SICAM SICAM FCM Configurator

Transcription

1 Preface Open Source Software SICAM SICAM FCM Configurator Table of Contents SICAM FCM Configurator 1 Index V02.10 Configuration and Operation E50417-H8940-C592-A3

2 i NOTE For your own safety, observe the warnings and safety instructions contained in this document, if available. Disclaimer of Liability This document has been subjected to rigorous technical review before being published. It is revised at regular intervals, and any modifications and amendments are included in the subsequent issues. The content of this document has been compiled for information purposes only. Although Siemens AG has made best efforts to keep the document as precise and up-to-date as possible, Siemens AG shall not assume any liability for defects and damage which result through use of the information contained herein. This content does not form part of a contract or of business relations; nor does it change these. All obligations of Siemens AG are stated in the relevant contractual agreements. Siemens AG reserves the right to revise this document from time to time. Document version: E50417-H8940-C592-A3.01 Edition: Version of the product described: V02.10 Copyright Copyright Siemens AG All rights reserved. The disclosure, duplication, distribution and editing of this document, or utilization and communication of the content are not permitted, unless authorized in writing. All rights, including rights created by patent grant or registration of a utility model or a design, are reserved. Registered Trademarks SIPROTEC, DIGSI, SIGUARD, SIMEAS, and SICAM are registered trademarks of Siemens AG. Any unauthorized use is illegal. All other designations in this document can be trademarks whose use by third parties for their own purposes can infringe the rights of the owner.

3 Preface Purpose of the Manual This manual describes the application, functions, installation, and operation of the SICAM FCM Configurator. Target Audience Protection system engineers, commissioning engineers, persons entrusted with the setting, testing and maintenance of automation, selective protection and control equipment, and operational crew in electrical installations and power plants. Scope This manual applies to the SICAM FCM Configurator. Other Standards IEC/EN : IEC/EN : Support Our Customer Support Center provides a 24-hour service. Phone: +49 (180) Fax: +49 (180) support.energy@siemens.com Additional Support For questions about the system, please contact your Siemens sales partner. Training Courses Inquiries regarding individual training courses should be addressed to our Training Center: Siemens AG Siemens Power Academy TD Humboldtstraße Nürnberg Germany Phone: +49 (911) Fax: +49 (911) poweracademy@siemens.com Internet: SICAM, SICAM FCM Configurator, Configuration and Operation 3

4 Preface Notes on Safety This document is not a complete index of all safety measures required for operation of the equipment (module or device). However, it comprises important information that must be followed for personal safety, as well as to avoid material damage. Information is highlighted and illustrated as follows according to the degree of danger:! DANGER DANGER means that death or severe injury will result if the measures specified are not taken. ² Comply with all instructions, in order to avoid death or severe injuries.! WARNING WARNING means that death or severe injury may result if the measures specified are not taken. ² Comply with all instructions, in order to avoid death or severe injuries.! CAUTION CAUTION means that medium-severe or slight injuries can occur if the specified measures are not taken. ² Comply with all instructions, in order to avoid moderate or minor injuries. NOTICE NOTICE means that property damage can result if the measures specified are not taken. ² Comply with all instructions, in order to avoid property damage. i NOTE Important information about the product, product handling or a certain section of the documentation which must be given particular attention. 4 SICAM, SICAM FCM Configurator, Configuration and Operation

5 Open Source Software The product contains, among other things, Open Source Software developed by third parties. The Open Source Software used in the product and the license agreements concerning this software can be found in the Readme_OSS. These Open Source Software files are protected by copyright. Your compliance with those license conditions will entitle you to use the Open Source Software as foreseen in the relevant license. In the event of conflicts between Siemens license conditions and the Open Source Software license conditions, the Open Source Software conditions shall prevail with respect to the Open Source Software portions of the software. The Open Source Software is licensed royalty-free. Insofar as the applicable Open Source Software License Conditions provide for it you can order the source code of the Open Source Software from your Siemens sales contact - against payment of the shipping and handling charges - for a period of at least 3 years since purchase of the Product. We are liable for the Product including the Open Source Software contained in it pursuant to the license conditions applicable to the Product. Any liability for the Open Source Software beyond the program flow intended for the Product is explicitly excluded. Furthermore any liability for defects resulting from modifications to the Open Source Software by you or third parties is excluded. We do not provide any technical support for the Product if it has been modified. SICAM, SICAM FCM Configurator, Configuration and Operation 5

