KINO-780AM2. User Manual MODEL: Mini-ITX AMD Socket AM2 with VGA, DVI-I and HDMI Dual PCIe, USB 2.0, SATA II and Audio. Rev September, 2009

Transcription

1 IEI Technology Corp. MODEL: KINO-780AM2 Mini-ITX AMD Socket AM2 with VGA, DVI-I and HDMI Dual PCIe, USB 2.0, SATA II and Audio User Manual Rev September, 2009 Page i

2 Revision Date Version Changes 1 September, Initial release Page ii

3 Copyright COPYRIGHT NOTICE The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages. This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic, or other means in any form without prior written permission of the manufacturer. TRADEMARKS All registered trademarks and product names mentioned herein are used for identification purposes only and may be trademarks and/or registered trademarks of their respective owners. Page iii

4 Table of Contents 1 INTRODUCTION INTRODUCTION FEATURES CONNECTORS DIMENSIONS DATA FLOW TECHNICAL SPECIFICATIONS PACKING LIST ANTI-STATIC PRECAUTIONS UNPACKING PRECAUTIONS PACKING LIST OPTIONAL ITEMS CONNECTORS PERIPHERAL INTERFACE CONNECTORS Layout Peripheral Interface Connectors External Interface Panel Connectors INTERNAL PERIPHERAL CONNECTORS ATX Power Connector CPU Fan Connector CPU Power Connector Digital I/O Connector Front Panel Connector PCI Express x16 Slot SATA Drive Connectors SPDIF Connector SPI Flash Connector System Fan Connector TPM Connector Page iv

5 USB Connectors EXTERNAL PERIPHERAL INTERFACE CONNECTOR PANEL Audio Connector DVI Connector HDMI Connector Keyboard/Mouse Connector LAN and Dual USB Combo Connectors Serial Port Connector VGA Connector INSTALLATION ANTI-STATIC PRECAUTIONS INSTALLATION CONSIDERATIONS Installation Notices Installation Checklist CPU, CPU COOLING KIT AND DIMM INSTALLATION CPU Installation Cooling Kit Installation (Screw Type) Cooling Kit Installation (Clip Type) DIMM Installation JUMPER SETTINGS Clear CMOS Jumper CHASSIS INSTALLATION Airflow Motherboard Installation INTERNAL PERIPHERAL DEVICE CONNECTIONS PCIe x16 Expansion Card Installation SATA Drive Connection USB Cable (Four Port) EXTERNAL PERIPHERAL INTERFACE CONNECTION Audio Connection DVI Display Device Connection LAN Connection (Single Connector) PS/2 Keyboard and Mouse Connection Serial Device Connection Page v

6 4.7.6 USB Connection (Dual Connector) VGA Monitor Connection DRIVER INSTALLATION BIOS INTRODUCTION Starting Setup Using Setup Getting Help Unable to Reboot After Configuration Changes BIOS Menu Bar MAIN ADVANCED CPU Configuration IDE Configuration SATA Channel Super IO Configuration Hardware Health Configuration Power Configuration Remote Access Configuration USB Configuration USB Mass Storage Device Configuration PCI/PNP BOOT Boot Settings Configuration Boot Device Priority Hard Disk Drives Removable Drives CD/DVD Drives SECURITY CHIPSET Northbridge Configuration ECC Configuration Northbridge2 Configuration Southbridge Configuration Page vi

7 5.8 EXIT A BIOS OPTIONS B TERMINOLOGY C DIGITAL I/O INTERFACE C.1 INTRODUCTION C.2 DIO CONNECTOR PINOUTS C.3 ASSEMBLY LANGUAGE SAMPLES C.3.1 Enable the DIO Input Function C.3.2 Enable the DIO Output Function D WATCHDOG TIMER E HAZARDOUS MATERIALS DISCLOSURE E.1 HAZARDOUS MATERIALS DISCLOSURE TABLE FOR IPB PRODUCTS CERTIFIED AS ROHS COMPLIANT UNDER 2002/95/EC WITHOUT MERCURY Page vii

8 List of Figures Figure 1 1: KINO-780AM2...2 Figure 1-2: KINO-780AM2 Overview...3 Figure 1-3: KINO-780AM2 Dimensions (mm)...4 Figure 1-4: Data Flow Block Diagram...5 Figure 3-1: Connector and Jumper Locations...13 Figure 3-2: ATX Power Connector Pinout Locations...15 Figure 3-3: CPU Fan Connector Location...16 Figure 3-4: CPU Power Connector Location...17 Figure 3-5: DIO Connector Locations...18 Figure 3-6: Front Panel Connector Location...19 Figure 3-7: PCIe x16 Slot Location...20 Figure 3-8: SATA Drive Connector Locations...20 Figure 3-9: SPDIF Connector Pinout Locations...21 Figure 3-10: SPI Flash Connector Location...22 Figure 3-11: System Fan Connector Location...23 Figure 3-12: TPM Connector Pinout Locations...24 Figure 3-13: USB Connector Pinout Locations...25 Figure 3-14: KINO-780AM2 External Peripheral Interface Connector...26 Figure 3-15: Audio Connector...26 Figure 3-16: DVI-D Connector Pinouts...27 Figure 3-17: PS/2 Pinouts...29 Figure 3-18: RJ-45 Ethernet Connector...30 Figure 3-19: Serial Port Location...31 Figure 3-20: VGA Connector...32 Figure 4-1: Install the CPU...38 Figure 4-2: Cooling Kit...39 Figure 4-3: Securing the Heat sink to the PCB Board...40 Figure 4-4: Cooling Kit...40 Figure 4-5: Install the CPU cooler...41 Figure 4-6: Installing a DIMM...42 Page viii

9 Figure 4-7: Clear CMOS Jumper...44 Figure 4-8: PCIe x16 Installation...46 Figure 4-9: SATA Drive Cable Connection...47 Figure 4-10: SATA Power Drive Connection...48 Figure 4-11: Four Port USB Cable Connection...49 Figure 4-12: Audio Connectors...50 Figure 4-13: DVI Connector...51 Figure 4-14: LAN Connection...52 Figure 4-15: PS/2 Keyboard/Mouse Connector...53 Figure 4-16: Serial Device Connector...54 Figure 4-17: USB Connector...55 Figure 4-18: VGA Connector...56 Page ix

