VIDEOKIT VK8K/6256 SERIES 6 Wire bus one way, two way videokit VK8K VK8KC. Installation handbook. English

Transcription

1 English VIDEOKIT VK8K/656 SERIES 6 Wire bus one way, two way videokit VK8K VK8KC 656 Installation handbook EN V 3.4 3/08/6 We recommend This equipment is installed by a Competent Electrician, Security or Communications Engineer.

2 VK8K/656 Series 6 wire Bus videokit Index Introduction... System components and available versions... 3 General directions for installation... 5 Troubleshooting guide... 6 Art Speaker unit... 7 Art Art Digital codelock module Series Surface and flush mounting door station installation... Art " colour videophone Series Videophone wall mounting instructions... 7 Installation diagrams... 8 Introduction The VK8K Series is a new range of videokits that use the 8000 Series external door station and the Art. 656 videophone which is specific for this range of videokit and VK4K videokit. The camera/audio unit is the size of a one point five 8000 Series module and is available in either flush (VK8K) or surface (VK8K-S) mounting versions. As a result of using microprocessor technology in the door panel and videophone, a number of additional features have been added to enhance the operation of the videokits and give greater feedback to the visitor and user. Disability friendly, acoustic signals from the door panel to inform the visitor of call status (call made, ringing, speak, door open). Two methods of operating the electric lock:- ) Dry contact relay, ) capacitor discharge circuit. Connections for a push to exit button. Programmable door open and conversation time. Expandable to 4 entrance panels (requires an additional relay Art. 506N for each entrance panel). Facility for the connection of a codelock Art Programmable number of call tone rings from to a maximum of 8. Input for local door bell push button. Door open status LED (additional wire required from the door to the videophone). Programmable timed privacy function from 5 minutes to a maximum of 8 hours. Videophones can have a maximum of two additional audio telephone handsets connected in parallel. Up to 4 videophones can be connected in parallel, all with intercommunication facility. Camera recall on all systems, with selective recall on systems with multiple entrances. Door panel camera can be adjusted horizontally and vertically (0 degrees). VK8K/656 Series - Installation handbook EN - V 3.4-3/08/6

3 VK8K/656 Series 6 wire Bus videokit System components and available versions VK8K/656 Colour videokit. OUTDOOR STATI INDOOR STATI Videophone Art. 656 pag. 4 Camera unit Art pag ACCESSORIES Power supply Art. 850K pag Flush Mounting Surface Mounting Fig. - VK8K/656 components (measures in mm) E WAY VERSIS VK8K-/656 - flush mounting Outdoor station composed of: Art /DN/C: button camera unit Art. 8855: Flush mounting box Art. 8875: Rainshield VK8K-S/656 - surface mounting Outdoor station composed of: Art /DN/C: button camera unit Art. 8885: Surface mounting box Colour videophone Art. 656 Colour videophone Art. 656 Power supply Art. 850K Power supply Art. 850K TWO WAY VERSIS VK8K-/656 - flush mounting Outdoor station composed of: Art /DN/C: buttons camera unit Art. 8855: Flush mounting box Art. 8875: Rainshield VK8K-S/656 - surface mounting Outdoor station composed of: Art /DN/C: buttons camera unit Art. 8885: Surface mounting box Colour videophones Art. 656 Colour videophones Art. 656 Power supplies Art. 850K Power supplies Art. 850K VK8K/656 Series - Installation handbook EN - V 3.4-3/08/6

4 VK8K/656 Series 6 wire Bus videokit System components and available versions VK8KC/656 Colour videokit plus a codelock module. OUTDOOR STATI INDOOR STATI Videophone Art. 656 pag. 4 Camera unit Art pag. 7 Codelock module Art pag ACCESSORIES Power supply Art. 850K pag. 5 Fig. - VK8KC/656 components (measures in mm) Flush Mounting Surface Mounting E WAY VERSIS VK8KC-/656 - flush mounting Outdoor station composed of: Art /DN/C: button camera unit Art. 8800: Codelock module Art. 8857: Flush mounting box Art. 8877: Rainshield VK8KC-S/656 - surface mounting Outdoor station composed of: Art /DN/C: button camera unit Art. 8800: Codelock module Art. 8887: Surface mounting box Colour videophone Art. 656 Colour videophone Art. 656 Power supply Art. 850K Power supply Art. 850K TWO WAY VERSIS VK8KC-/656 - flush mounting Outdoor station composed of: Art /DN/C: buttons camera unit Art. 8800: Codelock module Art. 8857: Flush mounting box Art. 8877: Rainshield VK8KC-S/656 - surface mounting Outdoor station composed of: Art /DN/C: buttons camera unit Art. 8800: Codelock module Art. 8887: Surface mounting box Colour videophones Art. 656 Colour videophones Art. 656 Power supplies Art. 850K Power supplies Art. 850K VK8K/656 Series - Installation handbook EN - V 3.4-3/08/6

