible.) CPU Conversion Kit: Dual Core Intel Xeon 5110(1.60GHz/4MB) -> Dual Core Intel Xeon 5160 (3GHz) Xeon 5110(1.60GHz/4MB) PGBFU33T2 Convert the CPU installed as standard in the base unit to the other. -> Xeon 5160(3GHz/4MB) (Note: This option can be ordered only as coupled with the base unit. (for CTO) A separate shipment is not possible.) CPU Conversion Kit: Dual Core Intel Xeon 5110(1.60GHz/4MB) -> Dual Core Intel Xeon 5130(2GHz) Xeon 5110(1.60GHz/4MB) PGBFU33S2 Convert the CPU installed as standard in the base unit to the other. -> Xeon 5130(2GHz/4MB) (Note: This option can be ordered only as coupled with the base unit. (for CTO) A separate shipment is not possible.)

7 Memory (PC2 5300F) Memory Slot Max: 32GB (4GB FB-DIMM x 8) Memory Module-1GB (512MB FB-DIMM x 2) PG-RM1CE Standard Memory Module: 1GB (512MB FB-DIMM x 2) Memory Module-2GB (1GB FB-DIMM x 2) PG-RM2CE Memory Module-4GB (2GB FB-DIMM x 2) PG-RM4CE Memory Module-8GB (4GB FB-DIMM x 2) PG-RM8CE Memory Slot Memory Module Conversion kit (for CTO) Memory Module Conversion kit-2gb (1GB FB-DIMM x 2) PGBRU2CE (for CTO) Memory Module Conversion kit-4gb (2GB FB-DIMM x 2) PGBRU4CE (for CTO) Memory Module Conversion kit-8gb (4GB FB-DIMM x 2) PGBRU8CE (for CTO) * Notes on installing memory 1. Memory is installed by pairs of FB-DIMMs of the same capacity. Installation of one FB-DIMM or a mixed -capacity pair is impossible. 2. The memory capacities of the slots should be in ascending order in the following sequence: DIMM slots 1,2 (Bank 1) -> DIMM slots 3,4 (Bank 2) -> DIMM slots 5,6 (Bank 3) -> DIMM slots 7,8 (Bank 4) (Available Memory Area) Windows 2000 Server (SP4) Windows 2000 Advanced Server (SP4) Others Mounted Memory ~3.0GB 4.0GB ~7.0GB 8.0GB ~32.0GB Available Memory Area Same as the size of mounted memory Size of Mounted Memory minus "1.0GB" Same as the size of mounted memory Size of Mounted Memory minus "1.0GB" Same as the size of mounted memory *. Memory Mirroring Function In case of using Memory Mirroring Function, the following conditions are required. (1) FB-DIMM x 4 or FB-DIMM x 8 should be installed. (2) Memory capacity of each memory pair should be same. (3) Available memory capacity is half of installed memory. Connecting Internal HDD and Internal Backup Devices Internal HDD SAS/RAID Configuration Onboard SAS Controller Max: 2 HDDs *. RAID1 configuration can be set. HDD SAS 10k 36GB hot plug 2.5inch PG-HDD61A PGBHDD61A (for CTO) HDD SAS 10k 73GB hot plug 2.5inch PG-HDD71A PGBHDD71A (for CTO)

8 LAN Card/Internal backup device (PRIMERGY SX10) Max: 1 Expansion Card Slot Module Connector Twist Pair Cable (category 5e) Expansion Card Slot Module PGBCS104 (for CTO) Eth. Ctrl 2x1Gbit PCI-E 1000-BASE-T lp PG-2861L PGB2861L (for CTO) *Dual port SCSI Cable HDCI 1.8m PRIMERGY SX10 Expansion Card Slot Module SCSI Ctrl U160 lp PG-CBLS007 PG-R1BC4 PGBCS103 (for CTO) PG-1301L SCSI Cable HDCI 5m PGB1301L (for CTO) PG-CBLS008 Notes on applying Expansion Card Slot Module (PGBCS103/PGBCS104) In case that Expansion Card Slot Module (PGBCS103/PGBCS104) is mounted on BX620 S3, and PCI card is monted on Expansion Card Slot Module, the slot of mounted PCI card is