10 List of Tables Table 1-1: Technical Specifications...7 Table 2-1: Package List Contents...11 Table 2-2: Package List Contents...11 Table 3-1: Peripheral Interface Connectors...14 Table 3-2: Rear Panel Connectors...15 Table 3-3: ATX Power Connector Pinouts...16 Table 3-4: CPU Fan Connector Pinouts...17 Table 3-5: CPU Power Connector Pinouts...17 Table 3-6: DIO Connector Pinouts...18 Table 3-7: Front Panel Connector Pinouts...19 Table 3-8: SATA Drive Connector Pinouts...21 Table 3-9: SPDIF Connector Pinouts...21 Table 3-10: SPI Flash Connector Pinouts...22 Table 3-11: System Fan Connector Pinouts...23 Table 3-12: TPM Connector Pinouts...24 Table 3-13: USB Port Connector Pinouts...25 Table 3-14: DVI-D Connector Pinouts...27 Table 3-15: HDMI Connector...28 Table 3-16: PS/2 Connector Pinouts...29 Table 3-17: LAN Pinouts...30 Table 3-18: RJ-45 Ethernet Connector LEDs...30 Table 3-19: USB Port Pinouts...31 Table 3-20: Serial Port Pinouts...31 Table 3-21: VGA Connector Pinouts...32 Table 4-1: Jumpers...43 Table 4-2: Clear CMOS Jumper Settings...44 Table 5-1: BIOS Navigation Keys...60 Page x

11 BIOS Menus BIOS Menu 1: Main...61 BIOS Menu 2: Advanced...63 BIOS Menu 3: CPU Configuration...63 BIOS Menu 4: IDE Configuration...67 BIOS Menu 5: IDE Master and IDE Slave Configuration...68 BIOS Menu 6: Super IO Configuration...72 BIOS Menu 7: Hardware Health Configuration...73 BIOS Menu 8: APM Configuration...74 BIOS Menu 9: Remote Access Configuration...77 BIOS Menu 10: USB Configuration...79 BIOS Menu 11: USB Mass Storage Device Configuration...80 BIOS Menu 12: PCI/PnP Configuration...82 BIOS Menu 13: Boot...84 BIOS Menu 14: Boot Settings Configuration...85 BIOS Menu 15: Boot Device Priority Settings...87 BIOS Menu 16: Hard Disk Drives...88 BIOS Menu 17: Removable Drives...88 BIOS Menu 18: CD/DVD Drives...89 BIOS Menu 19: Security...90 BIOS Menu 20: Chipset...91 BIOS Menu 21: Northbridge Configuration...92 BIOS Menu 22: ECC Configuration...92 BIOS Menu 23:Northbridge Chipset Configuration...97 BIOS Menu 24:Southbridge Chipset Configuration...98 BIOS Menu 25:Exit Page xi

12 Page xii KINO-780AM2 Motherboard

13 Chapter 1 1 Introduction Page 1

14 1.1 Introduction Figure 1 1: KINO-780AM2 The KINO-780AM2 Mini-ITX motherboard has a Socket AM2 CPU socket that supports a AMD Athlon 64, AMD Athlon 64 X2 or AMD Sempron processor. The board supports VGA, DVI and HDMI graphics output and a PCIe x16 graphics card. The integrated Radeon HD3200 graphics core provides hardware-based decoding for UVD, MPEG2 and H.264/AVC formats. The KINO-780AM2 supports two 2.0GB DDR2 SDRAM DIMMs with clock speeds of up to 800 MHz each. Expansion is provided by four SATA II ports, eight USB ports, a COM port and two PS/2 ports for a keyboard and mouse. 1.2 Features Some of the KINO-780AM2 features are listed below. Supports the following AMD Socket AM2/AM2+ processors: o AMD Athlon 64 o AMD Athlon 64 X2 o AMD Sempron Supports two 240-pin DDR2 DIMMs up to 800 MHz and 2.0 GB each Multiple graphics outputs o VGA o HDMI/DVI o PCIe x16 graphics card Four SATA II drives with transfer rates of 3.0 Gb/s supported Eight USB 2.0 devices supported One PCIe x16 graphics card supported Dual PCIe Gigabit Ethernet connectors Mini-ITX form factor RoHS compliant Page 2

15 1.3 Connectors All the connectors are shown in the diagram below. Figure 1-2: KINO-780AM2 Overview 1.4 Dimensions The dimensions of the board are listed below: Length: 305mm Width: 244mm Page 3

16 Figure 1-3: KINO-780AM2 Dimensions (mm) Page 4

17 1.5 Data Flow The diagram below shows the data flow between the chipsets and connectors on the board. Figure 1-4: Data Flow Block Diagram 1.6 Technical Specifications All the technical specifications are shown in the table below. Specification Form Factor KINO-780AM2 Mini-ITX System CPU AMD Athlon 64 AMD Athlon 64 X2 AMD Sempron Page 5

18 System Chipset Memory Super I/O Display Interface BIOS Audio LAN COM USB2.0 SATA Keyboard/mouse Expansion Digital I/O Watchdog Timer Power Supply Power Consumption Temperature Humidity (operating) Dimensions (LxW) Northbridge: AMD RS780E Southbridge: AMD SB710 Two 2.0GB DDR2 SDRAM DIMMs with clock speeds of up to 800 MHz each Fintek F71859 VGA DVI-D HDMI PCIe x16 graphics port AMI Flash BIOS Realtek ALC888 High Definition Audio chip Two Realtek RTL8111CP PCIe GbE chip One RS-232 serial port Eight USB 2.0 devices supported Four 3.0Gb/s SATA II drives supported Two PS/2 connectors One PCIe x16 slot One 8-bit digital input/output connector; 4-bit input/4-bit output Software programmable sec. by Fintek F75111R ATX power A A Vcore A A (AMD Phenom X CPU) 0ºC 60ºC (32ºF - 140ºF) 5%~95% non-condensing 170 mm x 170 mm Page 6

19 Weight (GW/NW) 1000 g / 450 g Table 1-1: Technical Specifications NOTE: Due to the limitation of Windows 32-bit operating system, when more than 4 GB of physical memory is installed, the actual memory available for the operating system is less than 4 GB. The Windows 64-bit operating system doesn't have such limitation. Page 7

