DS6300 QUICK REFERENCE GUIDE

Size: px

Start display at page:

Download "DS6300 QUICK REFERENCE GUIDE"

Cecily Griffin
6 years ago
Views:

1 DS600 QUICK REFERENCE GUIDE

2 CONTENTS DS MASTER/SLAVE MODEL... DS PROFIBUS MODEL...8 DS ETHERNET MODEL... DS DEVICENET MODEL...8 DS XX OSCILLATING MIRROR MODEL... COMMON FEATURES...5 NOTE For further details on product installation, see the complete Reference Manual available on the configuration CD-ROM included with this product. SERVICES AND SUPPORT Datalogic provides several services as well as technical support through its website. Log on to and click on the links indicated for further information including: PRODUCTS Search through the links to arrive at your product page where you can download specific Manuals and Software & Utilities including: - Genius a utility program, which allows device configuration using a PC. It provides RS interface configuration. SERVICES & SUPPORT - Datalogic Services - Warranty Extensions and Maintenance Agreements - Authorised Repair Centres CONTACT US form and listing of Datalogic Subsidiaries

DS600 MASTER/SLAVE MODEL DS600-00-00 MASTER/SLAVE MODEL Figure A Laser Beam Output Window 5 Figure B Figure C Programming Keypad Power On LED (Red) Main/Aux.

3 DS600 MASTER/SLAVE MODEL DS MASTER/SLAVE MODEL Figure A Laser Beam Output Window 5 Figure B Figure C Programming Keypad Power On LED (Red) Main/Aux. Interface 5-pin D-sub Male Connector TX Data LED (Green) 5 LCD Display Lonworks 9-pin Male Connector Phase On LED (Yellow) Lonworks 9-pin Female Connector Available Models: Optical Model 0 = Standard 5 = Oscillating Mirror DS600-0X - 0YY Decoder Model 0 = Master/Slave = Profibus = Ethernet 5 = Devicenet Technical Features: ELECTRICAL FEATURES OPTICAL FEATURES Supply Voltage 5-0 Vdc Light Receiver Avalanche photodiode Power Consumption 5 W typical 0 W Max. (including startup current) Wavelength 60 to 680 nm Safety Class Class -EN 6085-; Class II-CDRH Communication Main (isolated) Baud Rate Interfaces RS Laser Control Security system to turn laser RS85 full-duplex 00 to 500 off in case of motor slow down RS85 half-duplex READING FEATURES 0 ma C.L. (INT-0 with C-BOX 00 only) 900 Scan Rate scans/s Auxiliary Max. Resolution RS 00 to 50 Max. Read. Distance Other Max. Read. Width (see reading diagram) Lonworks.5 Mb/s Max. Depth of Field Inputs Ext. Trigger, aux. digital (optocoupled NPN or PNP) USER INTERFACE inputs LCD Display lines by 6 characters LCD Outputs Keypad keys software LED Indicators Power ON (red) programmable (optocoupled) Phase ON (yellow) digital outputs TX Data (green)