at front side of BX600 S2 Blade Server System Unit (PGUR3SC3). The cable connected to PCI card can be gone from front side to back side of BX600 S2 Blade Server System Unit (PGUR3SC3) by using Front-Rear Cable-Thru kit (PG-R1CM2). Front-Rear Cable-Thru kit (PG-R1CM2) is mounted just under BX620 S3 and occupies 1U. Front-Rear Cable-Thru kit PG-R1CM2 LAN/Fibre Channel Interface On-board LAN Interface Switch Blade / GbE Pass-Thru Blade / Cisco Catalyst Blade Switch 3040 Expansion Board Slot Max: 1 1Gbit/s Ethernet I/O Module PG-LND102 Switch Blade / PGBLND102 (for CTO) GbE Pass-Thru Blade / Cisco Catalyst Blade Switch Gbit/s FC I/O Module PG-FCD102 FC Switch Blade / PGBFCD102 (for CTO) FC Pass-Thru Blade DVD-ROM/FDD/Display Display/USB Extension connector DVD-ROM/FDD/Display Display/USB Extension Cable PG-CBLDP05

9 Switch Blade Data Sheet Type Switch Blade Base Unit PG-SW104 PG-SW105 CTO optional PGBSW1040 (*1) / PGBSW1041 (*2) / PGBSW1042 (*3) / PGBSW1043 (*4) PGBSW1050 (*1) / PGBSW1051 (*2) / PGBSW1052 (*3) / PGBSW1053 (*4) LAN Interfaces Internal 10ports (1Gbps) 10ports (1Gbps) 6ports (1000BASE-T / 100BASE-TX / 10BASE-T), External 6ports (1000BASE-T / 100BASE-TX / 10BASE-T) 1port (10GBASE-SR), 1port (10GBASE-CX4) Dimensions (W x D x H (mm) ) 35 x 250 x x 250 x 130 *1. This is the type of Switch Blade which is mounted on Network Blade Slot 1 of BX600 S2 Blade Server System Unit. *2. This is the type of Switch Blade which is mounted on Network Blade Slot 2 of BX600 S2 Blade Server System Unit. When Switch Blade (PGBSW1041) is ordered, Switch Blade (PGBSW1040) or Switch Blade (PGBSW1050) or GbE Pass-Thru Blade(PGBLNB1020) or Cisco Catalyst Blade Switch 3040 (PGBSW1060) should be ordered at a time. When Switch Blade (PGBSW1051) is ordered, Switch Blade (PGBSW1040) or Switch Blade (PGBSW1050) or GbE Pass-Thru Blade(PGBLNB1020) or Cisco Catalyst Blade Switch 3040 (PGBSW1060) should be ordered at a time. *3. This is the type of Switch Blade which is mounted on Network Blade Slot 3 of BX600 S2 Blade Server System Unit. *4. This is the type of Switch Blade which is mounted on Network Blade Slot 4 of BX600 S2 Blade Server System Unit. When Switch Blade (PGBSW1043) is ordered, Switch Blade (PGBSW1042) or Switch Blade (PGBSW1052) or GbE Pass-Thru Blade(PGBLNB1022) or Cisco Catalyst Blade Switch 3040 (PGBSW1062) should be ordered at a time. When Switch Blade (PGBSW1053) is ordered, Switch Blade (PGBSW1042) or Switch Blade (PGBSW1052) or GbE Pass-Thru Blade(PGBLNB1022) or Cisco Catalyst Blade Switch 3040 (PGBSW1062) should be ordered at a time. *. When Switch Blade (PG-SW104/PG-SW105) are mounted on Network Blade Slot 3,4 of BX600 S2 Blade Server System Unit (PGUR3SC3), the card on Expansion Board Slot of BX620 S3 should be 1Gbit/s Ethernet I/O Module(PG-LND102). *. In case of using 10GBASE-SR connection of Switch Blade (PG-SW105), XFP Module (PG-XFPS01) is required. GbE Pass-Thru Blade Data Sheet Base Unit Type GbE Pass-Thru Blade PG-LNB102 CTO optional PGBLNB1020 (*1) / PGBLNB1021 (*2) / PGBLNB1022 (*3) / PGBLNB1023 (*4) LAN Interfaces Internal 10ports (1Gbps) (*5) External 10ports (1000BASE-T) (fixed) (*5) Dimensions (W