6 6 SICAM, SICAM FCM Configurator, Configuration and Operation

7 Table of Contents Preface...3 Open Source Software SICAM FCM Configurator Overview Hardware Configuration Requirements Installation Connecting SICAM FCM with USB to Serial (RS485) Converter Control Elements and Control Functions Starting the SICAM FCM Configurator User Interface Dashboard SICAM FCM Configurator Dashboard Reports and Monitoring Group Reports Group Monitoring Group Parameter Settings Backup Device Settings Restore Device Settings Update Firmware Log off SICAM FCM Configurator Uninstallation...42 Index...45 SICAM, SICAM FCM Configurator, Configuration and Operation 7

8 8 SICAM, SICAM FCM Configurator, Configuration and Operation

9 1 SICAM FCM Configurator 1.1 Overview Hardware Configuration Requirements Installation Connecting SICAM FCM with USB to Serial (RS485) Converter Control Elements and Control Functions Starting the SICAM FCM Configurator User Interface Dashboard Parameter Settings Backup Device Settings Restore Device Settings Update Firmware Log off SICAM FCM Configurator Uninstallation 42 SICAM, SICAM FCM Configurator, Configuration and Operation 9

10 1.1 Overview 1.1 Overview SICAM FCM Configurator is a Web-based configurator which allows you to configure and apply the parameters to the SICAM FCM device. The main functions of SICAM FCM Configurator are: Update the SICAM FCM firmware Configure and apply the engineering parameter settings to the SICAM FCM device Read the parameter settings from SICAM FCM device and save the settings in.xml file Restore the device settings from the stored backup settings Display the following device information: SICAM FCM firmware version Boot-loader version Application software version Display the device health state Monitor and display the events and trailing pointer values Monitor and display the following: Current Voltage Power Energy 10 SICAM, SICAM FCM Configurator, Configuration and Operation

11 1.2 Hardware Configuration Requirements 1.2 Hardware Configuration Requirements Before installing and operating the SICAM FCM Configurator, ensure that your personal computer (PC) or laptop computer is equipped with the following minimum hardware specifications and the operating system. 1-GHz processor or higher 1 GB of free storage capacity on the hard disk 1 GB of RAM (2 GB recommended) Graphic display with a resolution of 1024 x 768 pixels (1280 x 1024 pixels recommended) USB to serial (RS485) converter/rs232 to RS485 converter Operating system: Windows 7 (64 bit)/win2008 Server R2 You cannot install and operate the SICAM FCM Configurator with the following operating systems: Microsoft Windows XP and older operating systems Microsoft Windows 7 Starter, Home Basic, Home Premium Microsoft Windows Server 2003 SICAM, SICAM FCM Configurator, Configuration and Operation 11

12 1.3 Installation 1.3 Installation Before installing the SICAM FCM Configurator on the PC or laptop computer, download the SICAM FCM Configurator (Setup.exe) from the following Siemens internet page: To install the SICAM FCM Configurator, proceed as follows: ² Double-click the Setup.exe. If the SICAM FCM Configurator is already installed in the PC or laptop computer, the following Welcome Setup screen appears. In this process, the existing version of configurator is automatically removed and initiates upgrade to SICAM FCM Configurator. [sc_fcm_welcome upgrade, 1, --_--] Figure 1-1 SICAM FCM Configurator Setup Welcome Screen Upgrade The following Welcome Setup screen appears if the SICAM FCM Configurator is installed for first time. 12 SICAM, SICAM FCM Configurator, Configuration and Operation