5 VK8K/656 Series 6 wire Bus videokit General directions for installation CNECTI TO MAINS The system must be installed according to national rules in force, in particular we recommend to: Connect the system to the mains through an all-pole circuit breaker which shall have contact separation of at least 3mm in each pole and shall disconnect all poles simultaneously; The all-pole circuit breaker shall be placed for easy access and the switch shall remain readily operable. POWER SUPPLY INSTALLATI Remove the terminal side covers by unscrewing the retaining screws; Fix the power supply to a DIN bar or directly to the wall using two expansion type screws; Switch off the mains using the circuit breaker mentioned above and then make the connections as shown on the installation diagrams; Check the connections and secure the wires into the terminals; Replace the terminal covers and fix them using the relevant screws; When all connections are made, restore the mains. CABLE SIZE Video connections and Audio connections must be wired in twisted pair: pair the video lines (terminals/signals V and V ), pair the audio lines (terminals /signals and ). Power supply Distance Up to 40mt wires Ø mm 0mt max Suggested cables type CAT5/CAT6 FTP/UTP AWG4 Videophone BROWN WHITE/BROWN BLUE WHITE/BLUE ORANGE WHITE/ORANGE GREEN WHITE/GREEN Up to 40mt * * V V * Couple the two wires to double the section. Outdoor station Power supply Distance Up to 50mt From 50 to 00mt From 00 to 00mt wires Ø mm 0mt max Suggested cables type Belden 9746 or equivalnet 4 pair (8 cores) 0.35mm AWG - 48Ω/Km Belden 9690 or equivalnet 3 pair (6 cores) 0.8mm AWG8-9.Ω/Km Belden 957 or equivalnet 4 pair (8 cores) 0.8mm AWG8-9.Ω/Km Videophone "" and " " Ø 0.35mm "" and "" Ø 0.35mm Twisted pair "V" and "V" Ø 0.35mm Twisted pair Up to 50mt "" and " " Ø 0.75mm "" and "" Ø 0.5mm Twisted pair "V" and "V" Ø 0.5mm Twisted pair from 50 to 00mt "" and " " Ø.5mm "" and "" Ø 0.75mm Twisted pair "V" and "V" Ø 0.75mm Twisted pair from 00 to 00mt V V Outdoor station V V Outdoor station V V Outdoor station VK8K/656 Series - Installation handbook EN - V 3.4-3/08/6

6 VK8K/656 Series 6 wire Bus videokit Troubleshooting guide In case of system failure, try the following preliminary checks: Check that the cables are connected as shown in the installation diagram and that the cables are firmly fixed into the relevant terminals; Check that the mains voltage is available on terminals 30Vac (or 7Vac) and 0 of the power transformer Art. 850K; Check the 4Vac voltage output of the power transformer Art. 850K. If this voltage is not available it could be the,6a fuse, in this case remove the mains voltage, remove possible short-circuits or overload sources then replace the fuse with an equal or equivalent one. Check that the voltage between the terminals + and - of the speaker unit is between 6 and 0Vdc. If the problem persists try the tests in the following table or contact technical support. SYMPTOM CAUSE SOLUTI The door station is not able to call the extension (the bell LED is switched on for seconds): Wrong connection between door station and the videophone Cable size too small. Programmed videophone address incorrect. You have changed the videophone address without power down the system. External call works but when answered Cable size too small. the communication fails: During the conversation it is not possible Cable size too small. to open the door: During the conversation it is not possible to open the door but the key LED on the door station switches on for the programmed time: Incorrect position of J jumper. Electric lock wires unconnected or in short. Wrong electric lock type. Check the 6 common wire connections especially wire (speech line/data). Increase cable size or double up using two wires for each connection. Check videophone address on dip-switches. Power down the system then power up again to detect the new videophone address. Increase cable size or double up using two wires for each signal. Increase cable size or double up using two wires for each signal. Check J position on the door station. Check connection. Check that the electric lock type (ac or dc) is suitable for the J position chosen. Speech only from outside to inside: Wire broken or in short. Check connection of wire. Low volume of speech: Volume trimmers of door station require Adjust the trimmers until the required adjustment. volume is reached. Noise over the speech line during the conversation: Camera recall service does not work: Intercommunicating call does not work: The video shown on the monitor is of a bad quality and the image is distorted or double Local call does not work: The 6 common wires are cabled together with 30 or 380Vac power lines. The 6 common wires are cabled together with 4Vac videophone power supply wires. Camera recall button pressed for a number of times different from the ID of the door station to be switched on. Key button pressed for a number of times different from the videophone address value. V,V signals unconnected, reversed or shorted. The switches of the two way dip-switch are not both in position. V,V of the last Art. 36N (if present) not closed with 75 Ohm resistor. Separate the 6 common wires from the high voltages cables. Separate the 6 common wires from the two 4Vac wires or cable them together only for a short distance. Check the ID (..4) of the door station to be recalled and press the camera recall button as many time as the ID value. Check the address of the videophone you are calling and try again. Check that the wires are not broken or shorted. Set both switches to the position. Use x 75 Ohm resistors to connect V & V to 0V. Wrong connection or call button broken. Check connection or replace the button. VK8K/656 Series - Installation handbook EN - V 3.4-3/08/6