20 Chapter 2 2 Packing List Page 8

21 2.1 Anti-static Precautions WARNING: Failure to take ESD precautions during the installation of the KINO-780AM2 may result in permanent damage to the KINO-780AM2 and severe injury to the user. Electrostatic discharge (ESD) can cause serious damage to electronic components, including the KINO-780AM2. Dry climates are especially susceptible to ESD. It is therefore critical that whenever the KINO-780AM2, or any other electrical component is handled, the following anti-static precautions are strictly adhered to. Wear an anti-static wristband: - Wearing a simple anti-static wristband can help to prevent ESD from damaging the board. Self-grounding:- Before handling the board touch any grounded conducting material. During the time the board is handled, frequently touch any conducting materials that are connected to the ground. Use an anti-static pad: When configuring the KINO-780AM2, place it on an antic-static pad. This reduces the possibility of ESD damaging the KINO-780AM2. Only handle the edges of the PCB: When handling the PCB, hold the PCB by the edges. 2.2 Unpacking Precautions When the KINO-780AM2 is unpacked, please do the following: Follow the anti-static precautions outlined in Section 2.1. Make sure the packing box is facing upwards so the KINO-780AM2 does not fall out of the box. Make sure all the packing list items are included. Page 9

22 2.3 Packing List NOTE: If some of the components listed in the checklist below are missing, please do not proceed with the installation. Contact the IEI reseller or vendor you purchased the KINO-780AM2 from or contact an IEI sales representative directly. To contact an IEI sales representative, please send an to The KINO-780AM2 is shipped with the following components: Quantity Item and Part Number Image 1 KINO-780AM2 1 I/O Shielding (P/N: C0-00-RS) 4 SATA cables (P/N: RS) 1 Mini jumper pack 1 Quick Installation Guide Page 10

23 Quantity Item and Part Number Image 1 Utility CD Table 2-1: Package List Contents 2.4 Optional Items Item and Part Number Image CPU cooler (up to 65 W) (P/N: CF-478D-RS) CPU cooler (up to 120 W) (P/N: CF-478E-RS) SATA power cable (P/N: RS) Dual USB cable (w bracket) (P/N: CB-USB02-RS) Winbond TPM module (P/N: TPM-WI01-R10) Infineon TPM module (P/N: TPM-IN01-R10) Table 2-2: Package List Contents Page 11

24 Chapter 3 3 Connectors Page 12

25 3.1 Peripheral Interface Connectors Section shows peripheral interface connector locations. Section 3.2 lists all the peripheral interface connectors seen in Section Layout Figure 3-1 shows the on-board peripheral connectors, rear panel peripheral connectors and on-board jumpers. Figure 3-1: Connector and Jumper Locations Page 13

26 3.1.2 Peripheral Interface Connectors Table 3-1 shows a list of the peripheral interface connectors on the KINO-780AM2. Detailed descriptions of these connectors can be found below. Connector Type Label ATX power connector 24-pin ATX ATX1 CPU cooling fan 4-pin wafer CPU_FAN1 CPU power connector 4-pin connector CPU12V4 Digital input/output connector 10-pin header DIO1 Front panel connector 14-pin header F_PANEL1 PCIe x16 expansion slot 164-pin PCIe slot PCIE1 Serial ATA drive connector 7-pin SATA S_ATA1, S_ATA2, S_ATA3, S_ATA4 SPDIF connector 5-pin header SPDIF1 SPI flash connector 8-pin header JSPI1 System fan connector 3-pin wafer SYS_FAN1 TPM connector 20-pin header TPM1 USB connector 8-pin header USB1, USB2 Table 3-1: Peripheral Interface Connectors External Interface Panel Connectors Table 3-2 lists the rear panel connectors on the KINO-780AM2. Detailed descriptions of these connectors can be found in Section Connector Type Label Audio connector Audio jack AUDIO_CV1 DVI connector DVI-D VIDEO1 HDMI connector HDMI HDMI1 Keyboard and mouse connector PS/2 KB_MS1 Page 14

27 Connector Type Label LAN connectors USB LAN1_USB1B, LAN2_USB2B Serial port connector DB-9 COM1 USB connectors USB LAN1_USB1B, LAN2_USB2B VGA connector DB-15 VIDEO1 Table 3-2: Rear Panel Connectors 3.2 Internal Peripheral Connectors Internal peripheral connectors are found on the motherboard and are only accessible when the motherboard is outside of the chassis. This section has complete descriptions of all the internal, peripheral connectors on the KINO-780AM ATX Power Connector CN Label: CN Type: ATX1 20-pin ATX (2x10) CN Location: See Figure 3-2 CN Pinouts: See Table 3-3 The ATX connector is connected to an external ATX power supply. Power is provided to the system, from the power supply through this connector. Figure 3-2: ATX Power Connector Pinout Locations Page 15

28 Pin Description Pin Description V V V 14-12V 3 GND 15 GND 4 +5V 16 PSON 5 GND 17 GND 6 +5V 18 GND 7 GND 19 GND 8 POK 20-5V(N/C) 9 5VSB 21 +5V V 22 +5V Table 3-3: ATX Power Connector Pinouts CPU Fan Connector CN Label: CN Type: CPU_FAN1 4-pin header CN Location: See Figure 3-3 CN Pinouts: See Table 3-4 Connects to the cooling fan on the CPU heatsink. Figure 3-3: CPU Fan Connector Location Pin Description 1 GND V 3 Rotation signal Page 16

29 Pin Description 4 PWM control signal Table 3-4: CPU Fan Connector Pinouts CPU Power Connector CN Label: CN Type: CPU12V4 4-pin connector CN Location: See Figure 3-4 CN Pinouts: See Table 3-5 Provides additional 12 V power for the CPU. Figure 3-4: CPU Power Connector Location Pin Description Pin Description 1 GND 2 GND V V Table 3-5: CPU Power Connector Pinouts Digital I/O Connector CN Label: CN Type: DIO1 10-pin header (2x5) CN Location: See Figure 3-5 CN Pinouts: See Table 3-6 Page 17

30 The digital input/output connector is managed through a Super I/O chip. The DIO connector pins are user programmable. Figure 3-5: DIO Connector Locations Pin Description Pin Description 1 GND 2 +5V 3 Output 3 4 Output 2 5 Output 1 6 Output 0 7 Input 3 8 Input 2 9 Input 1 10 Input 0 Table 3-6: DIO Connector Pinouts Front Panel Connector CN Label: CN Type: F_PANEL1 14-pin header (2x7) CN Location: See Figure 3-6 CN Pinouts: See Table 3-7 The front panel connector connects to external switches and indicators to monitor and controls the motherboard. These indicators and switches include: Page 18

31 Figure 3-6: Front Panel Connector Location Pin Description 1 NC 2 Power + 3 Power - 4 Hard drive LED + 5 Hard drive LED - 6 Power LED + 7 Power LED + 8 Power LED - 9 Reset + 10 Reset - Table 3-7: Front Panel Connector Pinouts PCI Express x16 Slot CN Label: CN Type: CONN1 PCIe x16 slot CN Location: See Figure 3-7 This slot is for installing a PCIe x16 graphics card. Page 19