4 DS600 MASTER/SLAVE MODEL SOFTWARE FEATURES ENVIRONMENTAL FEATURES Readable Codes Interleaved /5 Operating 0 to +0 C Code 9 standard Temperature (+ to +0 F) Codabar -0 to +70 C Storage Temperature Code 8 (- to +58 F) EAN 8 Humidity 90% non condensing Code 9 (Standard & Full ASCII) Ambient Light EAN/UPC (including Add-on and Immunity 500 lux Add-on 5) Vibration Resistance to 0Hz Code Selection Up to 0 codes during one reading IEC test FC.5 to 55 Hz phase 70 to 00 Hz hours on each axis Headers and Up to 8-byte headers and8- Shock Resistance 0 g; ms Terminators byte terminators IEC test EA shocks on each axis Operating Protection Class IP6 On Line, Automatic, Test Modes Config. Mode Genius utility program Param. Storage Non-volatile internal FLASH PHYSICAL FEATURES Std Models Oscill. Mirror Dimensions mm (inch) 0xx99 (.x.5x.9) x80x0.5 (.5x7.08x.) Weight.5 kg (. lb).0 kg (. lb) Accessories: Name Description Part Number CAB-600 Cable to C-BOX00 m 9A0590 CAB-600 Cable to C-BOX00 m 9A0500 CAB-6005 Cable to C-BOX00 5 m 9A050 CAB-600 Cable to C-BOX00 0 m 9A057 CAB-60 Cable master/slave m 9A050 CAB-60 Cable master/slave m 9A050 CAB-605 Cable master/slave 5 m 9A050 CAB-6 Cable master/slave no power m 9A05 CAB-65 Cable master/slave no power 5 m 9A055 CAB-605 Power cable Fam 6k 5 m 9ACC768 CAB-60 Power cable Fam 6k 0 m 9ACC75 C-BOX 00 Passive connection box 9ACC50 INT-0 0 ma C.L. interface board for C-BOX 00 9A50 GFC mirror 9A000 GFC mirror close distance 9A00 GFX-60 X-pattern mirror 9ACC70 PWR-0 Power unit 0/0 V AC - V DC 9ACC50 BTK-6000 Terminator kit (5 pcs) 9ACC70 PG600 Single unit power supply US 9ACC78 PG600 Single unit power supply UK 9ACC79 PG6000 Single unit power supply EU 9ACC70 FBK-6000 Fast bracket kit ( pcs) 9ACC7 US-60 Mounting bracket kit (5 pcs) for multisided stations 9ACC79 PH- Photocell kit - PNP 9ACC79 MEP-5 Photocell kit - NPN 9ACC78 OEK- Optical encoder (0 m cable + spring) 9ACC770 OEK- Optical encoder kit + 0 m cable 9ACC600 Electrical Connections: The DS600 reader provides a 5-pin male D-sub connector for connection to power supply, Host interface (Main and Aux), and input/output signals. Two 9-pin connectors provide access to the scanner s local Lonworks network used for both input and output connections to build a multi-sided or omni-station system.

5 DS600 MASTER/SLAVE MODEL The details of the connector pins are indicated in the following table: 5-pin D-Sub Connector Pinout Pin Name Function CHASSIS Chassis - internally connected to GND Cable shield connected to chassis 0 RXAUX Receive data of auxiliary RS (referred to GND) TXAUX Transmit data of auxiliary RS (referred to GND) 8 OUT + Configurable digital output positive pin OUT - Configurable digital output negative pin OUT + Configurable digital output positive pin OUT - Configurable digital output negative pin 6 OUT A Configurable digital output polarity insensitive 7 OUT B Configurable digital output polarity insensitive 8 EXT_TRIG/PS A External trigger (polarity insensitive) for PS 9 EXT_TRIG/PS B External trigger (polarity insensitive) for PS 6 IN/ENC A Input signal (polarity insensitive) for Encoder 0 IN/ENC B Input signal (polarity insensitive) for Encoder INA Input signal (polarity insensitive) 5 INA Input signal (polarity insensitive) IN_REF Common reference of IN and IN (polarity insensitive) 9, VS Supply voltage positive pin, 5 GND Supply voltage negative pin Pin RS RS85 Full-Duplex RS85 Half-Duplex TX TX85+ RTX85+ RX * RX85+ RTS TX85- RTX85-5 CTS * RX85-7 GND_ISO GND_ISO GND_ISO * Do not leave floating, see Reference Manual for connection details. 5 5-pin male D-sub Connector 0 ma C.L. (INT-0 with C-BOX 00 only) see INT-0 instructions 9-pin Lonworks Connector Pinout Pin Name Function CHASSIS Cable shield internally connected by capacitor to chassis 9 VS Supply voltage positive pin GND Supply voltage negative pin 6 VS_I/O Supply voltage of I/O circuit Ref_I/O Reference voltage of I/O circuit SYS_ENC_I/O System signal 5 SYS_I/O System signal 7 LON A Lonworks line (polarity insensitive) 8 LON B Lonworks line (polarity insensitive) Female Male 9-pin Local Lonworks Connectors Network Termination: When building a local Lonworks system the network must be properly terminated by positioning a BTK-6000 terminator on the DS600 master reader (BTK-6000 female side) and on the last slave reader (BTK-6000 male side). to Master to Slave 9-pin female 9-pin male BTK-6000 Network Terminator

DS600 MASTER/SLAVE MODEL Connectivity: Point-to-Point Layout DS600 CAB-600X C-BOX 00 Local Host *P.S. PG6000 * P.S. (Presence Sensor) connected to External Trigger/PS input. Pass Through Layout *P.S. *P.S. Gryphon DS600 ENT DS600A ENT DS600A CAB-600X C-BOX 00 C-BOX 00 C-BOX 00 MAIN AUX *P.

