INSTRUCTION MANUAL (M064B A)

Transcription

1 Consumption analysers SMART PLUGGING INSTRUCTION MANUAL (M064B A)

2 2

3 SAFETY PRECAUTIONS Follow the warnings described in this manual with the symbols shown below. DANGER Warns of a risk, which could result in personal injury or material damage. ATTENTION Indicates that special attention should be paid to a specifi c point. If you must handle the unit for its installation, start-up or maintenance, the following should be taken into consideration: Incorrect handling or installation of the unit may result in injury to personnel as well as damage to the unit. In particular, handling with voltages applied may result in electric shock, which may cause death or serious injury to personnel. Defective installation or maintenance may also lead to the risk of fi re. Read the manual carefully prior to connecting the unit. Follow all installation and maintenance instructions throughout the unit s working life. Pay special attention to the installation standards of the National Electrical Code. Refer to the instruction manual before using the unit In this manual, if the instructions marked with this symbol are not respected or carried out correctly, it can result in injury or damage to the unit and /or installations. CIRCUTOR, SA reserves the right to modify features or the product manual without prior notifi cation. DISCLAIMER CIRCUTOR, SA reserves the right to make modifi cations to the device or the unit specifi cations set out in this instruction manual without prior notice. CIRCUTOR, SA on its web site, supplies its customers with the latest versions of the device specifi cations and the most updated manuals. CIRCUTOR, recommends using the original cables and accessories that are supplied with the device. 3

4 CONTENTS SAFETY PRECAUTIONS...3 DISCLAIMER...3 CONTENTS...4 REVISION LOG...6 SYMBOLS VERIFICATIONS UPON RECEPTION DESCRIPTION OF THE PRODUCT INSTALLING THE DEVICE PRELIMINARY RECOMMENDATIONS INSTALLATION DEVICE TERMINALS Wibeee-M-L Wibeee-M-R Wibeee-T-L Wibeee-T-R Wibeee-3P CONNECTION DIAGRAMS Wibeee-M-L Wibeee-M-R Wibeee-T-L Wibeee-T-R Wibeee-3P STARTING UP THE DEVICE APPLICATION MODE DIRECT SHARE MODE CALIBRATION OPERATION OPERATING PRINCIPLE MEASUREMENT PARAMETERS Wibeee-M-L and Wibeee-M-R Wibeee-T-L, Wibeee-T-R and Wibeee-3P LED INDICATORS BUTTON START-UP DISPLAY AND CONFIGURATION MOBILE APPLICATION WEB PLATFORM HOME DASHBOARD DEVICES NOTIFICATIONS REPORTS HELP INTERNAL WEB SERVER INSTANT DATA NETWORK ADVANCED OPTIONS GENERAL OPTIONS CONFIGURATION THROUGH HTTP GET REQUESTS PARAMETER QUERY CONFIGURATION WIRELESS COMMUNICATIONS USAGE ENVIRONMENT AND HEALTH Wi-Fi COMMUNICATIONS MODBUS TCP PROTOCOL MODBUS MEMORY MAP TECHNICAL FEATURES MAINTENANCE AND TECHNICAL SERVICE

5 9.- WARRANTY CE CERTIFICATE

6 REVISION LOG Table 1: Revision log. Date Revision Description 01/18 M064B A Initial Version SYMBOLS Symbol Table 2: Symbols. Description Compliant with the relevant European standards. Do not remove from hazardous live conductors or place it around them. Double insulation. ~ AC current. Device covered by European directive 2002/96/EC. At the end of its useful life, do not leave the device in a household waste container. Follow local regulations on electronic equipment recycling. Note: The images of the devices are for illustration purposes only and may differ from the original device. 6

7 1.- VERIFICATIONS UPON RECEPTION The following must be checked upon reception of the device: a) The device has been supplied according to the specifications in your order. b) The device has not been damaged during transport. c) Perform an external visual inspection of the device before connecting it. d) Check that it has been supplied with the following: - An installation guide, - A set of magnets, 2.- DESCRIPTION OF THE PRODUCT Wibeee is a new method for electrical data acquisition, to facilitate decision making when it comes to understanding the use of electrical energy. The technology used, which is attached via a clip, is based on the patented DINZERO system and consists of simply attaching the device to the cable or to the upper part of an MCB (miniature circuit breaker). Once switched on, the device will begin to convert the measured parameters into information that is sent via a wireless connection. There are 5 models available: Wibeee-M-L single-phase model with a neutral connection on the left. Wibeee-M-R single-phase model with a neutral connection on the right. Wibeee-T-L three-phase model with a neutral connection on the left. Wibeee-T-R three-phase model with a neutral connection on the right. Wibeee-3P three-phase model with no neutral connection. The models have: - 2 indicator LEDs - 1 Reset button - Wi-Fi communications You can access the data measured by the device via the Wibeee Circutor mobile application, the website or the device's internal web server. 7

