Industrial 2.5 PATA SLC SSD. HERMIT-F Series. Product Specification INDUSTRIAL. APRO Ultra High Random Speed 2.5 PATA SSD (SLC)

Transcription

1 Industrial 2.5 PATA SLC SSD HERMIT-F Series Product Specification INDUSTRIAL APRO Ultra High Random Speed 2.5 PATA SSD (SLC) Version 01V0 Document No. 100-xR2IF-HFTS November 2017 APRO CO., LTD. Phone: Fax:

2 This document is for information use only and is subject to change without prior notice. APRO Co., Ltd. assumes no responsibility for any errors that may appear in this document, nor for incidental or consequential damages resulting from the furnishing, performance or use of this material. No part of this document may be reproduced, transmitted, transcribed, stored in a retrievable manner or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written consent of an officer of APRO Co., Ltd. All parts of the APRO documentation are protected by copyright law and all rights are reserved. APRO and the APRO logo are registered trademarks of APRO Co., Ltd. Product names mentioned herein are for identification purposes only and may be trademarks and/or registered trademarks of their respective companies APRO Corporation. All rights reserved. Revision History Revision Description Date 1.0 Initial release 2017/11/17

3 Contents CONTENTS 1. INTRODUCTION SCOPE SYSTEM FEATURES FLASH MANAGEMENT TECHNOLOGY_STATIC, DYNAMIC, AND GLOBAL WEAR LEVELING PROTECTED AGAINST DATA CORRUPTION AND FAILING DEVICES PRODUCT SPECIFICATIONS SYSTEM ENVIRONMENTAL SPECIFICATIONS SYSTEM POWER REQUIREMENTS SYSTEM PERFORMANCE SYSTEM RELIABILITY PHYSICAL SPECIFICATIONS CONFORMAL COATING INTERFACE DESCRIPTION APRO ULTRA HIGH RANDOM SPEED 2.5 PATA SSD INTERFACE PIN ASSIGNMENTS APPENDIX A: ORDERING INFORMATION PART NUMBER LIST PART NUMBER DECODER: APPENDIX B: LIMITED WARRANTY APRO Ultra High Random Speed 2.5 PATA SSD HERMIT-F Series 2017 APRO Co., Ltd.

4 1. Introduction APRO Ultra High Random Speed 2.5 PATA SSD HERMIT-F Series provides ULTRA HIGH RANDOM SPEED Solid State Drive (SSD) that electrically complies with ATA/ATAPI 7 standard. APRO Ultra High Random Speed 2.5 PATA SSD HERMIT-F Series support UDMA-6 with high random write (4K data size) performance. The main used flash memories are SLC-NAND type flash memory chips. The available disk capacities are 128MB, 256MB, 512MB, 1GB, 2GB, 4GB and 8GB. The operating temperature grade is optional for Standard grade 0 C ~ 70 C and industrial grade -40 C ~ +85 C. The data transfer performance by sequential read is up to 55 MB/sec, and sequential write is up to 36 MB/sec; 4k data random read is up to 10.4MB/sec, and 4k data random write is up to 8.3MB/sec. APRO Ultra High Random Speed 2.5 PATA SSD products provide a high level interface to the host computer. This interface allows a host computer to issue commands to the 2.5 PATA SLC SSD to read or write blocks of memory. Each sector is protected by a flexible 96-Bit/1KB BCH ECC engine. APRO Ultra High Random Speed 2.5 PATA SSD HERMIT-F Series intelligent controller manages interface protocols, data storage and retrieval as well as ECC, defect handling and diagnostics, power management and clock control. Figure 1 shows a block diagram of the used high tech PATA SSD controller. Figure 1: APRO Ultra High Random Speed 2.5 PATA SSD HERMIT-F Series controller block diagram APRO Ultra High Random Speed 2.5 PATA SSD HERMIT-F Series 2017 APRO Co., Ltd.

