Velocitykvm-4, 5, 8, 24, 28, 34, 35 & 38 Single-Link and Dual-Link Fiber Extension Systems

Transcription

1 Multi-Mode Fiber Extension Systems Velocitykvm-4, 5, 8, 24, 28, 34, 35 & 38 Single-Link and Dual-Link Fiber Extension Systems Thinklogical, LLC 100 Washington Street Milford, Connecticut U.S.A. Telephone: Fax: Extend Distribute Innovate

2 Extend Distribute Innovate Copyright Notice Copyright All rights reserved. Printed in the U.S.A. Thinklogical, LLC 100 Washington Street Milford, Connecticut U.S.A. Telephone: All trademarks and service marks are property of their respective owners. Subject: VelocityKVM Fiber Extension Product Manual Revision: F, November 2011 VelocityKVM, Rev F 2 November 2011

3 Table of Contents PREFACE... 5 Conventions Used in this Manual... 5 INTRODUCTION... 5 The Logical Solution... 5 Theory of Operation... 6 The Fiber Extension System... 7 Available Options... 7 System Features... 8 VelocityKVM Extender Options... 8 Technical Specifications (Table 1) HARDWARE Contents Desktop or Rack Mount Device Cooling Front Panel Display and Buttons Connecting the VelocityKVM Extender Types of Connectors Fiber Cable Transmitter Receiver Serial Port Rear Panel Views and Hardware Connections Peripheral and Update Ports Fiber and Video Ports Cables Installation Set Up Firmware Upgrades Front Panel Usage General Front Panel Usage LOS and DES OK Signals LOS and DES OK Signals (Table 2) Saving Changes Restoring Factory Defaults Naming the Transmitter Unit REGULATORY & SAFETY COMPLIANCE Safety Requirements Symbols Found on Our Products Regulatory Compliance North America Australia & New Zealand European Union Declaration of Conformity Standards with Which Our Products Comply Supplementary Information VelocityKVM, Rev F 3 November 2011

4 Product Serial Number Connection to Our Products HOW TO CONTACT US Customer Support Website Telephone Fax Product Support Limited Warranty Information Our Address APPENDIX A: Thinklogical s Full Line of VelocityKVM Extenders APPENDIX B: Quick Start Guides VelocityKVM VelocityKVM VelocityKVM VelocityKVM VelocityKVM VelocityKVM VelocityKVM VelocityKVM APPENDIX C: Automatic Fail-Over Option APPENDIX D: Keyboard Mouse Audio Control Options...52 VelocityKVM, Rev F 4 November 2011

5 PREFACE Conventions Used in this Manual As you read this manual you will notice certain conventions that bring your attention to important information. These are Notes and Warnings. Examples are shown below. Note: Important Notes appear in blue text preceded by a yellow exclamation point symbol, like this. A note is meant to call the reader s attention to helpful information at a point in the text that is relevant to the subject being discussed. Warning! All Warnings appear in red text, followed by blue text, and preceded by a red stop sign, like this. A warning is meant to call the reader s attention to critical information at a point in the text that is relevant to the subject being discussed. INTRODUCTION The Logical Solution VelocityKVM Extension Systems are designed for high performance visual applications that require video as well as peripheral support. The system allows users, via optical fiber, to station and operate a digital or RGB (KVM System-5 only) monitor(s) and peripherals from just a few meters away to up to 40 kilometers away from the controlling computer, securely and without loss of resolution. The VelocityKVM system is designed to support PS2, full duplex stereo audio, serial (RS-232), USB 1.0 (HID) and USB 1.1. Available options include: USB 2.0 (up to 480 Mbps) IEEE 1394 (9-pin FireWire) device ports HID (eliminates USB 1.1 for added security) Separate Data Paths for keyboard/mouse RS-422 serial port for controlling broadcast equipment Automatic Fail-Over (See Appendix C, pg. 51) VelocityKVM products are ideally suited for a wide range of applications in the broadcast and postproduction field, as well as command and control centers, universities, large scale digital signage and other commercial KVM applications. See Option Configuration Diagrams (pgs. 9-10) and Appendix A, Complete Line of Thinklogical s VelocityKVM Extenders (pg. 39). VelocityKVM, Rev F 5 November 2011

6 Theory of Operation MRTS Technology 6.25 Gbps. Allows for Full Frame Rate Transmission of Uncompressed DVI Powered by Thinklogical s cutting edge, patent-pending MRTS (Multi Rate Transmission System) technology, this KVM extension system transports every frame of a DVI video stream seamlessly with no compression or dropped frames. In addition, all high speed peripherals function with no latency. Leveraging standard SFP+ transceivers, the system allows for the use of either multi-mode or singlemode fiber optic cable. The System The VelocityKVM Extension System has a simple transmitter/receiver design which allows for ease of installation and straight-forward deployment. Depending on the user s infrastructure, the transmitter and the receiver can be connected by a multi-mode or single-mode fiber optic cable. The transmitter unit connects to the CPU with the supplied peripheral cables. In addition, a local video, keyboard and mouse port is available on the transmitter. The receiver unit provides connections to the user interface devices. Why Fiber? The limit on how much bandwidth or data that can be carried across a copper line can become a bottleneck for enterprise access and ultimately, for revenue. This bottleneck often appears in heavyvolume, metropolitan area networks. Fiber Optic Cable alleviates this problem by offering substantially greater bandwidth. The VelocityKVM Distance (up to 350m using 50/125µm fiber) Multi-mode fiber is designed for transmission distances such as those found within a single building or facility and thus, is ideal for multi-channel television broadcast systems. Multi-mode fiber may be used to send video signals from room to room or floor to floor. The VelocityKVM allows for video and peripheral transmission distances up to 350 meters using 50/125µm fiber, making it an ideal solution for in-house applications. Advanced Top Quality Video Transmission Fiber Optic Cable has emerged as a logical solution for next-generation signal routing. The VelocityKVM product family harnesses this capability and ensures long distance, error-free transmission with no frame or bit dropping and complete immunity to interference. The end result is no degradation of the video or peripheral signal whatsoever. VelocityKVM, Rev F 6 November 2011

7 The VelocityKVM-24U (DVI 2 Display) Multi-Mode Fiber Extension System (with USB 2.0 option) The Fiber System Each system consists of a transmitter and a receiver connected by fiber optic cables. The transmitter unit connects to the source computer with standard cables and the receiver unit provides connections to the user interface devices. Standard VelocityKVM Extenders support PS2, full duplex stereo audio, serial (RS-232), USB 1.0 (HID) and USB 1.1. Options Part Numbers: Each model s part number indicates features included on that particular model. USB 2.0 (high speed up to 480 Mbps) is indicated by a U in the part number (shown above). HID, which includes USB HID only, is indicated by an H (shown below), and IEEE 1394 (9-Pin FireWire), is indicated by an F in the part number (below, bottom). See pages 9 and 10 for the full line of VelocityKVM Extender options. Also see page 42 for more on numbering formats. VelocityKVM, Rev F 7 November 2011