x D x H (mm) ) 35 x 250 x 130 *1. This is the type of GbE Pass-Thru Blade which is mounted on Network Blade Slot 1 of BX600 S2 Blade Server System Unit. *2. This is the type of GbE Pass-Thru Blade which is mounted on Network Blade Slot 2 of BX600 S2 Blade Server System Unit. When GbE Pass-Thru Blade (PGBLNB1021) is ordered, Switch Blade (PGBSW1040) or Switch Blade (PGBSW1050) or GbE Pass-Thru Blade(PGBLNB1020) or Cisco Catalyst Blade Switch 3040 (PGBSW1060) should be ordered at a time. *3. This is the type of GbE Pass-Thru Blade which is mounted on Network Blade Slot 3 of BX600 S2 Blade Server System Unit. *4. This is the type of GbE Pass-Thru Blade which is mounted on Network Blade Slot 4 of BX600 S2 Blade Server System Unit. When GbE Pass-Thru Blade (PGBLNB1023) is ordered, Switch Blade (PGBSW1042) or Switch Blade (PGBSW1052) or GbE Pass-Thru Blade(PGBLNB1022) or Cisco Catalyst Blade Switch 3040 (PGBSW1062) should be ordered at a time. *5. Connections between internal ports and external ports are one-to-one. *. To connect to hub/router through GbE Pass-Thru Blade, it is necessary to connect to the port of 1000BASE-T(fixed). In case that the port of 10/100BASE-TX is connected, communication cannot be established. *. When GbE Pass-Thru Blade (PG-LNB102) are mounted on Network Blade Slot 3,4 of BX600 S2 Blade Server System Unit (PGUR3SC3), the card on Expansion Board Slot of BX620 S3 should be 1Gbit/s Ethernet I/O Module(PG-LND102).

10 Cisco Catalyst Blade Switch 3040 Data Sheet Base Unit Type Cisco Catalyst Blade Switch 3040 PG-SW106 CTO optional PGBSW1060 (*1) / PGBSW1061 (*2) / PGBSW1062 (*3) / PGBSW1063 (*4) LAN Interfaces Internal 10ports (1Gbps) External 2ports (1000BASE-T / 100BASE-TX / 10BASE-T) SFP slot 4 Dimensions (W x D x H (mm) ) 35 x 250 x 130 *1. This is the type of Cisco Catalyst Blade Switch 3040 which is mounted on Network Blade Slot 1 of BX600 S2 Blade Server System Unit. *2. This is the type of Cisco Catalyst Blade Switch 3040 which is mounted on Network Blade Slot 2 of BX600 S2 Blade Server System Unit. When Cisco Catalyst Blade Switch 3040 (PGBSW1061) is ordered, Switch Blade (PGBSW1040) or Switch Blade (PGBSW1050) or GbE Pass-Thru Blade(PGBLNB1020) or Cisco Catalyst Blade Switch 3040 (PGBSW1060) should be ordered at a time. *3. This is the type of Cisco Catalyst Blade Switch 3040 which is mounted on Network Blade Slot 3 of BX600 S2 Blade Server System Unit. *4. This is the type of Cisco Catalyst Blade Switch 3040 which is mounted on Network Blade Slot 4 of BX600 S2 Blade Server System Unit. When Cisco Catalyst Blade Switch 3040 (PGBSW1063) is ordered, Switch Blade (PGBSW1042) or Switch Blade (PGBSW1052) or GbE Pass-Thru Blade(PGBLNB1022) or Cisco Catalyst Blade Switch 3040 (PGBSW1062) should be ordered at a time. *. When Cisco Catalyst Blade Switch 3040 (PG-SW106) are mounted on Network Blade Slot 3,4 of BX600 S2 Blade Server System Unit (PGUR3SC3), the card on Expansion Board Slot of BX620 S3 should be 1Gbit/s Ethernet I/O Module(PG-LND102). *. In case of using SFP slot of Cisco Catalyst Blade Switch 3040 (PG-SW106), 1000BASE-T SFP (PG-SFPC01) or 1000BASE-SX SFP (PG-SFPS03) is required.