8 3.- INSTALLING THE DEVICE PRELIMINARY RECOMMENDATIONS In order to use the device safely, it is critical that individuals who handle it follow the safety measures set out in the standards of the country where it is being used, use the personal protective equipment necessary (rubber gloves, face protection and approved flame-resistant clothing) to prevent injuries due to electric shock or electric arc due to exposure to current-carrying conductors and pay attention to the various warnings indicated in this instruction manual. The Wibeee device must be installed by authorised and qualified staff. Disconnect the device from the power supply and disconnect the measuring devices before handling, changing the connections or replacing the device. Handling the device while it is connected is hazardous to people nearby. It is essential to keep the cables in a perfect condition to avoid accidents, personal injury and damage to installations. Limit the operation of the device to measuring the specified current or voltage values. The manufacturer of the device shall not be held responsible for any damage resulting from the user or installation company failing to observe the warnings and/or recommendations indicated in this manual nor for any damage resulting from the use of non-original products or accessories or those from other brands. Do not use the device to take measurements if you detect an anomaly or malfunction. Check the environment in which the device is installed before taking a measurement. Do not use the device to take measurements in dangerous, explosive, wet or damp environments. Disconnect the device from the mains and from the power supply (both the device and its measuring system) before performing any maintenance work, repairs or handling any of the connections of the device. Contact the after-sales service if you detect that the device is not working properly. 8

9 3.2.- INSTALLATION Before using the Wibeee ensure that the conditions are appropriate for working, and that the protective equipment is adequate. Use of the Wibeee on uninsulated conductors is limited to 265 V~ to the power frequency. For measuring of uninsulated conductors, use the appropriate and necessary personal protective equipment. The device should be installed after the circuit breaker. (Imax: 63 A) To install the device, carry out the following steps: 1. Remove the protective panel from the electric panel. Figure 1: Remove the connection panel. 2. When installing the device, make sure that the neutral terminal (N) corresponds with the neutral cable of the installation (your device could be damaged if incorrectly installed). Place the magnetic connectors in the direction of the circuit breaker and near to the casing of the Wibeee. Figure 2: Install the device. 9

10 3. Check that it is secured. 4. Check that the red LED is on and blinking. 5. After a few seconds, the blue LED will start blinking DEVICE TERMINALS Wibeee-M-L Table 3:List of terminals of the Wibeee-M-L. Terminals of the Wibeee-M-L device 1: N, Neutral 2: L1, Voltage input 1 2 Figure 3:Wibeee-M-L Terminals Wibeee-M-R Table 4:List of terminals of the Wibeee-M-R. Terminals of the Wibeee-M-R device 1: L1, Voltage input 2: N, Neutral 1 2 Figure 4:Wibeee-M-R Terminals. 10

11 Wibeee-T-L Table 5:List of terminals of the Wibeee-T-L. Terminals of the Wibeee-T-L device 1: N, Neutral 3: L2, Voltage input L2 2: L1, Voltage input L1 4: L3, Voltage input L Figure 5:Wibeee-T-L Terminals Wibeee-T-R Table 6:List of terminals of the Wibeee-T-R. Terminals of the Wibeee-T-R device 1: L1, Voltage input L1 3: L3, Voltage input L3 2: L2, Voltage input L2 4: N, Neutral Figure 6:Wibeee-T-R Terminals. 11

12 Wibeee-3P Table 7:List of terminals of the Wibeee-3P. Terminals of the Wibeee-3P device 1: L1, Voltage input L1 3: L3, Voltage input L3 2: L2, Voltage input L2 L2 L Figure 7:Wibeee-3P Terminals CONNECTION DIAGRAMS Wibeee-M-L N L Figure 8: Wibeee-M-L connection diagram. 12

13 Wibeee-M-R L N Figure 9: Wibeee-M-R connection diagram Wibeee-T-L N L1 L2 L3 Figure 10: Wibeee-T-L connection diagram. 13