8 System Features Each VelocityKVM Fiber system includes the following features: Supports all single-link DVI video resolutions (VelocityKVM Extension System-5 analog RGB resolutions as well). Supports all Dual-Link DVI resolutions (VelocityKVM System-8, VelocityKVM System-28, VelocityKVM System-38) Gbps signal transmission via fiber optic cable; No RF interference. Requires one to five fiber optic cables, depending on model and application. Flawless image quality with no frame dropping. Local KVM connections on transmitter. Additional video output(s) on the receiver. Extends KVM, audio and serial signals up to 350 meters using 50/125µm multi-mode fiber and up to 1000 meters using type OM4 fiber. Extends KVM, audio and serial signals up to 40 kilometers using single mode fiber. USB HID compliant, 4-port hub. Full USB 1.1 compliant, 4-port hub. BNC Stereo Emitter (3D) Full duplex stereo audio (Optional) USB 2.0 compliant (high speed 480 Mbps, 4 port hub). (Optional) IEEE1394 FireWire 9-pin hub (Requires 2 additional fiber optic cables.) (Optional) HID only, which eliminates USB 1.1 for added security (Optional) Automatic Fail-Over (see page 48) (Optional) Separate Data Paths for keyboard/mouse (Optional) RS422 serial port for controlling broadcast equipment DDC2B/EDID complaint. Fully compatible with all of Thinklogical s VXRouter line of products. Full keyboard and mouse emulation through the transmitter Simple plug and play Thinklogical s VelocityKVM Extenders are designed and identified as Class 1 Laser products. VelocityKVM Extender Options (The examples on pages 9 and 10 are shown on the VelocityKVM-24 Tx and Rx with LC-type connectors. All extender models follow the same format for all connector types and option configurations.) VelocityKVM, Rev F 8 November 2011

9 VelocityKVM, Rev F 9 November 2011 VEL-00DM24-LCTX VEL-E00M24-LCTX VEL-E0DM24-LCTX VEL-F00M24-LCTX VEL-F0DM24-LCTX VEL-H00M24-LCTX VEL-H0DM24-LCTX VelocityKVM Extender Options D, E, ED, F, FD, H & HD (Examples below are shown on the VelocityKVM-24 Tx and Rx. All extender models follow the same format for option configurations.) TRANSMITTERS RECEIVERS Vel-D (Separate Data Paths, USB 1.1, USB HID, no USB 2.0) Vel-E (USB 2.0, USB HID, FireWire, no USB 1.1) Vel-ED (Separate Data Paths, USB 2.0, USB HID, FireWire, no USB 1.1) Vel-F (USB 1.1, USB HID, FireWire, no USB 2.0) Vel-FD (Separate Data Paths, USB 1.1, USB HID, FireWire, no USB 2.0) Vel-H (USB HID, no USB 1.1 or USB 2.0) Vel-HD (Separate Data Paths, USB HID, no USB 1.1 or USB 2.0) VEL-00DM24-LCRX VEL-E00M24-LCRX VEL-E0DM24-LCRX VEL-F00M24-LCRX VEL-F0DM24-LCRX VEL-H00M24-LCRX VEL-H0DM24-LCRX

10 VelocityKVM, Rev F 10 November 2011

11 Technical Specifications Each Thinklogical VelocityKVM system is designed to the following specifications: TABLE 1 Copper Connectors Transmitter Video System 4, 8 DVI-D (2); System 24, 28, 34, 38 DVI- D (4); System 35 DVI-D (3); System 5 DVI-I (2) Audio MIC/Line 3.5mm Jack Serial Port DB9 Female Stereo Emitter 50Ω BNC IEEE Pin FireWire (optional) USB 1.0 (HID) USB B USB 1.1 USB B USB 2.0 USB B (optional) USB Local Kybd. USB A USB Local Mouse USB A PS2 Keyboard MiniDIN 6 Female PS2 Mouse MiniDIN 6 Female PS2 Local Kybd. MiniDIN 6 Female PS2 Local Mouse MiniDIN 6 Female Firmware Updates USB B (3) Fiber Connectors LC, SC or ST Receiver Video System 4, 8, 28, 38 DVI-D (2); System 24, 34 DVI- D (4), System 35 DVI-D (3); System 5 DVI-I (2) Audio MIC/Line 3.5mm Jack Serial Port DB9 Male Stereo Emitter BNC IEEE Pin FireWire (optional) USB 1.0 (HID) USB A (4) USB 1.1 USB A (4) USB 2.0 USB A (4) (optional) PS2 Keyboard MiniDIN 6 Female PS2 Mouse MiniDIN 6 Female Firmware Updates USB B Fiber Connectors LC, SC, or ST VelocityKVM, Rev F 11 November 2011

12 Electrical Cables (supplied with transmitters) CBL MR, DVI-D M to M: -4, -5, -24(2), -28, -34(4), -35(3) CBL MR, HD15 to DVI-A: -5 CBL MR, DVI-D Male to Male, Dual-Link: -8, -28, -38(2) KIT R, Audio Kit, 6FT: 1 each KIT R Audio Kit contains the following: CBL FR 6 pin MiniDIN Male to Male Cable, 6FT (2) CBL FR USB A-B Cable, 6FT (2) CBL FR 3.5mm Male to 3.5mm Male Plug, 6FT (2) CBL FR DB9 Male to DB9 Female Cable, 6FT (1) CBL FR BNC Male to BNC Male Cable, 50Ω, 6FT (1) Video Resolution Optical Cable Optical Distance Operating Temp and Humidity Dimensions Weights All Single-Link DVI Resolutions: System 4, 5, 24, 34, 35 All Single & Dual-Link Resolutions: System 8, 28, 38 Fiber Type: 50 or 62.5 micron, Multi-mode Required: 1, 2, 3, 4 or 5 depending upon application. (Not supplied) Up to 65 meters with Type OM1 Up to 350 meters with Type OM2 Up to 650 meters with Type OM3 Up to 1000 meters with Type OM4 0 to 50 C (32 to 122 F), 5% to 95% RH, non-conde nsing Height: 1.72 (4.4cm) ±.039 ;.100cm Depth: (45.8cm)* ±.039 ;.100cm Width: (44.5cm) ±.039 ;.100cm Weight: 11 lbs (4.99kg) each Shipping Weight: 27 lbs (12.25 kg) Transmitter and Receiver Supply Voltage VAC, Hz, Universal AC power supply Power Consumption <40 Watts per unit Compliance Approvals for US, Canada, and European Union Warranty 12 months from date of purchase. Extended warranties available. TABLE 1: Technical Specifications VelocityKVM, Rev F 12 November 2011

13 HARDWARE Contents When you receive your Thinklogical VelocityKVM Extender, you should find the following items: VelocityKVM Extender Transmitter VelocityKVM Extender Receiver AC power cord, PWR R (International connections may differ) Qty 2 VelocityKVM Extender Cables Video Cable, 2 Meters See Technical Specs, pg. 11 Audio Cable Kit (8 pcs.), 6 Feet, KIT R Qty 1 VelocityKVM Extender Product Manual CD Product Quick Start Guide All physical connections to the product use industry-standard connectors. Desktop or Rack Mount Device You may choose to place your unit on a shelf or desktop (rubber feet included), or rack mount it using the supplied mounting brackets (EIA 19 rack mountable). The front panel should be visible and unobstructed so that the front panel buttons and LCD display are accessible. All connections are made to the rear of the chassis. The VelocityKVM Extender chassis does not need to be opened or accessed. The sturdy metal case allows units to be stacked as needed (maximum of four units per stack, with a minimum of two inches of clearance between stacks for adequate ventilation). Mounting Bracket Removal VelocityKVM, Rev F 13 November 2011