7 VK8K/656 Series 6 wire Bus videokit Art Speaker unit When installing you see the back side of the door panel Colour B&W Aluminium Stainless steel Fig. Fig. CTROLS (SPEAKER & MICROPHE VOLUME) Trimmer to adjust the speaker volume. Rotate clockwise to increase or anti- clockwise to decrease. Trimmer to adjust the microphone volume. Rotate clockwise to increase or anticlockwise to decrease. SETTINGS (DIP-SWITCH & JUMPERS) 4 WAY DIP-SWITCH First two switches are used to set the speaker unit address: the speaker unit address is required for camera recall operation on or more entrance systems. SW Switches, Unit Address OFF OFF OFF OFF 3 4 SW Switch 3 Conversation Time OFF 60 seconds 0 seconds SW Switch 4 Door opening time (J = L position) OFF seconds 6 seconds VK8K/656 Series - Installation handbook EN - V 3.4-3/08/6

8 VK8K/656 Series 6 wire Bus videokit Art Speaker unit JUMPERS J, J, J3 J= J= J= J= J3= Reassurance tone volume = High Reassurance tone volume = Low Door open relay operating mode = Capacitor discharge Door open relay operating mode = Dry Contacts Only for Art , call buttons operating mode = each button calls a different videophone Only for Art , call buttons operating mode = both buttons call the same videophone J3= When the door open relay operating mode is set to capacitor discharge *, one terminal of the electric lock must be connected to ground while the second must be connected to NO terminal. The NO terminal will supply a temporary voltage when the speaker unit receives the door open command. * When capacitor discharge operating mode is set, one terminal of the electric lock must be connected to the ground while the second one must be connected to NO terminal. The NO terminal will supply a temporary voltage when the speaker unit receives the door open command (we suggest to use a Vac/dc A max electric lock). Setting dry contacts operating mode, when the speaker unit receives the door open command, the NO terminal will be internally linked to the C terminal for the programmed time (switch 4 of the 4 way dip-switch bank). SIGNALS (TERMINALS) NO Door open relay normally open contact NC Door open relay normally closed contact Max 4Vdc, 3mA when used as dry contacts relay C Door open relay common contact PTE Active low input to control directly the door open relay SL Active low output to enable the enslavement relay for video signal exchange (active with a call in progress) BS Input/Output busy signal (about V in stand-by, about 0V with a call in progress) V Balanced video signal sync.+ V Balanced video signal sync. Speech line output from the microphone (about V in stand-by, about 3V with a conversation in progress) Speech line input toward the loudspeaker and data signal (about V in stand-by, about 5V with a conversation in progress) Vout Vdc. 0, max. output to supply accessiories Power input ground Power input 6 0Vdc TECHNICAL SPECIFICATI Power Supply: 0Vdc Power consumption: Stand-by: 70mA Operating: 50mA Working Temperature: C VK8K/656 Series - Installation handbook EN - V 3.4-3/08/6

9 VK8K/656 Series 6 wire Bus videokit Art Art Digital codelock module DESCRIPTI Access control system with codes and Relay outputs for Art (3 codes and 3 Relay outputs for Art ). Engineer s code to enter into the Programming Menu ( from 4 to 8 digits). Programming of the activation time of each relay from up to 99 seconds or latching. Possibility to activate relay by shorting terminal SW to GND and relay by shorting terminal SW to GND. Both relays will operate for the programmed time. Keypad gives an acoustic (buzzer) signal during the entering of codes and a continuous melody for 4 or more seconds, according to the number of mistakes (self protection). Keypad includes panel illumination and LED s to show the following:»» Correct relay code (green LED on for seconds).»» Red LED to indicate when in the programming menu. MODELS Art. 8800: Module Relay with keypad illumination LEDs Art : Module 3 Relay with keypad illumination LEDs Fig. OPERATI To use the system, type in the programmed code and press ENTER, the green LED will illuminate and the relay will operate for the programmed time.to cancel remain open time, type in the same code and press CLEAR. If a wrong code is entered, a continuous melody will sound for 4 or more seconds, according to the number of mistakes. INITIALIZATI When the installation is concluded and carried out according to the wiring diagram, power up the system and program it by following the VX8800 PROGRAMMING Flow Chart. PROGRAMMING Refer also to flow chart. Enter ENGINEER S CODE : first time type six times ( factory preset) and press ENTER (The red LED will illuminate). Confirm ENGINEER S CODE (typing again the same) or type the new code (4 to 8 digits) then press ENTER (Melody). Pressing twice the ENTER button without changing the ENGI- NEER S CODE, will exit from the programming. Enter the code (4 to 8 digits) to enable RELAY (ACCESS ) or re-enter the existing code then press ENTER (Melody). Enter the RELAY operation time ( digits 0 to 99 I.E. 05=5 seconds, 00= remain open time) or re-enter the existing time then press ENTER (Melody). Enter the code (4 to 8 digits) to enable RELAY (ACCESS ) or re-enter theexisting code then press ENTER (Melody). Enter the RELAY operation time ( digits 0 to 99 I.E. 05=5 seconds, 00=remain open time) or re-enter the existing time then press ENTER (Melody). Enter the code (4 to 8 digits) to enable RELAY 3 (ACCESS 3 only for Art ) or re-enter the existing code then press ENTER (Melody). Enter the RELAY 3 (only for Art ) operation time ( digits 0 to 99 I.E. 05=5 seconds, 00=remain open time) or re-enter the existing time then press ENTER (Melody). The system is ready to use (the red LED will be off). Press Enter (Red LED will be ) Press Enter (melody) Press Enter (melody) Press Enter (melody) Press Enter (melody) Press Enter (melody) Press Enter (melody) Press Enter (melody) *** Only for Art ENTER THE "ENGINEER S CODE" CFIRM OR CHANGE "ENGINEER S CODE" ENTER "ACCESS CODE" ENTER "ACCESS TIME" ENTER "ACCESS CODE" ENTER "ACCESS TIME" ENTER "ACCESS 3 CODE"*** ENTER "ACCESS 3 TIME"*** SYSTEM READY TO USE First time six times factory preset Type again six times or the new engineer s code 4 to 8 digits Code to enable relay 4 to 8 digits Two digits (0 to 99) i.e. 05=5 Seconds 00= remain open Code to enable relay 4 to 8 digits Two digits (0 to 99) i.e. 05=5 Seconds Code to enable relay 3 4 to 8 digits Two digits (0 to 99) i.e. 05=5 Seconds Red led will be off VK8K/656 Series - Installation handbook EN - V 3.4-3/08/6

