PATA EDOM. Datasheet EDM6D-HR/ EDM6D-HL SA6XXXXRE- FXXXXXXX

Transcription

1 PATA EDOM EDM6D-HR/ EDM6D-HL SA6XXXXRE- FXXXXXXX ACPi Digital Co., Ltd. TEL: FAX: Address: 11F.-3, No.186, Jian 1st Rd., Zhonghe Dist., New Taipei City 235, Taiwan (R.O.C.) 1

2 Table of Contents 1.1 INTRODUCTION GENERAL DESCRIPTION FEATURES SPECIFICATIONS BLOCK DIAGRAM PIN SIGNAL DEFINITION 6 2. GENERAL PRODUCT SPECIFICATIONS INTERFACE 7 3. PHYSICAL CHARACTERISTICS MECHANICAL 8 4. ENVIRONMENTAL SPECIFICATION TEMPERATURE VIBRATION SHOCK REGULATIONS ORDERING INFORMATION CONTACT INFORMATION 12 2

3 1. Introduction 1.1 General Description The Horizontal PATA DOM in a IDE-PATA-44pin interface Disk On Module that feature a flash disk controller chip and NAND type flash memory devices. The EDM6C-Hx is available in 128MB to 16GB capacities in PATA DOM Horizontal type. The drives operate in 5-volts power supply and support ATA PIO mode 6, MDMA mode 4, UDMA mode 4 data transfer. The Disk On Module is geared specifically to the industrial market for use in such products as ATM, factory automation machines, POS terminals, measuring products, ticket-vending machines, parking systems and other industrial product that require high tolerance to environmental condition. 1.2 Features Memory Capacities (SLC): 128MB 256MB 512 MB 1GB 2GB 4GB 8GB Horizontal left or right 44PIN connector High performance Dual Mode Sequential Read: Up to 38.8 MB/sec Sequential Write: Up to 27.8 MB/sec Single Mode Sequential Read: Up to 19.8 MB/sec Sequential Write: Up to 13.8 MB/sec Low Power consumption Supply Voltage:5.0v ± 5 % Typical read:max mA Typical write:max mA Typical idle:1.59ma Highly reliable Mean time to failure (MTTF) :2,000,000 hours, based on Part Stress Analysis Data reliability:built-in ECC function 3

4 Operating shock:1,500g, 0.5msec half sine Operating vibration:2.17g, 7-500Hz Operating Temperature Commercial: -0 C to + 70 C 1.3 Specifications Form Facto:44pin Horizontal PATA DOM no housing Density:128MB up to 16GB Dimension:48mm x 30mm x 5.4mm Interface:Compatible with devices that support the ATA-6 Attachment (with Ultra DMA 4 support) for Disk Drives Standard. Connector:IDE PATA 44 pins Power Supply:5V ± 5 % Package:none OS Support:All 4

5 1.4 Block Diagram 5

6 1.5 Pin Signal Definition Pin Name Description Pin Name Description 1 RESET Host to device reset 2 GND Power GND 3 DATA7 Data Bus bit 7 4 DATA8 Data Bus bit 8 5 DATA6 Data Bus bit 6 6 DATA9 Data Bus bit 9 7 DATA5 Data Bus bit 5 8 DATA10 Data Bus bit 10 9 DATA4 Data Bus bit 4 10 DATA11 Data Bus bit DATA3 Data Bus bit 3 12 DATA12 Data Bus bit DATA2 Data Bus bit 2 14 DATA13 Data Bus bit DATA1 Data Bus bit 1 16 DATA14 Data Bus bit DATA0 Data Bus bit 0 18 DATA15 Data Bus bit GND Power GND 20 KEY PIN For protect pin 21 NC No connect 22 GND Power GND 23 IOW Host I/O write 24 GND Power GND 25 IOR Host I/O read 26 GND Power GND 27 IORDY Host I/O ready 28 NC No connect 29 NC No connect 30 GND Power GND 31 IRQ Host interrupt request 32 IOCS16 I/O chip select 16 bits 33 A1 Device addressing bit 1 34 PDIAG Pass diagnostics 35 A0 Device addressing bit 0 36 A2 Device addressing bit 2 37 CS0 Host chip select bit 0 38 CS1 Host chip select bit 1 39 DASP During the reset protocol 40 GND Power GND 41 VCC POWER +5V 42 VCC POWER +5V 43 GND Power GND 44 NC No connect 6

