Add Smarts to Your Sensor. Phone: Fax: Web: -

Transcription

1 Add Smarts to Your Sensor Phone: Fax: Web: info@clrwtr.com

2 Add Smarts to Your Sensor makes your sensor or switch Smart by adding functionality to your signal via a simple, able Plug and Work solution. Add functions such as timing, counting, speed monitoring or signal inversion by simply plugging the into your sensor or switch. Programming is done via a simple on the existing pin # of your existing Mx (eurofast ) connector. The works with not only TURCK sensors, but with -wire DC sensors from many different manufacturers. For connection to sensors using M8x (picofast ), or 7/8-6UN (minifast ) connectors, adaptor cables are available. s may be combined in series to provide multiple functions, such as a speed monitor with a time delay. Features: Add function to existing installations. Solve control problems quickly in the field. Simple plug-in installation uses industry standard Mx -pin connectors (eurofast). Programmed through Pin. ED aids programming. All styles are 00 ma short-circuit-proof, noise immune switching amplifiers. Phone: Fax: Web: info@clrwtr.com

3 Table of Contents Part Number Function Page SPC-AP6X Pulse or interval counters SPC-AN6X Also used for: - N.C./N.O. converter - 00 ma switching amplifier SPF-AP6X Over or under speed monitors SPF-AN6X Also used for: - 00 ma switching amplifier SPN-AP6-ARN6X - PNP to NPN converter SPN-AN6-ARP6X - NPN to PNP converter Also used for: - N.C./N.O. converter - 00 ma switching amplifier SPT-AP6X On-delay or off-delay timer SPT-AN6X Also used for: - Pulse stretching - 00 ma switching amplifier VB-SP Molded pushbutton programmer... with connectors Phone: Fax: Web: info@clrwtr.com

4 SPC-AP6X / SPC-AN6X Programmable pulse or interval counter Direct adaptation between sensor and connecting cable Counting of pulses or intervals Simple setting by external - No additional wiring required Counting range from 0 to 6555 Switching amplifier up to 00 ma N.C./N.O. inverter The SPC is a freely programmable counter for the direct adaptation to sensors with a standardized Mx connection. The SPC is available in versions: PNP - PNP SPC-AP6X (for use with PNP sensors) NPN - NPN SPC-AN6X (for use with NPN sensors) Connection: The is very easy to connect; it is plugged onto the Mx connector of a sensor and the connecting cable is connected to the other side of the. The sensor configuration has to meet the standards ( (BN) (BU) (BK) ). ogic Output Setting: The setting of the preset number is made by using the signals " " and " ". If for example, pulses have to be counted, the setting can be made as follows (operating voltage being switched on):. Connect with.. Actuate the sensor times (= pulses) - The recognizes automatically pulses at the " ".. Disconnect from READY. After this setting, the of the is activated every fourth pulse. The setting is maintained when the sensor is switched off. pulse counter interval counter operating voltage operation as pulse counter operating voltage operation as interval counter = or active; = or inactive When switching on the operating voltage, the counting procedure is reset. The initial state of the preset number is (pulse counter). Phone: Fax: Web: info@clrwtr.com

5 Technical Data Operating Voltage 0-0 VDC, residual ripple of max. 0% Own Current Consumption: <0 ma Resistance: >0 kω Max. Frequency: 0 kz Min. Response Time: 0. ms Max. Output Current: 00 ma short-circuit proof Ambient Temperature Range: 0 to +60 C (+ to +0 F) Storage Temperature Range: -0 to +60 C (- to +0 F) Display: Red ED ousing Material: Plastic PBTP/PA Protection Standard: IP 67 Dimensions Inches[mm]: See diagram Connection : -pin socket Mx Connection Output: -pin connector Mx Weight: 5 g Preset to factory setting pulse counter t>0s preset done or t>0s preset done Wiring Diagrams SPC-AP6X SPC-AN6X PNP NPN Application Examples:. Gearwheel/Divider: On a gearwheel with 00 teeth, one pulse per rotation is to be measured. a) A suitable sensor with standardized Mx connection is mounted in a way that each tooth is safely recognized. b) A SPC is connected between sensor and sensor connecting cable. c) The preset number 00 is taught into the, connect " " with, turn round the gearwheel exactly one time. d) Disconnect " " from. READY At the of the, one pulse per rotation is measured.. Counting parts: Bulk material is filled into cartons by means of a conveyor belt. The task is to specify the exact number of parts required to fill up the carton. a) A suitable sensor with standardized Mx connection is mounted in a way that all parts are safely recognized. b) A SPC is connected between sensor and sensor connecting cable. c) A " " stays connected to until the desired number of parts has passed the sensor (=unit the carton is full ). d) Disconnect " " from. READY At the of the, one pulse is measured when the preset quantity of parts has been recorded; the carton is full.. Switching amplifier: Most sensors have a maximum current of 00 ma to 00 ma. By using a, the maximum current can be increased to 00 ma. a) A SPC is connected between sensor and sensor connecting cable. b) The " " stays connected to until the sensor has been actuated once (preset number ). c) Disconnect " " from. READY At the of the every pulse is measured, the can be charged with 00 ma.. N.C./N.O. inverter: the as interval counter "". An N.C. signal will be inverted into a N.O. signal and reverse. Phone: Fax: Web: info@clrwtr.com