10 VK8K/656 Series 6 wire Bus videokit Art Art Digital codelock module INSTRUCTI TO RETURN SYSTEM TO PRESET ENGINEER S FACTORY CODE Turn off power to code lock. Keep ENTER button pressed while turning back on the power to the code lock. Release ENTER button. The master code is now set at factory engineer s code (six times ). Proceed with programming for a new system. NOTES To switch off any relay while operating, type in the relevant code then press the CLEAR button. To operate relays together, set the same code for each relay. If a wrong code is entered, the system will lock out for 5 seconds which will increase each time a wrong code is entered. The system will operate only when the correct code is entered. GENERAL DIRECTIS FOR INSTALLATI In order to achieve the best results from the schematics described it is necessary to install only original VIDEX equipment, strictly keeping to the items indicated on each schematic and follow these General Directions for Installation: The system must be installed according to national rules in force, in any case the running of cables of any intercom unit must be carried out separately from the mains; All multipair cables should be compliant to CW308 specification (0.5mm twisted pair telephone cable.»» Cables for speech line and service should have a max resistance of 0Ω»» Lock release wires should be doubled up (Lock release wires and power supply wires should have a max resistance of 3Ω); The cable sizes above can be used for distances up to 50m. On distances above 50m the cable sizes should be increased to keep the overall resistance of the cable below the RESISTANCES indicated above; Double check the connections before power up; Power up the system then check all functions. LOCK RELEASE BACK EMF PROTECTI A varistor must be fitted across the terminals on AC lock release (Fig.A) and a diode must be fitted across the terminals on a DC lock release (Fig.B) to suppress back EMF voltages. Connect the components to the lock releases as shown in figures. VARISTOR (MOV) DIODE N400 V AC LOCK RELEASE V DC LOCK RELEASE Fig. A Fig. B VK8K/656 Series - Installation handbook EN - V 3.4-3/08/6

11 VK8K/656 Series 6 wire Bus videokit Art Art Digital codelock module RE-PROGRMMING GUIDE Press Enter (Red light will illuminate*) Press Enter Press Enter Press Enter YES Repeat steps for relay and relay 3*** ENTER THE ENGINEER S CODE RE-ENTER THE ENGINEER S CODE ENTER ACCESS CODE ENTER ACCESS TIME MORE DOORS? NO PRESS ENTER TWICE TO EXIT PROGRAMMING Alternatively enter a new engineer s code (4 to 8 digits) Relay code (4-8 digits) operate the door or gate.** Two digits (0-99 sec or 00 for remain open) Engineer s code Relay code Relay code Relay 3 code*** Relay time Relay time Relay 3 time*** Notes: * If the red light does not illuminate, the engineer s code is incorrect. Follow instructions to return system to preset engineer s factory code. ** On the first loop of the flow chart its relay, second loop is relay and third loop is relay 3. *** Only for Art ART TERMINALS SW Relay command signal (active low) SW Relay command signal (active low) NC Relay normally closed contact NO Relay normally open contact C Relay common contact NC Relay normally closed contact NO Relay normally open contact C Relay common contact Max 4Vac/dc ART TERMINALS NO3 Relay 3 normally open contact C3 Relay 3 common contact NC Relay normally closed contact NO Relay normally open contact C Relay common contact NC Relay normally closed contact NO Relay normally open contact C Relay common contact Max 4Vac/dc /+ /4Vac/dc power input / /+ /4Vac/dc power input / TECHNICAL SPECIFICATIS Power requirements: /4V AC/DC, VA Power Consumption: On AC On DC Stand-by: 8mA Stand-by:.5mA Operating: 5mA Operating: 35.0mA Working Temperature: C VK8K/656 Series - Installation handbook EN - V 3.4-3/08/6

