E2FM. Inductive Proximity Sensor in full metal housing. Application. Continuous Impact Test. Brush Test

Transcription

1 Inductive Proximity Sensor in full metal housing Full body stainless steel housing for highest mechanical protection Low frequency modulation for metal chip iunity Flame retardant cable for high protection against welding spatter damage Application Full body stainless steel housing with.8 thick sensing face protection.8 Brush Test The stainless-steel head shows minimal wear when cleaned with a metal brush. Continuous Impact Test More than times the durability of standard sensors. Standard sensor Standard sensor The standard sensor with top wall thickness of. was penetrated after, impacts. The was not penetrated after 5, impacts (depth:.6 ). A-

2 Features Chemical and Oil Resistance (examples) Tested resistance against: Sodium chloride Gasoline Dilute sodium hydroxide Dilute hydrochloric acid Mineral oil Barium hydroxide Low frequency modulation......for metal chip iunity reducing false signals caused by spatter accumulation and small metal objects. Flush mounting installation possible Minimum installation distance Workpiece conventional products Workpiece Not influenced by surrounding installation environment. Note: When mounted in steel. Ordering Information Sensors DC -Wire, Pre-wired Connector Models Appearance Sensing distance Output configuration Operation mode Model M8.5 Polarity: Yes, Pin allocations: - -XR5D-MGJ Polarity: Yes, -XD-MGJ Pin allocations: - M No polarity: No, -XD-MGJ-T Pin allocations: 3- M8 5 Polarity: Yes, Pin allocations: - -X5D-MGJ No polarity: No, Pin allocations: 3- -X5D-MGJ-T M3 Polarity: Yes, Pin allocations: - -XD-MGJ No polarity: No, Pin allocations: 3- -XD-MGJ-T DC 3-Wire, M Connector Models Appearance Sensing distance Output configuration Operation mode Model M8.5 -XR5B-M M M8 5 DC 3-Wire, PNP -XB-M -X5B-M M3 -XB-M A- Inductive Proximity Sensor

3 Rating and Specifications DC -Wire Size M8 M M8 M3 M M8 M3 -XR5D -XD -X5D -XD -XD -X5D -XD Model Item -MGJ -MGJ -MGJ -MGJ -MGJ-T -MGJ-T -MGJ-T Sensing distance.5 ±% ±% 5 ±% ±% ±% 5 ±% ±% Set distance to.5 to. to 3.5 to 7 to. to 3.5 to 7 Differential travel 5% max. of sensing distance Sensing object Ferrous metal (The sensing distance decreases with non-ferrous metal. Refer to Engineering Data on page 5.) Standard sensing object Response frequency * Hz Hz Hz 5 Hz Hz Hz 5 Hz Power supply voltage (operating voltage to VDC ( to 3 VDC), ripple (p-p): % max. range) Leakage current.8 ma max. Output configuration With polarity Without polarity Control output Indicators Switching capacity Residual voltage Operation mode (with sensing object approaching) Protection circuits Ambient temperature range Ambient humidity range Temperature influence Voltage influence Insulation resistance Dielectric strength Vibration resistance Shock resistance Degree of protection 3 to ma 3 V max. (Load current: ma, Cable length: m) Operation indicator (red LED), Setting/Operation indicator (green LED) Surge suppressor, Load short-circuit protection Operating/Storage: -5 to 7 C (with no icing or condensation) Operating/Storage: 35% to 95% (with no condensation) ±% max. of sensing distance at 3 C in the temperature range of -5 to 7 C. ±% max. of sensing distance at rated voltage in the rated voltage ±5% range 5 MΩ min. (at 5 VDC) between current-carrying parts and case, VAC, 5/6 Hz for minute between current carry parts and case 5 V max. (Load current: ma, Cable length: m) Destruction: to 55 Hz,.5 double amplitude for hours each in X, Y, and Z directions Destruction: 5 m/s times each in X, Y, and Z directions Destruction:, m/s times each in X, Y, and Z directions IEC 659 IP67, DIN 5 part 9: IP69k Connection method Pig-tail Connector Models (Standard cable length:.3 m) Weight (packed state) Approx. 65 g Approx. 85 g Approx. g Approx. 9 g Approx. 85 g Approx. g Approx. 9 g Case Stainless steel (SUS33) Sensing surface Stainless steel (SUS33) Materials Accessories (thickness) (. ) (.8 ) (.8 ) Clamping Cable Toothed washer Stainless steel (SUS33) PVC (flame retardant) Zinc-plated iron Instruction manual * The response frequency of the DC switching section is an average value. Measurement conditions are as follows: standard sensing object, a distance of twice the standard sensing object, and a set distance of half the sensing distance. A-3

