C60. Multilin BREAKER PROTECTION SYSTEM. Breaker Monitoring and Control for Substation and Industrial Automation KEY BENEFITS APPLICATIONS FEATURES

Transcription

1 ultilin C60 BREAKER PROTECTON SYSTE Breaker onitoring and Control for Substation and ndustrial Automation KEY BENETS g imagination Complete breaker control, protection, monitoring and integration in a single platform Advanced automation capabilities for providing customized protection and control solutions odular hardware architecture allows for flexibility in device configurations to cover most breaker applications Three independent fiber or copper Ethernet ports for simultaneous/ dedicated network connections with advanced microsecond time synchronization via LAN with EEE 588 support Reduced wiring through the use of high-speed peer-to-peer communication for accepting trip and close commands from other relays Embedded EC 6850 protocol with no external communications hardware required APPLCATONS Stand-alone breaker monitoring and control ultiple breaker configuration control including breaker-and-ahalf and ring bus EATURES Protection and Control Breaker failure Synchronism check Autoreclose and open pole detector Phase, neutral and auxiliary overvoltage Neutral and auxiliary overvoltage Thermal overload, phase, ground and neutral overcurrent Sensitive directional power Dual breaker control Communication Networking interfaces: up to three Ethernet ports 00b fiber or copper, RS485, RS3, RS4, G.703, C37.94 ultiple protocols: EC 6850, DNP 3.0 and odbus serial/tcp, EEE 588, EC and 03, PRP, SNTP, HTTP, TTP, EGD Direct /O: secure, high-speed exchange of data between URs for direct transfer trip and /O extension applications Embedded managed Ethernet switch with four 00 bit fiber optic ports and copper ports at work Phasor easurement Unit (synchrophasor) according to EEE C37.8 (0) and EC support Simplified system integration with communications supporting serial, Ethernet and multiple protocols ncrease network availability by reducing failover time to zero through EC "PRP" support CyberSentry provides high-end cyber security aligned to industry standards and services (NERC CP, AAA, Radius, RBAC, Syslog) Robust network security enabling Critical nfrastructure Protection through user command logging, and dual permission access control Advanced fault and disturbance recording, including internal relay operating signals thus eliminating the need for external recording devices Complete EC 6850 Process Bus solution provides resource optimization and minimizes total P&C life cycle costs Automatic bus transfer scheme using a single device As part of a distributed bay controller EC 6850 Process Bus nterface Robust communications with up to 8 Hardiber Bricks Redundant architecture for dependability and security onitoring and etering etering: current, voltage, power, energy, frequency P & Class synchrophasors of voltage, current and sequence components: reporting rate to 0 frames/sec Advanced recording capabilities deliver a 04 event recorder, configurable and extended waveform capture and data logger ault Locator Setting for security audit trails for tracking changes to the C60 configuration Enerista T Software Graphical Logic Designer and Logic onitor to simplify designing and testing procedures via Enerista UR Engineer Service and update notification toolset ensures device documents and software are up-to-date via Enerista Launchpad Enerista ntegrator providing easy integration of data in the C60 into new or existing monitoring and control systems

2 Protection and Control The C60 breaker protection system is a substation hardened controller that provides a complete integrated package for the protection, control, and monitoring of circuit breakers. The C60 supports dual-breaker busbar configurations such as breaker-and-a-half or ring bus arrangements. Signals from up to 4 sets of CT s can be brought into the C60 for internal summation, which is advantageous by still having the individual currents available for metering and the additional protection elements that operate on individual currents. The C60 provides fast and deterministic execution of programmable logic and extensive /O options that are necessary for substation automation applications. All of the necessary control logic functions are available for creating automated breaker control schemes, such as the popular maintie-main scheme using a single C60 device. Using high-speed peer-to-peer