12 VK8K/656 Series 6 wire Bus videokit 8000 Series Surface and flush mounting door station installation INSTALLING A FLUSH MOUNTING DOOR STATI. Mount back box S (Fig. ) at 65 cm from ground level (Fig. );. If more than one flush box is needed, connect them by using the plastic spacers provided A (Fig. ); 3. If necessary finish and clean properly the module support fixing holes and all other holes B (Fig. ); 4. A rainshield D (Fig. 3 & 4) can be mounted using the fixing screws G (Fig. 4) to conceal possible wall finishing defects and protect against rain; In order to prevent water ingress we highly recommend using a silicon sealant between the wall and the back box and between the wall and the rainshield D (Fig.3); 5. Remove the fixing screws H (Fig. 5) and remove the plastic cover E (Fig. 5) of the module support; 6. Insert the modules F (Fig. 6) according the required configuration; 7. Insert the microphone of the door unit amplifier into the microphone hole X (Fig. 7); 8. Secure the modules by refitting the plastic cover E (Fig. 8) and using the screws H (Fig. 8); 9. Insert the hinge I (Fig. 9) and fix it with the two screws K (Fig. 9) provided; 0. Make all connections following accurately the wiring diagram provided. Check the installation and if necessary adjust speech levels using volume controls L (Fig. 9);. Lever the support R (Fig. 0) upwards and fix it to the back box with the screw M (Fig. ) using an alan key P (Fig. );. Conceal the screw using the plastic cover N (Fig. ) provided. INSTALLING A SURFACE MOUNTING DOOR STATI Fix the surface box on the wall at a distance of 65 cm between the top of the box and the ground (Fig. ). In order to prevent water ingress we highly recommend using a silicon sealant between the wall and the back box J (Fig.) and around all holes W (Fig.). To complete the installation follow the same steps described above for the flush box. Note: if additional holes are made in the box or rainshield, oxidation problems may appear unless the unprotected metal is coated with a protective paint. HOW TO REMOVE THE CARD NAME HOER To avoid damage to the module front plate, tape the side that will be in contact with the screwdriver blade; lnsert a flat screwdriver into the card-holder hole as shown in Fig. 3; Move the screwdriver to the left as shown in Fig. 4 to extract the card name holder; Edit the card name then replace it inside the holder and refit: insert the holder inside its housing from the left or right side then push the other side until it clips into place. VK8K/656 Series - Installation handbook EN - V 3.4-3/08/6

13 VK8K/656 Series 6 wire Bus videokit 8000 Series surface and flush mounting door station installation EXAMPLE: INSTALLING A TWO MODULE OUTDOOR STATI A S B B Fig. Fig. Fig. 3 D S F D E G Fig. 4 Fig. 5 H Fig. 6 X E I K L Fig. 7 Fig. 8 H Fig. 9 M J P N R W Fig. 0 Fig. Fig. Fig. 3 VK8K/656 Series - Installation handbook 3 Fig EN - V 3.4-3/08/6

14 VK8K/656 Series 6 wire Bus videokit Art " colour videophone 7 mm 44 mm 8 mm V V 4Vac 0Vac - A SW SW PT3 PT PT SW Fig. Fig. DESCRIPTI Surface mount videophone incorporating a 3.5 Hi-Res full colour active matrix LCD monitor specific for 6 wire videokit (VK4K, VRVK and VK8K range). It includes 4 buttons: camera recall, open door, service and privacy. LED s* indicate the privacy activated and open door. Programmable privacy duration and number of rings. Intercommunicating call and door call. Adjustments: call tone volume switch (3 levels), picture hue, contrast and brightness. * The operation of some LED s and the functions described may require additional cabling PUSH BUTTS Service push button. Shorts the terminal to GROUND (open collector 4Vdc 00mA max) while the button remain pressed. Camera recall button. Pick up the handset then press the button (Press once for door/gate, twice for and so on up to a maximum of 4 entrances): the relevant LED switches and the monitor switches on showing the video from the door panel. The speech is also live and the door can be opened by pressing. Door-open / intercommunicating call button. With the handset lifted and speech lines open to the entrance panel, press this button to open the door. If the terminal is properly connected the relevant LED remains switched until the door is closed. Intercommunication only works when the system is in stand-by condition. Switch 4 of the SW dip-switch selects the type of intercommunication: OFF Intercommunication between two apartments - pick up the handset and press the key button to call the videophone(s) in the other apartment. A busy tone will signal that the other videophone is in conversation with the door station and so cannot be called. Intercommunication between videophones in the same apartment - pick up the handset and press the key button one, two, three or four times to call videophone with extension address,, 3 or 4 (Set on dip-switch &3 of SW). Any intercommunicating conversation is always interrupted by an external call (i.e. External calls take priority). Privacy -OFF button. When the system is in stand-by, the pressing of this button activates (LED switched on) or disables (LED switched off) the privacy service. The service is automatically disabled when the programmed privacy time expires. When the service is enabled the videophone does not receive calls. VK8K/656 Series - Installation handbook EN - V 3.4-3/08/6