11 FC Switch Blade Data Sheet Base Unit Type FC Switch Blade PG-FCS102 CTO optional PGBFCS102 (*1) / PGBFCS1022 (*2) Fibre Channel Internal 8ports (4Gbps) ( 10ports (2Gbps when FCSW Upgrade kit:porton Demand (PG-FCSU102) is applied ) Interfaces External 4ports (4Gbps, Fibre Channel) ( 6ports (4Gbps, Fibre Channel) when FCSW Upgrade kit:porton Demand (PG-FCSU102) is applied ) Dimensions (W x D x H (mm) ) 35 x 250 x 130 *1. This is the type of FC Switch Blade which is mounted on Network Blade Slot 3 of BX600 S2 Blade Server System Unit. *2. This is the type of FC Switch Blade which is mounted on Network Blade Slot 4 of BX600 S2 Blade Server System Unit. When FC Switch Blade (PGBFCS1022) is ordered, FC Switch Blade (PGBFCS102) or FC Pass-Thru Blade (PGBFCB102) should be ordered at a time. *. The max number of available ports under initial condition is as follows. internal : 8ports external : 4ports If it is necessary to connect more than 8 BX620 S3, FCSW Upgrade kit:porton Demand(PG-FCSU102) is required to increase available ports. *. When FC Switch Blade (PG-FCS102) are mounted on Network Blade Slot 3,4 of BX600 S2 Blade Server System Unit (PGUR3SC3), the card on Expansion Board Slot of BX620 S3 should be 2Gbit/s FC I/O Module (PG-FCD102). *. SFP Module (PG-SFPS02), whose number is same as that of used external ports, should be ordered. FC Pass-Thru Blade Data Sheet Base Unit Type FC Pass-Thru Blade PG-FCB102 CTO optional PGBFCB102 (*1) / PGBFCB1022 (*2) Fibre Channel Internal 10ports (2Gbps) (*3) Interfaces External 10ports (2Gbps,Fibre Channel) (*3) Dimensions (W x D x H (mm) ) 35 x 250 x 130 *1. This is the type of FC Pass-Thru Blade which is mounted on Network Blade Slot 3 of BX600 S2 Blade Server System Unit. *2. This is the type of FC Pass-Thru Blade which is mounted on Network Blade Slot 4 of BX600 S2 Blade Server System Unit. When FC Pass-Thru Blade (PGBFCB1022) is ordered, FC Switch Blade (PGBFCS102) or FC Pass-Thru Blade (PGBFCB102) should be ordered at a time. *3. Connections between internal ports and external ports are one-to-one. *. When FC Pass-Thru Blade (PG-FCB102) are mounted on Network Blade Slot 3,4 of BX600 S2 Blade Server System Unit (PGUR3SC3), the card on Expansion Board Slot of BX620 S3 should be 2Gbit/s FC I/O Module (PG-FCD102). *. SFP Module (PG-SFPS01), whose number is same as that of used external ports, should be ordered.