14 Wibeee-T-R L1 L2 L3 N Figure 11: Wibeee-T-R connection diagram Wibeee-3P L1 L2 L3 Figure 12: Wibeee-3P connection diagram. 14

15 3.5.- STARTING UP THE DEVICE To start communication with the device it is necessary: 1.- To have access to the Internet through a wireless network. 2.- To check that the following ports are open: - Port 8080 for Http Get / Post. - Port 53 for DNS - Port 80 for Internet Note: The Orange Livebox Next router is incompatible with Wibeee devices when in WPA/ WPA2 security mode and they do not connect. When in only WPA2 mode they connect correctly. The Wibeee's data can be accessed in two ways: Application mode. Direct share mode APPLICATION MODE In application mode, the data measured by the Wibeee is uploaded to the cloud and accessed using the Wibeee CIRCUTOR application. When using this mode, the Wibeee and the user who has configured it are linked, so the user can control the device, view the data that has been sent and the charts and manage groups of devices. To start the device in application mode, follow these steps: 1.- Scan the QR code to download the application or download it from: Open the Wibeee CIRCUTOR application. And follow the steps that it indicates. 15

16 DIRECT SHARE MODE In direct share mode the Wibeee's data is directly accessed from the device's integrated web server, so you can view the measurements being captured at that moment in real time and manually configure the device. This allows you to change parameters, such as the server and port to which the Wibeee will send the data. If you configure a Wibeee while using this mode, there is no link between the user and the device, so the only way to access the device when it is connected to the network is by knowing its IP address and accessing it using a search tool. To start the device in direct share mode, follow these steps: 1.- On a smartphone/tablet, use the Wi-Fi connection's settings to connect to the Wibeee. 2.- You can get access to the net configuration and instant measurements through your browser, at the address: User: user Password: user 16

17 3.6.- CALIBRATION When the device has been installed and started, it needs to be calibrated. The calibration process appears automatically in the Wibeee Circutor mobile application during installation. Follow these steps: 1.- When the device has been successfully installed, measure the current of the L1 with a current clamp, and enter the value on the calibration screen, Figure 13. Note: calibration should be performed when the device has a current flow of A. Figure 13: Calibration screen. 2.- Repeat the calibration process for each of the device's measurement cables. If you skip the calibration process while installing the device, the accuracy of the measurements is not guaranteed. If the measurement cables are replaced or moved after calibration has been performed, it must be repeated. You can calibrate the device again via the Edit menu. 17

18 4.- OPERATION OPERATING PRINCIPLE The Wibeee is a power consumption measurement device with a Wi-Fi wireless connection to display or download the data that is measured, using any smartphone, tablet or PC. Electrical Panel Wibeee Laptop PC Smartphone Tablet Figure 14: Overview The device can work in two operating modes: Application mode In application mode, the data measured by the Wibeee is uploaded to the cloud and accessed via the Wibeee CIRCUTOR application or the web platform. Direct share mode In direct share mode the Wibeee's data is directly accessed from the device's integrated web server. Note: The device's integrated web server can also be accessed in the application's operating mode MEASUREMENT PARAMETERS The device measures and logs the following parameters: Wibeee-M-L and Wibeee-M-R Table 8: Measurement parameters of the Wibeee-M-L and Wibeee-M-R. Parameter Units Voltage V Current A Frequency Hz Active Power kw Apparent Power kva Inductive Reactive Power kvarl Capacitive Reactive Power kvarc Power Factor PF Active Energy kwh Reactive Energy kvarh 18

19 Table 8 (Cont.): Measurement parameters of the Wibeee-M-L and Wibeee-M-R. Parameter Units Inductive Reactive Energy kvarlh Capacitive Reactive Energy kvarch Cost - CO 2 Emissions KgCO Wibeee-T-L, Wibeee-T-R and Wibeee-3P Table 9: Measurement parameters of the Wibeee-T-L, Wibeee-T-R and Wibeee-3P. Parameter Units Phases L1-L2-L3 Voltage V Current A Frequency Hz Active Power kw Apparent Power kva Inductive Reactive Power kvarl Capacitive Reactive Power kvarc Power Factor PF Active Energy kwh Reactive Energy kvarh Inductive Reactive Energy kvarlh Capacitive Reactive Energy kvarch Cost - CO 2 Emissions KgCO 2 Total LED INDICATORS The device has 2 status LEDs, Figure 15 and Table 10. Blue Red Blue Red Blue Red L2 L3 Figure 15:LED indicators. 19

