Spring loaded connectors ( 2 pairs ) for AWG wire 300 ma base current, jumper options for 380, Spring loaded connectors ( 2 pairs )

Transcription

1 ATX LED Consultants Inc 815-A Brazos #326 Austin TX, AL-WS-DR2 Decorator style Dual Constant Current LED Dimmer / Driver with integrated switch 56 watt 3-Way DALI Product Description - AL-WS-DR2 wall switch This switch operates just like any standard residential light switch however it takes 24-50v DC instead of 120VAC, and directly drives up to 20 LEDs. This Decorator style switch in a standard residential style outline fits into any home, looks like any switch yet requires no licensed electrician for installation. No complicated controller is required. For 3-way operation a simple 2 wire link with AWG24 or better allows 2, 3, or an unlimited numbers of switches to control one set of LED s. Any single pole switch found at Home Depot can be used to add a 3-Way remote switch, or dual pole switch for an unlimited number of switch points. Stand alone it operates as a simple switch for 2 strings of LED s. Jumper selections for 300, 400, 600 or 700 ma LEDs with up to 28 watts per channel two channels are provided for 56 watts total. For example, 16 3 Watt LEDs can connected in series and parallel to this switch / dimmer device. Use AWG 16 or 18 to bring 48v ( or 24 to 50 volts ) from a central power supply over to the switches, then use AWG 18 to connect to your LEDs no tools are required to wire this device. A proven rocker switch and brightness slider leverages mass production of Decorator switches, now for low voltage applications any casual user requires no training, no App to use this switch. Perfect, flicker free dimming from off to 5 to 100%. No network setup is required. Temperature feedback assures excellent dimming. To enable Home / Business automation the AL-WS-DR2 includes a DALI opto isolated serial bidirectional port for remote and voice control. Use the AL-WIZ to connect to Alexa or Google home voice control. The DALI protocol is supported, with automatic addressing. Use low cost CAT-3 wire up to 1000 ft to implement remote management. Power and DALI are duplicated allowing easy installation. Specifications Power source and load Spring loaded connectors ( 2 pairs ) for AWG wire 300 ma base current, jumper options for 380, LED constant current output 600 or 680 ma per channel Spring loaded connectors ( 2 pairs ) Input voltage range 24v to 50 volts ( power for LEDs) Standby power consumption 50 milliwatts Conversion efficiency Over 95% Protection Reverse protection and static protection Operating Temperature 0 C ~ 50 C Size 115 x 46 x 50 mm Dimming 2 to 100 %,, Current control with temperature tracking FCC and interference All outputs are RF filtered for minimal interference Maximum output voltage Input minus 4 volts Minimum output voltage 6 volts, minimum current self calibrating* Hot Swap Yes - can unplug and connect LEDs with power applied. DALI interface Individual, group and scene support Opto Coupled AWG gauge wire spring fit short and long addresses 16 to 24 volts 2 ma

2 Wiring the AL-WS-DR2 See for more examples

3 Powering the AL-WS-DR2 Power the switch via the Power input connectors, 48 or 50v is recommended. No DALI connection is required. You can feed from the input to the output up to 2 amps. After power up once set to minimum Dim at that time you might see a flicker while it learns the capability of the attached LED. After that phase the result is stored in on-board EEprom and will be updated for temperature and aging changes or each time the power to the switch is cycled. Default Operation By default the AL-WS-DR2 operates stand alone no controller or master is required. Connect the dual LED outputs to your LED s. Combinations of 300 ma to 700 ma LED can be used. Our AL-LED-Doubler allows the number of LEDs to be doubled. See for wiring suggestions. 3-Way Operation Simply connect an AWG24 ( solid CAT-3 is recommended) between the N-WAY pins and a remote standard Decorator style wall switch. If more control switches are needed use a dual pole switch in an XOR setup. No controller is required; an unlimited number of switches can control one light. 3-Way works in default or DALI modes Default DALI Operation Simple remote control the device accepts DALI broadcast commands so any DALI switch or master that sends broadcast commands can connect to this device remotely for on/off/dimming the LED outputs are controlled by the switch or DALI broadcast packets. In Default mode no DALI transmissions occur. DALI packets override the local switch setting. Full DALI Operation For full DALI operation - connect your powered DALI bus to the DA+ and DA- pins (polarity is not significant ) of the AL-WS-DR2. The device responds to the provisioning commands from a DALI master. In order for addressable functions to work, a short address [ 0 thru 63] needs to be assigned. This can be done by a DALI Master with configuration features. Once a short address is assigned the device can be understood to operate as two devices in one. 1) DALI driver the LED outputs will have a unique DALI short address after provisioning. This address is automatically assigned to a group with the short addresses included in one group. The LED outputs are connected to LED s and they can now be controlled by DALI commands from the bus. All DALI commands are supported. The actual address and group is defined and can be changed by the DALI master. 2) DALI Dimmer / Switch after provisioning the Switch in this device is placed into Group mode flipping the switch, or the 3-way remote switches, or the dimming value will cause a DALI Group command to be sent internally to the driver 0-10v output as well as externally to the DALI bus. Since the internal LED drivers are automatically loaded into the assigned group for the switch the device works as expected. You can change this behavior using a DALI-100 master controller. 3) A DALI Reset command will return both functions to default (broadcast) operation. Use a DALI-100 or similar provisioning tool to assign any other Dali drivers to the switch Group address. The default Group assigned to the switch is the same as the short address assigned to the on-board 0-10v drive. Since Groups are between 0-15, Short Addresses above 15 are truncated to 4 bits.