communications for inter-device messaging, the C60 can also accept breaker opening, closing and lock-out commands from other devices at a fraction of the cost of hardwiring these signals. As part of the UR amily, the C60 provides superior protection and control including: C60 - Protection, etering, onitoring and Control The C60 is the single point for protection, control, metering, and monitoring in one integrated device that can easily be connected directly into DCS or SCADA monitoring and control systems like iewpoint onitoring as shown. Breaker ailure The breaker failure functions included in the C60 are available to detect breaker failure conditions for both single and three-pole tripping schemes. The C60 provides two independent breaker failure functions, and all of the current source inputs, digital inputs and digital outputs need to perform breaker failure functions on dual breaker schemes, such as breaker-and-a-half or ring bus arrangements. Breaker failure initiation and transfer tripping signals can be done using hardwired contacts or through communications (EC 6850 and direct /O). Autorecloser The C60 provides multi-shot autoreclosing on all types of faults for single or three-pole applications with independent dead time for each shot. The protection settings can be changed between shots (typical application being an accelerated zone extension scheme). Autoreclosure can also be dynamically blocked by user-programmable unctional Block Diagram P 5P TRP CLOSE 79 CLOSE TRP 50B 3 59X 7X lexelement T 59N 49 ETERNG Transducer nput 50NB 59P ANS Device Numbers & unctions Device Number unction 5(4) Synchrocheck 7P Phase Undervoltage 7X Auxiliary Undervoltage 3 Directional Power 49 Thermal Overload 50G Ground nstantaneous Overcurrent 50N Neutral nstantaneous Overcurrent 50P Phase nstantaneous Overcurrent 5G Ground Time Overcurrent 5N Neutral Time Overcurrent 5P Phase Time Overcurrent 59N Neutral Overvoltage 59P Phase Overvoltage 59X Auxiliary Overvoltage 79 Autoreclose 50B Breaker ailure 50NB Neutral nstantaneous Breaker ailure 50P 5P 50B 3 50NB 59N 7 5 C60 Breaker Protection System 480

3 logic. our different autoreclose modes are available, enabling users to select the reclosure mode to suit specific applications. The autoreclose modes can be dynamically changed by any internal lexlogic digital operand, allowing flexibility with changing system conditions. lexlogic Designer Synchrocheck The C60 provides four synchrocheck elements that monitor voltage difference, phase angle difference and slip frequency to ensure proper breaker closure as per user requirements. Any of the four synchrocheck elements can be dynamically blocked or unblocked by other elements or user logic, allowing coordination with other C60 protection settings and groups. The C60 provides additional enhancements in synchronizing by checking dead source conditions for synchronism bypass under these conditions. Overcurrent and Thermal Elements Overcurrent protection is delivered through instantaneous and time overcurrent elements available for phase, neutral, ground and sensitive ground protection. ost of the standard protection curves are provided. Thermal overload elements as per the EC 55-8 standard are also available. Sensitive Directional Power Two separate directional power elements are provided to detect reverse and low forward power conditions for use in EEE 547 DG interconnection anti-islanding protection. Breaker Control The C60 allows for control of up to two breakers through commands given to it from either local or remote users. The C60 front panel can have 6 user-configurable pushbuttons that can be used to select and operate the breaker functions. Each button can be customized and labeled for easy operator identification. The C60 can also accept breaker operation commands from remote users through one of the many available communication protocols including odbus, DNP 3.0, EC 6850, and EC EC 6850 Process Bus The EC 6850 Process Bus module is designed to interface with the GE ultilin lexlogic allows for the creation of customized C60 breaker control schemes, including the receipt of trip and close commands from other devices, and the creation of logic to replace the need for external lockout relays. Hardiber System, allowing bi-directional EC 6850 fiber optic communications. The Hardiber System is designed to integrate seamlessly with existing Universal Relay (UR) applications, including protection functions, lexlogic, metering