32 Figure 3-7: PCIe x16 Slot Location SATA Drive Connectors CN Label: CN Type: S_ATA1, S_ATA2, S_ATA3, and S_ATA4 7-pin SATA drive connectors CN Location: See Figure 3-8 CN Pinouts: See Table 3-8 The SATA drive connectors are each connected to SATA drives. The SATA connectors support up to 3.0 Gb/s transfer. Figure 3-8: SATA Drive Connector Locations Pin Description 1 GND 2 TX+ 3 TX- Page 20

33 Pin Description 4 GND 5 RX- 6 RX+ 7 GND Table 3-8: SATA Drive Connector Pinouts SPDIF Connector CN Label: CN Type: SPDIF1 5-pin header CN Location: See Figure 3-9 CN Pinouts: See Table 3-9 Use the SPDIF connector to connect digital audio devices to the system. Figure 3-9: SPDIF Connector Pinout Locations Pin Description 1 VCC 2 NC 3 SPDIF out 4 GND 5 SPDIF in Table 3-9: SPDIF Connector Pinouts Page 21

34 3.2.9 SPI Flash Connector CN Label: CN Type: JSPI1 8-pin header (2x4) CN Location: See Figure 3-10 CN Pinouts: See Table 3-10 The 8-pin SPI Flash connector is used to flash the BIOS. Figure 3-10: SPI Flash Connector Location Pin Description Pin Description 1 VDD 2 VSS 3 CS# 4 SCK 5 SO 6 SI 7 N/C 8 N/C Table 3-10: SPI Flash Connector Pinouts System Fan Connector CN Label: CN Type: SYS_FAN1 3-pin header CN Location: See Figure 3-11 CN Pinouts: See Table 3-11 Page 22

35 Connects to the system cooling fan. Figure 3-11: System Fan Connector Location Pin Description 1 Rotation signal V 3 GND Table 3-11: System Fan Connector Pinouts TPM Connector CN Label: CN Type: TPM1 20-pin header (2x10) CN Location: See Figure 3-12 CN Pinouts: See Table 3-12 The Trusted Platform Module (TPM) connector secures the system on bootup. Page 23

36 Figure 3-12: TPM Connector Pinout Locations Pin Description Pin Description 1 LCLK 2 GND2 3 LFRAME# 4 KEY 5 LRESET# 6 +5 V 7 LAD3 8 LAD V 10 LAD1 11 LAD0 12 GND3 13 SCL 14 SDA 15 SB3 V 16 SERIRQ 17 GND1 18 GLKRUN# 19 LPCPD# 20 LDRQ# Table 3-12: TPM Connector Pinouts USB Connectors CN Label: CN Type: USB1 and USB2 8-pin header (2x4) CN Location: See Figure 3-13 CN Pinouts: See Table 3-13 The USB connectors connect to USB devices. Each pin header provides two USB ports. Page 24

37 Figure 3-13: USB Connector Pinout Locations Pin Description Pin Description 1 VCC 2 GND 3 DATAN- 4 DATA1M+ 5 DATAN+ 6 DATAM- 7 GND 8 VCC Table 3-13: USB Port Connector Pinouts 3.3 External Peripheral Interface Connector Panel Figure 3-14 shows the KINO-780AM2 external peripheral interface connector panel. Page 25

38 Figure 3-14: KINO-780AM2 External Peripheral Interface Connector Audio Connector CN Label: CN Type: AUDIO_CV1 2 x audio jacks CN Location: See Figure 3-14 The three audio jacks on the external audio connector enable the KINO-780AM2 to be connected to external audio devices as specified below. Line Out port (Lime): Connects to a headphone or a speaker. With multi-channel configurations, this port can also connect to front speakers. Microphone (Pink): Connects a microphone. Figure 3-15: Audio Connector Page 26

39 3.3.2 DVI Connector CN Label: CN Type: VIDEO1 DVI-D CN Location: See Figure 3-14 CN Pinouts: See Table 3-14 and Figure 3-16 Connects to a display that accepts DVI video input. Figure 3-16: DVI-D Connector Pinouts Pin Description Pin Description Pin Description 1 TMDS Data2-9 TMDS Data1-17 TMDS Data0-2 TMDS Data2+ 10 TMDS Data1+ 18 TMDS Data0+ 3 GND 11 GND 19 GND 4 N/C 12 NC 20 NC 5 N/C 13 NC 21 NC 6 DDC Clock [SCL] 14 PVDD1 22 GND 7 DDC Data [SDA] 15 GND 23 TMDS Clock + 8 Analog vertical sync 16 GND 24 TMDS Clock - C1 N/C C2 N/C C3 N/C C4 N/C C5 N/C Table 3-14: DVI-D Connector Pinouts HDMI Connector CN Label: HDMI1 Page 27

40 CN Type: HDMI connector CN Location: See Figure 3-14 CN Pinouts: See Table 3-15 Connects to a screen or device that accepts HDMI video input. Pin Description Pin Description 1 HDMI_DATA2 13 N/C 2 GND 14 N/C 3 HDMI_DATA2# 15 HDMI_SCL 4 HDMI_DATA1 16 HDMI_SDA 5 GND 17 GND 6 HDMI_DATA1# 18 +5V 7 HDMI_DATA0 19 HDMI_HPD 8 GND 20 HDMI_GND 9 HDMI_DATA0# 21 HDMI_GND 10 HDMI_CLK 22 HDMI_GND 11 GND 23 HDMI_GND 12 HDMI_CLK# Table 3-15: HDMI Connector Keyboard/Mouse Connector CN Label: CN Type: KB_MS1 Dual PS/2 CN Location: See Figure 3-14 CN Pinouts: See Figure 3-17 and Table 3-16 The KINO-780AM2 keyboard and mouse connectors are standard PS/2 connectors. Page 28

41 Figure 3-17: PS/2 Pinouts Pin Description 1 Keyboard data 2 NC 3 GND 4 VCC 5 Keyboard clock 6 NC 7 Mouse data 8 NC 9 GND 10 VCC 11 Mouse clock 12 NC Table 3-16: PS/2 Connector Pinouts LAN and Dual USB Combo Connectors CN Label: CN Type: LAN1_USB1B and LAN2_USB2B RJ-45 and two USB CN Location: See Figure 3-14 CN Pinouts: See Table 3-17 and Table 3-19 Page 29