7 2. General Product Specifications 2.1 Interface The PATA DOM interface compiles with the following standards: PIO mode 4 MDMA 2 UDMA 4 The PATA DOM supports Ultra DMA-4 66MB/sec interface rate. 2.2 Wear-leveling Global Wear-Leveling 2.3 Humidity Operating Humidity (30ºC Max. Wet Bulb Temp): 10% to 95% Non-Operating Humidity (30ºC Max. Wet Bulb Temp): 10% to 95% (with no condensation relative humidity) 2.4 Read and Program/Erase Cycle Program/Erase: 2,000,000 cycles with 2% of device capacity data size (max.) 7

8 3. Physical Characteristics 3.1 Mechanical Parameter Width Length Height Specifications 32.6mm ± 0.2mm 48mm ± 0.2mm 13.4mm ± 0.15mm 8

9 4. ATA Command Set No COMMAND Code FR SC SN CY DH LBA 1 Check Power Mode E5h or 98h D - 2 Erase Sector(s) C0h - Y Y Y Y Y 3 Execute Drive Diagnostic 90h D - 4 Flush Cache E7h D - 5 Format Track 50h - Y - Y Y Y 6 Identify Device ECh D - 7 Identify Device DMA EEh D - 8 Idle E3h or 97h - Y - - D - 9 Idle Immediate E1h or 95h D - 10 Initialize Drive Parameters 91h - Y - - Y - 11 Media Lock DEh D - 12 Media Unlock DFh D - 13 NOP 00h D - 14 Read Buffer E4h D - 15 Read DMA C8h - Y Y Y Y Y 16 Read Long Sector 22h or 23h - - Y Y Y Y 17 Read Multiple C4h - Y Y Y Y Y 18 Read Native Max Address F8h D - 19 Read Sector(s) 20h or 21h - Y Y Y Y Y 20 Read Verify Sector(s) 40h or 41h - Y Y Y Y Y 21 Recalibrate 1Xh D - 22 Request Sense 03h D - 23 Seek 7Xh - - Y Y Y Y 24 Set Features EFh Y D - 25 Set Max Address F9h - Y Y Y Y Y 26 Set Multiple Mode C6h - Y - - D - 27 Set Sleep Mode E6h or 99h D - 28 SMART B0h Y Y - Y Y - 29 Standby E2h or 96h D - 30 Standby Immediate E0h or 94h D - 31 Translate Sector 87h - Y Y Y Y Y 32 Write Buffer E8h D - 33 Write DMA CAh - Y Y Y Y Y 34 Write Long Sector 32h or 33h - - Y Y Y Y 35 Write Multiple C5h - Y Y Y Y Y 36 Write Multiple w/o Erase CDh - Y Y Y Y Y 37 Write Sector(s) 30h or 31h - Y Y Y Y Y 38 Write Sector(s) w/o Erase 38h - Y Y Y Y Y 39 Write Verify 3Ch - Y Y Y Y Y Definitions: FR = Features Register CY = Cylinder Registers 9

10 DH = Device/Drive/Head Register LBA = Logical Block Address Mode Supported (see command descriptions for use). Y - The register contains a valid parameter for this command. For the Drive/Head Register Y means both the device and head parameters are used. D - only the device parameter is valid and not the head parameter; C The register contains command specific data (see command descriptions for use). 10

11 5. Environmental Specification 5.1 Temperature Parameter Temp Specifications Operating Normal Temp 0 C to 70 C Storage -40 C to 85 C Operating Wide Temp -40 C to 85 C Storage -55 C to 95 C Maximum temperature gradient 30 C per hour 5.2 Vibration Parameter Operating Specifications 20G, HZ 5.3 Shock Parameter Acceleration Force (G) Half-sine Pulse Duration (msec) Operating , , Non-Operating , , Regulations EMC Directive 73/23/ECC for product safety Directive 89/336/EEC FCC FCC 47CFR part 15 subpart B Class B. BSMI CE RoHs 11

12 6. Ordering Information P/N Capacity(Max) Remark CDC128MRI-F003A MB CDC256MRI-F103A MB CDC512MRI-F203A MB CDC001GRI-F303A005 1GB Toshiba SLC Normal-Temp CDC002GRI-F403A005 2GB CDC004GRI-F403A005 4GB CDC008GRI-F403A005 8GB CDI128MRI-F003A MB CDI256MRI-F103A MB CDI512MRI-F203A MB CDI001GRI-F303A005 1GB Toshiba SLC Wide-Temp CDI002GRI-F403A005 2GB CDI004GRI-F403A005 4GB CDI008GRI-F403A005 8GB 7. Contact Information A+CPI, a storage business company, specializes in the design and marketing of SSD, EDM, and Industry CF products. For further information, please reach us at the following contact information: ACPi Digital Co., Ltd. TEL: FAX: sales@acpigroup.com Address: 11F.-3, No.186, Jian 1st Rd., Zhonghe Dist., New Taipei City 235, Taiwan (R.O.C.) 12