12 BX600 S2 Blade Server System Unit Data Sheet Type BX600 S2 Blade Server System Unit Base Unit PGUR3SC3 Slots Server Blade 10 (hot plug) (*1) Network Blade 4 (hot plug) (LAN/Fibre Channel) Management Blade (standard) 2 (Management Bladex2 standard) (hot plug) KVM Module Display (Analog RGB) (*2), Keyboard (PS/2type Mini DIN 6pins) (*2), Mouse (PS/2type Mini DIN 6pins) (*2) ( KVM Module x 1 installed as standard ) Power supply Voltage AC200V(50/60Hz) (NEMA L6-30)x 2 (Max. 4) Power consumption 5600W / 20160kJ/h (max.) Redundant power supply optional (hot plug) Redundant Fan standard (hot plug) Dimensions (W x D x H (mm) ) 446(483 incl. protruding parts) x 735(800 incl. protruding parts) x 308(7U) Weight 130kg (max.) *1. One BX620 S3 occupies One Server Blade Slot. *2. Display, Keyboard and Mouse can be connected by using Display/PS/2 Extension Cable attached as standard with one BX600 S2 Blade Server System Unit (PGUR3SC3). *. When BX600 S2 Blade Server System Unit (PGUR3SC3) is ordered, Switch Blade (PGBSW1040) or Switch Blade (PGBSW1050) or GbE Pass-Thru Blade(PGBLNB1020) or Cisco Catalyst Blade Switch 3040 (PGBSW1060) should be ordered at a time. Configuration Diagram Network Blade Slot 2 Network Blade Slot 1 Server Blade Slot 1 Server Blade Slot 2 Server Blade Slot 3 Server Blade Slot 4 Server Blade Slot 5 Server Blade Slot 6 Server Blade Slot 7 Server Blade Slot 8 Server Blade Slot 9 Server Blade Slot 10 Network Blade Slot 4 Network Blade Slot 3 Power Supply Unit 4 Power Supply Unit 3 Management Blade 2 Management Blade 1 KVM Module Power Supply Unit 2 Power Supply Unit 1 Front View Back View *Components installed as standard configuration marked in grey.

13 BX600 S2 Blade Server System Unit Connection Table BX600 S2 Blade Server System Unit PGUR3SC3 Server Blade Server Blade Slots Max: 10 BX620 S3 Notes on addition of BX620 S3 In case that BX620 S3 are added on BX600 S2 Blade Server System Unit (PGUR3SC1/PGUR3SC3), it may be necessary to change firmware version of Management Blade of BX600 S2 Blade Server System Unit (PGUR3SC1/PGUR3SC3). For details, please refer to accompanying material of BX620 S3. LAN Interfaces ( Use of Network Blade Slot 1,2 ) Network Blade Slots Max: 2 Blades Switch Blade PG-SW104 Twist Pair Cable (category 5e) PGBSW1040 (for CTO) (for Network Blade Slot 1) PGBSW1041 (for CTO) (for Network Blade Slot 2) Switch Blade ( 1000BASE-T ) PG-SW105 Twist Pair Cable (category 5e) PGBSW1050 (for CTO) (for Network Blade Slot 1) PGBSW1051 (for CTO) ( 10GBASE-SR ) XFP Module Multi Mode Fibre Channel Cable (for Network Blade Slot 2) PG-XFPS01 ( 10GBASE-CX4 ) IB Cable GbE Pass-Thru Blade PG-LNB102 Twist Pair Cable (category 5e) PGBLNB1020 (for CTO) (for Network Blade Slot 1) PGBLNB1021 (for CTO) (for Network Blade Slot 2) Cisco Catalyst Blade Switch 3040 PG-SW106 Twist Pair Cable (category 5e) PGBSW1060 (for CTO) (for Network Blade Slot 1) PGBSW1061 (for CTO) 1000BASE-T SFP Twist Pair Cable (category 5e) (for Network Blade Slot 2) PG-SFPC01 4 slots 1000BASE-SX SFP Multi Mode Fibre Channel Cable PG-SFPS03 Notes on Switch Blade (PG-SW104/PG-SW105) In case that Switch Blade are added on old BX600 S2 Blade Server System Unit (PGUR3SC1), it is necessary to change firmware version of Management Blade of BX600 S2 Blade Server System Unit (PGUR3SC1). Notes on GbE Pass-Thru Blade (PG-LNB102) * To connect to hub/router through GbE Pass-Thru Blade, it is necessary to connect to the port of 1000BASE-T(fixed). In case that the port of 10/100BASE-TX is connected, communication cannot be established. Notes on Cisco Catalyst Blade Switch 3040 (PG-SW106) In case that Cisco Catalyst Blade Switch 3040 are added on old BX600 S2 Blade Server System Unit (PGUR3SC1/PGUR3SC3), it is necessary to change firmware version of Management Blade of BX600 S2 Blade Server System Unit (PGUR3SC1/PGUR3SC3).