4 Recommended ETL listed LED s Table 1 direct to LED method LED rated watts Model Size inches LED rated ma Max Count Total power needed Wiring method 3 B01A6HJJLRY ma 8 26 watts Series 6 P023R ma 4 26 watts Series 12 P023R ma 2 25 watts Direct 6 P023R ma 8 50 watts Series 12 P023R ma 4 46 watts Series 11 PR ma * 8 51 watts Series 14 PR ma * 4 51 watts Series * when 1000 ma LED s are used the max current delivered is 700 ma so the power is derated by 40% Table 2 using the AL-LED-Doubler current Mirror to allow more LED s LED rated watts Model Size Inches LED rated ma Max Count Total power needed Wiring method 1 B01FVRQVK ma watts 4 in series, 4 chains 3 B01A6HJJLRY ma watts 4 in series, 4 chains 6 P023R ma 8 54 watts 2 in series, 4 chains 12 P023R ma 4 50 watts Direct

5 The AL-LED-Doubler device accepts a 0 to 700 ma input, and outputs two ma lines. The two lines are matched in current assuring long life of the LED s regardless of temperature differences, different line lengths, or different manufacturers. Dimming is perfect down to low current levels. In the case of a mismatched LED type, wiring or LED fault, the AL-Doubler indicates the problem and helps identify the cause. See AL-LED-Doubler DALI bus products from ATX LED Consultants Structured Wiring DALI power supply with easy wiring Wall Switch v Driver with DALI AL-DALI-010v Alexa to DALI interface AL-DALI-WIZ Typical Compatible standard DALI products 120 VAC DALI LED driver DALI Wall Switch DC-DC Dali driver expansion option

6 DALI Commands Supported Broadcast / Individual / Group commands 0 LED Off 1 UP 8 steps 2 Down 8 steps 3 UP one step but don't turn on 4 Down one step but not off 5 Set to MAX level 6 Set to Min level 7 Down one step and Off if needed 8 Up one step or on if needed 32 Reset to defaults ( don't change Short Address) 33 Save ARC level to DTR A 35 Set N-Way mode ( DTR is the value ) See table below 42 Store DTR as new Max Level, 43 Store DTR as new Min Level 45 Store DTR as new power up level 46 Store DTR as Fade Up duration 47 Store DTR as Fade Down duration FADE times in seconds ( 0-15 ) 0, 7, 10, 14, 20, 28, 40, 56, 80, 113, 160, 226, 320, 452, 640, Store DTR as short address * 129 Enable memory Bank write 144 Query Status bit 0 Left Led Fail ( DR2 ) bit 1 Right LED Fail ( DR2 ) bit 2 ARC Level greater than 0 bit 3 N/A bit 4 Fade in action bit 5 Device not configured after reset bit 6 Missing Short Address bit 7 No ARC level set after power failure 145 Query if Short Address matches one stored 146 Query if either attached LED fail 147 Query if LED on 149 Query if in Reset state 150 Query if no address assigned 151 Query DALI version number ( == 1) 152 Query DTR 153 Query LED type ( == 6) 154 Query Physical DIM level ( See DR2 info) 155 Query Power Failure 156 Query DTR Query DTR 2 A 158 Query N-Way mode 160 Query Actual Dim Level 161 Query Max Level 162 Query Min Level

7 DALI Commands Supported 163 Query Power On Dim Level 164 Query System Fail Level 165 Query Fade Rate value A 166 Query HW Type ( 2 = 0-10v, 1 = DR2) 192 Query group association Query group association Query Random High bits 195 Query Random Middle bits 196 Query Random Low bits 197 Query Memory Bank address DTR1:DTR C 231 Set DTR as CCT ratio C 232 Set CCT Cooler C 233 Set CCT Warmer C 243 Save Color C 250 Query Color A 252 Query N-Way Mode 255 extended DALI version ( 209 ) Global Commands processed by all DALI devices on the bus 256 Terminate 257 Set DTR * 258 Initial Addressing Mode 259 Randomize 260 Compare Random Address 261 Withdraw from Random Addressing 264 Set High Byte 265 Set Middle Byte 266 Set Low Byte 267 Set Short Address if match 268 Query Short Address 269 Query Long Address Match 272 If 8, enable CCT mode 273 Set DTR1 274 Set DTR2 275 Write Data at Memory Bank DTR1:DTR Send confirm 276 Write Data at Memory Bank DTR1:DTR no response N-Way Modes sent with command 35 0 THREE_WAY ( Default ) 1 PUSHBUTTON ( N-Way push on, push off ) DUAL_SWITCH ( two outputs share the DIM level, 2 with individual switch controls) 3 PIR mode A ( 2 nd output it always ON, but dimmable ) 4 PIR mode B ( 2 nd output is always ON, full power)

8 Memory Bank 0 Address Bank 0 Name Bank 0 Value 0 Bytes per Bank ( minus 1) 1 Checksum calculated 2 Number of Banks ( minus 1) 3 UPC code msb 4 UPC code 5 UPC code 6 UPC code 7 UPC code 8 UPC code 9 Serial Number Assigned by Master msb 10 Serial Number 11 Serial Number 12 Serial Number 13 FW Version 14 HW Version 15 N-Way Mode Storage User Defined 63 3 Memory Bank 1-3 Address Name Value 0 Bytes per Bank ( minus 1) 1 Checksum calculated 2 Number of Banks ( minus 1) 3-63 User Storage 63 3

9 Memory Bank 4 Address Name Value 3 Up Time Hours / Up Time Hours (8 years max) 5 On Time Hours / On Time Hours (8 years max) 7 Power Used Dim level * Hours 8 Power Used (Dim level * Hours) /256 9 Slider Min Level Slider Max Level 2-254