14 Cooling The VelocityKVM Extender System uses two DC fans to move air horizontally through the enclosure. Note: Be sure to leave adequate ventilation space on both sides of the units (2 minimum), especially if the units are being stacked. Front Panel Display and Buttons The front-panel LCD should be visible and accessible for system setup. The front panel buttons are used to configure special video settings and to review existing VelocityKVM Extender configurations. More detailed information on the Front Panel can be found in the Front Panel Usage section (Page 21). VelocityKVM-24 Extender Front Panel LCD Connecting the VelocityKVM Extender Types of Connections All physical connections to the product use industry-standard connectors. Non-supplied cables that may be needed are commercially available. All connections are found on the rear of the unit. Fiber Cable Fiber optic cables run between the Transmitter unit (near your CPU) and the Receiver unit (near your desktop devices). The standard multi-mode fiber optic cables must be 50 or 62.5 micron, terminated with LC, ST or SC- type fiber optic connectors. Be careful not to kink or pinch the fiber optic cable as it is being installed and keep all bend radii to no less than 3 inches (76.2mm). Transmitter The transmitter unit connects to the computer at the DVI In port using a DVI-D male-to-male cable (CBL MR for single-link and/or CBL MR for dual-link) which is supplied with the system. The connections to the VelocityKVM Extender Transmitters can be viewed in detail in the REAR PANEL VIEW section of this manual. VelocityKVM, Rev F 14 November 2011

15 Receiver The receiver unit connects to a video monitor using a DVI-D male-to-male cable. Peripherals connect with their own standard cables. The connections to the VelocityKVM Extender Receivers can be viewed in detail in the REAR PANEL VIEW section of this manual. Receiver Serial Port The serial port is a DB9 male connector. This DB9 interface connects to your touch screen, tablet, tape controller, etc., if needed, using a DB9 Male to DB9 Female Cable (CBL F is supplied in KIT R, which is provided with the system). An RS422 option for controlling broadcast equipment is also available. Rear Panel Views and Hardware Connections Peripheral and Update Ports The following Transmitter and Receiver rear panel diagrams explain the functions of the various peripheral device ports, including available Stereo Emitter, USB 2.0 and FireWire options and their LED indicators for all VelocityKVM Extenders. Refer to the Quick Start Guides in Appendix B for more information. VelocityKVM, Rev F 15 November 2011

16 VelocityKVM Transmitters and Receivers with the FireWire Option: Peripheral and Update Ports, LED Indicators NOTE: The FireWire option requires 2 additional Fiber Optic Cables. FireWire (Fibers & IN Port) Audio IN (source) RS-232 Local Keyboard/Mouse OUT (HID or PS2) PS2 Keyboard/Mouse IN (from source) FireWire Indicator LEDs Stereo Emitter IN (3D) PWR: Unit power On/Off Audio OUT CP: ON=Cable Powered (from microphone) CLINK: ON=CPU connected (linked) FOL: (Fiber Optic Link) ON=connection, BLINKING=no connection Unmarked LEDs are non-functioning USB HID & USB 2.0 IN Transmitter Update Ports FireWire (Fibers & OUT Port) Audio OUT (speakers) RS-232 USB HID, PS2 and USB 2.0 OUT FireWire Indicator LEDs PWR: Unit power On/Off CP: ON=Cable Powered CLINK: ON=CPU connected (linked) FOL: (Fiber Optic Link) ON=connection, BLINKING=no connection Unmarked LEDs are non-functioning Audio IN (microphone) Stereo Emitter OUT (3D) Receiver VelocityKVM, Rev F 16 November 2011

17 Fiber and Video Ports The following transmitter and receiver rear panel diagrams explain the functions of the fiber optic cable input and output ports and the video input and output ports for each of the VelocityKVM Extenders. For the fiber connections, Optical Fiber L1, which carries both DATA from Tx to Rx and VIDEO, is in purple, Optical Fiber L2, which carries DATA from Rx to Tx, is in blue and all VIDEO ONLY fibers are in red. Refer to the Quick Start Guides in Appendix B (pg ) for more information. USE ONLY WITH 250V FUSE USE ONLY WITH 250V FUSE USE ONLY WITH 250V FUSE USE ONLY WITH 250V FUSE VelocityKVM, Rev F 17 November 2011

18 Velocity-8 KVM Multi-Mode Extender Dual-Link DVI Transmitter PWR FOL CP CLINK 1 L1 L2 L3 DVI IN DUAL-LINK DVI OUT DUAL-LINK L1 Fiber: Data Tx to Rx & Video Primary L2 Fiber: Data Rx to Tx L3 Fiber: Video Secondary SER IAL PORT STEREO EMITTER INPUT LINE IN MIC OUT HID P S 2 LOCAL FROM CPU USB 1.1 PS/2 or USB connectors USB HID UPDATES DEV HOST CTRL CAUTION! Replace with same type and rating fuse. USE ONLY WITH 250V FUSE V-,0.5A, 50/60 Hz T 2A,250VAC Dual-Link DVI OUT (local) Dual-Link DVI IN (from source) L2 Fiber: Data Rx to Tx L1 Fiber: Data Tx to Rx & Video Primary L3 Fiber: Video Secondary Receiver PWR FOL L2 L1 L3 DVI OUT DDC DUAL-LINK DVI OUT DUAL-LINK SER IAL PORT STEREO EMITTER USB 2.0 USB HID USB 1.1 OUTPUT LINE OUT MIC IN P S 2 U P D A T E S HOST CTRL CAUTION! Replace with same type and rating fuse V-,0.5A, 50/60 Hz T 2A,250VAC USE ONLY WITH 250V FUSE Dual-Link DVI OUT (Secondary) Dual-Link DVI OUT (DDC) Velocity-24 KVM Multi-Mode Extender DVI 2 Display Transmitter L1 Fiber: Data Tx to Rx & Video 1 L2 Fiber: Data Rx to Tx L3 Fiber: Video 2 PWR FOL CP CLINK L1 L2 L3 1 3 DVI IN 1 SER IAL PORT DVI OUT 1 DVI IN 2 DVI OUT 2 STEREO EMITTER INPUT LINE IN MIC OUT HID P S 2 LOCAL FROM CPU USB 1.1 PS/2 or USB connectors USB HID UPDATES DEV HOST CTRL CAUTION! Replace with same type and rating fuse. USE ONLY WITH 250V FUSE V-,0.5A, 50/60 Hz T 2A,250VAC DVI OUT 2 (local) DVI IN 2 (from source) DVI OUT 1 (local) DVI IN 1 (from source) L2 Fiber: Data Rx to Tx L1 Fiber: Data Tx to Rx & Video 1 L3 Fiber: Video 2 Receiver PWR USB 2.0 FOL L2 L1 L3 SER IAL PORT DVI OUT 1 DDC DVI OUT 1 DVI OUT 2 DDC DVI OUT 2 STEREO EMITTER OUTPUT LINE OUT MIC IN USB HID P S 2 USB 1.1 U P D A T E S HOST CTRL CAUTION! Replace with same type and rating fuse V-,0.5A, 50/60 Hz T 2A,250VAC USE ONLY WITH 250V FUSE DVI OUT 2 (Secondary) DVI OUT 2 (DDC) DVI OUT 1 (Secondary) DVI OUT 1 (DDC) VelocityKVM, Rev F 18 November 2011

19 USE ONLY WITH 250V FUSE USE ONLY WITH 250V FUSE USE ONLY WITH 250V FUSE USE ONLY WITH 250V FUSE VelocityKVM, Rev F 19 November 2011