4 DC 3-Wire Size M8 M M8 M3 Item Model -XR5B-M -XB-M -X5B-M -XB-M Sensing distance.5 ±% ±% 5 ±% ±% Set distance to.5 to. to 3.5 to 7 Differential travel 5% max. of sensing distance Sensing object Ferrous metal (The sensing distance decreases with non-ferrous metal. Refer to Engineering Data on page 5.) Standard sensing object Response frequency * Hz Hz Hz 5 Hz Power supply voltage (operating voltage range) Current consumption Output configuration Control output Indicators Switching capacity Residual voltage Operation mode (with sensing object approaching) Protection circuits Ambient temperature range Ambient humidity range Temperature influence Voltage influence Insulation resistance Dielectric strength Vibration resistance Shock resistance Degree of protection Connection method to VDC ( to 3 VDC), ripple (p-p): % max. ma max. PNP open collector output ma max. V max. (Load current: ma, Cable length: m) Operation indicator (yellow LED) Reversed power supply polarity protection, Surge suppressor, Load short-circuit protection, and Reversed output polarity protection (except the -XR5B-M) Operating/Storage: -5 to 7 C (with no icing or condensation) Operating/Storage: 35% to 95% (with no condensation) ±% max. of sensing distance at 3 C in the temperature range of -5 to 7 C. ±% max. of sensing distance in the rated voltage ±5% range (using the sensing distance at the rated voltage as standard) 5 MΩ min. (at 5 VDC) between current-carrying parts and case, VAC, 5/6 Hz for minute between current carry parts and case Destruction: to 55 Hz,.5- double amplitude for hours each in X, Y, and Z directions Destruction: 5 m/s times each in X, Y, and Z directions IEC 659 IP67, DIN 5 part 9: IP69k Connector Models Destruction:, m/s times each in X, Y, and Z directions Weight (packed state) Approx. 5 g Approx. 55 g Approx. 75 g Approx. 6 g Case Stainless steel (SUS33) Sensing surface Stainless steel (SUS33) Materials Accessories (thickness) (.) (.8) Clamping Toothed washer Stainless steel (SUS33) Zinc-plated iron Instruction manual * The response frequency of the DC switching section is an average value. Measurement conditions are as follows: standard sensing object, a distance of twice the standard sensing object, and a set distance of half the sensing distance. A- Inductive Proximity Sensor

5 Engineering Data (Typical) Sensing Area Influence of Sensing Object Size and Material Distance X () 8 6 -X@ -X5@ Distance X ().5. Iron.5 Distance X () Iron -XR5@ -XD@ Distance Y ()..5 Stainless steel (SUS3) Brass Aluminum Copper Side length of sensing object: d ()..5 Stainless steel (SUS3) Aluminum Brass Copper Side length of sensing object: d () Leakage Current -X5@ -X@ -X@D-MGJ(-T) Distance X () Iron Stainless steel (SUS3) Brass Aluminum Copper 6 8 Side length of sensing object: d () Distance X () 8 6 Iron Stainless steel (SUS3) Brass Aluminum Copper Side length of sensing object: d () Leakage current (ma) XR5D-MGJ -XD-MGJ(-T) -X5D-MGJ(-T) -XD-MGJ(-T) Power supply voltage (V) Residual Output Voltage -X@B-M Residual output voltage (V).5 -X@D-MGJ(-T) Residual output voltage (V) 5 -X@D-MGJ-T 3 -X@D-MGJ.5 -XB-M -X5B-M -XB-M -XR5B-M 5, Load current (ma) Load current (ma) A-5

6 I/O Circuit Diagrams DC -Wire Models Operation mode Model Timing chart Output circuit - X@D- MGJ Non-sensing area Sensing object Unstable sensing area Set position Stable sensing area Proximity sensor Proximity sensor main circuit Note: The load can be connected to either the +V or V side. Load to VDC V Connector Pin Arrangement Note: Pins and 3 are not used. - X@D- MGJ-T (%) 7 (TYP) Rated sensing distance ON OFF ON OFF ON OFF Setting indicator (green) Operation indicator (red) Control output Proximity sensor main circuit Load to VDC Connector Pin Arrangement 3 V ( to VDC) Note: Pins and are not used. Note. The load can be connected to either the +V or V side.. The -X@@-MGJ-T has no polarity. There is no need to be concerned about the polarity of pins 3 and. DC 3-Wire Models Operation mode Output configuration Model Timing chart Output circuit PNP opencollector model - XR5B- M - XB-M - X5B-M - XB-M Sensing object (%) Non-sensing area Rated sensing distance Sensing area Proximity sensor ON Operation indicator OFF (yellow) ON Control output OFF Proximity sensor main circuit 3 to VDC Load V Note: There is no reversed output polarity protection diode. Proximity sensor main circuit 3 to VDC Load V Connector Pin Arrangement Note: Pin is not used. Connector Pin Arrangement Note: Pin is not used. A-6 Inductive Proximity Sensor