6 DS600 MASTER/SLAVE MODEL Connectivity: Point-to-Point Layout DS600 CAB-600X C-BOX 00 Local Host *P.S. PG6000 * P.S. (Presence Sensor) connected to External Trigger/PS input. Pass Through Layout *P.S. *P.S. Gryphon DS600 ENT DS600A ENT DS600A CAB-600X C-BOX 00 C-BOX 00 C-BOX 00 MAIN AUX *P.S. Local Host PWR-0 Main Serial Interface Auxiliary Serial Interface * P.S. (Presence Sensor) connected to External Trigger/PS input.

RS Master/Slave Layout DS600 Master CAB-600X C-BOX 00 DS600A Slave ENT *P.S. Local Host C-BOX 00 DS600A Slave ENT PWR-0 C-BOX 00 Main Serial Interface Auxiliary Serial Interface * P.

7 DS600 MASTER/SLAVE MODEL *P.S. *P.S. Multiplexer Layout *P.S. DS600 ENT DS600A ENT DS600A PWR-0 CAB-600X C-BOX 00 C-BOX 00 C-BOX 00 MX000 # #0 # Local Host RS85 HD Main Interface * P.S. (Presence Sensor) connected to External Trigger/PS input. RS Master/Slave Layout DS600 Master CAB-600X C-BOX 00 DS600A Slave ENT *P.S. Local Host C-BOX 00 DS600A Slave ENT PWR-0 C-BOX 00 Main Serial Interface Auxiliary Serial Interface * P.S. (Presence Sensor) connected to External Trigger/PS input. 5

DS600 MASTER/SLAVE MODEL Local Lonworks Network CAB-60X CAB-60XX BTK-6000 C-BOX 00** Master Encoder*** BTK-6000 Slave *P.S. Local Host CAB-6XX PWR-0 Small Synchronized Network with Readers * P.S. (Presence Sensor) connected to External Trigger/PS input.

8 DS600 MASTER/SLAVE MODEL Local Lonworks Network CAB-60X CAB-60XX BTK-6000 C-BOX 00** Master Encoder*** BTK-6000 Slave *P.S. Local Host CAB-6XX PWR-0 Small Synchronized Network with Readers * P.S. (Presence Sensor) connected to External Trigger/PS input. ** C-BOX 00 modified to accept scanner power. *** Encoder connected to IN/ENC input. Slave Slave Local Lonworks Network Master CAB-60X CAB-60X BTK-6000 C-BOX 00** CAB-600X *P.S. CAB-60X Encoder*** CAB-60X CAB-60X Host BTK-6000 CAB-6XX Slave 5 Slave Slave PWR-0 CAB-6XX Small Synchronized Network with more than Readers and Single Power Unit * P.S. (Presence Sensor) connected to External Trigger/PS input. ** C-BOX 00 modified to accept scanner power. *** Encoder connected to IN/ENC input. 6

9 DS600 MASTER/SLAVE MODEL Large Synchronized Network ** * * P.S. (Presence Sensor) connected to External Trigger/PS input. ** Encoder connected to ENC input. Large Synchronized Network with DX6X00 and DS6XXX Scanners 7

DS600 PROFIBUS MODEL DS600-00-0 PROFIBUS MODEL Figure A Laser Beam Output Window 5 Figure B Figure C Programming Keypad Power On LED (Red) Profibus 9-pin Female Connector (white) TX Data LED (Green)