13 1.3 Installation [sc_fcm_welcome screen, 1, --_--] Figure 1-2 SICAM FCM Configurator Setup Welcome Screen ² Click Next > to install the SICAM FCM Configurator in the destination folder. Siemens recommends keeping the SICAM FCM Configurator installation in the default folder C:\Program Files (x86)\siemens Energy\SICAM FCM Configurator\. [sc_fcm_destination folder, 1, --_--] Figure 1-3 SICAM FCM Configurator Setup Destination Folder ² Click Next > to begin the SICAM FCM Configurator installation. SICAM, SICAM FCM Configurator, Configuration and Operation 13

14 1.3 Installation [sc_fcm_ready to install, 1, --_--] Figure 1-4 SICAM FCM Configurator Setup Ready to Install ² Click Install to start the SICAM FCM Configurator installation. [sc_fcm_install inprogress, 1, --_--] Figure 1-5 SICAM FCM Configurator Setup Installation in Progress 14 SICAM, SICAM FCM Configurator, Configuration and Operation

15 1.3 Installation [sc_fcm_install complete, 1, --_--] Figure 1-6 SICAM FCM Configurator Setup Installation Finished ² Click Finish to complete the SICAM FCM Configurator installation. Launching the SICAM FCM Configurator To launch the SICAM FCM Configurator, proceed as follows: ² Double-click the SICAM FCM Configurator icon from the desktop to open the SICAM FCM Configurator. - or - ² Select Start Menu All Programs Siemens Energy SICAM FCM Configurator. [sc_fcm_installstart_ , 1, en_us] SICAM, SICAM FCM Configurator, Configuration and Operation 15

16 1.4 Connecting SICAM FCM with USB to Serial (RS485) Converter 1.4 Connecting SICAM FCM with USB to Serial (RS485) Converter If you are installing the SICAM FCM Configurator for the first time, install the USB to serial (RS485) converter drivers on your PC or laptop computer. Before starting the SICAM FCM Configurator user interface, connect the SICAM FCM with the USB to a serial (RS485) converter which provides the connectivity and interfaces. To connect the SICAM FCM with the USB to serial (RS485) converter, proceed as follows: ² Connect the USB end of the USB to serial (RS485) converter to the PC or laptop computer. ² Connect the serial port of the USB to serial (RS485) converter to the SICAM FCM terminals with wires. The following table shows the equivalent SICAM FCM terminals and the USB to serial (RS485) converter: Table 1-1 SICAM FCM Terminals and USB to Serial (RS485) Converter SICAM FCM Terminals USB to Serial (RS485) Converter 4 (COM) GND 5 (A/-) R- (D-) 6 (B/+) R+ (D+) [dw_usb-serial-converter, 1, en_us] Figure 1-7 Connecting SICAM FCM via USB to Serial (RS485) Converter to a PC or Laptop Computer 16 SICAM, SICAM FCM Configurator, Configuration and Operation

17 1.5 Control Elements and Control Functions 1.5 Control Elements and Control Functions The following table lists the control elements and control functions. Table 1-2 Control Elements and Control Functions Control Elements Control Functions Home screen Open menu Backup device settings Restore device settings Update firmware Log off Write the settings to the device Read the settings from the device Displays the device-log information with log numbers Pause unpressed Pause pressed SICAM, SICAM FCM Configurator, Configuration and Operation 17