7 Safety Precautions WARNING This product is not designed or rated for ensuring safety of persons. Do not use it for such purposes. Never use this product with an AC power supply. Otherwise, explosion may result. Precautions for Safe Use The following precautions must be observed to ensure safe operation.. Do not use the Sensor in an environment where inflaable or explosive gas is present.. Do not attempt to disassemble, repair, or modify any Sensors. 3. Power Supply Voltage Do not use a voltage that exceeds the rated operating voltage range. Applying a voltage that is higher than the operating voltage range may result in explosion or fire.. Incorrect Wiring Be sure that the power supply polarity and other wiring is correct. Incorrect wiring may cause explosion or fire. 5. Connection without a Load If the power supply is connected directly without a load, the internal elements may explode or burn. Be sure to insert a load when connecting the power supply. Precautions for Correct Use Do not use the Sensor under ambient conditions that exceed the ratings to ensure maximum lifetime:. Please do not use the Sensor in the following locations. () Outdoor locations directly subject to sunlight, rain, snow, or water droplets () Locations subject to atmospheres with chemical vapors, in particular solvents and acids (3) Locations subject to corrosive gas. The Sensor may malfunction if used near ultrasonic cleaning equipment, high-frequency equipment, transceivers, cellular phones, inverters, or other devices that generate a high-frequency electric field. Refer to the Sensor General Catalog for typical measures. 3. Laying the Sensor wiring in the same conduit or duct as highvoltage wires or power lines may result in incorrect operation and damage due to induction. Wire the Sensor using a separate conduit or independent conduit.. Cleaning Never use thinner or other solvents. Otherwise, the Sensor surface may be dissolved. Design Influence of Surrounding Metal When the Proximity Sensor is embedded in metal, make sure that the clearances given in the following table are maintained. The values depend on the type of used for mounting. Be sure to use the supplied (SUS33). l D d dia. l n m Model -XR5@ -X@ -X5@ -X@ Item Embedding material (Unit: ) l d D m n Iron Aluminum Iron 8 Aluminum Iron 8 6 Aluminum Iron 3 Aluminum Note: The influence from other non-magnetic surrounding metals is nearly the same as that from aluminum. Mutual Interference When installing two or more Sensors face-to-face or side-byside, ensure that the minimum distances given in the following table are maintained. (Unit: ) Model Item A B -XR5@ 35 3 A -X@ 35 -X5@ 65 6 B -X@ Chips from Cutting Aluminum or Cast Iron Normally, chips from cutting aluminum or cast iron will not cause a detection signal to be output even if it adheres to or accumulates on the detection surface. In the following cases, however, a detection signal may be output. Remove the cutting chips in these cases.. If d 3 D at the center of the detection surface where d is the cutting chip size and D is the detection surface size Model Dimension () D -XR5@ 6 -X@ -X5@ 6 -X@ 8 Mounting Do not tighten the nut with excessive force. A washer must be used with the nut. Do not use tightening force that exceeds the values in the following table. Model -XR5@ -X@ -X5@ -X@ Torque 9 N m 3 N m 7 N m 8 N m d D Pressed down Cutting chip Detection surface Cutting chips A-7

8 Dimensions Sensors -XR5D-MGJ Pig-tail Connector Models -XD-MGJ -XD-MGJ-T (Unit: ) 5 dia dia M8 -X5D-MGJ -X5D-MGJ-T Indicator * *. -dia. vinyl-insulated round cable (flame retardant), Standard length; 3 *. Operation indicator (red/green) Setting indicator (green) * 7 -XD-MGJ -XD-MGJ-T Two clamping Indicator * *. 6-dia. vinyl-insulated round cable (flame retardant), Standard length; 3 *. Operation indicator (red/green) Setting indicator (green) * 9 dia dia M8 Indicator * * *. 6-dia. vinyl-insulated round cable (flame retardant), Standard length; 3 *. Operation indicator (red/green) Setting indicator (green) 36 M3.5 Indicator * *. 6-dia. vinyl-insulated round cable (flame retardant), Standard length; 3 *. Operation indicator (red/green) Setting indicator (green) * M Connector Models -XR5B-M -XB-M 5 dia dia X5B-M M8 Two clamping Four operation indicators (yellow) 7 -XB-M Four operation indicators (yellow) dia dia M8 Four operation indicators (yellow) 36 M3.5 Four operation indicators (yellow) Mounting Hole Dimensions F Dimension M8 M M8 M F () 8.5 dia..5 dia. 8.5 dia. 3.5 dia. A-8 Inductive Proximity Sensor