42 The KINO-780AM2 is equipped with two built-in RJ-45 GbE controllers. The controllers can connect to the LAN through two RJ-45 LAN connectors. There are two LEDs on the connector indicating the status of LAN. The pin assignments are listed in the following table: Pin Description Pin Description 1 X0+ 2 X0-3 X1+ 4 X2+ 5 X2-6 X1-7 X3+ 8 X3- Table 3-17: LAN Pinouts Figure 3-18: RJ-45 Ethernet Connector The RJ-45 Ethernet connector has two status LEDs, one green and one yellow. The green LED indicates activity on the port and the yellow LED indicates the port is linked. See Table STATUS DESCRIPTION STATUS DESCRIPTION Orange GbE Lan Yellow Activity Green 10/100 Lan Table 3-18: RJ-45 Ethernet Connector LEDs The KINO-780AM2 has four external USB 2.0 ports. The ports are integrated into two dual USB and LAN combo connectors. The USB ports connect to both USB 2.0 and USB 1.1 devices. Pin Description 1 USBVCC 2 DATA- 3 DATA+ Page 30

43 Pin Description 4 USBGND Table 3-19: USB Port Pinouts Serial Port Connector CN Label: CN Type: COM1 DB-9 connectors CN Location: See Figure 3-14 CN Pinouts: See Table 3-20 and Figure 3-19 Connects to an RS-232 device or network. Pin Description Pin Description 1 DCD 6 DSR 2 RX 7 RTS 3 TX 8 CTS 4 DTR 9 RI 5 GND Table 3-20: Serial Port Pinouts Figure 3-19: Serial Port Location VGA Connector CN Label: CN Type: VIDEO1 DB-15 CN Location: See Figure 3-14 Page 31

44 CN Pinouts: See Table 3-21 and Figure 3-20 The female DB-15 VGA connector connects to standard VGA displays. The connector and pinouts are shown below. Figure 3-20: VGA Connector Pin Description Pin Description 1 RED 2 GREEN 3 BLUE 4 NC 5 GND 6 GND 7 GND 8 GND 9 VCC / NC 10 GND 11 NC 12 DDC DAT 13 HSYNC 14 VSYNC 15 DDCCLK Table 3-21: VGA Connector Pinouts Page 32

45 Chapter 4 4 Installation Page 33

46 4.1 Anti-static Precautions WARNING: Failure to take ESD precautions during the installation of the KINO-780AM2 may result in permanent damage to the KINO-780AM2 and severe injury to the user. Electrostatic discharge (ESD) can cause serious damage to electronic components, including the KINO-780AM2. Dry climates are especially susceptible to ESD. It is therefore critical that whenever the KINO-780AM2, or any other electrical component is handled, the following anti-static precautions are strictly adhered to. Wear an anti-static wristband: - Wearing a simple anti-static wristband can help to prevent ESD from damaging the board. Self-grounding:- Before handling the board touch any grounded conducting material. During the time the board is handled, frequently touch any conducting materials that are connected to the ground. Use an anti-static pad: When configuring the KINO-780AM2, place it on an antic-static pad. This reduces the possibility of ESD damaging the KINO-780AM2. Only handle the edges of the PCB:- When handling the PCB, hold the PCB by the edges. Page 34

47 4.2 Installation Considerations NOTE: The following installation notices and installation considerations should be read and understood before the KINO-780AM2 is installed. All installation notices pertaining to the installation of the KINO-780AM2 should be strictly adhered to. Failing to adhere to these precautions may lead to severe damage of the KINO-780AM2 and injury to the person installing the motherboard Installation Notices WARNING: The installation instructions described in this manual should be carefully followed in order to prevent damage to the KINO-780AM2, KINO-780AM2 components and injury to the user. Before and during the installation please DO the following: Read the user manual: o The user manual provides a complete description of the KINO-780AM2 installation instructions and configuration options. Wear an electrostatic discharge cuff (ESD): o Electronic components are easily damaged by ESD. Wearing an ESD cuff removes ESD from the body and helps prevent ESD damage. Place the KINO-780AM2 on an antistatic pad: o When installing or configuring the motherboard, place it on an antistatic pad. This helps to prevent potential ESD damage. Turn all power to the KINO-780AM2 off: o When working with the KINO-780AM2, make sure that it is disconnected from all power supplies and that no electricity is being fed into the system. Page 35

48 Before and during the installation of the KINO-780AM2 DO NOT: Remove any of the stickers on the PCB board. These stickers are required for warranty validation. Use the product before verifying all the cables and power connectors are properly connected. Allow screws to come in contact with the PCB circuit, connector pins, or its components Installation Checklist The following checklist is provided to ensure the KINO-780AM2 is properly installed. All the items in the packing list are present The CPU is installed The CPU cooling kit is properly installed A compatible memory module is properly inserted into the slot The jumpers have been properly configured The KINO-780AM2 is inserted into a chassis with adequate ventilation The correct power supply is being used The following devices are properly connected o SATA drives o Keyboard and mouse cable o Audio kit o Power supply o USB cable o Serial port cable The following external peripheral devices are properly connected to the chassis: o Screen o Keyboard o Mouse o LAN o VGA screen Page 36

49 4.3 CPU, CPU Cooling Kit and DIMM Installation WARNING: A CPU should never be turned on without the specified cooling kit being installed. If the cooling kit (heat sink and fan) is not properly installed and the system turned on, permanent damage to the CPU, KINO-780AM2 and other electronic components attached to the system may be incurred. Running a CPU without a cooling kit may also result in injury to the user. The CPU, CPU cooling kit and DIMM are the most critical components of the KINO-780AM2. If one of these components is not installed the KINO-780AM2 cannot run CPU Installation WARNING: CPUs are expensive and sensitive components. When installing the CPU please be careful not to damage it in anyway. Make sure the CPU is installed properly and ensure the correct cooling kit is properly installed. To install a socket AM2 CPU onto the KINO-780AM2, follow the steps below: WARNING: When handling the CPU, only hold it on the sides. DO NOT touch the pins at the bottom of the CPU. Page 37

50 Step 1: Inspect the CPU socket. Make sure there are no bent pins and make sure the socket contacts are free of foreign material. If any debris is found, remove it with compressed air. Step 2: Open the CPU socket lever. Disengage the load lever by moving the lever slightly outward to clear the retention tab. Rotate the load lever to a fully open position. See Figure 4-1. Step 3: Orientate the CPU properly. Make sure the IHS (Integrated Heat Sink) side is facing upward. See Figure 4-1. Step 4: Correctly position the CPU. Match the Pin 1 mark with the cut edge on the CPU socket. See Figure 4-1. Figure 4-1: Install the CPU Step 5: Insert the CPU. Gently insert the CPU into the socket. If the CPU pins are properly aligned, the CPU should slide into the CPU socket smoothly Step 6: Close the CPU socket. Re-engage the load lever by pushing it back to its original position. Secure the load lever under the retention tab on the side of CPU socket. Step 0: Page 38