20 USE ONLY WITH 250V FUSE USE ONLY WITH 250V FUSE USE ONLY WITH 250V FUSE USE ONLY WITH 250V FUSE VelocityKVM, Rev F 20 November 2011

21 Cables Depending on the VelocityKVM model, use one of the following video cables: Single-link: DVI-D Male Cable, 2 Meters (CBL MR) Single-link: DVI-I Male Cable, 2 Meters (CBL MR) RGB: HD15 to DVI-A Male Cable, 2 Meters (CBL MR) - VelocityKVM-5, Qty 1 Dual-link: DVI-D Male Cable, 2 Meters (CBL MR) VelocityKVM, Rev F 21 November 2011

22 VelocityKVM, Rev F 22 November 2011

23 Peripheral Cables: KIT R Audio Cable Kit (8 pcs.) Qty 1, all models 2 each 6 pin mini din (6 ) 2 each USB A-B (6 ) 2 each 3.5mm to 3.5mm plug (6 ) 1 each DB9M to DB9F (6 ) 1 each BNC male to male, 50Ω (6 ) KIT-5 Cables (Included) Installation All physical connections to the product use industry-standard connectors. Non-supplied cables are commercially available. All connections are found on the rear of the unit. Refer to the Quick Start Guides in Appendix B (pg ) for more information. Set-Up Firmware Upgrades Firmware upgrades are available through Thinklogical. Please call for assistance: Front Panel Usage VelocityKVM, Rev F 23 November 2011

24 General Front Panel Usage Once the system is powered up, the initial Transmitter display is shown as follows: Thinklogical Velocity Tx VXX.XX The company name is listed on the first line of the display. The model and software version (VXX.XX) of the unit is displayed on the second line. By pressing the down arrow the VelocityKVM Extender allows you to enter into the main menu. The main root menu items are displayed with an *. They are as follows: *System *DDC Once a *root menu item is displayed, you can then use the left arrow or right arrow to review settings or make changes, if allowed. SFP LOS and SFP Des OK Signals In the *System root menu, scrolling right or left will bring you to the SFP Loss of Signal and SFP Des OK Signal menus. The SFP Loss of Signal menu provides confirmation of lost or unused video signals at the Receiver and of lost or unused data-return signals at the Transmitter. A lost/unused signal will be indicated by a 1 at SFPs 1 through 4 on a Receiver and by a 1 at SFP 1 on a Transmitter. If only 2 SFPs are in use, as in a VelocityKVM-24 Receiver, SFPs 3 and 4 will always indicate that no signal is present (1). The Des OK Signal menu provides confirmation that a good deserializer signal is detected at the Receiver and Transmitter SFPs. A good signal will be indicated by a 1 at SFPs 1 through 4. If only 2 SFPs are in use, as in a VelocityKVM-24, SFPs 3 and 4 will always indicate that no signal is present (1). Fiber L1 on the Transmitter and L2 on the Receiver are always transmitting light. The SFPs connected to fibers L3, L4 and L5 will not transmit light until a video signal is applied to the Transmitter s DVI IN connector. VelocityKVM, Rev F 24 November 2011

25 The following table shows the expected SFP Loss of Signal and Des OK Signal indications for each model of a properly connected VelocityKVM Receiver and Transmitter: TABLE 2: SFP Loss Of Signal and DES OK Signal LCD Indicators The VelocityKVM Extender menu functionality is as follows (Some menu options may not be available on all models.): TRANSMITTER: VelocityKVM, Rev F 25 November 2011

26 Display Modifiable Description *System LS Connected NO Indicates fiber status from TX to RX. (0=connected) Tx Ctrl Name TX Only Name entered on TX unit is displayed on RX unit. Load Defaults YES Loads factory default video configurations. Store Values YES Store video configurations. KM Device NO Revision of the VelocityKVM portion that plugs into CPU. KM Remote Host NO Revision of the VelocityVKM Host on the RX unit. KM Local Host NO Revision of the VelocityVKM Host on the TX unit. TX Control NO Revision of the TX unit laser and front panel control. RX Control NO Revision of the RX unit laser and front panel control. FPGA Version NO Revision of the FPGA used for video generation. Serial Number NO 2 digits each for DDMMYY and 2 or 3 unique digits Debug Values YES Factory Use. Allow FPGA Update NO Select YES to enable update Aud/USB Reset En YES Enable/disable USB 1.1 reset, lost Tx/Rx link LS Deserializer OK NO 1=Yes 0=No SFP Loss of Signal NO Indicates loss of SFP signal. (1= not connected) Temp in Celsius NO IN=PCB temp (max=70) EX=FPGA temp (max=85) KMASS Card ID NO 0E = original Video Card ID NO 08=single 09=dual head 0A=dual link 0B=RGB USB 2.0 Card ID NO 08=original 09=SoDimm *DDC DDC PROM Emula. Mode YES Options are Dynamic, Static and Passthru. In Dynamic mode, the DDC of the monitor connected to the RX is read and stored on the TX. The CPU is informed of a change in DDC and the monitor is read. This is useful when the CPU can be turned on without a connection to the RX. Static mode is used to maintain the current DDC regardless of monitor changes at the RX. Passthru mode makes the DDC pins look like direct connections between the TX and RX, allowing the computer to talk directly to the monitor. Load Default DDC YES Loads the default EDID table into the TX which allows 1920x1200. This puts the TX into static mode. Load 1080p YES Loads a widescreen version of the EDID table into the TX. Supported resolutions include 1920x1080 and 1280x720. Acquire DDC YES Gets the DDC table of the attached display, stores the information and puts the TX in static mode. Force DDC Mode YES Used to force the DDC of a monitor to appear as either digital or analog. Since the Velocity products can convert between analog and digital, sometimes the DDC has to be modified to match the method of connecting the TX to CPU. VelocityKVM, Rev F 26 November 2011

27 TRANSMITTER Velocity 5 Video Front Panel Menu Display Modifiable Description * Video VGA Connected NO An indication of whether VGA video is input to the Vis TX Resolution input NO Active pixels x active lines vertical rate Hor. Freq NO Horizontal frequency Auto Phase YES Automatically adjust the Sampling Phase to the best setting PLL Total YES The total pixel count in one line. Consists of Horizontal active pixels + Horizontal blanking pixels HSOUT Width YES Horizontal sync (Hsync) of video, measured in pixels DE Start YES Horizontal back porch (Hpb) of video, measured in pixels DE Width YES Total active pixels in one line Line Start YES Vertical back porch (Vbp) + Vertical sync (Vsync) of video, measured in lines Line Width YES The number of visible lines in one frame Hsync Period NO Used to determine analog video horizontal frequency. Use the following formula to calculate the frequency: (25x10E6 x 16) / Hsync Period = Horizontal Frequency Vsync Period NO Total lines in one frame of video. Total lines = active lines + blanking lines ISL Sync Status NO For use by Thinklogical support. Measures sync selection and sync polarity ISL Sync Activity NO For use by Thinklogical support. Measures sync activity Video 1 cnt. NO Internal use only. Video 2 cnt. NO Internal use only. Video 3 cnt. NO Internal use only. Video 4 cnt. NO Internal use only. RECEIVER: *System LS Connected NO Indicates fiber status from TX to RX (0=connected) Tx Ctrl Name TX Only Name entered on TX unit is displayed on RX unit. KM Device NO Revision of the VelocityKVM portion that plugs into CPU. KM Remote Host NO Revision of the VelocityVKM Host on the RX unit. KM Local Host NO Revision of the VelocityVKM Host on the TX unit. TX Control NO Revision of the TX unit laser and front panel control. RX Control NO Revision of the RX unit laser and front panel control. FPGA Version NO Revision of the FPGA used for video generation. Serial Number NO 2 digits each for DDMMYY and 2 or 3 unique digits Debug Values YES Factory Use. Aud/USB Reset En YES Enable/disable USB 1.1. Reset for lost Tx/Rx link. SFP Loss of Signal NO Indicates loss of SFP signal. (1=not connected) Temp in Celsius NO IN=PCB temp (max=70) EX=FPGA temp (max=85) KMASS Card ID NO 0E=original Video Card ID NO 08=single, 09=dual head, 0A=dual link, 0B=RGB USB 2.0 Card ID NO 08=original, 09=SoDimm VelocityKVM, Rev F 27 November 2011