9 READ AND UNDERSTAND THIS DOCUMENT Please read and understand this document before using the products. Please consult your OMRON representative if you have any questions or coents. WARRANTY OMRON s exclusive warranty is that the products are free from defects in materials and workmanship for a period of one year (or other period if specified) from date of sale by OMRON. OMRON MAKES WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING N-INFRINGEMENT, MERCHANTABILITY, OR FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS. ANY BUYER OR USER ACKWLEDGES THAT THE BUYER OR USER ALONE HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. OMRON DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. LIMITATIONS OF LIABILITY OMRON SHALL T BE RESPONSIBLE FOR SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED ON CONTRACT, WARRANTY, NEGLIGENCE, OR STRICT LIABILITY. In no event shall responsibility of OMRON for any act exceed the individual price of the product on which liability is asserted. IN EVENT SHALL OMRON BE RESPONSIBLE FOR WARRANTY, REPAIR, OR OTHER CLAIMS REGARDING THE PRODUCTS UNLESS OMRON S ANALYSIS CONFIRMS THAT THE PRODUCTS WERE PROPERLY HANDLED, STORED, INSTALLED, AND MAINTAINED AND T SUBJECT TO CONTAMINATION, ABUSE, MISUSE, OR INAPPROPRIATE MODIFICATION OR REPAIR. SUITABILITY FOR USE THE PRODUCTS CONTAINED IN THIS DOCUMENT ARE T SAFETY RATED. THEY ARE T DESIGNED OR RATED FOR ENSURING SAFETY OF PERSONS, AND SHOULD T BE RELIED UPON AS A SAFETY COMPONENT OR PROTECTIVE DEVICE FOR SUCH PURPOSES. Please refer to separate catalogs for OMRON's safety rated products. PERFORMANCE DATA Performance data given in this document is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of OMRON s test conditions, and the users must correlate it to actual application requirements. Actual performance is subject to the OMRON Warranty and Limitations of Liability. CHANGE IN SPECIFICATIONS Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice to change model numbers when published ratings or features are changed, or when significant construction changes are made. However, some specifications of the product may be changed without any notice. When in doubt, special model numbers may be assigned to fix or establish key specifications for your application on your request. Please consult with your OMRON representative at any time to confirm actual specifications of purchased products. DIMENSIONS AND WEIGHTS Dimensions and weights are nominal and are not to be used for manufacturing purposes, even when tolerances are shown. ERRORS AND OMISSIONS The information in this document has been carefully checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical, or proofreading errors, or omissions. PROGRAMMABLE PRODUCTS OMRON shall not be responsible for the user s prograing of a prograable product, or any consequence thereof. COPYRIGHT AND COPY PERMISSION This document shall not be copied for sales or promotions without permission. This document is protected by copyright and is intended solely for use in conjunction with the product. Please notify us before copying or reproducing this document in any manner, for any other purpose. If copying or transmitting this document to another, please copy or transmit it in its entirety. OMRON shall not be responsible for conformity with any standards, codes, or regulations that apply to the combination of products in the customer s application or use of the product. At the customer s request, OMRON will provide applicable third party certification documents identifying ratings and limitations of use that apply to the products. This information by itself is not sufficient for a complete determination of the suitability of the products in combination with the end product, machine, system, or other application or use. The following are some examples of applications for which particular attention must be given. This is not intended to be an exhaustive list of all possible uses of the products, nor is it intended to imply that the uses listed may be suitable for the products: Outdoor use, uses involving potential chemical contamination or electrical interference, or conditions or uses not described in this document. Nuclear energy control systems, combustion systems, railroad systems, aviation systems, medical equipment, amusement machines, vehicles, safety equipment, and installations subject to separate industry or government regulations. Systems, machines, and equipment that could present a risk to life or property. Please know and observe all prohibitions of use applicable to the products. NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCT IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. A-9

10 Cat. No. D-E--X In the interest of product improvement, specifications are subject to change without notice. OMRON EUROPE B.V. Wegalaan 67-69, NL-3 JD, Hoofddorp, The Netherlands Phone: Fax: A- Inductive Proximity Sensor