10 DS600 PROFIBUS MODEL DS PROFIBUS MODEL Figure A Laser Beam Output Window 5 Figure B Figure C Programming Keypad Power On LED (Red) Profibus 9-pin Female Connector (white) TX Data LED (Green) 5 LCD Display Lonworks 9-pin Female Connector Phase On LED (Yellow) Main/Aux. Interface 6-pin D-Sub Male Connector Available Models: Optical Model 0 = Standard 5 = Oscillating Mirror DS600-0X - 0YY Decoder Model 0 = Master/Slave = Profibus = Ethernet 5 = Devicenet Technical Features: ELECTRICAL FEATURES OPTICAL FEATURES Supply Voltage 5-0 Vdc Light Receiver Avalanche photodiode Power Consumption 5 W typical 0 W Max. (including startup current) Wavelength 60 to 680 nm Communication Interfaces Main (isolated) RS RS85 full-duplex RS85 half-duplex 0 ma C.L. (INT-0 with C-BOX 00 only) Auxiliary Baud Rate 00 to 500 RS 00 to 500 Other Lonworks.5 Mb/s Profibus Mb/s Safety Class Class -EN 6085-; Class II-CDRH Laser Control READING FEATURES Security system to turn laser off in case of motor slow down 900 Scan Rate scans/s Max. Resolution Max. Read. Distance Max. Read. Width Max. Depth of Field (see reading diagram) Inputs Ext. Trigger, aux. digital (optocoupled NPN or PNP) USER INTERFACE inputs LCD Display lines by 6 characters LCD Outputs Keypad keys software LED Indicators Power ON (red) programmable (optocoupled) Phase ON (yellow) digital outputs TX Data (green) 8

11 DS600 PROFIBUS MODEL SOFTWARE FEATURES ENVIRONMENTAL FEATURES Readable Codes Interleaved /5 Operating 0 to +0 C Code 9 standard Temperature (+ to +0 F) Codabar -0 to +70 C Storage Temperature Code 8 (- to +58 F) EAN 8 Humidity 90% non condensing Code 9 (Standard & Full ASCII) Ambient Light EAN/UPC (including Add-on and Immunity 500 lux Add-on 5) Vibration Resistance to 0Hz Code Selection Up to 0 codes during one reading IEC test FC.5 to 55 Hz phase 70 to 00 Hz hours on each axis Headers and Up to 8-byte headers and8- Shock Resistance 0 g; ms Terminators byte terminators IEC test EA shocks on each axis Operating Protection Class IP6 On Line, Automatic, Test Modes Config. Mode Genius utility program Param. Storage Non-volatile internal FLASH PHYSICAL FEATURES Std Models Oscill. Mirror Dimensions mm (inch) 0xx99 (.x.5x.9) x80x0.5 (.5x7.08x.) Weight.5 kg (. lb).0 kg (. lb) Accessories: Name Description Part Number CAB-60 Cable to C-BOX00 m 9A05 CAB-60 Cable to C-BOX00 m 9A05 CAB-605 Cable to C-BOX00 5 m 9A05 C-BOX 00 Passive connection box 9ACC50 INT-0 0 ma C.L. interface board for C-BOX 00 9A50 GFC mirror 9A000 GFC mirror close distance 9A00 GFX-60 X-pattern mirror 9ACC70 PWR-0 Power unit 0/0 V AC - V DC 9ACC50 BTK-6000 Terminator kit (5 pcs) 9ACC70 PG600 Single unit power supply US 9ACC78 PG600 Single unit power supply UK 9ACC79 PG6000 Single unit power supply EU 9ACC70 FBK-6000 Fast bracket kit ( pcs) 9ACC7 US-60 Mounting bracket kit (5 pcs) for multisided stations 9ACC79 PH- Photocell kit - PNP 9ACC79 MEP-5 Photocell kit NPN 9ACC78 OEK- Optical encoder (0 m cable + spring) 9ACC770 OEK- Optical encoder kit + 0 m cable 9ACC600 Electrical Connections: The DS600 Profibus reader provides a 6-pin male D-sub connector for connection to power supply and input/output signals. An 9-pin Profibus connector is used for connection to the remote Host, while a local Lonworks 9-pin female connector connects the Profibus master to the first slave reader of the system. The details of the connector pins are indicated in the following table: 9