18 1.6 Starting the SICAM FCM Configurator User Interface 1.6 Starting the SICAM FCM Configurator User Interface SICAM FCM Configurator supports the following Web browsers: Microsoft Internet Explorer 8.0 or higher Google Chrome 10.0 or higher Mozilla Firefox 45.0 or higher i NOTE Siemens recommends using Microsoft Internet Explorer 8.0 or higher. Before starting the SICAM FCM Configurator user interface, the following preconditions must be satisfied: Observe the safety requirements when connecting the device. For more information about SICAM FCM device safety requirements, refer to the SICAM FCM Manual. The connection between the SICAM FCM device and PC or laptop computer using USB to serial (RS485) converter is established. The SICAM FCM device is powered on. To start the SICAM FCM Configurator user interface, proceed as follows: ² Double-click the SICAM FCM Configurator icon from the desktop. ² Select the Com port from the list box. [sc_fsi_webconfigconnect_ , 1, en_us] Figure 1-8 Configurator Connection ² Select the Baud rate from the list box. The default baud rate is 9600 bps. ² Select the Parity from the list box. The default parity is None. 18 SICAM, SICAM FCM Configurator, Configuration and Operation

19 1.6 Starting the SICAM FCM Configurator User Interface ² Enter the Unit id from 1 to 247. The default unit id is 1. i NOTE To establish the communication, ensure that the Communication setting parameters (Com port, baud rate, parity) are the same in both SICAM FCM device and SICAM FCM configurator. ² Click Connect. The Log-on to device dialog appears. [sc_fcm_logon_ , 1, en_us] Figure 1-9 SICAM FCM Configurator Log on to device ² Click OK to log on to the SICAM FCM Configurator. The Dashboard page appears. SICAM, SICAM FCM Configurator, Configuration and Operation 19

20 1.7 Dashboard Dashboard SICAM FCM Configurator Dashboard Device Information Group The device information page displays the following: Device health state Boot-loader version number Firmware version number SICAM FCM Configurator (Application software version number) The device information parameters are read-only. [sc_fcm_dashbrd_ , 1, en_us] Figure 1-10 SICAM FCM Configurator Dashboard ² Click the SICAM FCM tile under Device Information. 20 SICAM, SICAM FCM Configurator, Configuration and Operation

21 1.7 Dashboard Engineering Group [sc_fcm_device info, 1, --_--] Figure 1-11 SICAM FCM Configurator Device Information (SICAM FCM) The engineering settings page displays the following parameters in a tree view structure: Communication parameters Device parameters Fault parameters Process parameters DO configuration ² Click the Settings tile under Engineering. SICAM, SICAM FCM Configurator, Configuration and Operation 21

22 1.7 Dashboard [sc_fcm_process parameter, 1, en_us] Figure 1-12 SICAM FCM Configurator Engineering (Settings) Reports and Monitoring Group Reports Group The reports page displays the events and trailing pointers. Events Tile This tile provides information on the events logged in the SICAM FCM device. ² Click the Events tile under Reports. [sc_fcm_events_ , 1, en_us] Figure 1-13 SICAM FCM Configurator Reports (Events) Trailing Pointers Tile This tile provides information on the trailing pointers recorded in the SICAM FCM device. ² Click the Trailing pointers tile under Reports. 22 SICAM, SICAM FCM Configurator, Configuration and Operation

23 1.7 Dashboard [sc_fcm_trailpoint_ , 1, en_us] Figure 1-14 SICAM FCM Configurator Reports (Trailing Pointers) Monitoring Group The monitoring page displays the following parameters: Voltage and current Power Alarm and warnings Energy information Voltage and Current Tile This tile provides information on the real-time current and voltage measurements. ² Click the Voltage and Current tile under Monitoring. [sc_fcm_voltcurr_ , 1, en_us] Figure 1-15 SICAM FCM Configurator Monitoring (Voltage and Current) SICAM, SICAM FCM Configurator, Configuration and Operation 23

24 1.7 Dashboard Power Tile This tile provides information on the real-time power measurements. ² Click the Power tile under Monitoring. [sc_fcm_power_ , 1, en_us] Figure 1-16 SICAM FCM Configurator Monitoring (Power) Alarms and Warnings Tile This tile provides information on the alarms and warnings recorded by the SICAM FCM device. ² Click the Alarms and Warnings tile under Monitoring. [sc_fcm_alarmwarn_ , 1, en_us] Figure 1-17 SICAM FCM Configurator Monitoring (Alarms and Warnings) Energy Tile This tile provides information on the energy measurements. ² Click the Energy tile under Monitoring. 24 SICAM, SICAM FCM Configurator, Configuration and Operation