and communications. The GE ultilin Hardiber System offers the following benefits: Communicates using open standard EC 6850 messaging Drastically reduces P&C design, installation and testing labor by eliminating individual copper terminations ntegrates with existing C60 s by replacing traditional CT/T inputs with the EC 6850 Process Bus module Does not introduce new cyber security concerns isit the Hardiber System product page on the GE ultilin web site for more details. Advanced Automation The C60 incorporates advanced automation features including powerful lexlogic programmable logic, communication, and SCADA capabilities that far surpass what is found in the average breaker relay or controller. The C60 integrates seamlessly with other UR relays for complete breaker management including reclosing, load shedding, and synchronism applications. lexlogic lexlogic is the powerful UR-platform programming logic engine that provides the ability to create customized protection and control schemes, minimizing the need and associated costs of auxiliary components and wiring. Using lexlogic, the C60 can be programmed to provide the required logic for performing complete breaker control in schemes that may include simple single breaker management, equipment backup protection as well as sophisticated automatic transfer schemes. Scalable Hardware The C60 is available with a multitude of /O configurations to suit the most demanding application needs. The expandable modular design allows for easy configuration and future upgrades. ultiple CT/T configurations allow for the implementation of many different schemes, including single and dual breaker applications lexible, modular /O covering a broad range of input signals and tripping schemes 48

4 RTDs and DCmA inputs are available to monitor equipment parameters such as temperature and pressure onitoring and etering The C60 includes high accuracy metering and recording for all AC signals. oltage, current, and power metering are built into the relay as a standard feature. Current and voltage parameters are available as total RS magnitude, and as fundamental frequency magnitude and angle. ault and Disturbance Recording The advanced disturbance and event recording features within the C60 can significantly reduce the time needed for postmortem analysis of power system events and the creation of regulatory reports. Recording functions include: Sequence of Event (SOE) - 04 time stamped events Oscillography - 64 digital & up to 40 analog channels - Events up to 45s in length Data Logger and Disturbance Recording - 6 channels up to sample/cycle/ channel ault Reports - Powerful summary report of pre-fault and fault values The very high sampling rate and large amounts of storage space available for data recording in the C60 can eliminate the need for installing costly stand-alone recording equipment. Advanced Device Health Diagnostics The C60 performs comprehensive device health diagnostic tests at startup and continuously during run-time to test its own major functions and critical hardware. These diagnostic tests monitor for conditions that could impact security and availability of protection, and present device status via SCADA communications and front panel display. Providing continuous monitoring and early detection of possible issues help improve system uptime. Comprehensive device health diagnostic performed at startup onitors the CT/T input circuitry to validate the integrity of all signals Cyber Security CyberSentry UR CyberSentry UR enabled UR devices deliver full cyber security features that help customers to comply with NERC CP and NST R 768 cyber security requirements. This software option delivers the following core features: AAA Server Support (Radius/LDAP) Enables integration with centrally managed authentication and accounting of all user activities and uses modern industry best practices and standards that meet and exceed NERC CP requirements for authentication and password management. Role Based Access Control (RBAC) Efficiently administrate users and roles within UR devices. The new and advanced access functions allow users to configure up to five roles for up to eight configurable users with independent passwords. The standard Remote Authentication Dial n User Service (Radius) is used for authentication. Event Recorder (Syslog for SE) Capture all cyber security related events within a SOE element (login, logout, invalid password attempts, remote/local