6 SPF-AP6X / SPF-AN6X Programmable over or under speed monitor Direct adaptation between sensor and connecting cable able speed limit Simple setting by external - No additional wiring required Frequency range 0.05 z - kz Output load up to 00 ma The SPF is a frequency threshold module for the direct adaptation to sensors with a standard Mx connection. The SPF is available in versions: PNP - PNP SPF-AP6X (for use with PNP sensors) NPN - NPN SPF-AN6X (for use with NPN sensors) Connection: The is very easy to connect; it is plugged onto the Mx connector of a sensor and the connecting cable is connected to the other side of the. The sensor configuration has to meet the standards ( (BN) (BU) (BK) ). ogic Output Function: The SPF observes the frequency of the signal at the pin " ". The is activated if the setup frequency falls below approximately 5%. Setting for under speed monitoring:. Set sensor up to sense object with SPF connected. Make sure sensor is sensing properly and is switching.. Move object or set rotation to nominal speed.. Connect +voltage to " " and then disconnect (turn off) voltage. (Pulse to, > full cycle of senses object - e.g. > full revolution). Done, if speed or frequency drops by 5% or 95% of nominal speed, then is activated. Setting for over speed monitoring: (Note: over speed will be inverted. i.e. activated for normal speed & off for over speed.). Set sensor up to sense object with SPF connected. Make sure sensor is sensing properly and is switching.. Move object to set rotation to 06% plus X% over speed allowance of nominal speed.. Connect+voltage to " " and then disconnect (turn off) voltage. (Pulse to, > full cycle of senses object - e.g. > full revolution).. Done. If speed or frequency goes above setpoint, then goes off. Phone: Fax: Web: info@clrwtr.com

7 Technical Data Operating Voltage: 0-0 VDC, residual ripple of max. 0% Own Current Consumption: <0 ma Resistance: >0 kω Max. Frequency: 0 kz Min. Response Time: 0. ms Max. Output Current: 00 ma short-circuit proof Ambient Temperature Range: 0 to +60 C (+ to +0 F) Storage Temperature Range: -0 to +60 C (- to +0 F) Display: Red ED ousing Material: Plastic PBTP/PA Protection Standard: IP 67 Dimensions Inches[mm]: See diagram Connection : -pin socket Mx Connection Output: -pin connector Mx Weight: 5 g SPF-AP6X SPF-AN6X PNP NPN Applications Examples:. Jam detection. RPM Observation. Conveyor built back detection. Cooling fan motion control Phone: Fax: Web: info@clrwtr.com