25 1.7 Dashboard [sc_fcm_energy_ , 1, en_us] Figure 1-18 SICAM FCM Configurator Monitoring (Energy) SICAM, SICAM FCM Configurator, Configuration and Operation 25

26 1.8 Parameter Settings 1.8 Parameter Settings This chapter gives an example of how to set the process parameters with the SICAM FCM Configurator. To set the process parameters, proceed as follows: ² In the SICAM FCM Configurator dashboard, click the Settings tile under Engineering and select Process parameters. ² Select the rated secondary voltage from the Voltage parameters list box. ² Enter the rated primary voltage in the Voltage parameters text box. [sc_fcm_parameter settings, 1, en_us] Figure 1-19 Process Parameters ² Enter the rated primary current in the Current parameters text box. ² Click the Write the settings to the device button. The updated settings are applied to the SICAM FCM device and displayed in the log information. i i NOTE Similarly, you can configure the following parameters: Communication parameters Device parameters Fault parameters DO configuration NOTE For more information about SICAM FCM device parameterization, safety requirements, and SICAM FCM device functions, refer to the SICAM FCM Manual. Information Section The information section provides you more information about the description of parameters and the settings range when you are configuring the parameters. To find more information about the parameter, proceed as follows: 26 SICAM, SICAM FCM Configurator, Configuration and Operation

27 1.8 Parameter Settings ² Click the arrow sign on the yellow bar. The following figure shows an information example for the Modbus ID. [sc_fcm_infordisplay, 1, en_us] Figure 1-20 Information Display with Modbus ID Settings Range SICAM, SICAM FCM Configurator, Configuration and Operation 27

28 1.9 Backup Device Settings 1.9 Backup Device Settings Backup device settings allows you to save the configured device settings data in the PC or laptop computer. Siemens recommends creating a backup of the device settings at regular intervals. The backup can be used to view historical configuration data via the SICAM FCM Configurator and to restore the device settings. To create a backup of the device settings, proceed as follows: ² In the SICAM FCM Configurator dashboard, click the Open menu and select Backup device settings... [sc_fcm_backdevice_ , 1, en_us] Figure 1-21 Backup Device Settings The Backup device settings dialog appears. [sc_fcm_backupconfirm_ , 1, en_us] Figure 1-22 Backup Device Settings Dialog ² Click OK. 28 SICAM, SICAM FCM Configurator, Configuration and Operation

29 1.9 Backup Device Settings The BackupSettings is in progress dialog appears. [sc_fcm_backupsettinginprogress, 1, en_us] Figure 1-23 Backup Device Settings - Download in Progress The File ready for download dialog appears. [sc_fcm_backupconfirm_filereaddy_ , 1, en_us] Figure 1-24 File Ready to Download Dialog ² Click the Start download link to download the backup file. By default, the SICAM FCM device settings backup file is downloaded to C:\ProgramData\Siemens Energy\FCM_Configurator\FCMBackUpSettings. SICAM, SICAM FCM Configurator, Configuration and Operation 29

30 1.10 Restore Device Settings 1.10 Restore Device Settings Restore device settings restores the device settings from the saved backup file. To restore the device settings, proceed as follows: ² In the SICAM FCM dashboard, click the Open menu and select Restore device settings... [sc_fcm_resetdeviceset_ , 1, en_us] Figure 1-25 Restore Device Settings The Restore device settings dialog appears. 30 SICAM, SICAM FCM Configurator, Configuration and Operation