access, Power System Troubleshooting The C60 contains tools that allow for the early detection of impending breaker problems and allow for maintenance to be performed before serious damage occurs. Triggering a waveform on each breaker operation can identify changes in the length of time each part or mechanism in the breaker takes to perform its function. Breaker Latch Release Time: ndicates how long it took for the breaker latch to release from the time the trip coil was energized by the relay. Arc Extinguish Time: ndicates the length of time that was required for the breaker to extinguish the arc and finally clear the fault. Breaker echanism Travel Time: ndicates time interval required for the breaker mechanism to travel to its rest position. 48

5 user in session, settings change, W update, etc), and then serve and classify data by security level using standard Syslog data format. This will enable integration with established SE (Security Event anagement) systems. Communications The C60 provides advanced communications technologies for remote data and engineering access, making it easy and flexible to use and integrate into new and existing infrastructures. Direct support for fiber optic Ethernet provides high-bandwidth communications allowing for low-latency controls and high-speed file transfers of relay fault and event record information. The available three independent Ethernet ports, redundant Ethernet option and the embedded managed Ethernet switch provide the means to create fault tolerant communication architectures in an easy, cost-effective manner without the need for intermediary communication hardware. The C60 supports the most popular industry standard protocols enabling easy, direct integration into DCS and SCADA systems. EC 6850 with support DNP 3.0 Ethernet Global Data (EGD) EC and EC odbus RTU, odbus TCP/P PRP as per EC EEE 588 for time synchronization nteroperability with Embedded EC 6850 Use the C60 with integrated EC 6850 to lower costs associated with breaker protection, control and automation. GE Digital Energy's leadership in EC 6850 comes from thousands of installed devices and follows on extensive development experience with UCA.0. Replace expensive copper wiring between devices with direct transfer of data using GOOSE messaging Configure GE systems based on EC 6850 and also monitor and troubleshoot them in real-time with Enerista iewpoint Engineer ulticast EEE C37.8 synchrophasor data between PU and PDC devices using EC Direct /O essaging Direct /O allows for the sharing of high-speed digital information between multiple UR relays via direct back-to-back connections or multiplexed through a standard DS0 multiplexer channel bank. Regardless of the connection method, direct /O provides continuous realtime channel monitoring that supplies diagnostics information on channel health. Direct /O provides superior relay-to-relay communications that can be used in advanced interlocking, generation rejection and other special protection schemes. Communication with up to 6 UR relays in single or redundant rings rather than strictly limited to simplistic point-to-point configurations between two devices Connect to standard DS0 channel banks through standard RS4, G.703 or EEE C37.94 interfaces or via direct fiber optic connections No external or handheld tester required to provide channel diagnostic information Simplifying ault and Disturbance Analysis The events recorded in multiple GE devices can be collected and merged into a single station-wide SOE record to simplify the tracking of substation operations. 483

6 LAN Redundancy Substation LAN redundancy has been traditionally accomplished by reconfiguring the active network topology in case of failure. Regardless of the type of LAN architecture (tree, mesh, etc), reconfiguring the active LAN requires time to switchover, during which the LAN is unavailable. UR devices deliver redundancy as specified by PRP-EC , which eliminates the dependency on LAN reconfiguration and the associated switchover time. The UR becomes a dual attached node that transmits data packets over both main and redundant networks simultaneously, so in case of failure, one of the data packets will reach the receiving device with no time delay. ulti-language UR devices support multiple languages: English, rench, Russian, Chinese, Turkish and German. These language options are available on the front panel, in the Enerista setup software, and in the product manuals. Easily