28 Display Modifiable Description *PS2 Devices PS2 KB Scan NO Value of 1, 2 or 3 for the scan code. 0= not connected to the CPU. PS2 Mouse Mode NO Value of 0, 3 or 4 for the mode. 255= mouse not properly connected to the CPU. *USB Country Code USB Country NO The country code of the USB KB that the unit reports itself as being. This is the last USB KB country applied to the remote host. Most hardware is not localized and thus this value would be zero (0), which is displayed as Not Supported USB Device Enum NO A bit pattern that indicates which ports have been enumerated at the Velocity device side. The bits are laid out as Bit0=KB, Bit1=MS, Bit2=TBLT, Bit3=DWNLD, Bit4=Daughter Card_KB, Bit5=Daughter_MS, Bit6=Daughter_TBLT. *DDC DDC PROM Emula. Mode YES Options are Dynamic, Static and Passthru. In Dynamic mode, the DDC of the monitor connected to the RX is read and stored on the TX. The CPU is informed of a change in DDC and the monitor is read. This is useful when the CPU can be turned on without a connection to the RX. Static mode is used to maintain the current DDC regardless of monitor changes at the RX. Passthru mode makes the DDC pins look like direct connections between the TX and RX, allowing the computer to talk directly to the monitor. Load Default DDC YES Loads the default DDC stored in the application which allows 1024x768. This puts the TX into static mode. Load 1080p YES Loads a widescreen version of the EDID table into the RX. Supported resolutions include 1920x1080 and 1280x720. Acquire DDC YES Gets the DDC table of the unit attached, stores the information and puts the TX in static mode. Force DDC Mode YES Used to force the DDC of a monitor to appear either digital or analog. Since VelocityKVM products can convert between analog and digital, sometimes the DDC has to be modified to match the method of connecting the TX to CPU. *Video Video Tx 1 cnt. NO Video IN 1 pixel sample clock (TX) Video Rx 1 cnt. NO Video IN 1 pixel sample clock (RX) Video Tx 2 cnt. NO Video IN 2 pixel sample clock (TX) Video Rx 2 cnt. NO Video IN 2 pixel sample clock (RX) TX 1 Stream Info NO Video Channel 1 ID TX 2 Stream Info NO Video Channel 2 ID PropConst YES Factory default setting for debug IntegConst YES Factory default setting for debug VelocityKVM, Rev F 28 November 2011

29 Saving Changes Save analog video configurations so that following power up, the device can recall custom video settings. Thinklogical Velocity Tx VXX.XX Using the down arrow, scroll down to *System as shown below. *System Using the right arrow, scroll right until Store Values is displayed as shown below, then press enter. Store Values Yes/No.= No Using the up arrow or down arrow scroll until Yes appears as shown below. Then press enter. Store Values Yes/No.= Yes Using the right arrow or left arrow scroll until you return to the *System menu option. Using up arrow or down arrow, scroll until you get to the Thinklogical screen as shown below. Thinklogical Velocity Tx VXX.XX VelocityKVM, Rev F 29 November 2011

30 Restoring Factory Defaults Load factory default video configurations. Thinklogical Velocity Tx VXX.XX Using the down arrow, scroll down to *System as shown below. *System Using the right arrow button, scroll right until Load Defaults is displayed as shown below. Then press enter. Load Defaults Yes/No= No Using the up arrow or down arrow, scroll until Yes appears as shown below. Then press enter. Load Defaults Yes/No= Yes Follow the steps below to save your changes: Using the down arrow, scroll down to *System. Using the right arrow, scroll right until Store Values is displayed. Then press enter. Using the up or down arrow, scroll until Yes appears. Then press enter. Using the right or left arrow, scroll to return to the *System menu option. Using up or down arrow, scroll until you get to the Thinklogical screen. VelocityKVM, Rev F 30 November 2011

31 Naming the Transmitter Unit Modify the name of the unit through the Transmitter. The name entered on the Transmitter will display on the Receiver unit. Thinklogical Velocity Tx VXX.XX Using the arrow down button, scroll down to *System as shown below. *System Using the right arrow, scroll right until Tx Ctrl is displayed as shown below. Then press enter. Tx Ctrl Name= TxUnit01 Using the right or left arrow, scroll until the blinking cursor is under the letter/number you want to change. Tx Ctrl Name= TxUnit01 Using the up or down arrow, scroll (holding down the up or down arrow will scroll faster) until you find the appropriate letter/number. Then press enter. Tx Ctrl Name= TxUnit11 VelocityKVM, Rev F 31 November 2011

32 Using the right or left arrow, scroll to return to the *System menu option. *System Follow the steps below to save your changes: Using the down arrow, scroll down to *System. Using the right arrow, scroll right until Store Values is displayed. Then press enter. Using the up or down arrow, scroll until Yes appears. Then press enter. Using the right or left arrow, scroll to return to the *System menu option. Using up or down arrow, scroll until you get to the Thinklogical screen. VelocityKVM, Rev F 32 November 2011

33 Regulatory & Safety Compliance Safety Requirements Symbols Found on Our Product Markings and labels on the product follow industry-standard conventions. Regulatory markings found on the products comply with domestic and many international requirements. Regulatory Compliance The Thinklogical VelocityKVM Extender products are designed and made in the U.S.A. VelocityKVM Extender products have been tested by a certified testing laboratory and found to be compliant with the following standards (both domestic USA and many international locations): North America Safety ANSI/UL : 1 st Edition (2003) CAN/CSA C22.2 No LASER Safety CDRH 21CFR Class 1 LASER Product Electromagnetic Interference FCC CFR47, Part 15, Class A Industry Canada ICES-003 Issue 2, Revision 1 Australia & New Zealand This is a Class A product. In a domestic environment this product may cause radio interference, in which case the user may be required to take adequate measures. European Union Declaration of Conformity Manufacturer s Name & Address: Thinklogical LLC 100 Washington Street Milford, Connecticut USA Telephone These products comply with the requirements of the Low Voltage Directive 72/23/EEC and the EMC Directive 89/336/EEC. VelocityKVM, Rev F 33 November 2011

