Automated Tuner System Power Distribution Hub

Transcription

1 User Guide Automated Tuner System Power Distribution Hub Model MT1020B MT (Rev B) 12/11

2

3 User Guide Automated Tuner System Power Distribution Hub Model MT1020B 2900 Inland Empire Boulevard Ontario, California USA Phone: (909) Facsimile: (909) maurymw.com MT (Rev B) 12/11 Copyright 2011 Maury Microwave Corporation. All rights reserved.

4

5 Warranty Maury Microwave hardware products are warranted against defects in materials and workmanship for a period of one year from date of shipment. During the warranty period, Maury Microwave will, at its option, either repair or replace products which prove to be defective. Maury Microwave software products are warranted against defects in material and workmanship of the media on which the product is supplied for a period of ninety (90) days from date of shipment. Maury also warrants that the product shall operate substantially in accordance with published specifications during the same warranty period. During the warranty period, Maury Microwave will, at its option, either repair or replace products which prove to be defective. Maury does not warrant that the operation of the product shall be uninterrupted or error-free. For warranty service or repair, all products must be returned to Maury Microwave and must be issued a return authorization number by Maury prior to shipment. Buyer shall prepay shipping charges to Maury. Obligation is limited to the original Buyer. Limitation of Warranty The foregoing warranty shall not apply to defects resulting from improper or inadequate maintenance by the Buyer, unauthorized modification or misuse, operation outside of the environmental specifications for the product, or wear resulting from normal use. No other warranty is expressed or implied. Maury Microwave specifically disclaims the implied warranties of merchantability and fitness for a particular purpose. The remedies provided herein are the Buyer s sole and exclusive remedies. Maury Microwave shall not be liable for any direct, indirect, special, incidental, or consequential damages whatsoever (including, without limitation, damages for loss of business profits, business interruption, loss of business information, or any other financial loss) arising out of the Buyer s use of or inability to use the product, even if Maury or an authorized Maury dealer has been advised of the possibility of such damages.

6

7 Contents General Information... 1 MT1020B Automated Tuner System Power Distribution Hub... 1 Specifications... 1 Accessories Supplied... 1 Installation... 3 Power Requirements... 3 Ground Requirements... 3 Operational Temperature and Humidity... 3 Connecting the Devices... 3 Operation... 4 Connectors, Controls and Indicators... 4 Appendix... 5 Shipping Package... 5 Data Sheet Resources... 6 Attachment (located behind Appendix) Form No. 278A-12, Declaration of Conformity MT (Rev B) 12/11 i

8 Tables Table 1. Safety Symbol Definitions...2 Figures Figure 1. Power Entry Module with Fuse Holder...3 Figure 2. Front Panel...4 Figure 3. Rear Panel...4 Figure A 1. Packaging Kit...5 ii MT (Rev B) 12/11

9 General Information MT1020B Automated Tuner System Power Distribution Hub The MT1020B Automated Tuner System Power Distribution Hub is designed to provide power and interface control for the Maury USB series of automated mechanical tuners. As many as four units may be controlled through this device. Connection to the host computer is made via a standard USB interface. Specifications USB Interface... USB 1.1 and USB 2.0 compatible Power Requirements to to 63 Hz, 3 Amps Mains supply voltage fluctuations not exceeding ±10% of the nominal voltage. Transient over voltages according to over voltage category II Output Power Amps Amps USB Power ma per port Environmental... Indoor use only Relative humidity, 90% non-condensing Altitude up to 2000 meters Pollution degree 2 Accessories Supplied Qty Part No. Description F Spare fuse (5x20 mm, 3.1 A, slow-blow) C-722 USB cable assembly C-082 Power cord for 115 VAC (USA) or 499-C-469 Power cord for 230 VAC (Europe, CE certified) or 499-C-718 Power cord (China, CCC certified) MT (Rev B) 12/11 1