12 DS600 PROFIBUS MODEL 6-pin D-Sub Connector Pinout Pin Name Function CHASSIS Chassis - internally connected to GND Cable shield connected to chassis 0 RXAUX Receive data of auxiliary RS (referred to GND) TXAUX Transmit data of auxiliary RS (referred to GND) 8 OUT + Configurable digital output positive pin OUT - Configurable digital output negative pin OUT + Configurable digital output positive pin OUT - Configurable digital output negative pin 9 6 OUT A Configurable digital output polarity insensitive OUT B Configurable digital output polarity insensitive EXT_TRIG/PS A External trigger (polarity insensitive) for PS 9 EXT_TRIG/PS B External trigger (polarity insensitive)for PS 6-pin male D-sub Connector 6 IN/ENC A Input signal (polarity insensitive) for Encoder 0 IN/ENC B Input signal (polarity insensitive) for Encoder INA Input signal (polarity insensitive) 5 INA Input signal (polarity insensitive) IN_REF Common reference of IN and IN (polarity insensitive) 9, VS Supply voltage positive pin, 5, 6 GND Supply voltage negative pin Pin RS RS85 Full-Duplex RS85 Half-Duplex TX TX85+ RTX85+ RX * RX85+ RTS TX85- RTX85-5 CTS * RX85-7 GND_ISO GND_ISO GND_ISO * Do not leave floating, see Reference Manual for connection details. 0 ma C.L. (INT-0 with C-BOX 00 only) see INT-0 instructions 9-pin Lonworks Connector Pinout Pin Name Function CHASSIS Cable shield internally connected by capacitor to chassis 9 VS Supply voltage positive pin GND Supply voltage negative pin 6 VS_I/O Supply voltage of I/O circuit Ref_I/O Reference voltage of I/O circuit SYS_ENC_I/O System signal 5 SYS_I/O System signal 7 LON A Lonworks line (polarity insensitive) 8 LON B Lonworks line (polarity insensitive) pin female Local Lonworks Connector 9-pin Profibus Connector Pin Name Function Shield Shield, Protective Ground resp. (optional) Free B-LINE (RxD/TxD-P) Received/Transmitted Data-P CNTR-P Repeater Control Signal (optional, RS85 level) 5 DGND Data Ground (M5V) 6 +5 V Voltage Plus (P5V) 7 Free 8 A-LINE (RxD/TxD-N) Received/Transmitted Data 9 CNTR-N Repeater Control Signal pin female Profibus Connector (white) 0

13 DS600 PROFIBUS MODEL Connectivity: Point-to-Point Layout Remote Host Fieldbus Network DS600 C-BOX 00 CAB-60X *P.S PG6000 * P.S. (Presence Sensor) connected to External Trigger/PS input. Remote Host Pass Through Layout *P.S. *P.S. Gryphon DS600 Fieldbus Network ENT DS600A ENT DS600A CAB-60X C-BOX 00 C-BOX 00 AUX C-BOX 00 *P.S. PWR-0 Main Serial Interface Auxiliary Serial Interface * P.S. (Presence Sensor) connected to External Trigger/PS input.

14 DS600 PROFIBUS MODEL Local Lonworks Network Remote Host Fieldbus Network Slave *** Slave *** Master C-BOX 00** CAB-60X CAB-60X CAB-60X CAB-60XX P.S.* CAB-60X BTK-6000 CAB-60X CAB-6XX Encoder**** Slave 5*** Slave *** Slave *** PWR-0 CAB-6XX Fieldbus Small Synchronized Network * P.S. (Presence Sensor) connected to External Trigger/PS input. ** C-BOX 00 modified to accept scanner power. *** The Slave scanners are Master/Slave models, which allow Lonworks network propagation. **** Encoder connected to IN/ENC input.