34 Standards with Which Our Products Comply Safety CENELEC EN , 1 st Edition (2001) LASER Safety IEC60825:2001 Parts 1 and 2 Class 1 LASER Product Electromagnetic Emissions EN55022: 1994 (IEC/CSPIR22: 1993) EN /A14: 2000 EN : 1994 Electromagnetic Immunity EN55024: 1998 Information Technology Equipment-Immunity Characteristics EN : 1995 Electro-Static Discharge Test EN : 1996 Radiated Immunity Field Test EN : 1995 Electrical Fast Transient Test EN : 1995 Power Supply Surge Test EN : 1996 Conducted Immunity Test EN : 1993 Magnetic Field Test EN : 1994 Voltage Dips & Interrupts Test Supplementary Information The following statements may be appropriate for certain geographical regions and might not apply to your location. This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe A respecte toutes les exigencies du Règlement sur le matérial brouilleur du Canada. Warning! This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take corrective measures. VelocityKVM, Rev F 34 November 2011

35 Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications in which case the user may be required to take adequate corrective measures at their own expense. Note: This Class A digital apparatus complies with Canadian ICES-003 and has been verified as being compliant within the Class A limits of the FCC Radio Frequency Device Rules (FCC Title 47, Part 15, Subpart B CLASS A), measured to CISPR 22: 1993 limits and methods of measurement of Radio Disturbance Characteristics of Information Technology Equipment. Note: The user may notice degraded audio performance in the presence of electromagnetic fields. Note: If using a keyboard that is noise susceptible, a ferrite ring on the keyboard cable may be needed to comply with Immunity Requirements Product Serial Number VelocityKVM products have a unique serial number, imprinted on an adhesive label that is fixed to the bottom of the chassis. The serial number includes a date-code. The format for the date-code is 2 digits for the week (01-52) and 2 digits for the year (00-99), plus two or three digits/characters for a unique unit number. This serial number is also found on the original shipping carton. Connection to Our Products Connections and installation hardware for our products use industry-standard devices and methods. All wiring connections to the customer equipment are designed to minimize proprietary or customized connectors and cabling. Power connections are made with regionally appropriate power cords and approved methods. VelocityKVM, Rev F 35 November 2011

36 How to Contact Us Customer Support Thinklogical is an engineering company and you will receive the assistance you require directly from our most knowledgeable engineers. We believe that the first line of support is the design engineer that developed each particular product. Therefore your needs will be handled promptly by our in-house engineers who are most familiar with your products. Website Check out our website for current product offerings, support information and general information about all of the products we offer. Our internet website offers product information on all current systems, including technical specification sheets and installation guides (for viewing online or for download), product diagrams showing physical connections and other information you might need. Internet: Note: Most online documents are stored as Adobe Acrobat PDF files. If you do not have the Adobe Acrobat reader needed to view PDF files, visit for a download. Thinklogical is staffed Monday through Friday from 8:30am to 5:00pm, Eastern Time Zone. We will do our best to respond to your s promptly. Please use one of the following addresses for your particular needs: info@thinklogical.com Information on Thinklogical and our products. sales@thinklogical.com Sales Department - orders, questions or issues. support@thinklogical.com Product support, technical issues or questions, product repairs and request for Return Authorization. Telephone Telephone Sales: Contact our expert sales staff in Milford, CT at or if in the continental USA, you may use our toll-free number We are here Monday through Friday from 8:30am to 5:00pm, Eastern Time Zone. Ask for your representative s direct dial phone number when you call. VelocityKVM, Rev F 36 November 2011

37 Telephone Product Support: Contact Product Support in Milford, CT at The support lines are manned Monday through Friday, 8:30am to 5:00pm, Eastern Time Zone. International Sales: Please contact our US sales staff in Milford, CT at We are here Monday through Friday, 8:30am to 5:00pm, Eastern Time Zone (same as New York City). If leaving a voice message please let us know the best time to return your call so we may reach you at your convenience. Our switchboard attendant will direct your call during regular business hours. We have an automated attendant answering our main telephone switchboard after regular business hours and holidays. You can leave a voice message for an individual at any time. Our Sales Representatives have direct numbers to speed up your next call to us. Fax Our company facsimile number is Please indicate the nature of the fax on your cover sheet and provide return contact information. Product Support Thinklogical s support personnel are available Monday through Friday from 8:30am to 5:00pm, Eastern Time Zone. If your application requires assistance at some time outside of our normal business hours, please contact us beforehand and we will do our best to make arrangements to help you with your Thinklogical products. Limited Warranty Information Thinklogical, LLC ( Thinklogical ) warrants this product against defects in materials and workmanship for a period of one (1) year from the date of delivery (ordinary wear and tear excluded). This limited warranty does not cover defects resulting from (i) use of the product other than as described in the applicable documentation for the product; (ii) modifications to or repairs of the product that are made by any party other than Thinklogical or a party acting on Thinklogical s behalf, or (iii) combination of the product with third party products that is not consented to by Thinklogical. Occurrences of events described in (i) (iii) shall void the foregoing warranty. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Except for the express warranty set forth above, to the fullest extent permitted under applicable law, Thinklogical, LLC and its suppliers disclaim any and all other warranties, express and implied, including without limitation the implied warranties of merchantability, fitness for a particular purpose, title and non-infringement. If the defective product is returned to the authorized dealer within one (1) year of the delivery date, repair or replacement of the product will be made. Repairs may be made with refurbished parts. If repair or replacement is not possible, Thinklogical may keep the defective product and refund the amount that you paid for the defective product. These are Thinklogical s sole obligations, and your exclusive remedies, for a breach of the limited warranty set forth above. To return a defective product, contact the Thinklogical authorized dealer from whom you purchased the product. Do not return a product directly to Thinklogical without prior authorization from your dealer. If you have received prior authorization from your dealer and are returning a product directly to Thinklogical: VelocityKVM, Rev F 37 November 2011

38 1. You may contact your Sales Representative directly or call Customer Support at or (toll free). 2. Describe the defect with the product and Customer Support will issue a Return Merchandise Authorization Number (RMA#). 3. Pack the product in all of its original packing, if possible, and write the RMA number on the box. 4. Return the product to: Thinklogical, LLC Attn: RMA# [Insert the RMA# issued to you, by Thinklogical, here.] 100 Washington Street Milford, CT USA Our Address If you have any issue with a product, have product questions or need technical assistance with your Thinklogical system, please call us at (USA only) or and let us help. If you d like to write us, our mailing address is: Thinklogical, LLC 100 Washington Street Milford, CT USA VelocityKVM, Rev F 38 November 2011