10 Table 1. Safety Symbol Definitions 2 MT (Rev B) 12/11

11 Installation Power Requirements The model MT1020B power distribution hub contains an internal universal switching supply which requires input power of single phase 100 to 264 VAC at 47 to 63 Hz. The unit contains a four port USB 2.0 hub and a power entry module consisting of a power cord receptacle and fuse holder (see Figure 1). The fuse holder contains a 5x20 mm, 250 VAC, 3.15 A, slow-blow fuse. Ground Requirements Figure 1. Power Entry Module with Fuse Holder To minimize shock hazard, the instrument chassis must be connected to an electrical protective earth ground. The instrument must be connected to the AC mains through a grounded power cable, with the ground wire firmly connected to an electrical ground at the power outlet. Any interruption of the protective (grounding) conductor or disconnection of the protective earth ground will cause a potential shock hazard that could result in personal injury. Operational Temperature and Humidity The MT1020B ATS Power Distribution Hub is designed to operate within the specified performance limits over a temperature range extending from 0 to 50 C (-32 to 122 F) and operate at a maximum (non-condensing) relative humidity of 90% (measured at the fan intake). The fan located on the rear panel assembly cools the instrument by drawing air through the bottom of the instrument case, and exhausting air through the fan opening on the rear panel. Operating the instrument outside the temperature range for extended periods will result in degradation of electrical performance and eventual malfunction. NOTE: Because the MT1020B is fan cooled, it must be installed in a location that allows sufficient (nonrestricted) space below the instrument case for adequate circulation of air. Connecting the Devices The MT1020B Power Distribution Hub is designed to interface with all Maury USB controlled automated mechanical tuners. The cable assembly required to interface with each tuner is provided with the instrument when shipped from the factory. MT (Rev B) 12/11 3

12 Operation WARNING: Always set the MT1020B power switch to the OFF position before installing or removing the combination USB/Power cable assembly to prevent possible damage to the instrument. Set the power switch to the OFF position. Inspect each connector on the tuner, controller and cable assembly to ensure that all connections are clean and undamaged. Align the cable connectors with the tuner and controller connectors and attach. Verify that all connectors are fully engaged before continuing. Install a USB cable assembly between the host computer and the MT1020B Power Distribution Hub. Set the MT1020B power switch to the ON position. To be fully functional, the Power Distribution Hub requires at least one attached USB instrument.. The 4 port USB hub is a standard USB 2.0 hub assembly and will be detected by the computer s Windows operating system. Operation of the USB tuners will be controlled using Maury ATS software version 4.00 or later. No software is required for operation of the MT1020B Power Distribution Hub itself. Connectors, Controls and Indicators Figures 2 and Figure 3 identify the front and rear panel connectors, controls and indicators Figure 2. Front Panel 1. Line power switch 2. Power ON indicator 3. Power and USB connectors Figure 3. Rear Panel 4. AC power entry module 5. Fuse holder (part of power entry module) 6. USB input connector 4 MT (Rev B) 12/11

13 Appendix Shipping Package If it becomes necessary to return the MT1020B ATS Power Distribution Hub to the factory for warranty, repair or maintenance, it is important to protect the unit during transit. To insure this, use of the original packaging materials is suggested. If you do not have the original packaging materials, contact your Maury representative or the factory and a packaging kit will be provided. The instructions provided below will properly prepare the unit for return to the factory. Package the MT1020B ATS Power Distribution Hub using the original carton and foam pads supplied with the unit as shown in Figure A1. Seal carton seams using minimum 2 inch (5 cm) wide adhesive tape. After the unit is packaged into the primary carton and sealed, then package this carton inside a larger carton, properly dunnaged, to prevent shipping damage. Figure A 1. Packaging Kit MT (Rev B) 12/11 5

14 Data Sheet Resources 4T-068 Automated Tuner System Power Distribution Hubs 4T-050F Automated Tuner System 4T-056 Automated Tuners (0.25 to 8 GHz) 4T-072 7mm Automated Tuners (0.8 to 18 GHz) 4T mm Automated Tuners (8.0 to 50 GHz) 4T-074 Millimeter-Wave Automated Tuners (33 to 110 GHz) 4T-076 Automated Sliding Shorts (0.4 to 18 GHz) 6 MT (Rev B) 12/11

15 Contacts Corporate Maury Microwave Corporation 2900 Inland Empire Boulevard Ontario, California United States of America Tel Fax Sales Tel Fax Customer Support Tel Fax Web Site Web Resources Visit our web site for additional product information and literature. Maury Calibration Kits Maury Precision Coaxial and Waveguide-to-Coaxial Adapters Maury Applications Notes Library & Technical Articles Archive Maury Sales Representative Finder