14 BX600 S2 Blade Server System Unit LAN/Fibre Channel Interfaces ( Use of Network Blade Slot 3,4 ) Network Blade Slots Max: 2 Blades Switch Blade PG-SW104 Twist Pair Cable (category 5e) PGBSW1042 (for CTO) (for Network Blade Slot 3) PGBSW1043 (for CTO) (for Network Blade Slot 4) Switch Blade ( 1000BASE-T ) PG-SW105 Twist Pair Cable (category 5e) PGBSW1052 (for CTO) (for Network Blade Slot 3) PGBSW1053 (for CTO) ( 10GBASE-SR ) XFP Module Multi Mode Fibre Channel Cable (for Network Blade Slot 4) PG-XFPS01 ( 10GBASE-CX4 ) IB Cable GbE Pass-Thru Blade PG-LNB102 Twist Pair Cable (category 5e) PGBLNB1022 (for CTO) (for Network Blade Slot 3) PGBLNB1023 (for CTO) (for Network Blade Slot 4) Cisco Catalyst Blade Switch 3040 PG-SW106 Twist Pair Cable (category 5e) PGBSW1062 (for CTO) (for Network Blade Slot 3) PGBSW1063 (for CTO) 1000BASE-T SFP Twist Pair Cable (category 5e) (for Network Blade Slot 4) PG-SFPC01 4 slots 1000BASE-SX SFP Multi Mode Fibre Channel Cable PG-SFPS03 FC Switch Blade PG-FCS102 SFP Module Multi Mode Fibre Channel Cable PGBFCS102 (for CTO) PG-SFPS02 (for Network Blade Slot 3) PGBFCS1022 (for CTO) (for Network Blade Slot 4) FCSW Upgrade kit:porton Demand ( internal : 8 ports -> 10 ports external : 4ports -> 6ports ) PG-FCSU102 FCSW Upgrade kit:isl Trunking PG-FCSU103 FC Pass-Thru Blade PG-FCB102 SFP Module Multi Mode Fibre Channel Cable PGBFCB102 (for CTO) PG-SFPS01 (for Network Blade Slot 3) PGBFCB1022 (for CTO) (for Network Blade Slot 4) Notes on Switch Blade (PG-SW104/PG-SW105) In case that Switch Blade are added on old BX600 S2 Blade Server System Unit (PGUR3SC1), it is necessary to change firmware version of Management Blade of BX600 S2 Blade Server System Unit (PGUR3SC1). Notes on GbE Pass-Thru Blade (PG-LNB102) * To connect to hub/router through GbE Pass-Thru Blade, it is necessary to connect to the port of 1000BASE-T(fixed). In case that the port of 10/100BASE-TX is connected, communication cannot be established. Notes on Cisco Catalyst Blade Switch 3040 (PG-SW106) In case that Cisco Catalyst Blade Switch 3040 are added on old BX600 S2 Blade Server System Unit (PGUR3SC1/PGUR3SC3), it is necessary to change firmware version of Management Blade of BX600 S2 Blade Server System Unit (PGUR3SC1/PGUR3SC3).