51 4.3.2 Cooling Kit Installation (Screw Type) Figure 4-2: Cooling Kit The cooling kit can be bought from IEI. The cooling kit has a heatsink and fan. WARNING: Do not wipe off (accidentally or otherwise) the pre-sprayed layer of thermal paste on the bottom of the heat sink. The thermal paste between the CPU and the heat sink is important for optimum heat dissipation. To install the cooling kit, follow the instructions below. Step 1: Place the cooling kit onto the socket. Make sure the CPU cable can be properly routed when the cooling kit is installed. Step 2: Properly align the cooling kit. Make sure the four spring screw fasteners can pass through the pre-drilled holes on the PCB. Step 3: Mount the cooling kit. Gently place the cooling kit on top of the CPU. Make sure the four threaded screws on the corners of the cooling kit properly pass through the predrilled holes on the bottom of the PCB. Step 4: Secure the cooling kit. From the solder side of the PCB, align the support bracket to the screw threads on heat sink that were inserted through the PCB holes. (See Figure 4-3) Page 39

52 Figure 4-3: Securing the Heat sink to the PCB Board Step 5: Tighten the screws. Use a screwdriver to tighten the four screws. Tighten each nut a few turns at a time and do not over-tighten the screws. Step 6: Connect the fan cable. Connect the cooling kit fan cable to the fan connector on the KINO-780AM2. Carefully route the cable and avoid heat generating chips and fan blades. Step 6: Cooling Kit Installation (Clip Type) Figure 4-4: Cooling Kit A cooling kit can be purchased separately. The cooling kit comprises a CPU heat sink and a cooling fan. To install the cooling kit, please follow the steps below. Page 40

53 Step 7: Spread a proper amount of thermal paste onto the bottom of the cooling fan heat sink. The thermal paste between the CPU and the heat sink is important for optimum heat dissipation. Step 8: Properly orient the cooling kit. Be sure the cooling kit is properly oriented before installing the cooling kit into the preinstalled cooling kit bracket. Step 9: Install the cooling kit into the preinstalled cooling kit bracket. See Figure 4-5. Step 10: Attach the levered mounting clips. Slip the four levered mounting clips into the clip holes on the cooling kit bracket. See Figure 4-5. Step 11: Secure the cooling kit in place. Gently push the plastic mounting clip down to lock the cooling kit. See Figure 4-5. Figure 4-5: Install the CPU cooler Step 12: Connect the fan cable. Connect the cooling kit fan cable to the fan connector on the CPU card. Carefully route the cable and avoid heat generating chips and fan blades.step 0: Page 41

54 4.3.4 DIMM Installation WARNING: Using incorrectly specified DIMM may cause permanently damage the KINO-780AM2. Please make sure the purchased DIMM complies with the memory specifications of the KINO-780AM2. DIMM specifications compliant with the KINO-780AM2 are listed in Chapter 2. To install a DIMM into a DIMM socket, please follow the steps below and refer to Figure 4-6. Figure 4-6: Installing a DIMM Step 1: Open the DIMM socket handles. The DIMM socket has two handles that secure the DIMM into the socket. Before the DIMM can be inserted into the socket, the handles must be opened. See Figure 4-6. Step 2: Align the DIMM with the socket. The DIMM must be oriented in such a way that the notch in the middle of the DIMM must be aligned with the plastic bridge in the socket. See Figure 4-6. Page 42

55 Step 3: Insert the DIMM. Once properly aligned, the DIMM can be inserted into the socket. As the DIMM is inserted, the white handles on the side of the socket will close automatically and secure the DIMM to the socket. See Figure 4-6. Step 4: Removing a DIMM. To remove a DIMM, push both handles outward. The memory module is ejected by a mechanism in the socket.step 0: 4.4 Jumper Settings NOTE: A jumper is a metal bridge that is used to close an electrical circuit. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To CLOSE/SHORT a jumper means connecting the pins of the jumper with the plastic clip and to OPEN a jumper means removing the plastic clip from a jumper. Before the KINO-780AM2 is installed in the system, the jumpers must be set in accordance with the desired configuration. The jumpers on the KINO-780AM2 are listed in Table 4-1. Description Label Type Clear CMOS J_CMOS1 3-pin header Table 4-1: Jumpers Clear CMOS Jumper Jumper Label: Jumper Type: J_CMOS1 3-pin header Jumper Settings: See Table 4-2 Jumper Location: See Figure 4-7 Page 43

56 If the KINO-780AM2 fails to boot due to improper BIOS settings, the clear CMOS jumper clears the CMOS data and resets the system BIOS information. To do this, use the jumper cap to close pins 2 and 3 for a few seconds then reinstall the jumper clip back to pins 1 and 2. If the CMOS Settings Wrong message is displayed during the boot up process, the fault may be corrected by pressing the F1 to enter the CMOS Setup menu. Do one of the following: Enter the correct CMOS setting Load Optimal Defaults Load Failsafe Defaults. After having done one of the above, save the changes and exit the CMOS Setup menu. The clear CMOS jumper settings are shown in Table 4-2. Jumper Select Short 1-2 Short 2-3 Description Normal operation Clear CMOS Setup Table 4-2: Clear CMOS Jumper Settings The location of the clear CMOS jumper is shown in Figure 4-7 below. Figure 4-7: Clear CMOS Jumper Page 44

57 4.5 Chassis Installation Airflow WARNING: Airflow is critical to the cooling of the CPU and other onboard components. The chassis in which the KINO-780AM2 must have air vents to allow cool air to move into the system and hot air to move out. The KINO-780AM2 must be installed in a chassis with ventilation holes on the sides allowing airflow to travel through the heat sink surface. In a system with an individual power supply unit, the cooling fan of a power supply can also help generate airflow through the board surface Motherboard Installation To install the KINO-780AM2 motherboard into the chassis please refer to the reference material that came with the chassis. 4.6 Internal Peripheral Device Connections This section outlines the installation of external components to the motherboard. Cables included in the package are listed in the unpacking section PCIe x16 Expansion Card Installation A PCIe x16 expansion card can be installed on the KINO-780AM2 using the PCIe x16 expansion slot. To install a PCIe expansion card into the PCIe socket, please follow the steps below. Page 45