switch between English and an additional language on the local displays without uploading new firmware. Enerista Software The Enerist suite is an industry-leading set of software programs that simplifies every aspect of using the C60 relay. The Enerista suite provides all the tools to monitor the status of the protected asset, maintain the relay, and integrate information measured by the C60 into DCS or SCADA monitoring systems. Convenient COTRADE and SOE viewers are an integral part of the UR setup software included with every UR relay, to carry out postmortem event analysis to ensure proper protection system operation. Enerista Launchpad Enerista Launchpad is a powerful software package that provides users with all of the setup and support tools needed for configuring and maintaining GE ultilin products. The setup software within Launchpad allows for the configuration of devices in real-time by communicating using serial, Ethernet, or modem connections, or offline by creating setting files to be sent to devices at a later time. ncluded in Launchpad is a document archiving and management system that ensures critical documentation is up-to-date and available when needed. Documents made available include: anuals Application Notes Guideform Specifications Brochures Wiring Diagrams AQ s Service Bulletins iewpoint onitoring iewpoint onitoring is a simple-to-use and full-featured monitoring and data recording software package for small systems. iewpoint onitoring provides a complete H package with the following functionality: Plug-&-Play Device onitoring System Single-Line onitoring & Control Annunciator Alarm Screens Trending Reports Automatic Event Retrieval Automatic Waveform Retrieval iewpoint UR Engineer iewpoint UR Engineer is a set of powerful tools that allows the configuration and testing of GE relays at a system level in an easy-to-use graphical drag-and-drop environment. iewpoint UR Engineer provides the following configuration and commissioning utilities: Graphical Logic Designer Graphical System Designer Graphical Logic onitor Graphical System onitor iewpoint aintenance iewpoint aintenance provides tools that will create reports on the operating status of the relay, simplify the steps to download fault and event data, and reduce the work required for cyber security compliance audits. Tools available in iewpoint aintenance include: Settings Security Audit Report Device Health Report Single-Click ault Data Retrieval Enerista ntegrator Enerista ntegrator is a toolkit that allows seamless integration of GE ultilin devices into new or existing automation systems. ncluded in Enerista ntegrator is: OPC/DDE Server GE ultilin Drivers Automatic Event Retrieval Automatic Waveform Retrieval 48 Configurable LED ndicators User nterface The C60 front panel provides extensive local H capabilities. The local display is used for monitoring, status messaging, fault diagnosis, and device configuration. User-configurable messages that combine text with live data can be displayed when user-defined conditions are met. ulti-language Display English Russian rench Chinese Turkish German User-Programmable Pushbuttons 484

7 485 C60 Breaker Protection System Typical Wiring C60-H00-HCL-8-H6G-8-P6G C60 Power Supply 9 CPU 8 CT/T 6 nputs/ outputs 6 nputs/ outputs 8 CT/T J U X L W K B H T D N G P S R A B C CONNECTON CONNECTON 5 5 RS-3 DB-9 (front) UR COPUTER TXD RXD RXD TXD SGND SGND CONNECTOR PERSONAL COPUTER CONNECTOR TC TC DC inimum PRODED c 4a 8c 8a 3c 5a 5c 7c 6a 7a 6c c X A B C 4c a 4b b a 3a b 3b X A B C A B C G A5 A B5 C5 G5 B C G Ha Hb Hc Hb Hc Ha H4a H4c H3b H3a H4b H3c SURGE H6a H8a H5b H7b H8b H5a H7a H6c H8c H5c H7c H H H3 H4 6G Pa Pb Pc Pb Pc Pa P4a P4c P3b P3a P4b P3c SURGE P6a P8a P5b P7b P8b P5a P7a P6c P8c P5c P7c 3 4 6G CRTCAL ALURE OUTPUT CONTROL POWER H LO LTER SURGE B3a Bb B8a B6b B8b B6a B3b Ba Bb B5b c 4a 8c 8a 3c 5a 5c 7c 6a 7a 6c c X A B C 4c a 4b b a 3a b 3b X A B C A B C G A5 A B5 C5 G5 B C G com 0BaseL 0BaseL 0BaseT Da Da D4b D3a D4a RG-B nput RG-B Output CO RS485 ALTERNATE NORAL Tx Rx Tx Rx BNC BNC ibre Optic * Remote Device Shielded Co-axial Co-axial ultilin