15 VK8K/656 Series 6 wire Bus videokit Art " colour videophone LEDS Door open LED. Can be used to indicate the status of a door or gate. It requires a switched Vdc connection to terminal. CTROLS SW Call tone volume controll (3 levels). Privacy /OFF LED. When the videophone is in stand-by, this LED signals the privacy service status ( = service enabled, OFF = service disabled). PT PT3 PT Brightness control. PT Hue control. PT3 Contrast control. SETTINGS (DIP-SWITCH) The videophone setup is carried out by the dip-switch banks. Switches Apartment Address OFF Switches,3 Extension Address OFF OFF OFF OFF 3 4 Switch 4 Intercommunication OFF Between videophones of the two apartment Between videophones in the same apartment Switches 5,6 Number of rings OFF OFF OFF 4 OFF 6 8 Switches 7,8 Privacy duration time OFF OFF 5 minutes OFF hours OFF 4 hours 8 hours WAY DIP-SWITCH (SW) The two way dip-switch adjusts the impedance of the video signal. The default setting is for both switches (75 Ohm): when there are more videophones in parallel connection (without video distributor) both switches must be only on the last videophone (looking at the connection order) while for all other videophones both switches must be set to OFF. VK8K/656 Series - Installation handbook EN - V 3.4-3/08/6

16 VK8K/656 Series 6 wire Bus videokit Art " colour videophone SIGNALS CNECTI BOARD 0Vdc Input/Output (As input 6 0Vdc 0, as output 0Vdc 0, max) Ground reference for terminal. Speech line output from handset s microphone and data signal (Approx. V in stand-by, 5V during a conversation) Speech line input toward the handset s loudspeaker (Approx. V in stand- by, approx. 3V during a conversation) V Balanced video signal sync.- V Balanced video signal sync.+ 4Vac A max power input A Local call input (5V in standby, 0V to trigger) Service button (open collector) active low output. The button goes active when the button is pressed (Open Collector 4Vdc 00mA max) Vdc input for door-open LED Speech line input toward the loudspeaker of the parallel telephone (Approx. V in stand-by, 3V during a conversation) Output switched ground for parallel telephone Output call tone for parallel telephone Input for door-open command from parallel telephone TECHNICAL SPECIFICATI Power Supply: Supplied by the BUS line, 0Vdc Power consumption: Stand-by: 50mA Max Operating: 00mA Max Working Temperature: C VK8K/656 Series - Installation handbook EN - V 3.4-3/08/6

17 VK8K/656 Series 6 wire Bus videokit 600 Series Videophone wall mounting instructions C D A F B E 35cm F A B C Fig. Fig. Fig. 3 A Fig. 4 G B Fig. 5 Fig. 6. In order to install the videophone, it is necessary to remove the cover, which contains all the electronics, from the base: firstly disconnect the handset from the videophone (by removing its plug from the videophone), then press lightly the bottom part of the videophone and simultaneously pulling outwards the upper part as shown in Fig... Put the base of the unit on the wall at approx 35cm from the finished floor to mark the points for the fixing holes A (Fig. ) remembering that the wires D (Fig. 3) must be fed through the hole E (Fig. 3). If you use the flush mounting box 503, embed it into the wall vertically at approx. 40cm from the finished floor and the base. 3. Following Fig. 3, make the holes A, insert the wall plugs B and fix the base with the screws C feeding the wires D into the hole E. If you have used the box 503, fix the base to the wall through the holes F using the screws C. 4. As shown in Fig., connect the wires to the removable terminals following the provided installation diagram. Connect the terminal blocks to the electronics contained in the cover as shown in Fig. 4B. Reinsert the handset and test system before closing. Note: Contrast and hue trimmers can be adjusted only if the videophone is open. Note while testing the system, it is advisable to hold the cover with your hand closing manually the hook switch of the handset (see Fig. 4B reference G ). 5. Once testing is complete and all the necessary adjustments are made, disconnect the handset from the cover and close the unit as shown in Fig. 5: first hook it on the bottom then push in the top until you hear the clip. 6. Reconnect the handset and hang it as shown in Fig. 6. VK8K/656 Series - Installation handbook EN - V 3.4-3/08/6

18 VK8K/656 Series 6 wire Bus videokit Installation diagrams NOTES AND SUGGESTIS All diagrams refer to all kits versions: flush or surface, colour or black & white. Dashed connections refer to optional connections ( Local bell, Push to exit & Door monitor ). Some diagrams show how to connect a Vdc electric lock: these directions are suitable for all diagrams in this manual. Each time a setting is changed on a videophone (address, extension, number of rings etc.), the videophone must be disconnected from the relevant connection board then after a few seconds reconnected again to allow the recognizing of the new setting. All diagrams shown are valid for B&W or colour systems with surface or flush mount door station. DECLETI OF RESPSIBILITY This manual has been written and revised carefully. The instructions and the descriptions which are included in it are referred to VIDEX parts and are correct at the time of print. However, subsequent VIDEX parts and manuals, can be subject to changes without notice. VIDEX Electronics S.p.A. cannot be held responsible for damages caused directly or indirectly by errors, omissions or discrepancies between the VIDEX parts and the Manual. WE RECOMMEND This equipment is installed by a Competent Electrician, Security on Communications Engineer VK8K/656 Series - Installation handbook EN - V 3.4-3/08/6

