H HOLUX Kft. H-1135 Budapest, Béke u Tel: (06 1) Fax: (06 1)

Transcription

1 EBS040SxxxBTE Rev.C 40W Class I/II Programmable IP20 Driver with DALI Features High Efficiency (Up to 89.5%) Full Power at Wide Output Current Range (Constant Power) Thermal Sensing and Protection for LED Module DALI/AC Dim/Timer Dimmable (3 Timer Modes) DimtoOff with Standby Power 0.5 W Alwayson Auxiliary Power: 12Vdc, 200mA (Transient Peak Current up to 400mA) Output Lumen Compensation Long Lifetime Over 90K Hours at 75 C Case Temperature Input Surge Protection: DM 6 kv, CM 10 kv AllAround Protection: OVP, SCP, OTP, IP20 Design and Suitable for Outdoor Applications in Luminaires with IP>54 SELV Output Suitable for Luminaires with Protection Class I and II Complies with Zhaga Interface Specification Book 13 7 Years Warranty Description The EBS040SxxxBTE series is a 40W, constantcurrent, programmable LED driver that operates from Vac input with excellent power factor. Created for many lighting applications including street, tunnel and low bay, it provides a dimtooff mode with low standby power. The high efficiency of these drivers and better thermal design enable them to run cooler, significantly improving reliability and extending product life. To ensure troublefree operation, protection is provided against input surge, output over voltage, short circuit, and over temperature of both the driver and the external LED array. Models Adjustable Output Current Range FullPower Current Range (1) Default Output Current ma ma 700 ma mA ma 1050 ma Input Voltage Range(2) 176~305 Vac 190~250 Vdc 176~305 Vac 190~250 Vdc Output Voltage Range Max. Output Power Typical Efficiency (3) Power Factor (3) Model Number (4) 28~89 Vdc 40 W 89.5% 0.96 EBS040S070BTE 19 ~57Vdc 40 W 89.5% 0.96 EBS040S105BTE Notes: (1) Output current range with constant power at 40W (2) Certified voltage range: Vac or Vdc (except CCC and KS) (3) Measured at full load and 220Vac input (see below General Specifications for details). (4) SELV Output. Representative in Hungary: H HOLUX Kft. H1135 Budapest, Béke u Tel: (06 1) Fax: (06 1) hoso@holux.hu 1 / 13 Tel: Fax: sales@inventronicsco.com

2 EBS040SxxxBTE Rev.C 40W Class I/II Programmable IP20 Driver with DALI 108 EBS040S070BTE IV Operating Area EBS040S105BTE Output Voltage (V) (45,89) (10%Ioset,40/Ioset) (270,89) 60%Load Good Performance Area Allowed Operating Area (450,89) (70,28) (Ioset,28) Output Current (ma) (Ioset,40/Ioset) 100%Load Note: 450mA Ioset 700mA (700,57) (700,34) (700,28) Programmed Operating Area Input Specifications Input Voltage 176 Vac 305 Vac 190~250 Vdc Input Frequency 47 Hz 63 Hz Leakage Current 0.70 ma IEC605981; 240Vac/ 60Hz Input AC Current 0.30 A Measured at full load and 220 Vac input. Inrush Current(I 2 t) 0.35 A 2 s PF 0.90 THD 20% THD 10% At 220Vac input, 25C Cold Start, Duration =368 μs, 10%Ipk10%Ipk. See Inrush Current Waveform for the details. At Vac, 5060Hz, 60%100% Load (2440W) At Vac, 5060Hz, 70%100% Load (2840W) Output Specifications Output Current Tolerance 5%Ioset 5%Ioset At full load condition Output Current Setting(Ioset) Range EBS040S070BTE EBS040S105BTE Output Current Setting Range with Constant Power EBS040S070BTE EBS040S105BTE Total Output Current Ripple (pkpk) Output Current Ripple at < 200 Hz (pkpk) 45 ma 70 ma 450 ma 700 ma 700 ma 1050 ma 700 ma 1050 ma 5%Iomax 10%Iomax At full load condition, 20 MHz BW 2%Iomax At full load condition. Only this component of ripple is associated with visible flicker. 2 / 13 Tel: Fax: sales@inventronicsco.com

