Titans series INDUSTRIAL Rugged Metal 1.8 & 2.5 IDE Flash Disk

Transcription

1 Preliminary spec. sheet ( V2.1) Compatibility: Supported O.S.: Certification: 1-5

2 Operating temperature supports optionally Standard grade 0 C ~ 70 C and Industrial grade -40 C ~ 85 C Features: SLC-NAND type flash technology 1.8 & 2.5 IDE drive form-factor Extremely rugged metal casing to endure harsh environments Capacity from 32MB up to 8GB Compatible with ATA/ATAPI-5 standard Data transfer support PIO 0~4 and UDMA 0~4 Master / Slave selectable Performance up to 25.9MB/sec Specifications: Compatibility Flash technology Form-factor Master / slave setting Host interface ATAPI-5 and True IDE mode NAND type SLC flash based Rugged Metal 1.8 & 2.5 IDE hard disk drive form-factor By jumper Standard 44-pin IDE male connector Performance Data transfer mode Data transfer rate PIO-4 mode or UDMA-4 mode (Default setting) 66.6MB/sec under UDMA-4 mode 16.6MB/sec under PIO-4 mode Sequential read Sequential write Average access time 25.9 MB/sec (Max. /with dual flash / 100MB file test) 11.9 MB/sec (Max. /with dual flash / 100MB file test) 0.7ms (estimated) Environmental specification Operating temperature Non-operating temperature Humidity Acoustic noise Vibration Shock Altitude Standard grade 0 C ~ 70 C / Industrial grade -40 C ~ 85 C Standard grade -20 C ~ 80 C / Industrial grade -50 C ~ 95 C 10% ~ 95% non-condensing 0dB 15G compliance to MIL-STD-810F 1,500G compliance to MIL-STD-810F 70,000 feet 2-5

3 Power consumption Power requirement Reading mode Writing mode Sleeping mode +5V + 10% 190.0mA(Max.) 200.0mA(Max.) 117.5mA(Max.) Reliability Wear-leveling MTBF ECC Endurance Dynamic wear-leveling algorithms > 1,000,000 hours Enhanced management 4-bits per 512bytes block > 2,000,000 cycles logically contributed by dynamic wear-leveling and advanced bad sector management algorithms Data reliability Data retention < 1 non-recoverable error in bits read 10 years Physical specification Weight (max.) 1.8 =59.4g / 2.10 oz. 2.5 =110g / 3.88 oz Dimension(W x L x H) 1.8 =69.85 x x 9.50 (mm) 2.5 = x x 9.50 (mm) Conformal coating Option for special request Warranty Standard grade Industrial grade 3 years 5 years 3-5

4 Titans series Operating temperature supports optionally Standard grade 0 C ~ 70 C and Industrial grade -40 C ~ 85 C Part number list 1.8 rugged metal casing Product picture Capacity 0 C~ 70 C -40 C~ 85 C 32MB SR8IF032M-SACSC-U WR8IF032M-SAISI-U 64MB SR8IF064M-SACSC-U WR8IF064M-SAISI-U 128MB SR8IF128M-SACSC-U WR8IF128M-SAISI-U 256MB SR8IF256M-SACSC-U WR8IF256M-SAISI-U 512MB SR8IF512M-SACSC-U WR8IF512M-SAISI-U 1GB SR8IF001G-SACSC-U WR8IF001G-SAISI-U 2GB SR8IF002G-SACSC-U WR8IF002G-SAISI-U 4GB SR8IF004G-SACSC-U WR8IF004G-SAISI-U 8GB SR8IF008G-SACSC-U WR8IF008G-SAISI-U Part number list 2.5 rugged metal casing Product picture Capacity 0 C~ 70 C -40 C~ 85 C 32MB SR2IF032M-SACSC-U WR2IF032M-SAISI-U 64MB SR2IF064M-SACSC-U WR2IF064M-SAISI-U 128MB SR2IF128M-SACSC-U WR2IF128M-SAISI-U 256MB SR2IF256M-SACSC-U WR2IF256M-SAISI-U 512MB SR2IF512M-SACSC-U WR2IF512M-SAISI-U 1GB SR2IF001G-SACSC-U WR2IF001G-SAISI-U 2GB SR2IF002G-SACSC-U WR2IF002G-SAISI-U 4GB SR2IF004G-SACSC-U WR2IF004G-SAISI-U 8GB SR2IF008G-SACSC-U WR2IF008G-SAISI-U Remarks: The optional data-transfer modes and IDE interface is always Fixed Disk mode: 1. P: optional as PIO-4 mode / Fixed disk type 2. U: defaulted as UDMA-4 mode / Fixed disk type 4-5

5 Part number decoder : X1 X2 X3 X4 X5 X6 X7 X8 X9-X11 X12 X13 X14 X15-Z1/C X1 : Grade S : Standard grade operating temp. 0º C ~ 70 º C W : Industrial grade operating temp. -40º C ~ 85 º C X13 : Controller grade C : Commercial grade I : Industrial grade X2 : The material of case R : Rugged metal casing X14 : Flash IC S : Samsung SLC-NAND flash IC X3 X4 X5 : Product category 8IF : 1.8 IDE flash disk 2IF : 2.5 IDE flash disk X15 : Flash IC grade / Type C : Commercial grade I : Industrial grade X6 X7 X8 X9 : Capacity 032M: 32MB 001G: 1GB 064M: 64MB 002G: 2GB 128M: 128MB 004G: 4GB 256M: 256MB 008G: 8GB 512M: 512MB Z1 : Data transfer rate IDE interface is always Fixed disk mode P: optional as PIO-4 mode / Fixed disk type U: defaulted as UDMA-4 mode / Fixed disk type C : Reserved for specific requirement C : Conformal-coating X11 : Controller S : 3S 88x3 A5 (Titans series) X12 : Controller version A,B,C.. 5-5