20 LED Red Blue Table 10: Description of the LEDs. Description Blinking light: Powered device. Indicates the connection status: Slow blinking light (1s): Generating a Wi-Fi network. Fast blinking light (<1s) : Connected to a Wi-Fi network. Steady light: Data being sent over the network BUTTON The device has a Reset button, Figure 16, to restore the device's factory settings (hold it down for more than 6 seconds). Reset Reset Reset L2 L3 Figure 16:Reset Button START-UP During the start-up of the device, the Wibeee goes through different states: 1.- Configuration state Blue LED Slow blinking light (1s) Red LED Slow blinking light (1s) In this state, the Wibeee generates its own Wi-Fi network called WIBEEE_xx:xx:xx. It is only used to configure the device and connect it to the user's network. If you want to return to this state to obtain the initial conditions, you should hold down the Reset button for more than 6 seconds. The device deletes any previous settings and restores the default values. 2.- Connecting... state Blue LED Off Red LED Slow blinking light (1s) In this state, the Wibeee is managing the connection with the router/access point. This state should last for 40 seconds, when there is good Wi-Fi coverage. In places where there is weak Wi-Fi coverage, it may take longer. 20

21 If it takes longer than 2 minutes, it is recommended to return to the initial state, check the Wi-Fi coverage and re-start the process. If it is unable to connect to the Wi-Fi, the device retries 5 times. If the lack of connection persists, it goes into Configuration mode (so that the configuration can be changed without opening the panel) for 5 minutes; it then tries to reconnect again and, until it manages to reconnect, it remains in this alternating mode. (5 minutes in the Configuration state and 1 attempt to connect). 3.- Connecting state Blue LED Fast blinking light (<1s) Red LED Slow blinking light (1s) In this state, the device has connected to the Wi-Fi network and is waiting to complete the first successful transfer of data. When it first manages to successfully send data, it will enter the Connected and sending OK state. If the device is not able to successfully send the first set of data, it will retry 3 times. If it does not manage to send it, the Wi-Fi connection is restarted and it retries sending the package 3 times. It remains in this state until the first data is successfully sent. 4.- Connected and sending OK state Blue LED Steady light. Red LED Slow blinking light (1s) When the device is configured and connected to the network in the user's infrastructure, it automatically starts sending data on the installation's power consumption to the server (every minute). It also allows you to access instant measurements by making requests to its internal XML and Modbus servers. 21

22 5.- DISPLAY AND CONFIGURATION When the device has been installed and started up, it is possible to access all of its data by using different methods, depending on the device's operating mode, Figure 17. Application mode Direct share mode Data display Web platform Mobile application Wibeee Circutor Internal Web server Internal Web server Figure 17: Data display based on the operating mode MOBILE APPLICATION The Wibeee Circutor mobile application is compatible with ios and Android, and has a version for smartphones and tablets. In it you can view and configure all of the parameters measured by the device. Figure 18: Wibeee Circutor mobile application. 22

23 5.2.- WEB PLATFORM Figure 19 shows the main screen of the web platform. Figure 19:Main screen of the web platform. From this screen you can access the different sections of the platform: : Home, summary of consumption, displays charts and gives access to the dashboard configuration options (graphical interface). : Dashboard, displays all of the dashboards of every active device. : Devices, access to all of the connected devices. : Notifications, displays the notifications log. : Reports, access to regular report generation. : Help, help screen. 23

24 HOME The Home screen is divided into different areas: The area in Figure 20 displays a summary of consumption and CO 2 emissions from the previous month, the current month and the forecast for the end of the month. It also displays the set target value. Figure 20: Summary area. The area in Figure 21 shows 2 of the possible charts that can be viewed. Table 8 and Table 9 show all of the parameters that can be graphically displayed. Use the < > arrows to toggle between charts. 24

25 Figure 21: Charts area. The area in Figure 22 shows the latest measurements sent by the device. Figure 22: Measurements area. In the area in Figure 23 you can access the configuration options for the devices and dashboard, see Configuration screen for the devices/dashboard. Figure 23: Access to the device/dashboard configuration area. 25

26 Configuration screen for the devices/dashboard. On the device/dashboard configuration screen you can configure the following data: DEVICE Figure 24: Configuration screen: Device. The device's basic data is entered in this section: Name: The name of the device. Select Dashboard: Dashboard selection. Mac: MAC address of the device. 2-4 Quadrants: Measurement selection for 2 quadrants (consumption) or 4 quadrants (consumption and generation). LOCATION Figure 25: Configuration screen: Location. 26