15 BX600 S2 Blade Server System Unit Notes on FC Switch Blade (PG-FCS102) * The max number of available ports under initial condition is as follows. internal : 8ports external : 4ports * If it is necessary to connect more than 8 BX620 S3, FCSW Upgrade kit:porton Demand(PG-FCSU102) is required to increase available ports. * In case that FC Switch Blade are added on old BX600 S2 Blade Server System Unit (PGUR3SC1), it is necessary to change firmware version of Management Blade of BX600 S2 Blade Server System Unit (PGUR3SC1). For details, please refer to accompanying material of FC Switch Blade. Connection between BX620 S3 and Network Blade Please refer to the following connection patterns between BX620 S3 and Network Blade. BX620 S3 Structure Interface LAN Onboard LAN + LAN 1Gbit/s Ethernet I/O Module (optional) cannot be mounted with 2Gbit/s FC I/O Module (*) + Fibre Channel 2Gbit/s FC I/O Module (optional) cannot be mounted with 1Gbit/s Ethernet I/O Module (*) Port Port 1 Port 2 Port 1 Port 2 Port 1 Port 2 Network Blade Switch Blade / GbE Pass-Thru Blade / FC Switch Blade / FC Pass-Thru Blade Network Blade 1 (optional : Switch Blade (PG-SW104/PGBSW1040/PG-SW105/PGBSW1050) / GbE Pass-Thru Blade(PG-LNB102/PGBLNB1020) / Cisco Catalyst Blade Switch 3040 (PG-SW106/PGBSW1060) ) Network Blade 2 (optional : Switch Blade (PG-SW104/PGBSW1041/PG-SW105/PGBSW1051) / GbE Pass-Thru Blade(PG-LNB102/PGBLNB1021) / Cisco Catalyst Blade Switch 3040 (PG-SW106/PGBSW1061) ) Network Blade 3 (optional : Switch Blade (PG-SW104/PGBSW1042/PG-SW105/PGBSW1052) / GbE Pass-Thru Blade(PG-LNB102/PGBLNB1022) / Cisco Catalyst Blade Switch 3040 (PG-SW106/PGBSW1062) ) Network Blade 4 (optional : Switch Blade (PG-SW104/PGBSW1043/PG-SW105/PGBSW1053) / GbE Pass-Thru Blade(PG-LNB102/PGBLNB1023) / Cisco Catalyst Blade Switch 3040 (PG-SW106/PGBSW1063) ) Network Blade 3 (optional : FC Switch Blade (PG-FCS102/PGBFCS102) / FC Pass-Thru Blade (PG-FCB102/PGBFCB102) ) Network Blade 4 (optional : FC Switch Blade (PG-FCS102/PGBFCS1022) / FC Pass-Thru Blade (PG-FCB102/PGBFCB1022) ) * KVM Module (KVM Switch) KVM Module Slot PRIMERGY BX600 KVM Module Display/Keyboard/Mouse Max: 1 Standard: 1 Unit Display/Keyboard/Mouse KVM Module Conversion kit PGBKVU102 KVM Module PG-KVB102 Twist Pair Cable HUB Twist Pair Cable PRIMERGY BX600 Management Blade Notes on KVM Module (PG-KVB102) * KVM Module (PG-KVB102), PRIMERGY BX600 Management Blade and Client PC are connected to same network.

16 BX600 S2 Blade Server System Unit Management Blade Management Blade Slots Max: 2 Blades PRIMERGY BX600 RS-232C Cross Cable Operator Client Standard: 2 Blades Management Blade * for setting Management Blade * one cable attached with BX600 S2 Blade Server System Unit (PGUR3SC3) as standard. Twist Pair Cable HUB Supervisor Client Power Supply Unit Power Supply Unit Slots Max: 4 Units Standard: 2 Units Power Supply Module PG-PU121 PGBPU121 (for CTO) * 2 Units AC Plug Outlet Specifications are subject to change without notice. For the latest detailed information, contact your local representative. All brand names and product names are trademarks and registered trademarks of their respective holders Fujitsu Limited. All rights reserved. Printed in Japan. Global Business Development & Marketing Business Strategy & Planning System Products URL