3 EBS040SxxxBTE Rev.C 40W Class I/II Programmable IP20 Driver with DALI Output Specifications (Continued) Startup Overshoot Current 10%Iomax At full load condition No Load Output Voltage EBS040S070BTE EBS040S105BTE 119 V 68 V Line Regulation ±0.5% Measured at full load Load Regulation ±1.5% Turnon Delay Time 0.5 s Measured at 220Vac input, 60%100% Load Temperature Coefficient of Ioset 0.04%/C Case temperature = 0C ~Tc max 12V Auxiliary Output Voltage 10.8 V 12 V 13.2 V 12V Auxiliary Output Source Current 12V Auxiliary Output Transient Peak Current 0 ma 200 ma Return terminal is Return 400 ma 400mA peak for a maximum duration of 300ms in a 2s period during which time the a verage should not exceed 200mA. Note: All specifications are typical at 25C unless otherwise stated. General Specifications Efficiency at 220 Vac input: EBS040S070BTE Io= 450 ma Io= 700 ma EBS040S105BTE Io= 700 ma Io= 1050 ma 87.5% 87.0% 87.5% 86.5% 89.5% 89.0% 89.5% 88.5% Measured at full load and steadystate temperature in 25C ambient; (Efficiency will be about 2.0% lower if measured immediately after startup.) Standby Power 0.5 W Measured at 230Vac/50Hz; Dimming off MTBF Lifetime Operating Case Temperature for Safety Tc_s Operating Case Temperature for Warranty Tc_w 340,000 hours 93,000 hours 40 C +90C 40 C +75C 3 / 13 Tel: Fax: sales@inventronicsco.com Measured at 220Vac input, 80% Load and 25C ambient temperature (MILHDBK217F) Measured at 220Vac input, 80%Load and 75C case temperature; See lifetime vs. Tc curve for the details Case temperature for 7 years warranty. Please see Inventronics Warranty Statement for complete details. No condensation Storage Temperature 40 C +85 C Humidity: 5%RH to 85%RH; No condensation. Dimensions Inches (L W H) Millimeters (L W H) 4.85 x 3.12 x x 79 x 33 Net Weight 220 g Note: All specifications are typical at 25C unless otherwise stated.

4 EBS040SxxxBTE Rev.C 40W Class I/II Programmable IP20 Driver with DALI Dimming Specifications DA, DA High Level 9.5 V 16 V 22.5 V DALI DA, DA Low Level 6.5 V 0 V 6.5 V DA, DA Current 0 ma 2 ma Start Input Voltage 180 Vac 250 Vac Default is 220 Vac Start Output Level 30% 100% Default is 100% Stop Input Voltage 160 Vac 230 Vac Default is 170 Vac Stop Output Level 30% 85% Default is 30% AC Dim Gap between Start and Stop Input Voltage 20 Vac Increment of Start and Stop Input Voltage 1 Vac Increment of Start and Stop Output Level 1% Dimming Output Range EBS040S070BTE EBS040S105BTE EBS040S070BTE EBS040S105BTE 10%Ioset Ioset 45 ma 70 ma Ioset 450 ma Ioset 700 ma 700 ma Ioset 1050 ma 45 ma Ioset < 450 ma 70 ma Ioset < 700 ma Note: All specifications are typical at 25 C unless stated otherwise. Safety &EMC Compliance Safety Category Standard ENEC & CE EN , EN KS KS C 7655 Performance Standard ENEC EN EMI Standards EN (1) EN EN EMS Standards EN EN EN EN Notes Conducted emission Test &Radiated emission Test Harmonic current emissions Class C Voltage Fluctuations & Flicker Notes Electrostatic Discharge(ESD): 8 kv air discharge, 4 kv contact discharge RadioFrequency Electromagnetic Field Susceptibility TestRS Electrical Fast Transient/BurstEFT Surge Immunity Test: AC Power Line: Differential Mode 6 kv, Common Mode 8 kv 4 / 13 Tel: Fax: sales@inventronicsco.com

5 EBS040SxxxBTE Rev.C 40W Class I/II Programmable IP20 Driver with DALI Safety &EMC Compliance (Continued) EMS Standards Notes EN EN EN EN DALI Standards Conducted Radio Frequency Disturbances TestCS Power Frequency Magnetic Field Test Voltage Dips Surge Immunity Test: AC Power Line: Differential Mode 6 kv, Common Mode 10 kv Electromagnetic Immunity Requirements Applies to Lighting Equipment Notes DALI IEC ,102 & part of 207 (2) Notes: (1) This LED driver meets the EMI specifications above, but EMI performance of a luminaire that contains it depends also on the other devices connected to the driver and on the fixture itself. (2) Optional Commands Implemented: 242 (query short circuit), 243 (query open circuit). Lifetime vs. Case Temperature Inrush Current Waveform 5 / 13 Tel: Fax: sales@inventronicsco.com

6 EBS040SxxxBTE Rev.C 40W Class I/II Programmable IP20 Driver with DALI Efficiency vs. Load EBS040S070BTE(Io=450mA) EBS040S070BTE(Io=700mA) EBS040S105BTE(Io=700mA) EBS040S105BTE(Io=1050mA) Power Factor 6 / 13 Tel: Fax: sales@inventronicsco.com