58 Figure 4-8: PCIe x16 Installation Step 1: Locate the PCIe x16 socket. Place the KINO-780AM2 on an anti-static pad with the solder side facing up. Step 2: Align the PCIe x16 card with the socket. The PCIe x16 card must be aligned so the notch on the PCIe x16 card aligns with the plastic bridge in the socket. Step 3: Insert the PCIe x16 card. Push the PCIe x16 card into the socket, perpendicular to the KINO-780AM2. Step 4: Secure the PCI x16 card. Push the PCIe x16 card down until the clip engages, securing the card in place. Step 0: SATA Drive Connection The KINO-780AM2 is shipped with two SATA drive cables and one SATA drive power cable. To connect the SATA drives to the connectors, please follow the steps below. Step 1: Locate the connectors. The locations of the SATA drive connectors are shown in Chapter 3. Page 46

59 Step 2: Insert the cable connector. Press the clip on the connector at the end of the SATA cable and insert the cable connector into the onboard SATA drive connector. See Figure 4-9. Figure 4-9: SATA Drive Cable Connection Step 3: Connect the cable to the SATA disk. Connect the connector on the other end of the cable to the connector at the back of the SATA drive. See Figure Step 4: Connect the SATA power cable. Connect the SATA power connector to the back of the SATA drive. See Figure Step 4: Page 47

60 Figure 4-10: SATA Power Drive Connection USB Cable (Four Port) Four port USB 2.0 cables can be separately purchased from IEI. To install a four port USB cable onto the KINO-780AM2, please follow the steps below. Step 5: Locate the connectors. The locations of the USB connectors are shown in Chapter 4. WARNING: If the USB pins are not properly aligned, the USB device can burn out. Step 6: Align the connectors. Each cable has two connectors. Correctly align pin 1on each cable connector with pin 1 on the KINO-780AM2 USB connectors. Step 7: Insert the cable connectors. Once the cable connectors are properly aligned with the USB connectors on the KINO-780AM2, connect the cable connectors to the onboard connectors. See Figure Page 48

61 Figure 4-11: Four Port USB Cable Connection Step 8: Attach the bracket to the chassis. The USB 2.0 connectors are attached to a bracket. To secure the bracket to the chassis please refer to the installation instructions that came with the chassis.step 0: 4.7 External Peripheral Interface Connection The connection of external devices to the external connectors are outlined in the subsections below Audio Connection Audio signals are interfaced through three phone jack connections. The red phone jack is for Mic In, blue is for Line In and green is for Speaker Out. Follow the steps below to connect audio devices to the KINO-780AM2. Step 1: Locate the audio phone jacks. The location of the audio phone jacks are shown in Chapter 3. Step 2: Insert audio phone jack plugs. Insert audio phone jack plugs into the audio phone jacks on the external peripheral interface. See Figure Step 2: Page 49

62 Figure 4-12: Audio Connectors DVI Display Device Connection The KINO-780AM2 has a single female DVI connector on the external peripheral interface panel. The DVI connector is connected to a digital display device. To connect a digital display device to the KINO-780AM2, please follow the instructions below. Step 3: Locate the DVI connector. The location of the DVI connector is shown in Chapter 2. Step 4: Align the DVI connector. Align the male DVI connector on the digital display device cable with the female DVI connector on the external peripheral interface. Step 5: Insert the DVI connector. Once the connectors are properly aligned with the male connector, insert the male connector from the digital display device into the female connector on the KINO-780AM2. See Figure Page 50

63 Figure 4-13: DVI Connector Step 6: Secure the connector. Secure the DVI connector from the digital display device to the external interface by tightening the two retention screws on either side of the connector. Step 0: LAN Connection (Single Connector) There are two external RJ-45 LAN connectors. The RJ-45 connectors enable connection to an external network. To connect a LAN cable with an RJ-45 connector, please follow the instructions below. Step 1: Locate the RJ-45 connectors. The locations of the USB connectors are shown in Chapter 4. Step 2: Align the connectors. Align the RJ-45 connector on the LAN cable with one of the RJ-45 connectors on the KINO-780AM2. See Figure Page 51

64 Figure 4-14: LAN Connection Step 3: Insert the LAN cable RJ-45 connector. Once aligned, gently insert the LAN cable RJ-45 connector into the onboard RJ-45 connector. Step 0: PS/2 Keyboard and Mouse Connection The KINO-780AM2 has a dual PS/2 connector on the external peripheral interface panel. The dual PS/2 connector is used to connect to a keyboard and mouse to the system. Follow the steps below to connect a keyboard and mouse to the KINO-780AM2. Step 1: Locate the dual PS/2 connector. The location of the dual PS/2 connector is shown in Chapter 3. Step 2: Insert the keyboard/mouse connector. Insert a PS/2 keyboard or mouse connector into the appropriate PS/2 connector on the external peripheral interface connector. See Figure Step 2: Page 52

65 Figure 4-15: PS/2 Keyboard/Mouse Connector Serial Device Connection The KINO-780AM2 has a single female DB-9 connector on the external peripheral interface panel for a serial device. Follow the steps below to connect a serial device to the KINO-780AM2. Step 3: Locate the DB-9 connector. The location of the DB-9 connector is shown in Chapter 3. Step 4: Insert the serial connector. Insert the DB-9 connector of a serial device into the DB-9 connector on the external peripheral interface. See Figure Page 53

66 Figure 4-16: Serial Device Connector Step 5: Secure the connector. Secure the serial device connector to the external interface by tightening the two retention screws on either side of the connector.step 0: USB Connection (Dual Connector) The external USB Series "A" receptacle connectors provide easier and quicker access to external USB devices. Follow the steps below to connect USB devices to the KINO-780AM2. Step 1: Locate the USB Series "A" receptacle connectors. The location of the USB Series "A" receptacle connectors are shown in Chapter 3. Step 2: Insert a USB Series "A" plug. Insert the USB Series "A" plug of a device into the USB Series "A" receptacle on the external peripheral interface. See Figure Step 2: Page 54

67 Figure 4-17: USB Connector VGA Monitor Connection The KINO-780AM2 has a single female DB-15 connector on the external peripheral interface panel. The DB-15 connector is connected to a CRT or VGA monitor. To connect a monitor to the KINO-780AM2, please follow the instructions below. Step 3: Locate the female DB-15 connector. The location of the female DB-15 connector is shown in Chapter 3. Step 4: Align the VGA connector. Align the male DB-15 connector on the VGA screen cable with the female DB-15 connector on the external peripheral interface. Step 5: Insert the VGA connector. Once the connectors are properly aligned with the insert the male connector from the VGA screen into the female connector on the KINO-780AM2. See Figure Page 55