8 SPN-AP6-ARN6X / SPN-AN6-ARP6X PNP/NPN or NPN/PNP converter, adjustable N.O./N.C. inverter Direct adaptation between sensor and connecting cable N.C./N.O. function adjustable Simple setting via external - No additional wiring required Switching frequency up to 0 kz Switching amplifier up to 00 ma The SPN is a switching channel convertor for the direct adaptation to sensors with a standard Mx connection. The SPN is available in versions: PNP - NPN SPN-AP6-ARN6X (for the conversion of PNP sensors to NPN ) NPN - NPN SPN-AN6-ARP6X (for the conversion of NPN sensors to PNP ) Connection: The is very easy to connect: it is plugged onto the Mx connector of a sensor and the connecting cable is connected to the other side of the. The sensor configuration has to meet the standards ( (BN) (BU) (BK) ). ogic Output Function: The SPN-AP6-ARN6X converts a PNP signal into a NPN signal. The SPN-AN6-ARP6X converts a NPN signal into a PNP signal. Additionally the signal can be inverted (N.C./N.O. function). Setting: The setting of the inverting function is made by means of the signals " " and " " Example:. Setting the into the inverting mode: a) activate sensor ( is on) b) connect and and disconnect (pulse or signal to ). READY. Setting the into the non-inverting mode (factory setting) a) inactivate Sensor ( is off) b) connect and and disconnect (pulse or signal to ). READY This setting is maintained when the sensor is off. Phone: Fax: Web: info@clrwtr.com

9 Technical Data Operating Voltage: 0-0 VDC, residual ripple of max. 0% Own Current Consumption: <0 ma Resistance: >0 kω Max. Frequency: 0 kz Min. Response Time: 0. ms Max. Output Current: 00 ma short-circuit proof Ambient Temperature Range: 0 to +60 C (+ to +0 F) Storage Temperature Range: -0 to +60 C (- to +0 F) Display: Red ED ousing Material: Plastic PBTP/PA Protection Standard: IP 67 Dimensions Inches[mm]: See diagram Connection : -pin socket Mx Connection Output: -pin connector Mx Weight: 5 g = / active = / inactive SPN-AP6-ARN6X SPN-AN6-ARP6X PNP NPN Function Setting PNP / NPN converter SPN-AP6-ARN6X Factory setting NPN / PNP converter SPN-AN6-ARP6X Factory setting PNP / NPN converter and N.C. / N.O. inverter NPN/ PNP converter and N.C. / N.O inverter SPN-AP6-ARN6X SPN-AN6-ARP6X Setup: N.O. N.C. Setup: N.O. N.C. Phone: Fax: Web: info@clrwtr.com

10 SPT-AP6X / SPT-AN6X Programmable timer for on-delay time or off-delay time Direct adaptation between sensor and connecting cable able as on-delay time or off-delay time Simple setting by external - No additional wiring required Time range between and 6555 ms Switching amplifier up to 00 ma Can be used as pulse stretcher The SPT is a freely programmable timer for the direct adaptation to sensors with a standardized Mx connection. The SPT is available in versions: PNP - PNP SPT-AP6X (for use with PNP sensors) NPN - NPN SPT-AN6X (for use with NPN sensors) Connection: The is very easy to connect: it is plugged onto the Mx connector of a sensor and the connecting cable is connected to the other side of the. The sensor configuration has to meet the standards ( (BN) (BU) (BK) ). ogic Setting: The setting of the delay time is made by means of the signals " " and " ". A delay time of seconds for example can be set as follows (the operating voltage being switched on):. Connect with. Actuate sensor for seconds. Disconnect from. READY After this setting the has a slow operation lasting seconds. This setting is maintained when the sensor is switched off. Output ing of an on-delay stored time for on-delay OR ing of an off-delay time stored time for off-delay OR operation with on-delay time stored time for off-delay operation with off-delay time When switching on the operating voltage, the timer is reset. The initial state of the preset time is 00 ms off-delay. = / active = / inactive Phone: Fax: Web: info@clrwtr.com

11 Technical Data Operating Voltage: 0-0 VDC, residual ripple of max. 0% Own Current Consumption: <0 mα Resistance: >0 kω Max. Frequency: 0 kz Min. Response Time: 0. ms Max. Output Current: 00 ma short-circuit proof Ambient Temperature Range: 0 to +60 C (+ to +0 F) Storage Temperature Range: -0 to +60 C (- to +0 F) Display: Red ED ousing Material: Plastic PBTP/PA Protection Standard: IP 67 Dimensions Inches[mm]: See diagram Connection : -pin socket Mx Connection Output: -pin connector Mx Weight: 5 g To preset to factory setting 00 ms off-delay t>0s preset done or t>0s preset done SPT-AP6X SPT-AN6X PNP NPN Phone: Fax: Web: info@clrwtr.com

12 Programing Push Button VB-SP Dimensions Pinouts Wiring Diagram Female Male -pin -pin Phone: Fax: Web: info@clrwtr.com