7 EBS040SxxxBTE Rev.C 40W Class I/II Programmable IP20 Driver with DALI Total Harmonic Distortion Protection Functions External Thermal Protection NTC Protection Current Floor R kohm R kohm When R_NTC falls below R1, External Thermal Protection is triggered, reducing output current until R2 is reached. When R_NTC is less than R2, output current is reduced to the programmed Protection Current Floor. 10%Ioset 60%Ioset 100%Ioset 10%Ioset>Iomin (default setting is 60%) Iomin 60%Ioset 100%Ioset 10%Ioset Iomin (default setting is 60%) Over Temperature Protection Short Circuit Protection Over Voltage Protection Decreases output current, returning to normal after over temperature is removed. Auto Recovery. No damage will occur when any output is short circuited. The output shall return to normal when the fault condition is removed. Limits output voltage at no load and in case the normal voltage limit fails. Dimming DALI Dimming The recommended implementation of the dimming control is provided below. 7 / 13 Tel: Fax: sales@inventronicsco.com

8 EBS040SxxxBTE Rev.C 40W Class I/II Programmable IP20 Driver with DALI Implementation: DALI Dimming Time Dimming Time dimming control includes 3 kinds of modes, they are Self AdaptingMidnight, Self Adapting Percentage and Traditional Timer. Self AdaptingMidnight: Automatically adjusts the dimming curve based on the ontime of past two days (if difference <15 minutes), assuming that the center point of the dimming curve is midnight local time. Self AdaptingPercentage: Automatically adjusts the ontime of each step by a constant percentage = (actual ontime for the past 2 days if difference <15 min) / (programmed ontime from the dimming curve). Traditional Timer: Follows the programmed timing curve after power on with no changes. AC Dimming The default range of AC Dim is Vac. The range can be adjusted via the programming interface. Also, the Start Input Voltage, Start Output Level, Stop Input Voltage and Stop Output Level can be set. There needs to be a minimum of 20V difference between Start and Stop Input Voltage settings when programming the driver. There must be a minimum voltage difference of 5V from the Start Input Voltage before the driver starts dimming. 8 / 13 Tel: Fax: sales@inventronicsco.com

9 uuto2l((((ebn((aa+(oeq((uigrpu(greatekge))))nar)l))))ebs040sxxxbte Rev.C 40W Class I/II Programmable IP20 Driver with DALI Notes: 1. In the green area, the driver will operate normally. 2. In the yellow area, the driver will operate safely but not fulfill requirements. Output Lumen Compensation Output Lumen Compensation (OLC) may be used to maintain constant light output over the life of the LEDs by driving them at a reduced current when new, then gradually increasing the drive current over time to counteract LED lumen degradation. Wire Connection Diagram L, N, EQUI Wire Crosssection 0.4 mm mm 2 Pushin at 45ºangle, solid and 20 AWG 16 AWG stranded wire Strip Length 8.5 mm 9.5 mm Vout+, Vout, Return, Tmon, +12V, DA, DA Wire Crosssection 0.2 mm mm 2 Pushin at 45ºangle, solid and 22 AWG 16 AWG stranded wire Strip Length 8.5 mm 9.5 mm LED Load Load(Max.200mA) QUINTCEDALI NVoVoReTm1DDAA)~ t+turnvbwlhicrluwblryptkedehicneac Input 9 / 13 Tel: Fax: sales@inventronicsco.com

10 EBS040SxxxBTE Rev.C 40W Class I/II Programmable IP20 Driver with DALI Programming Connection Diagram Note: The driver does not need to be powered on during the programming process. Please refer to PRGMUL2 (Programmer) and PRGFIXE (Programming Fixture) datasheet for details. 10 / 13 Tel: Fax: sales@inventronicsco.com

11 11 / 13 EBS040SxxxBTE Rev.C 40W Class I/II Programmable IP20 Driver with DALI Tel: Fax: sales@inventronicsco.com Mechanical Outline EBS040SxxxBTE PROJ: Unspecified tolerance:±1n(white)l(black)vout+(red)vout(blue)return(white)tmon(black)+12v(orange)equi(green)tcda(gray)da(purple)optional Cable Clamp ENDCAP01 Unspecified tolerance:±1 PROJ:

12 EBS040SxxxBTE Rev.C 40W Class I/II Programmable IP20 Driver with DALI Note: The cable clamp is to be installed with EBS040SxxxBTE drivers for independent application. Please refer to ENDCAP01 datasheet for details. RoHS Compliance Our products comply with the European Directive 2011/65/EC, calling for the elimination of lead and other hazardous substances from electronic products. 12 / 13 Tel: Fax: sales@inventronicsco.com

13 EBS040SxxxBTE Rev.C 40W Class I/II Programmable IP20 Driver with DALI Revision History Change Date Rev. Description of Change Item From To A Datasheets Release / / Features 7 Years Warranty Added Features Alwayson Auxiliary Power Added Input Specifications PF/THD Updated B Output Specifications Temperature Coefficient of Ioset Updated Output Specifications General Specifications 12V Auxiliary Output Transient Peak Current Operating Case Temperature for Warranty Tc_w Added Updated Description / Updated C Operating Case Temperature for Warranty Tc_w Notes Updated Wire Connection Diagram / Updated 13 / 13 Tel: Fax: sales@inventronicsco.com