27 The device's location data is entered in this section: Name: Name of the device's location. Time zone: Time zone. Longitude, Latitude: Location of the device. COST Figure 26: Configuration screen: Cost The costs are entered in this section: Price kwh : Price of kwh. Tax (%), Other Tax (%) : Fees and taxes. Other Costs (Cost/day): Other costs. Cost kw Day (Cost/kW Day): Cost in kw per day. Billing date: Billing date. Contracted power (kw): Contracted power. TARGET AND NOTIFICATIONS Figure 27: Configuration screen: Target and Notifications. 27

28 In this section you enter the following: Target Limit (kwh) : The maximum consumption value that you want to reach, in kwh. And the following notifications are activated or deactivated: Wibeee has been inactive for 1 day. Wibeee has been inactive for 3 days. Overvoltage, overvoltage alarm. Undervoltage, undervoltage alarm. High consumption, alarm for high consumption in the installation DASHBOARD The Dashboard screen, Figure 28, shows all of the active dashboards. Figure 28: Dashboard Screen. It is also possible to create a chart comparing different dashboards. To do this, simply select the dashboards that you want to compare by ticking the box, as shown in Figure 29. Figure 29: Selecting the Factory dashboard. 28

29 DEVICES The Devices screen, Figure 30, displays a list of all of the connected devices. Figure 30: Devices screen NOTIFICATIONS The Notifications screen, Figure 31, shows a log of all of the notifications that have been generated. Figure 31: Notifications screen. 29

30 REPORTS The Reports screen, Figure 32, is divided into two areas: Figure 32: Reports Screen. REPORTS This section shows the scheduled reports to be regularly generated. To create a new regular report, press the icon. The dialogue box in Figure 33 opens. Figure 33: New Report. 30

31 In this dialogue box, you should enter: Report name: Name with which the report is going to be saved. Select Dashboard: Select the Dashboard on which you are going to prepare the report. Frequency: Select the frequency of the report: Weekly, Monthly, Billing period. Recipients: Enter the addresses of the recipients of the report. You can prepare a simple version of a report by selecting Normal Section (Figure 33), where everything is pre-configured and you only have to select the quantity. Or an advanced version, by selecting Advanced Section (Figure 34), where you can configure a lot more options. Figure 34: New Report: Advanced Section. REPORT LOG In this section you can download all of the reports that have already been created. 31

32 HELP The Help screen, Figure 35, tries to answer any questions about the installation, operation, web platform and application of the two Wibeee systems. Figure 35: Help Screen INTERNAL WEB SERVER Figure 36 shows the screen where you access the device's internal web server. The device's default address is: User: user Password: user Figure 36:Internal web server access screen. The main screen is shown in Figure

33 Figure 37:Main screen of the internal web server INSTANT DATA In this section you can access instant data from each of the measurement phases, Figure 38. Figure 38:Internal web server: Instant Data. 33

34 NETWORK You can configure the network parameters in the Network section, Figure 39. Figure 39:Internal web server: Network ADVANCED OPTIONS You can configure the IP parameters in the Advanced Options section, Figure 40. wibeee.circutor.com Figure 40:Internal web server: Advanced Options. 34

35 GENERAL OPTIONS Figure 41 shows the General Options section. Figure 41:Internal web server: General Options. You can configure the following parameters in this section: Measures Refresh Time (s): The measurement refresh time. Data Refresh Time (min): The data refresh time. If the value is set to -1, the sending of data is deactivated. It is also possible to reset the energy meter, by pressing the button CONFIGURATION THROUGH HTTP GET REQUESTS Wibeee accepts HTTP GET requests for parameter and settings queries for the device. Requests must be made directly to the IP address: after connecting to the Wi-Fi network created by the device. All requests made to the Wibeee's internal server are GET requests and when they have been processed by the server it sends an HTTP correct access response: HTTP 200 OK PARAMETER QUERY DEVICE ID You should use the following request to view the device's ID: 35

36 Figure 42: HPPT queries: Device ID Values of the device's variables To view the values of all of the device's variables, use the following request: It is also possible to view specific variables, see Table 11 with the available variables. Figure 43:HPPT queries: Values of the device's variables. Table 11: Variables table. Variable Description Units <var>measuresrefresh</var> Measures refresh time of the internal web Seconds <var>apprefresh</var> Time sending data to the server. Minutes <var>softversion</var> Firmware version of the device - <var>model</var> Model identifier - <var>ipaddr</var> Type of IP : DHCP or static IP - <var>gwaddr</var> The device's current IP. - <var>subnetmask</var> Gateway. - 36