5 1.1. Scope This document describes features, specifications and installation guide of APRO Ultra High Random Speed 2.5 PATA SSD HERMIT-F Series. The appendix provides order information, warranty policy, RMA/DOA procedure for the most convenient reference System Features SLC-NAND type flash technology Standard 44-Pin PATA (IDE) male connector Extremely Rugged Metal casing to endure harsh environments PIO 3~6, MWDMA 0~4, UDMA 0~6 supported Non-volatile memory and no moving parts SLC Flash SSD standard grade capacity from 128MB up to 8GB Sequential read performance up to 55 MB/sec. Sequential write performance up to 36 MB/sec. 4k data random read performance up to 10.4 MB/sec. (QD32) 4k data random write performance up to 8.3 MB/sec. (QD32) Flexible 96-Bit/1KB BCH ECC engine. +5V ± 10% operation Shock : 0.5ms, 1500 G, 3 axes Vibration : 7 Hz to 2K Hz, 20G, 3 axes Built-in Low Voltage Detector Very high performance, very low power consumption, Low weight, Noiseless Standard grade supports operating temperature 0 C to +70 C, and Industrial Grade supports -40 C to +85 C Certifications and Declarations - Certifications: CE & FCC - Declarations: RoHS2 & REACH 1.3. Flash Management Technology_Static, Dynamic, and Global Wear leveling Dynamic: Blocks with lowest erase count selected for writing from free block list Static: When a block is added to the free list, its erase count is compared to the overall lowest erase count; if the distance is higher than the WL-threshold, data content is swapped (GC) and the block with low erase count moves to the free blocks Global: Both dynamic and static WL is global within ILV channel Done in background, interruptible by host commands APRO Ultra High Random Speed 2.5 PATA SSD HERMIT-F Series 2017 APRO Co., Ltd.

6 1.4. Protected against data corruption and failing devices Sudden Power Fail (SPF) Event Reset of controller and immediate write protection of flash If the last data written is corrupt, controller recovers latest valid entry If a write operation is active at power loss this data might be lost Transaction-oriented logging of mapping changes All mapping information is kept in non-volatile storage MLC-aware Power Fail Management Option: Reliable Write of user data Rigorous Testing to ensure functionality Power Cycling Test Stress Test Regression Test 2. Product Specifications For all the following specifications, values are defined at ambient temperature and nominal supply voltage unless otherwise stated System Environmental Specifications Table 1: Environmental Specification APRO Ultra High Random Speed 2.5 PATA SSD HERMIT-F Series Standard Grade SR2IFxxxG-HFCTC-U Industrial Grade WR2IFxxxG-HFITI-U Temperature Operating: Non-operating: 0ºC ~ +70ºC -20ºC ~ +80ºC -40ºC ~ +85ºC -50ºC ~ +95ºC Humidity Operating & Non-operating: 10% ~ 95% non-condensing Vibration Operating & Non-operating: 7 Hz to 2K Hz, 20G, 3 axes Shock Operating & Non-operating: 0.5ms, 1500 G, 3 axes 2.2. System Power Requirements Table 2: Power Requirement APRO Ultra High Random Speed 2.5 PATA SSD HERMIT-F Series DC Input Voltage (VCC) +5V ± 10% Reading Mode : Writing Mode : Idle Mode : ma (max.) 84.6mA (max.) 10.4 ma (max.) APRO Ultra High Random Speed 2.5 PATA SSD HERMIT-F Series 2017 APRO Co., Ltd.