8 Ordering C60 - * ** - H * * - **- H **- **- P ** - U **- W ** or ull Sized Horizontal ount C60 - * ** - * - **- H **- ** #** or Reduced Size ertical ount Base Unit C60 Base Unit CPU E RS485 + RS485 (EC 6850 option not available) J RS485 + multimode ST 00BaseX K RS485 + multimode ST Redundant 00BaseX N RS /00BaseT T RS485 + three multimode SP LC 00BaseX. Req W v7xx or higher U RS485 + two multimode SP LC 00BaseX + one SP RJ45 00BaseT. Req W v7xx or higher RS485 + three SP RJ45 00BaseT. Req W v7xx or higher Software Options 00 No Software Options (see note below) 0 Ethernet Global Data 03 EC Ethernet Global Data 4 x PU 5 EC x PU A0 CyberSentry UR Lvl. Req UR W 7.xx or higher B0 EEE 588. Req UR W 7.xx or higher C0 PRP D0 EEE CyberSentry UR. Req UR W 7.xx or higher ount H Horizontal (9" rack) - Standard A Horizontal (9" rack) - Harsh Chemical Environment Option ertical (3/4 size) - Standard B ertical (3/4 size) - Harsh Chemical Environment Option User nterface ertical ront Panel with English Display Enhanced German ront Panel J Enhanced German ront Panel with User-Programmable Pushbuttons K Enhanced English ront Panel L Enhanced English ront Panel with User-Programmable Pushbuttons Enhanced rench ront Panel N Enhanced rench ront Panel with User-Programmable Pushbuttons Q Enhanced Russian ront Panel T Enhanced Russian ront Panel with User-Programmable Pushbuttons U Enhanced Chinese ront Panel Enhanced Chinese ront Panel with User-Programmable Pushbuttons W Enhanced Turkish ront Panel Y Enhanced Turkish ront Panel with User-Programmable Pushbuttons Power Supply H 5 / 50 AC/DC (see note below) H RH 5/50 AC/DC with redundant 5/50 AC/DC power supply L 4-48 (DC only) CT/T DSP 8L 8L Standard 4CT/4T w/ enhanced diagnostics 8 8 Sensitive Ground 4CT/4T w/ enhanced diagnostics 8N 8N Standard 8CT w/ enhanced diagnostics 8R 8R Sensitive Ground 8CT w/ enhanced diagnostics EC 6850 Process Bus 8 8 Port EC 6850 Process Bus odule Digital /O XX XX XX XX XX No module 4A 4A 4A 4A 4A 4 Solid State (No onitoring) OSET Outputs 4C 4C 4C 4C 4C 4 Solid State (Current w/opt oltage) OSET Outputs 4L 4L 4L 4L 4L 4 orm-a (No onitoring) Latchable Outputs orm-a (No onitoring) Outputs 6C 6C 6C 6C 6C 8 orm-c Outputs 6D 6D 6D 6D 6D 6 Digital nputs 6E 6E 6E 6E 6E 4 orm-c Outputs, 8 Digital nputs ast orm-c Outputs 6K 6K 6K 6K 6K 4 orm-c & 4 ast orm-c Outputs 6L 6L 6L 6L 6L orm-a (Current w/ opt oltage) & orm-c Outputs, 8 Digital nputs orm-a (Current w/ opt oltage) & 4 orm-c Outputs, 4 Digital nputs 6N 6N 6N 6N 6N 4 orm-a (Current w/ opt oltage) Outputs, 8 Digital nputs 6P 6P 6P 6P 6P 6 orm-a (Current w/ opt oltage) Outputs, 4 Digital nputs 6R 6R 6R 6R 6R orm-a (No onitoring) & orm-c Outputs, 8 Digital nputs 6S 6S 6S 6S 6S orm-a (No onitoring) & 4 orm-c Outputs, 4 Digital nputs 6T 6T 6T 6T 6T 4 orm-a (No onitoring) Outputs, 8 Digital nputs 6U 6U 6U 6U 6U 6 orm-a (No onitoring) Outputs, 4 Digital nputs orm-a (Cur w/ opt olt) orm-c Output, Latching Outputs, 8 Digital nputs Transducer /O 5A 5A 5A 5A 5A 4 dcma nputs, 4 dcma Outputs 5C 5C 5C 5C 5C 8 RTD nputs 5D 5D 5D 5D 5D 4 RTD nputs, 4 dcma Outputs 5E 5E 5E 5E 5E 4 dcma nputs, 4 RTD nputs dcma nputs nter-relay Communications B EEE C37.94, 300nm, singlemode, ELED, Channel Channel - EEE C37.94, 80nm, multimode fiber, 64/8 kbps; Channel nm, singlemode, LASER J Channel - EEE C37.94, 80nm, multimode fiber, 64/8 kbps; Channel nm, singlemode, LASER 7A 80 nm, multimode, LED, Channel 7B 300 nm, multimode, LED, Channel 7C 300 nm, singlemode, ELED, Channel 7H 80 nm, multimode, LED, Channels nm, multimode, LED, Channels 7J 300 nm, singlemode, ELED, Channels 7S G.703, Channels 7W RS4, Channels 77 EEE C37.94, 80 nm, multimode, LED, Channel Ordering Note:. To view all the options available for C60, please visit GE s On-Line Store at Redundant power supply only available in horizontal unit. f redundant is chosen, must be same type. aximum per chassis Accessories for the C60 UR Applications Learning CD TRCD-URA-C-S- ultilink Ethernet Switch L400--H-H-A-A-A6- iewpoint Engineer PE- iewpoint aintenance P- iewpoint onitoring EC 6850 P EC is a registered trademark of Commission Electrotechnique nternationale. EEE is a registered trademark of the nstitute of Electrical Electronics Engineers, nc. odbus is a registered trademark of Schneider Automation. NERC is a registered trademark of North American Electric Reliability Council. NST is a registered trademark of the National nstitute of Standards and Technology. GE, the GE monogram, ultilin, lexlogic, Enerista and CyberSentry are trademarks of General Electric Company. GE reserves the right to make changes to specifications of products described at any time without notice and without obligation to notify any person of such changes. Copyright 03, General Electric Company. 486 GEA-654D(E) English 3083