Fiber Optic Installation and User Manual ver.1.0 [to integrate with the user manual of DAS M32/M44]

Size: px

Start display at page:

Download "Fiber Optic Installation and User Manual ver.1.0 [to integrate with the user manual of DAS M32/M44]"

Marvin Hancock
5 years ago
Views:

1 Fiber Optic Installation and User Manual ver.1.0 [to integrate with the user manual of DAS M32/M44] BMW - idrive Professional Navigation CCC (1-2 buttons)

Installation: WARNING: before installing the DAS

To unlock the system use an interface or contact

To install the DAS receiver, refer to the specific

the power supply cable: - RED wire (fig.

The switch (ON/OFF) of the receiver will be

- BLACK wire (fig.2) must be connected to the GND.

Disconnect the original Fiber Optical cable (fig.

2 Installation: WARNING: before installing the DAS tuner verify that the system of the car MUST be professional and not Business. With Business system the TV tuner does not work. To unlock the system use an interface or contact directly an official BMW center. 1. To install the DAS receiver, refer to the specific user manual; Pay attention on the connection of the power supply cable: - RED wire (fig.3) must be DISCONNECTED. The switch (ON/OFF) of the receiver will be controlled by the Fiber-Optic activity Power supply cable - YELLOW wire (fig.1) must be connected to the +12V permanent/battery - BLACK wire (fig.2) must be connected to the GND Disconnect the original Fiber Optical cable (fig.4) from one of the original multimedia accessories inside the car (DVD, GPS, Amplifier, etc ) and match it directly to DAS fiber optic female connector of the harness on equipment (fig.5)

3 3. Match the two other connectors of DAS harness (fig.6) respectively inside the original accessory (fig.7) and the other one inside DAS receiver (fig.8) Connect one of the 3 DAS Video-OUT (fig.8) trough the adapter cables on equipment (fig.9) and the needed accessory with white Fakra connector (DCABMQS-RCA in fig.9.1) with the Video-IN on the CCC Unit (fig.10)

The CCC unit location on dashboard (fig.

10 11 Video-IN Insert the 2 female crimped pins of DAS cable (fig.

the pins in the pin-out position recommended below.

Insert the wire with label - inside the pin 2 (negative signal).

disconnect them and connect to a yellow RCA to video-in 1 on DAS

4 The CCC unit location on dashboard (fig.10) and the rear side (fig.11) Video-IN Insert the 2 female crimped pins of DAS cable (fig.9.1 DCABMQS- RCA) inside the black 12P housing and then in white Fakra cover. If the connectors are already available in the unit, just connect the pins in the pin-out position recommended below. Insert the wire with label + in pin 4 (positive signal). Insert the wire with label - inside the pin 2 (negative signal). If the pin 2 and 4 are already used by the rear camera, disconnect them and connect to a yellow RCA to video-in 1 on DAS receiver. 9.1 To shift automatically the signal from TV to REAR CAMERA, connect the green wire of the power supply cable (refer to the DAS user manual) directly to the rear camera installed inside the vehicle. 4

5 User Manual: Before coding the TV function using an aftermarket OBD interface, please check if the OEM start-up screen (with logo BMW) has a background grey/silver colour (fig.12); if the colour is brown (fig.13) go directly to an official BMW service to upgrade the entertainment software of the car brown colour necessary upgrade the software in a BMW service 5

6 To enter in DAS TV tuner with the idrive select Enterntainment and select TV (like the original TV Tuner). WARNING: For the basic settings such as color, contrast, brightness and format, please refer to the menu of the car and make sure that the format is congruent with the set menu on the DAS. 6

CCC idrive controller With the CCC platform, we can find 2 idrive versions: - Controlled: where idrive rotation is bound, not free; - Free running: where idrive rotation is free in both directions;

seconds till the message Autostore disappears; by this time the idrive is changed in free running Important: the other menu of the car are now not available To return in controlled mode and use the

7 CCC idrive controller With the CCC platform, we can find 2 idrive versions: - Controlled: where idrive rotation is bound, not free; - Free running: where idrive rotation is free in both directions; To use the idrive controlled in free running mode, operate in the following way: Press the idrive after to have selected TV; Then will appear a graphic overlay with Autostore message; Wait 2/3 seconds till the message Autostore disappears; by this time the idrive is changed in free running Important: the other menu of the car are now not available To return in controlled mode and use the other menu of the car, press the idrive again. PUSH CCC idrive controller Right rotation = UP on remote control (dropdown menu) 7 Left rotation = Down on remote control (dropdown menu) Down Joystick Scroll= OK/Menu Right Joystick Scroll= Right arrow on remote Left Joystick Scroll= Left arrow on remote

Remote Control Functions: ON-OFF TURNING ON/OFF UP ARROW MENU

CONFIGURATION MENU/OK FUNCTIONS SET UP TV/AV1/AV2 SELECTION RIGHT

AND SEARCH SYSTEM NUMBER KEYPAD FOR CHANNEL PRE-SELECTION DOWN

8 Remote Control Functions: ON-OFF TURNING ON/OFF UP ARROW MENU NAVIGATION - ZAPPING KEY LEFT ARROW MENU NAVIGATION - ZAPPING KEY CONFIGURATION MENU/OK FUNCTIONS SET UP TV/AV1/AV2 SELECTION RIGHT ARROW MENU NAVIGATION - ZAPPING KEY DAS MENU TV/RADIO SELECTION AND SEARCH SYSTEM NUMBER KEYPAD FOR CHANNEL PRE-SELECTION DOWN ARROW MENU NAVIGATION - ZAPPING KEY VOLUME ADJUSTMENT STEERING WHEEL CONTROL 8

9 Steering Wheel Controls Right side UP ARROW: UP arrow on remote control OK: MENU/OK on remote control DOWN ARROW: DOWN arrow on remote control 9

10 MULTICONN Srl Via Selvetta, Varese Italy Tel Fax

v.logic Intelligent Solution Interface V4-CCC

v.logic Intelligent Solution Interface For the E-series BMW and Mini with navigation system or radio and 6.5 or 8.8 monitor with 10pin BMW LVDS connector Product features Plug and play media-controller