37 Table 11 (Cont.): Variables table Variable Description Units <var>primarydns</var> Primary DNS server. - <var>secondarydns</var> Secondary DNS server. - <var>macaddr</var> MAC identifier - <var>ssid</var> Name of the network. - <var>keyenc</var> Password type. - <var>keytype</var> Password format: Hex or ASCII - <var>securkey</var> Password. - <var>serverip</var> Name of the server domain. - <var>serveripresolved</var> IP address of the server. - <var>serverport</var> Sending port. - <var>vrms1</var> Phase voltage L1 V <var>vrms2</var> Phase voltage L2 V <var>vrms3</var> Phase voltage L3 V <var>vrmst</var> Total voltage (average of L1, L2, L3) V <var>irms1</var> Current L1 A <var>irms2</var> Current L2 A <var>irms3</var> Current L3 A <var>irmst</var> Total current (average of L1, L2, L3) A <var>pap1</var> Apparent Power L1 VA <var>pap2</var> Apparent Power L2 VA <var>pap3</var> Apparent Power L3 VA <var>papt</var> Total Apparent Power VA <var>pac1</var> Active Power L1 W <var>pac2</var> Active Power L2 W <var>pac3</var> Active Power L3 W <var>pact</var> Total Active Power W <var>preac1</var> L1 Reactive Power Var <var>preac2</var> L2 Reactive Power Var <var>preac3</var> L3 Reactive Power Var <var>preact</var> Total Reactive Power Var <var>freq1</var> Frequency L1 Hz <var>freq2</var> Frequency L2 Hz <var>freq3</var> Frequency L3 Hz <var>freqt</var> Total frequency (average of L1, L2, L3) Hz <var>fpot1</var> Power Factor L1 - <var>fpot2</var> Power Factor L2 - <var>fpot3</var> Power Factor L3 - <var>fpott</var> Total Power Factor - <var>eac1</var> Active Energy L1 Wh <var>eac2</var> Active Energy L2 Wh <var>eac3</var> Active Energy L3 Wh <var>eactt</var> Total Active Energy Wh <var>ereactl1</var> Inductive Reactive Energy L1 VArLh <var>ereactl2</var> Inductive Reactive Energy L2 VArLh 37

38 Table 11 (Cont.): Variables table Variable Description Units <var>ereactl3</var> Inductive Reactive Energy L3 VArLh <var>ereactlt</var> Total Inductive Reactive Energy VArLh <var>ereactc1</var> Capacitive Reactive Energy L1 VArCh <var>ereactc2</var> Capacitive Reactive Energy L2 VArCh <var>ereactc3</var> Capacitive Reactive Energy L3 VArCh <var>ereactct</var> Total Capacitive Reactive Energy VArCh CONFIGURATION The minimum requests for configuring the Wibeee with HPPT are: 1.- Device Network configuration: Table 12: Configuration HPPT variables (Request 1) Variable Description name Name of the Wibeee dhcp false: static network true: dynamic network ip IP address in hexadecimal gw Gateway in hexadecimal subnet Subnet mask in hexadecimal 2.- Configuration of the Local Wi-Fi Network: Variable ssid security typekey Table 13: Configuration HPPT variables (Request 2) Description Name of the Wi-Fi Type of security: 0: OPEN - 1: WEP - 5:WPA - 9: WPA2-13: WPA/WPA2 Password encryption: 1: Hexadecimal - 2: PassPhrase 3.- Password sending: 38

39 Table 14: Configuration HPPT variables (Request 3) Variable Description pass Wi-Fi password 4.- Server Configuration: id= Table 15: Configuration HPPT variables (Request 4) Variable Description ServerURL Name of the server domain Serverport Port in hexadecimal 5.- Resetting the device: 39