19 VK8K/656 Series 6 wire Bus videokit Installation diagrams VIDEOKIT VK8K-/656, VK8K-S/656 Local Bell Door Monitor V V _ A SW SW Art.656 Address N. Ext. In caso di modifica alle impostazioni dei dip switch del videocitofono o del posto esterno, togliere temporaneamente l'alimentazione di rete. In order to make the system recognize any modification of the videophone's and outdoor station's dip-switch setting, temporarily disconnect the system from the mains and reconnect Using Electric Lock Vdc 0. Max Con serratura elettrica Vdc 0. Max Push to Exit Art Art Title: Titolo: Videx Electronics S.p.A. Via del Lavoro, 6300 Monte Giberto (AP) Phone: Fax info@videx.it Notes: Note: Data creazione: Foglio 7//05 Data modifica: 7//05 Autore: Marco Rongoni Cod.File: / vk8k6h-00.dwg VK8K/656 Series - Installation handbook EN - V 3.4-3/08/6

20 VK8K/656 Series 6 wire Bus videokit Installation diagrams VIDEOKIT VK8K-/656, VK8K-S/656 Using Electric Lock Vdc 0. Max Con serratura elettrica Vdc 0. Max Local Bell Art Push to Exit Art A V V _ SW SW Art.656 Address N. Ext. Local Bell A V V _ SW SW Art.656 Address N. Ext. In caso di modifica alle impostazioni dei dip switch del videocitofono o del posto esterno, togliere temporaneamente l'alimentazione di rete. In order to make the system recognize any modification of the videophone's and outdoor station's dip-switch setting, temporarily disconnect the system from the mains and reconnect VK8K/656 Series - Installation handbook 0 04//05 7//05 Marco Rongoni vk8k6h-003.dwg EN - V 3.4-3/08/6

21 VK8K/656 Series 6 wire Bus videokit Installation diagrams VIDEOKIT VK8KC-/656, VK8KC-S/656 Local Bell V V _ A SW SW Art.656 Address N. Ext. Door Monitor In caso di modifica alle impostazioni dei dip switch del videocitofono o del posto esterno, togliere temporaneamente l'alimentazione di rete. In order to make the system recognize any modification of the videophone's and outdoor station's dip-switch setting, temporarily disconnect the system from the mains and reconnect + Art.8800 Using Electric Lock Vdc 0. Max Con serratura elettrica Vdc 0. Max Push to Exit Art Art Title: Titolo: Videx Electronics S.p.A. Via del Lavoro, Monte Giberto (FM) Phone: Fax info@videx.it Notes: Note: Data creazione: Foglio /0/05 Data modifica: 7//05 Autore: Marco Rongoni Cod.File: / vk8k6h-004.dwg VK8K/656 Series - Installation handbook EN - V 3.4-3/08/6

22 VK8K/656 Series 6 wire Bus videokit Installation diagrams VIDEOKIT VK8KC-/656, VK8KC-S/656 In caso di modifica alle impostazioni dei dip switch del videocitofono o del posto esterno, togliere temporaneamente l'alimentazione di rete. In order to make the system recognize any modification of the videophone's and outdoor station's dip-switch setting, temporarily disconnect the system from the mains and reconnect Local Bell Local Bell + Art.8800 Using Electric Lock Vdc 0. Max Con serratura elettrica Vdc 0. Max Push to Exit Art Art SW SW SW SW _ V V A Art.656 Address N. Ext. _ V V A Art.656 Address N. Ext. 7//05 0//05 Marco Rongoni vk8k6h-005.dwg VK8K/656 Series - Installation handbook EN - V 3.4-3/08/6

23 VK8K/656 Series 6 wire Bus videokit Installation diagrams VIDEOKIT VK8K-/656, VK8K-S/656 WITH ADDITIAL INTERCOM AND EXTENSI SOUNDER Local Bell Affinche qualsiasi modifica alle impostazioni dei dip switch del videocitofono o del posto esterno venga riconosciuta dal sistema, è necessario togliere l'alimentazione di rete all'impianto e restituirla. V _ V A SW SW In order to make the system recognize any modification of the videophone's and outdoor station's dip-switch setting temporarily disconnect the system from the mains and reconnect Art.656 Address N. Ext. YELLOW VOL.REG. BLACK RED 4 GREEN Using Electric Lock Vdc 0. Max Con serratura elettrica Vdc 0. Max Push to Exit Art Art Title: Titolo: Videx Electronics S.p.A. Via del Lavoro, Monte Giberto (FM) Phone: Fax info@videx.it Notes: Note: Data creazione: Foglio 0//05 Data modifica: 0//05 Autore: Marco Rongoni Cod.File: / vk8k6h-006.dwg VK8K/656 Series - Installation handbook EN - V 3.4-3/08/6