39 Appendix A In the following part number examples, the inclusion of the USB 2.0 and HID option is shown. (This is the W immediately following the VEL-). There is also a USB 2.0 and USB 1.1 that is a U option. For the FireWire option, this will be an F and for the HID option, it will be a leading H. Thinklogical's Full Line of Velocitykvm and Video Multi-Mode Fiber Extenders Part Number VEL-W00M04-LCRX VEL-W00M04-LCTX VEL-W00M04-SCRX VEL-W00M04-SCTX VEL-W00M04-STRX VEL-W00M04-STTX Description VelocityKVM-4 Multi-Mode Fiber Extenders Velocity KVM Extender Receiver, Single Head Single Link DVI, HID, USB 2.0, KMAS, Multi-mode, LC Velocity KVM Extender Transmitter, Single Head Single Link DVI, HID, USB 2.0, KMAS, Multi-mode, LC Velocity KVM Extender Receiver, Single Head Single Link DVI, HID, USB 2.0, KMAS, Multi-mode, SC Velocity KVM Extender Transmitter, Single Head Single Link DVI, HID, USB 2.0, KMAS, Multi-mode, SC Velocity KVM Extender Receiver, Single Head Single Link DVI, HID, USB 2.0, KMAS, Multi-mode, ST Velocity KVM Extender Transmitter, Single Head Single Link DVI, HID, USB 2.0, KMAS, Multi-mode, ST VelocityKVM-5 Multi-Mode Fiber Extenders VEL-W00M05-LCRX VEL-W00M05-LCTX VEL-W00M05-SCRX VEL-W00M05-SCTX VEL-W00M05-STRX VEL-W00M05-STTX VEL-W00M08-LCRX VEL-W00M08-LCTX VEL-W00M08-SCRX VEL-W00M08-SCTX VEL-W00M08-STRX VEL-W00M08-STTX Part Number Velocity KVM Extender Rx, Single Head Dual Link DVI/RGB, HID, USB 2.0, KMAS, Multi-mode, LC Velocity KVM Extender Tx, Single Head Dual Link DVI/RGB, HID, USB2.0, KMAS, Multi-mode, LC Velocity KVM Extender Rx, Single Head Dual Link DVI/RGB, HID, USB 2.0, KMAS, Multi-mode, SC Velocity KVM Extender Tx, Single Head Dual Link DVI/RGB, HID, USB2.0, KMAS, Multi-mode, SC Velocity KVM Extender Rx, Single Head Dual Link DVI/RGB, HID, USB 2.0, KMAS, Multi-mode, ST Velocity KVM Extender Tx, Single Head Dual Link DVI/RGB, HID, USB2.0, KMAS, Multi-mode, ST VelocityKVM-8 Multi-Mode Fiber Extenders Velocity KVM Extender Receiver, Single Head Dual Link DVI, HID, USB 2.0, KMAS, Multi-mode, LC Velocity KVM Extender Transmitter, Single Head Dual Link DVI, HID, USB 2.0, KMAS, Multi-mode, LC Velocity KVM Extender Receiver, Single Head Dual Link DVI, HID, USB 2.0, KMAS, Multi-mode, SC Velocity KVM Extender Transmitter, Single Head Dual Link DVI, HID, USB 2.0, KMAS, Multi-mode, SC Velocity KVM Extender Receiver, Single Head Dual Link DVI, HID, USB 2.0, KMAS, Multi-mode, ST Velocity KVM Extender Transmitter, Single Head Dual Link DVI, HID, USB 2.0, KMAS, Multi-mode, ST VelocityKVM-24 Multi-Mode Fiber Extenders VelocityKVM, Rev F 39 November 2011

40 VEL-W00M24-LCRX VEL-W00M24-LCTX VEL-W00M24-SCRX VEL-W00M24-SCTX VEL-W00M24-STRX VEL-W00M24-STTX VEL-W00M28-LCRX VEL-W00M28-LCTX VEL-W00M28-SCRX VEL-W00M28-SCTX VEL-W00M28-STRX VEL-W00M28-STTX VEL-W00M34-LCRX VEL-W00M34-LCTX VEL-W00M34-SCRX VEL-W00M34-SCTX VEL-W00M34-STRX VEL-W00M34-STTX VEL-W00M35-LCRX VEL-W00M35-LCTX VEL-W00M35-SCRX VEL-W00M35-SCTX VEL-W00M35-STRX VEL-W00M35-STTX Part Number VEL-W00M38-LCRX VEL-W00M38-LCTX VEL-W00M38-SCRX VEL-W00M38-SCTX Velocity KVM Extender Receiver, Dual Head Single Link DVI, HID, USB 2.0, KMAS, Multi-mode, LC Velocity KVM Extender Transmitter, Dual Head Single Link DVI, HID, USB 2.0, KMAS, Multi-mode, LC Velocity KVM Extender Receiver, Dual Head Single Link DVI, HID, USB 2.0, KMAS, Multi-mode, SC Velocity KVM Extender Transmitter, Dual Head Single Link DVI, HID, USB 2.0, KMAS, Multi-mode, SC Velocity KVM Extender Receiver, Dual Head Single Link DVI, HID, USB 2.0, KMAS, Multi-mode, ST Velocity KVM Extender Transmitter, Dual Head Single Link DVI, HID, USB 2.0, KMAS, Multi-mode, ST VelocityKVM-28 Multi-Mode Fiber Extenders Velocity KVM Extender Receiver, Dual Link, Single Link DVI, HID, USB 2.0, KMAS, Multi-mode, LC Velocity KVM Extender Transmitter, Dual Link, Single Link DVI, HID, USB 2.0, KMAS, Multi-mode, LC Velocity KVM Extender Receiver, Dual Link, Single Link DVI, HID, USB 2.0, KMAS, Multi-mode, SC Velocity KVM Extender Transmitter, Dual Link, Single Link DVI, HID, USB 2.0, KMAS, Multi-mode, SC Velocity KVM Extender Receiver, Dual Link, Single Link DVI, HID, USB 2.0, KMAS, Multi-mode, ST Velocity KVM Extender Transmitter, Dual Link, Single Link DVI, HID, USB 2.0, KMAS, Multi-mode, ST VelocityKVM-34 Multi-Mode Fiber Extenders Velocity KVM Extender Receiver, DVI Four Display, HID, USB 2.0, KMAS, Multi-mode, LC Velocity KVM Extender Transmitter, DVI Four Display, HID, USB 2.0, KMAS, Multi-mode, LC Velocity KVM Extender Receiver, DVI Four Display, HID, USB 2.0, KMAS, Multi-mode, SC Velocity KVM Extender Transmitter, DVI Four Display, HID, USB 2.0, KMAS, Multi-mode, SC Velocity KVM Extender Receiver, DVI Four Display, HID, USB 2.0, KMAS, Multi-mode, ST Velocity KVM Extender Transmitter, DVI Four Display, HID, USB 2.0, KMAS, Multi-mode, ST VelocityKVM-35 Multi-Mode Fiber Extenders Velocity KVM Extender Receiver, DVI Three Display, HID, USB 2.0, KMAS, Multi-mode, LC Velocity KVM Extender Transmitter, DVI Three Display, HID, USB 2.0, KMAS, Multi-mode, LC Velocity KVM Extender Receiver, DVI Three Display, HID, USB 2.0, KMAS, Multi-mode, SC Velocity KVM Extender Transmitter, DVI Three Display, HID, USB 2.0, KMAS, Multi-mode, SC Velocity KVM Extender Receiver, DVI Three Display, HID, USB 2.0, KMAS, Multi-mode, ST Velocity KVM Extender Transmitter, DVI Three Display, HID, USB 2.0, KMAS, Multi-mode, ST VelocityKVM-38 Multi-Mode Fiber Extenders Velocity KVM Extender Receiver, DVI two Dual-link Display, HID, USB 2.0, KMAS, Multi-mode, LC Velocity KVM Extender Transmitter, DVI two Dual-link Display, HID, USB 2.0, KMAS, Multi-mode, LC Velocity KVM Extender Receiver, DVI two Dual-link Display, HID, USB 2.0, KMAS, Multi-mode, SC Velocity KVM Extender Transmitter, DVI two Dual-link Display, HID, USB 2.0, KMAS, Multi-mode, SC VelocityKVM, Rev F 40 November 2011