7 2.3. System Performance Table 3: System Performances Data Transfer Mode supporting Average Access Time PIO 3~6, MWDMA 0~4, UDMA 0~6 supported 0.5 ms (estimated) Capacity 128MB 256MB 512MB 1GB 2GB 4GB 8GB Maximum Performance Sequential Read (MB/s) Sequential Write(MB/s) K Random Read (MB/s) K Random Write(MB/s) Note: (1). All values quoted are typically at 25 and nominal supply voltage. (2). Testing of the 2.5 PATA SLC SSD maximum performance was performed under the following platform: - Computer with AMD processor - Windows 7 Professional operating system 2.4. System Reliability Table 4: System Reliability Wear-leveling Algorithms Bad Blocks Management ECC Technology Global Wear-leveling Supported Flexible 96-Bit/1KB BCH ECC engine Endurance SLC STD. Grade SLC IND. Grade 3 years / Within 60K Erasing Counts 5 years / Within 60K Erasing Counts Capacity TBW(TB) Estimated Life(Year) Write Budget [8,192MB/day] 128MB MB MB GB GB GB GB Note: Total bytes written is based on JEDEC 218 (Solid-State Drive Requirements and Endurance Test Method) 2.5. Physical Specifications Refer to Table 5 and see Figure 3 for 2.5 PATA SLC SSD HERMIT-F Series physical specifications and dimensions APRO Ultra High Random Speed 2.5 PATA SSD HERMIT-F Series 2017 APRO Co., Ltd.

8 Table 5: Physical Specifications of APRO Ultra High Random Speed 2.5 PATA SSD-HERMIT-F Series Length: Width: Thickness: Weight: mm / 3.93 in mm / 2.75 in 8.80 mm / 0.35 in g / 2.47 oz Figure 2: APRO Ultra High Random Speed 2.5 PATA SSD Dimension APRO Ultra High Random Speed 2.5 PATA SSD HERMIT-F Series 2017 APRO Co., Ltd.

9 Conformal coating Conformal coating is a protective, dielectric coating designed to conform to the surface of an assembled printed circuit board. Commonly used conformal coatings include silicone, acrylic, urethane and epoxy. APRO applies only silicone on APRO storages products upon requested especially by customers. The type of silicone coating features good thermal shock resistance due to flexibility. It is also easy to apply and repair. Conformal coating offers protection of circuitry from moisture, fungus, dust and corrosion caused by extreme environments. It also prevents damage from those Flash storages handling during construction, installation and use, and reduces mechanical stress on components and protects from thermal shock. The greatest advantage of conformal coating is to allow greater component density due to increased dielectric strength between conductors. APRO uses MIL-I-46058C silicon conformal coating 3. Interface Description 3.1. APRO Ultra High Random Speed 2.5 PATA SSD interface Pin 1 ~ pin 44 are for IDE interface. Pin A ~ pin D is for Master/Slave selection via physical jumpers. Figure 3 : The connectors of 2.5 PATA SLC SSD APRO Ultra High Random Speed 2.5 PATA SSD HERMIT-F Series 2017 APRO Co., Ltd.

10 3.2. Pin Assignments Signals whose source is the host is designated as inputs while signals that APRO 2.5 PATA SLC Solid State Disk HERMIT-F Series sources are outputs. The pin assignments are listed in below table 7. Table 7 - Pin Assignments Pin Name Descriptions Pin Name Descriptions 01 -RESET Drive Reset 02 GND Ground 03 DD7 Drive data bus bit 7 04 DD8 Drive data bus bit 8 05 DD6 Drive data bus bit 6 06 DD9 Drive data bus bit 9 07 DD5 Drive data bus bit 5 08 DD10 Drive data bus bit DD4 Drive data bus bit 4 10 DD11 Drive data bus bit DD3 Drive data bus bit 3 12 DD12 Drive data bus bit DD2 Drive data bus bit 2 14 DD13 Drive data bus bit DD1 Drive data bus bit 1 16 DD14 Drive data bus bit DD0 Drive data bus bit 0 18 DD15 Drive data bus bit GND Ground 20 KEY No pin 21 DMARQ DMA request 22 GND Ground 23 -DIOW:STOP Drive I/O Write 24 GND Ground 25 DIOR- Drive I/O Read 26 GND Ground 27 IORDY I/O channel ready 28 CSEL Cable select 29 -DMACK DMA acknowledge 30 GND Ground 31 INTRQ Drive interrupt 32 IOIS16 Drive 16 bit I/O 33 DA1 Drive address bus bit PDIAG:-CBLID Passed diagnostics 35 DA0 Drive address bus bit 0 36 DA2 Drive address bus bit CS0 Chip select 0 38 CS1 Chip select DASP Drive active slave present 40 GND Ground 41 VCC +5V supply 42 VCC +5V supply 43 GND Ground 44 NC Reserved for future definition APRO Ultra High Random Speed 2.5 PATA SSD HERMIT-F Series 2017 APRO Co., Ltd.