24 VK8K/656 Series 6 wire Bus videokit Installation diagrams VIDEOKIT VK8K-/656, VK8K-S/656 WITH ADDITIAL DOOR PANEL FOR ENTRANCES SYSTEM Local Bell In caso di modifica alle impostazioni dei dip switch del videocitofono o del posto esterno, togliere temporaneamente l'alimentazione di rete. _ V V A SW SW In order to make the system recognize any modification of the videophone's and outdoor station's dip-switch setting, temporarily disconnect the system from the mains and reconnect Art.656 Address N. Ext. 5 NO Push to Exit 4 3 Art.506N NC CO NO NC C0 Push to Exit Using Electric Lock Vdc 0. Max Con serratura elettrica Vdc 0. Max Art ID: Art Art ID: Title: Titolo: Videx Electronics S.p.A. Via del Lavoro, Monte Giberto (FM) Phone: Fax info@videx.it Notes: Note: Data creazione: Foglio 0//05 Data modifica: 0//05 Autore: Marco Rongoni Cod.File: / vk8k6h-007.dwg VK8K/656 Series - Installation handbook EN - V 3.4-3/08/6

25 VK8K/656 Series 6 wire Bus videokit Installation diagrams VIDEOKIT VK8KC-/656, VK8KC-S/656 WITH 3 ADDITIAL VIDEOPHES Push to Exit + Art.8800 Art A V V _ SW SW In caso di modifica alle impostazioni dei dip switch del videocitofono o del posto esterno, togliere temporaneamente l'alimentazione di rete. In order to make the system recognize any modification of the videophone's and outdoor station's dip-switch setting, temporarily disconnect the system from the mains and reconnect SW Using Electric Lock Vdc 0. Max Con serratura elettrica Vdc 0. Max Art _ V V _ V V A SW A SW SW Art.656 Address N. Art.656 Address N. Ext. Art.656 Address N. Ext. 3 Ext. 0//05 0//05 Marco Rongoni vk8k6h-008.dwg VK8K/656 Series - Installation handbook EN - V 3.4-3/08/6

26 VK8K/656 Series 6 wire Bus videokit Installation diagrams VIDEOKIT VK8K-/656 - VK8K-S/656 WITH ART. 36 Using Electric Lock Vdc 0. Max Con serratura elettrica Vdc 0. Max Local Bell Art Push to Exit Art A V V _ SW SW Art.656 Address N. Ext. Local Bell A V V _ In caso di modifica alle impostazioni dei dip switch del videocitofono o del posto esterno, togliere temporaneamente l'alimentazione di rete. In order to make the system recognize any modification of the videophone's and outdoor station's dip-switch setting, temporarily disconnect the system from the mains and reconnect SW SW Art.656 Address N. Ext. VK8K/656 Series - Installation handbook 6 /0/05 7//05 Marco Rongoni vk8k6h-00.dwg EN - V 3.4-3/08/6

27 VK8K/656 Series 6 wire Bus videokit Installation diagrams TWO ENTRANCES SYSTEM INSTALLATI V V GND +0V Art.506N NO NC CO NO NC C0 30V + - 8Vdc ART. 33/8 Push to Exit Push to Exit Art Art ID: Title: Titolo: Videx Electronics S.p.A. Notes: Via del Lavoro, Monte Giberto (FM) Phone: Fax Note: - info@videx.it VK8K/656 Series - Installation handbook 7 ID: Data creazione: 8/0/05 Data modifica: 8/0/05 Autore: Cod.File: Foglio Marco Rongoni / vk8k--00-e.dwg EN - V 3.4-3/08/6

28 MANUFACTURER VIDEX ELECTRICS S.P.A. Via del Lavoro, Monte Giberto (FM) Italy Tel (+39) Fax (+39) info@videx.it CUSTOMER SUPPORT All Countries: VIDEX ELECTRICS S.P.A. - technical@videx.it Tel: Fax: UK Customers: VIDEX SECURITY LTD Tech Line: Fax: Main UK office: VIDEX SECURITY LTD Osprey Trinity Park Trinity Way E4 8TD Phone: (+44) Fax: (+44) marketing@videx-security.com Northern UK office: VIDEX SECURITY LTD Unit 4-7 Chillingham Industrial Estate Chapman Street NEWCASTLE UP TYNE - NE6 XX Tech Line: (+44) Phone: (+44) Fax: (+44) Greece office: VIDEX HELLAS Electronics 48 Filolaou Str. 633 ATHENS Phone: (+30) (+30) Fax: (+30) videx@videx.gr Danish office: VIDEX DANMARK Hammershusgade 5 DK-00 COPENHAGEN Phone: (+45) Fax: (+45) videx@videx.dk Benelux office: NESTOR COMPANY NV E3 laan, 93 B-9800 Deinze Phone: (+3) Fax: (+3) info@videx.be Dutch office: NESTOR COMPANY BV Business Center Twente (BCT) Grotestraat, 64 NL-76 GM Borne info@videxintercom.nl The product is CE marked demonstrating its conformity and is for distribution within all member states of the EU with no restrictions. This product follows the provisions of the European Directives 04/30/EU (EMC); 04/35/EU (LVD); 0/65/EU (RoHS): CE marking 93/68/EEC.