41 VEL-W00M38-STRX VEL-W00M38-STTX Velocity KVM Extender Receiver, DVI two Dual-link Display, HID, USB 2.0, KMAS, Multi-mode, ST Velocity KVM Extender Transmitter, DVI two Dual-link Display, HID, USB 2.0, KMAS, Multi-mode, ST Thinklogical's Full Line of Velocitykvm and Video Single-Mode Fiber Extenders Part Number Description VelocityKVM-4 Single-Mode Fiber Extenders VEL-W00S04-SCRX Velocity KVM Extender Rx, Single Head Single Link DVI, HID, USB 2.0, KMAS, Single-mode, SC/APC VEL-W00S04-SCTX Velocity KVM Extender Tx, Single Head Single Link DVI, HID, USB 2.0, KMAS, Single-mode, SC/APC VelocityKVM-5 Single-Mode Fiber Extenders VEL-W00S05-SCRX Velocity KVM Extender Rx, Single Head Dual Link DVI/RGB, HID, USB 2.0, KMAS, Single-mode, SC/APC VEL-W00S05-SCTX Velocity KVM Extender Tx, Single Head Dual Link DVI/RGB, HID, USB2.0, KMAS, Single-mode, SC/APC VelocityKVM-8 Single-Mode Fiber Extenders VEL-W00S08-SCRX Velocity KVM Extender Rx, Single Head Dual Link DVI, HID, USB 2.0, KMAS, Single-mode, SC/APC VEL-W00S08-SCTX Velocity KVM Extender Tx, Single Head Dual Link DVI, HID, USB 2.0, KMAS, Single-mode, SC/APC VelocityKVM-24 Single-Mode Fiber Extenders VEL-W00S24-SCRX Velocity KVM Extender Rx, Dual Head Single Link DVI, HID, USB 2.0, KMAS, Single-mode, SC/APC VEL-W00S24-SCTX Velocity KVM Extender Tx, Dual Head Single Link DVI, HID, USB 2.0, KMAS, Single-mode, SC/APC Part Number VelocityKVM-28 Single-Mode Fiber Extenders VEL-W00S28-SCRX Velocity KVM Extender Rx, Dual Link, Single Link DVI, HID, USB 2.0, KMAS, Single-mode, SC/APC VEL-W00S28-SCTX Velocity KVM Extender Tx, Dual Link, Single Link DVI, HID, USB 2.0, KMAS, Single-mode, SC/APC Velocity KVM-34 Single-Mode Fiber Extenders VEL-W00S34-SCRX Velocity KVM Extender Rx, 4 Display DVI, HID, USB 2.0, KMAS, Single-mode, SC/APC VEL-W00S34-SCTX Velocity KVM Extender Tx, 4 Display DVI, HID, USB 2.0, KMAS, Single-mode, SC/APC VelocityKVM-35 Single-Mode Fiber Extenders VEL-W00S35-SCRX Velocity KVM Extender Rx, 3 Display DVI, HID, USB 2.0, KMAS, Single-mode, SC/APC VEL-W00S35-SCTX Velocity KVM Extender Tx, 3 Display DVI, HID, USB 2.0, KMAS, Single-mode, SC/APC VelocityKVM-38 Single-Mode Fiber Extenders VEL-W00S38-SCRX Velocity KVM Extender Rx, Two Dual-link DVI Display, HID, USB 2.0, KMAS, Single-mode, SC/APC VEL-W00S38-SCTX Velocity KVM Extender Tx, Two Dual-link DVI Display, HID, USB 2.0, KMAS, Single-mode, SC/APC VelocityKVM, Rev F 41 November 2011

42 Part Number Reference- Velocity KVM Extenders VEL-XXXXXX-XXXX VEL = Velocity 000= USB D= USB 1.1 with Separate Data Path 0R0= USB 1.1 with Redundant Fiber Path E00= Firewire with USB 2.0 E0D= Firewire with USB 2.0 with Separate Data Path F00= Firewire with USB 1.1 H00= HID HOD= HID with Separate Data Path HR0= HID, Redundant N00= Network N0D= Network with Separate Data Path SP0= StudioPro U00= USB 2.0 U0D= USB 2.0 with Separate Data Path UR0= USB 2.0 with Redundant Fiber Path W00= HID with USB 2.0 W0D= HID with USB 2.0 with Separate Data Path TX= Transmitter RX= Receiver ST Connector SC Connector LC Connector NK Connector 04= 1 SL DVI + KMASS 05= 1 SL RGB/DVI + KMASS 08= 1 DL DVI + KMASS 24= 2 SL DVI + KMASS 28= 1 SL DVI +1 DL DVI + KMASS 34= 4 SL DVI + KMASS 35= 3 SL DVI + KMASS 38= 2 DL DVI + KMASS SL= SL DVI (StudioPro Only) DL= DL DVI (StudioPro Only) M= Multi-Mode S=Single-Mode VelocityKVM, Rev F 42 November 2011

43 Appendix B- Quick Start Guides Local DVI OUT CAUTION! Replace with same type and rating fuse. STEREO EMITTER SER IAL PORT USE ONLY WITH 250V FUSE P S 2 PWR FOL Source CPU CP CLINK DVI OUT DVI IN INPUT HID LOCAL FROM CPU V-,0.5A, 50/60 Hz T 2A,250VAC USB 2.0 Option DVI IN Stereo Emitter IN Audio IN Audio OUT PS/2 Keyboard PS/2 Mouse USB HID (Kybd/Mouse) USB 1.1 (Kybd/Mouse) L1 L2 CAUTION! Replace with same type and rating fuse. STEREO EMITTER U P D A T E S LINE OUT FOL SER IAL PORT PWR USE ONLY WITH 250V FUSE P S 2 DVI OUT DDC DVI OUT OUTPUT MIC IN V-,0.5A, 50/60 Hz T 2A,250VAC DVI OUT Stereo 3-D USB 2.0 Option DVI OUT DDC Audio IN/OUT Velocitykvm-4 Multi-Mode Fiber Extension System Single Head, Single Link DVI QUICK START GUIDE L1 L STEP 1: Connect your Multi-Mode Fiber Optic Cables between the Transmitter and Receiver units (up to 1000 meters) as shown. L1: Data Tx to Rx and Video L2: Data Rx to Tx STEP 5: If desired, connect your optional local keyboard & mouse by inserting the PS/2 or USB HID connectors into the VelocityKVM Transmitter s local devices receptacles and connect the optional local DVI display to the Transmitter s DVI OUT Port. Ensure all system functions are operating properly. LINE IN MIC OUT USB HID or PS2 Keyboard/Mouse 5 USB 1.1 PS/2 or USB connectors USB HID UPDATES DEV HOST CTRL STEP 2: Ensure that the POWER ON/OFF switch is in the OFF position (0) on both the Tx and Rx units. Connect the supplied AC Power Cords to both units and plug each into a standard AC supply. Turn both switches ON (1). 2 STEP 4: Connect the DVI and KVM cables between the Source CPU and the VelocityKVM Transmitter using the cables supplied in KIT R. Ensure the CPU is turned ON. USB 2.0 USB HID USB 1.1 USB HID or PS2 Keyboard/Mouse HOST CTRL VELOCITY-4_Manual_QSG 3 STEP 3: Connect the destination DVI and KVM devices to the VelocityKVM Receiver using standard cables. Ensure the devices are turned ON. A.B.1 VelocityKVM-4 Quick Start Guide VelocityKVM, Rev F 43 November 2011

44 A.B.2 VelocityKVM-5 Quick Start Guide VelocityKVM, Rev F 44 November 2011

45 A.B.3 VelocityKVM-8 Quick Start Guide VelocityKVM, Rev F 45 November 2011