31 1.10 Restore Device Settings [sc_fcm_restoredeviceset_ , 1, en_us] Figure 1-26 Restore Device Settings Dialog ² Click Select a file. ² Select the valid device settings backup (*.xml) file, for example, FCMConfigSettings.xml. SICAM, SICAM FCM Configurator, Configuration and Operation 31

32 1.10 Restore Device Settings [sc_fcm_configfiledial_ , 1, en_us] Figure 1-27 Valid Backup-File Selection ² Click Open. 32 SICAM, SICAM FCM Configurator, Configuration and Operation

33 1.10 Restore Device Settings [sc_fcm_restdevset_ , 1, en_us] Figure 1-28 Restore Device Settings from the Backup File ² Click OK. The device settings are restored from the selected file and Finished successfully. A log-on is required! dialog appears. SICAM, SICAM FCM Configurator, Configuration and Operation 33

34 1.10 Restore Device Settings [sc_fcm_restdevsucc_ , 1, en_us] Figure 1-29 Device Settings Restored Successfully ² Click Close. The Log-on to device dialog appears. [sc_fcm_logon_ , 1, en_us] Figure 1-30 Log-on to Device ² Click OK to log on to the SICAM FCM Configurator again. 34 SICAM, SICAM FCM Configurator, Configuration and Operation

35 1.11 Update Firmware 1.11 Update Firmware You can update the SICAM FCM firmware V03.XX to the SICAM FCM device. Before updating the firmware, download the SICAM FCM firmware (for example, FCM_F3_10_00_00.srec) from the following Siemens Internet page: To update the firmware, proceed as follows: ² In the SICAM FCM dashboard, click the Open menu and select Update firmware... [sc_fcm_updfirmware_ , 1, en_us] Figure 1-31 Update Firmware The Update firmware dialog appears. SICAM, SICAM FCM Configurator, Configuration and Operation 35

36 1.11 Update Firmware [sc_fcm_updatefirm_ , 1, en_us] Figure 1-32 Firmware File Update Dialog ² Click Select a file. The Select File to Upload dialog appears. 36 SICAM, SICAM FCM Configurator, Configuration and Operation

37 1.11 Update Firmware [sc_fcm_select file to upload, 1, --_--] Figure 1-33 Select File to Upload ² Select the valid firmware file, for example, FCM_F3_10_00_00.srec. ² Click Open. SICAM, SICAM FCM Configurator, Configuration and Operation 37

38 1.11 Update Firmware [sc_fcm_update firmware file, 1, --_--] Figure 1-34 Update Firmware File ² Click OK. The Update firmware dialog appears. [sc_fcm_updatefirmprog_ , 1, en_us] Figure 1-35 Firmware Upload in Progress 38 SICAM, SICAM FCM Configurator, Configuration and Operation

39 1.11 Update Firmware i NOTE During the firmware update process, the red LED (fault) blinks until the firmware upload is completed in the SICAM FCM device. ² After successful firmware update, the Finished successfully. A log-on is required! dialog appears. [sc_fcm_updfirmsucc_ , 1, en_us] Figure 1-36 Firmware File Update Successful ² Click Close. After the successful firmware download, the SICAM FCM device resets. i i i NOTE The following compatibility check is applicable to SICAM FCM Configurator V2.10: SICAM FCM Configurator V2.10 allows device firmware updates to V03.XX for devices with firmware V03.XX only. SICAM FCM Configurator V2.10 allows device firmware updates to V02.XX for devices with firmware V02.XX only. SICAM FCM Configurator V2.10 allows updating the parameters into the device with firmware V03.XX only. NOTE SICAM FCM Configurator V1.00 does not support device firmware compatibility check. Refer to section Device Ordering Information" of device manual, order no. E50417-H8940-C580-A1 for checking the device firmware compatibility. NOTE The firmware update is only possible with baud rates ranging from 2400 bps to bps. Siemens recommends using the bps baud rates when updating the firmware. When updating the firmware at lower baud rates, keep the SICAM FCM Configurator window in the active state to avoid the session time out. SICAM, SICAM FCM Configurator, Configuration and Operation 39