40 6.- WIRELESS COMMUNICATIONS USAGE ENVIRONMENT AND HEALTH Wireless communications emit radio frequency electromagnetic energy, like other radio devices. Because wireless communications operate within the guidelines found in radio frequency safety standards and recommendations, they are safe for users to use. In certain environments or situations, the use of wireless communications may be restricted by the owner of the building or the representatives responsible for the organisation. These situations include: The use of wireless connections on board aircraft, in hospitals or near to service stations, blasting areas, medical implants or electronic medical devices implanted in the body (pacemakers etc.). In any other environment where the risk of interference with other devices or services is identified as hazardous. If you are unsure about the policy implemented regarding the use of wireless devices in a specific organisation (airport, hospital, etc.), it is advisable to ask for authorisation to use wireless communications Wi-Fi COMMUNICATIONS Wi-Fi is one of the most widely used wireless technologies today, for connecting and exchanging information between electronic devices without having to connect them physically. The Wibeee has Wi-Fi communications in the 2.4 GHz band, compliant with standard IEEE MODBUS TCP PROTOCOL The MODBUS protocol is an industry communication standard that enables the network connection of multiple devices, where there is a master and multiple slaves. The MODBUS functions implemented in the device are: Function 0x03. Reading of multiple registers. This function is used to request the desired measurement parameters from the Wibeee Modbus server. Function 0x05. Writing of a specific register. This function is used to delete the Wibeee's energy meters. If the Wibeee receives a function request other than those above, or for non-specified memory registers, the device identifies this as an Illegal error and responds with the appropriate exception code. 40

41 As it is a MODBUS TCP server, the device number internally assigned to the Wibeee is 1. By default, once configured, the Wibeee starts to send data over the internet to the CIRCUTOR server. If you want to stop this data from being sent (for example, because the local network does not have an Internet connection) you have to set a data refresh time of -1. This way, the device is only waiting to handle MODBUS requests MODBUS MEMORY MAP All MODBUS map addresses are in hexadecimal format. Table 16: Modbus memory map Parameter Symbol Address Units Wibeee model Phase voltage L1 Vrms1x V x 10 Single-phase Three-phase Phase voltage L2 Vrms2x V x 10 Three-phase Phase voltage L3 Vrms3x V x 10 Three-phase Current L1 Irms1x A x 10 Single-phase Three-phase Current L2 Irms2x A x 10 Three-phase Current L3 Irms3x A x 10 Three-phase Frequency L1 Freq1x Hz x 10 Single-phase Three-phase Frequency L2 Freq2x Hz x 10 Three-phase Frequency L3 Freq3x Hz x 10 Three-phase Total Frequency FreqTx Hz x 10 Single-phase Three-phase Active Power L1 Wreal1x10 000A W x 10 Single-phase Three-phase Active Power L2 Wreal2x10 000B W x 10 Three-phase Active Power L3 Wreal3x10 000C W x 10 Three-phase Total Active Power WrealTx10 000D W x 10 Three-phase L1 Reactive Power Wreact1x10 000E Var x 10 Single-phase Three-phase L2 Reactive Power Wreact2x10 000F Var x 10 Three-phase L3 Reactive Power Wreact3x Var x 10 Three-phase Total Reactive Power WreactTx Var x 10 Three-phase Apparent Power L1 Waparent1x VA x 10 Single-phase Three-phase Apparent Power L2 Waparent2x VA x 10 Three-phase Apparent Power L3 Waparent3x VA x 10 Three-phase Total Apparent Power WaparentTx VA x 10 Three-phase Power Factor L1 PF1 x x 100 Single-phase Three-phase Power Factor L2 PF2 x x 100 Three-phase Power Factor L3 PF3 x x 100 Three-phase Total Power Factor TPF x x 100 Three-phase Active Energy L1 Eact1 001A - 001B kwh Single-phase Three-phase 41

42 Table 16 (Cont.): Modbus memory map. Parameter Symbol Address Units Wibeee model Active Energy L2 Eact2 001C - 001D kwh Three-phase Active Energy L3 Eact3 001E - 001F kwh Three-phase Total Active Energy EactT kwh Three-phase Inductive Reactive Energy L1 EreactL kvarh Single-phase Three-phase Inductive Reactive Energy L2 EreactL kvarh Three-phase Inductive Reactive Energy L3 EreactL kvarh Three-phase Total Inductive Reactive Energy EreactLT kvarh Three-phase Capacitive Reactive Energy L1 EreactC1 002A - 002B kvarh Single-phase Three-phase Capacitive Reactive Energy L2 EreactC2 002C - 002D kvarh Three-phase Capacitive Reactive Energy L3 EreactC3 002E - 002F kvarh Three-phase Total Capacitive Reactive Energy EreactCT kvarh Three-phase Function 05 is used to delete energy meters. Table 17:Modbus memory map: Deleting parameters Deleting parameters Address Value to be sent Deleting energy meters xFF00 42