68 Figure 4-18: VGA Connector Step 6: Secure the connector. Secure the DB-15 VGA connector from the VGA monitor to the external interface by tightening the two retention screws on either side of the connector. Step 0: 4.8 Driver Installation All drivers are on the included CD. Refer to the instructions below to start the driver installation program. NOTE: The content of the CD may vary throughout the life cycle of the product and is subject to change without prior notice. Visit the IEI website or contact technical support for the latest updates. Step 1: Insert the CD into a CD drive connected to the system. Page 56

69 NOTE: If the system does not initiate the "autorun" program when the CD is inserted, click the Start button, select Run, then type X:\autorun.exe (where X:\ is the system CD drive) to access the IEI Driver CD main menu. Step 2: Select KINO-780AM2 from the drivers list. Step 3: Install each of the drivers shown in the menu. Step 0: Page 57

70 Chapter 5 5 BIOS Page 58

71 5.1 Introduction The BIOS is programmed onto the BIOS chip. The BIOS setup program allows changes to certain system settings. This chapter outlines the options that can be changed Starting Setup The AMI BIOS is activated when the computer is turned on. The setup program can be activated in one of two ways. 1. Press the DELETE key as soon as the system is turned on or 2. Press the DELETE key when the Press Del to enter SETUP message appears on the screen. 0. If the message disappears before the DELETE key is pressed, restart the computer and try again Using Setup Use the arrow keys to highlight items, press ENTER to select, use the PageUp and PageDown keys to change entries, press F1 for help and press ESC to quit. Navigation keys are shown in. Key Up arrow Down arrow Left arrow Right arrow Esc key Function Move to previous item Move to next item Move to the item on the left hand side Move to the item on the right hand side Main Menu Quit and not save changes into CMOS Status Page Setup Menu and Option Page Setup Menu -- Exit current page and return to Main Menu Page Up key Page Dn key F1 key Increase the numeric value or make changes Decrease the numeric value or make changes General help, only for Status Page Setup Menu and Option Page Setup Menu Page 59

72 Key F2 /F3 key F10 key Function Change color from total 16 colors. F2 to select color forward. Save all the CMOS changes, only for Main Menu Table 5-1: BIOS Navigation Keys Getting Help When F1 is pressed a small help window describing the appropriate keys to use and the possible selections for the highlighted item appears. To exit the Help Window press ESC or the F1 key again Unable to Reboot After Configuration Changes If the computer cannot boot after changes to the system configuration is made, CMOS defaults. Use the jumper described in Chapter BIOS Menu Bar The menu bar on top of the BIOS screen has the following main items: Main Changes the basic system configuration. Advanced Changes the advanced system settings. PCIPnP Changes the advanced PCI/PnP Settings Boot Changes the system boot configuration. Security Sets User and Supervisor Passwords. Chipset Changes the chipset settings. Power Changes power management settings. Exit Selects exit options and loads default settings The following sections completely describe the configuration options found in the menu items at the top of the BIOS screen and listed above. Page 60

73 5.2 Main The Main BIOS menu (BIOS Menu 1) appears when the BIOS Setup program is entered. The Main menu gives an overview of the basic system information. BIOS SETUP UTILITY Main Advanced PCIPNP Boot Security Chipset Exit System Overview AMIBIOS Version : Build Date :03/25/09 ID: :B139MT13 Processor AMD Athlon 64 X2 Dual Core Processor Speed :1800MHz Count :2 System Memory Size :768MB System Time [14:20:27] System Time [Thu 04/06/2009] Use [ENTER], [TAB] or [SHIFT-TAB] to select a field. Use [+] or [-] to configure system time. Select Screen Select Item Enter Go to SubScreen F1 General Help F10 Save and Exit ESC Exit v02.61 Copyright , American Megatrends, Inc. BIOS Menu 1: Main System Overview The System Overview lists a brief summary of different system components. The fields in System Overview cannot be changed. The items shown in the system overview include: AMI BIOS: Displays auto-detected BIOS information o Version: Current BIOS version o Build Date: Date the current BIOS version was made o ID: Installed BIOS ID Processor: Displays auto-detected CPU specifications o Type: Names the currently installed processor o Speed: Lists the processor speed o Count: The number of CPUs on the motherboard System Memory: Displays the auto-detected system memory. o Size: Lists memory size Page 61

74 The System Overview field also has two user configurable fields: System Time [xx:xx:xx] Use the System Time option to set the system time. Manually enter the hours, minutes and seconds. System Date [xx/xx/xx] Use the System Date option to set the system date. Manually enter the day, month and year. 5.3 Advanced Use the Advanced menu (BIOS Menu 2) to configure the CPU and peripheral devices through the following sub-menus: WARNING! Setting the wrong values in the sections below may cause the system to malfunction. Make sure that the settings made are compatible with the hardware. CPU Configuration (see Section 5.3.1) IDE Configuration (see Section 5.3.2) Super IO Configuration (see Section 5.3.3) Hardware Health Configuration (see Section 5.3.4) Power Configuration (see Section 5.3.5) Remote Access Configuration (see Section 5.3.6) USB Configuration (see Section 5.3.7) Page 62

75 BIOS SETUP UTILITY Main Advanced PCIPNP Boot Security Chipset Exit Advanced Settings WARNING: Setting wrong values in below sections may cause system to malfunction > CPU Configuration > IDE Configuration > SuperIO Configuration > Hardware Health Configuration > Power Configuration > Remote Access Configuration > USB Configuration Configure CPU Select Screen Select Item Enter Go to SubScreen F1 General Help F10 Save and Exit ESC Exit v02.61 Copyright , American Megatrends, Inc. BIOS Menu 2: Advanced CPU Configuration Use the CPU Configuration menu (BIOS Menu 3) to view detailed CPU specifications and configure the CPU. BIOS SETUP UTILITY Main Advanced PCIPNP Boot Security Chipset Exit CPU Configuration Module Version: AGESA Version: Physical Count: 1 Logical Count: 2 AMD Athlon 64 X2 Dual Core Processor Revision: F2 Cache L1: 256KB Cache L2: 1024KB Cache L3: N/A Speed: 1800MHz, NB Clk: N/A Current FSB Multiplier: 9x Maximum FSB Multiplier: 9x Able to Change Freq.: Yes ucode Patch Level: 0x62 Select Screen Select Item Enter Go to SubScreen F1 General Help F10 Save and Exit ESC Exit v02.61 Copyright , American Megatrends, Inc. BIOS Menu 3: CPU Configuration The CPU Configuration menu (BIOS Menu 3) lists the following CPU details: Page 63