40 1.11 Update Firmware i NOTE If the communication between the SICAM FCM device and the SICAM FCM Configurator is disconnected during the firmware update, close the SICAM FCM Configurator window. Log on to the SICAM FCM Configurator to start the firmware update again. 40 SICAM, SICAM FCM Configurator, Configuration and Operation

41 1.12 Log off 1.12 Log off Log off allows to end the user session of the SICAM FCM Configurator. To log off from the SICAM FCM Configurator, proceed as follows: ² In the SICAM FCM Configurator dashboard, click the Open menu and select Log off to disconnect from the SICAM FCM Configurator and return to the logon screen. [sc_fcm_logoff_ , 1, en_us] Figure 1-37 Log off SICAM, SICAM FCM Configurator, Configuration and Operation 41

42 1.13 SICAM FCM Configurator Uninstallation 1.13 SICAM FCM Configurator Uninstallation You can uninstall the SICAM FCM Configurator in one of the following possibilities: Uninstallation via the control panel Uninstallation via the start menu Uninstallation via the Control Panel To uninstall the SICAM FCM Configurator via the control panel, proceed as follows: ² To open the control panel, click Start Control Panel Programs and Features. The Programs and Features window is displayed. [sc_fcm_proguninstall, 1, --_--] Figure 1-38 Programs and Features Window ² Right-click Siemens SICAM FCM Configurator and select the Uninstall/Change option from the context menu. [sc_fcm_setup uninstall, 1, --_--] Figure 1-39 SICAM FCM Configurator Setup Uninstallation ² Click Next >. 42 SICAM, SICAM FCM Configurator, Configuration and Operation

43 1.13 SICAM FCM Configurator Uninstallation ² Select the Remove option to start the uninstallation process. [sc_fcm_remove install, 1, --_--] Figure 1-40 SICAM FCM Configurator Remove Installation ² Click Next >. [sc_fcm_ready to remove, 1, --_--] Figure 1-41 SICAM FCM Configurator Setup Ready to Remove ² Click Remove to start the uninstallation process. The SICAM FCM Configurator program is removed from your computer. This process can take several minutes. ² Click Finish to complete the Siemens SICAM FCM Configurator uninstallation. SICAM, SICAM FCM Configurator, Configuration and Operation 43

44 1.13 SICAM FCM Configurator Uninstallation [sc_fcm_uninstall complete, 1, --_--] Figure 1-42 SICAM FCM Configurator Setup Uninstallation Finished Uninstallation via the Start Menu To uninstall the SICAM FCM Configurator via the start menu, proceed as follows: ² Select Start Menu All Programs Siemens Energy SICAM FCM Configurator Uninstall. [sc_fcm_uninstall_ , 1, en_us] Figure 1-43 SICAM FCM Configurator - Uninstallation from Start Menu 44 SICAM, SICAM FCM Configurator, Configuration and Operation

45 Index A Alarms and warnings 24 Application software version number 20 I Information section 26 Installing SICAM FCM configurator 12 B Backup device settings 17, 28 Backup file 28 Boot-loader version number 20 C Control elements 17 Control functions 17 D Device information 20 E Energy 24 Engineering group 21 Events 22 F Firmware version number 20 H Hardware configuration requirements 11 L Log off 17, 41 M Monitoring 23 P Parameter settings 26 Power 24 R Reports 22 Restore device settings 17, 30 S SICAM FCM configurator dashboard 20 SICAM FCM configurator user interface 18 SICAM FCM terminals 16 T Trailing pointers 22 SICAM, SICAM FCM Configurator, Configuration and Operation 45

46 Index U Uninstallation via the control panel 42 Uninstallation via the start menu 42 Uninstalling SICAM FCM configurator 42 Update firmware 17, 35 USB to serial (RS485) converter 16 V Voltage and current 23 W Web browsers SICAM, SICAM FCM Configurator, Configuration and Operation