43 7.- TECHNICAL FEATURES Note: The metrological specifications given are always with the range of adjustment. Power supply Rated Voltage Wibeee-M-x, Wibeee-T-x (1) Wibeee-3P (1) 85 to 265 V ~ V ~ (Ph-Ph) Frequency Hz Hz Consumption VA VA (1) The Wibeee-T model is powered between L1 and N. The WiBeee-3P model is powered between L2 and L3. Voltage measurement circuit Voltage measurement margin Wibeee-M-x, Wibeee-T-x Wibeee-3P 85 to 265 V ~ V ~ (Ph-Ph) Frequency measurement margin Hz Hz Min. voltage measurement (Vstart) 85 V 100 V Installation category CAT III CAT III Current measurement circuit Current measurement margin Wibeee-M-x, Wibeee-T-x Wibeee-3P A A Min. current measurement (Istart) 500 ma 500 ma Installation category CAT III CAT III Measurement accuracy Voltage measurement 2 % + variations in range of use (at PF = 1) Current measurement 2 % + variations in range of use Power measurement 4 % + variations in range of use Variations in Range of Use Magnitude of influence Range of influence Typical Maximum Temperature - 10ºC ºC % Relative humidity 10%... 90% % Crosstalk (current) % - External demagnetising field (current) - 1 % - Conductor position - 2 % 3 % Adjust Full Scale 0.2 % 0.4 % Distance between wire and sensor - 2.5% / 0.1 mm - Communications Type Wi-Fi (IEEE ) Protocol HTTP, Modbus/TCP, XML Frequency Range GHz Encryption AES128 Monthly data consumption 300 MB FCC (USA), IC (CANADA), ETSI (EUROPA) Certified LED Button Mobile application User interface 2 LEDs 1 button Wibeee Circutor 43

44 Environmental features Operating temperature -10ºC ºC Storage temperature -40ºC ºC Relative humidity (without condensation) % Maximum altitude 2000 m Protection degree IP40 Insulation Double insulation Mechanical features Dimensions (mm) Wibeee-M-x Wibeee-T-x Wibeee-3P Figure 44 Figure 45 Figure 46 Weight 37 g 64 g 53 g Surround Self-extinguishing VO Plastic (UNE ºC) 50, Figure 44: Dimensions : Wibeee-M-L and Wibeee-M-R. 50, Figure 45: Dimensions : Wibeee-T-L y Wibeee-T-R. 47,87 53,40 49 Figure 46: Dimensions : Wibeee-3P. 44

45 Standard Safety requirements for electrical equipment for measurement, control and laboratory use -- Part 2-030: Particular requirements for testing and measuring circuits Electrical equipment for measurement, control and laboratory use - EMC requirements -- Part 1: General requirements (IEC :2005) Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment; Part 17: Specific conditions for Broadband Data Transmission Systems UNE-EN :2011 UNE-EN :2006 EN V

46 8.- MAINTENANCE AND TECHNICAL SERVICE In the case of any query in relation to device operation or malfunction, please contact the CIRCUTOR, SA Technical Support Service. Technical Assistance Service Vial Sant Jordi, s/n, Viladecavalls (Barcelona) Tel: ( España) / (outside of Spain) sat@circutor.com 9.- WARRANTY CIRCUTOR guarantees its products against any manufacturing defect for two years after the delivery of the units. CIRCUTOR will repair or replace any defective factory product returned during the guarantee period. No returns will be accepted and no unit will be repaired or replaced if it is not accompanied by a report indicating the defect detected or the reason for the return. The guarantee will be void if the units has been improperly used or the storage, installation and maintenance instructions listed in this manual have not been followed. Improper usage is defi ned as any operating or storage condition contrary to the national electrical code or that surpasses the limits indicated in the technical and environmental features of this manual. CIRCUTOR accepts no liability due to the possible damage to the unit or other parts of the installation, nor will it cover any possible sanctions derived from a possible failure, improper installation or improper usage of the unit. Consequently, this guarantee does not apply to failures occurring in the following cases: - Overvoltages and/or electrical disturbances in the supply; - Water, if the product does not have the appropriate IP classifi cation; - Poor ventilation and/or excessive temperatures; - Improper installation and/or lack of maintenance; - Buyer repairs or modifi cations without the manufacturer s authorisation. 46

47 10.- CE CERTIFICATE 47

48 48

49 49

50 CIRCUTOR, SA Vial Sant Jordi, s/n Viladecavalls (Barcelona) Tel.: (+34) Fax: (+34) central@circutor.com