11 Appendix A: Ordering Information Appendix A: Ordering Information 1. Part Number List APRO Ultra High Random Speed 2.5 PATA SSD HERMIT-F Series Product Picture Grade Standard grade (0ºC ~ 70ºC) Industrial Grade ( -40ºC ~ +85ºC ) 128MB SR2IF128M-HFCTC-U(/C) WR2IF128M-HFITI-U(/C) 256MB SR2IF256M-HFCTC-U(/C) WR2IF256M-HFITI-U(/C) 512MB SR2IF512M-HFCTC-U(/C) WR2IF512M-HFITI-U(/C) 1GB SR2IF001G-HFCTC-U(/C) WR2IF001G-HFITI-U(/C) 2GB SR2IF002G-HFCTC-U(/C) WR2IF002G-HFITI-U(/C) 4GB SR2IF004G-HFCTC-U(/C) WR2IF004G-HFITI-U(/C) 8GB SR2IF008G-HFCTC-U(/C) WR2IF008G-HFITI-U(/C) 2. Part Number Decoder: X1 X2 X3 X4 X5 X6 X7 X8 X9-X11 X12 X13 X14 X15-X17-C X1 : Grade S: Standard Grade operating temp. 0º C ~ 70 º C W: Industrial Temp Grade- operating temp. -40º C ~ +85 º C X2 : The material of case R : 2.5 Rugged Metal Casing X3 X4 X5 : Product category 2IF : 2.5 PATA SSD X6 X7 X8 X9 : Capacity 128M: 128MB 001G: 1GB 256M: 256MB 002G: 2GB 512M: 512MB 004G: 4GB X11 : Controller H : Hyperstone (HERMIT Series) 008G: 8GB X12 : Controller version A, B, C.. X13 : Controller Grade C : Commercial grade I : Industrial grade X14 : Flash IC T : Toshiba SLC-NAND Flash IC X15 : Flash IC grade / Type C : Commercial grade I : Industrial grade X17 : Data Transfer Rate U: Defaulted as UDMA-6 mode / Fixed disk type P: PIO 3-6 mode / Fixed disk type A: Auto detect data transfer mode / Fixed disk type C : Reserved for specific requirement C : Conformal-coating APRO Ultra High Random Speed 2.5 PATA SSD HERMIT-F Series 2017 APRO Co., Ltd.

12 Appendix B: Limited Warranty Appendix B: Limited Warranty APRO warrants your Rugged Metal 2.5 PATA SLC SSD against defects in material and workmanship for the life of the drive. The warranty is void in the case of misuse, accident, alteration, improper installation, misapplication or the result of unauthorized service or repair. The implied warranties of merchantability and fitness for a particular purpose, and all other warranties, expressed or implied, except as set forth in this warranty, shall not apply to the products delivered. In no event shall APRO be liable for any lost profits, lost savings or other incidental or consequential damages arising out of the use of, or inability to use, this product. BEFORE RETURNING PRODUCT, A RETURN MATERIAL AUTHORIZATION (RMA) MUST BE OBTAINED FROM APRO. Product shall be returned to APRO with shipping prepaid. If the product fails to conform based on customers purchasing orders, APRO will reimburse customers for the transportation charges incurred. WARRANTY PERIOD: SLC ( Standard grade ) SLC ( Industrial grade ) 3 years / Within 60K Erasing Counts 5 years / Within 60K Erasing Counts The warranty period is able to extend. Please contact APRO and/or Your APRO distributors for more information APRO Ultra High Random Speed 2.5 PATA SSD HERMIT-F Series 2017 APRO Co., Ltd.