DS600 ETHERNET MODEL DS600-00-0 ETHERNET MODEL Figure A Laser Beam Output Window 5 Figure B Figure C Programming Keypad Power On LED (Red) RJ5 Modular Connector for Ethernet Interface TX Data LED

15 DS600 ETHERNET MODEL DS ETHERNET MODEL Figure A Laser Beam Output Window 5 Figure B Figure C Programming Keypad Power On LED (Red) RJ5 Modular Connector for Ethernet Interface TX Data LED (Green) 5 LCD Display Lonworks 9-pin Female Connector Phase On LED (Yellow) Main/Aux. Interface 6-pin D-Sub Male Connector Available Models: Optical Model 0 = Standard 5 = Oscillating Mirror DS6500-0X - 0YY Decoder Model 0 = Master/Slave = Profibus = Ethernet 5 = Devicenet Technical Features: ELECTRICAL FEATURES OPTICAL FEATURES Supply Voltage 5-0 Vdc Light Receiver Avalanche photodiode Power 5 W typical Wavelength 60 to 680 nm Consumption 0 W Max. (including startup current) Safety Class Class -EN 6085-; Class II- Communication Main (isolated) Baud Rate CDRH Interfaces RS Laser Control Security system to turn laser RS85 full-duplex 00 to 500 off in case of motor slow down RS85 half-duplex READING FEATURES 0 ma C.L. (INT-0 with C-BOX 00 only) 900 Scan Rate scans/s Auxiliary RS 00 to 500 Max. Resolution Other Lonworks.5 Mb/s Max. Read. Distance Max. Read. Width (see reading diagram) Ethernet 0 or 00 Mb/s Max. Depth of Field Inputs Ext. Trigger, aux. digital (optocoupled NPN or PNP) USER INTERFACE inputs LCD Display lines by 6 characters LCD Outputs Keypad keys software programmable digital outputs (optocoupled) LED Indicators Power ON (red) Phase ON (yellow) TX Data (green)

16 DS600 ETHERNET MODEL SOFTWARE FEATURES ENVIRONMENTAL FEATURES Readable Codes Interleaved /5 Operating 0 to +0 C Code 9 standard Temperature (+ to +0 F) Codabar -0 to +70 C Storage Temperature Code 8 (- to +58 F) EAN 8 Humidity 90% non condensing Code 9 (Standard & Full ASCII) Ambient Light EAN/UPC (including Add-on and Immunity 500 lux Add-on 5) Vibration Resistance to 0Hz Code Selection Up to 0 codes during one reading IEC test FC.5 to 55 Hz phase 70 to 00 Hz hours on each axis Headers and Up to 8-byte headers and8- Shock Resistance 0 g; ms Terminators byte terminators IEC test EA shocks on each axis Operating Protection Class IP50 On Line, Automatic, Test Modes Config. Mode Genius utility program Param. Storage Non-volatile internal FLASH PHYSICAL FEATURES Std Models Oscill. Mirror Dimensions mm (inch) 0xx99 (.x.5x.9) x80x0.5 (.5x7.08x.) Weight.5 kg (. lb).0 kg (. lb) Accessories: Name Description Part Number CAB-60 Cable to C-BOX00 m 9A05 CAB-60 Cable to C-BOX00 m 9A05 CAB-605 Cable to C-BOX00 5 m 9A05 C-BOX 00 Passive connection box 9ACC50 INT-0 0 ma C.L. interface board for C-BOX 00 9A50 GFC mirror 9A000 GFC mirror close distance 9A00 GFX-60 X-pattern mirror 9ACC70 PWR-0 Power unit 0/0 V AC - V DC 9ACC50 BTK-6000 Terminator kit (5 pcs) 9ACC70 PG600 Single unit power supply US 9ACC78 PG600 Single unit power supply UK 9ACC79 PG6000 Single unit power supply EU 9ACC70 FBK-6000 Fast bracket kit ( pcs) 9ACC7 US-60 Mounting bracket kit (5 pcs) for multisided stations 9ACC79 PH- Photocell kit - PNP 9ACC79 MEP-5 Photocell kit NPN 9ACC78 OEK- Optical encoder (0 m cable + spring) 9ACC770 OEK- Optical encoder kit + 0 m cable 9ACC600 Electrical Connections: The DS600 Ethernet reader provides a 6-pin male D-sub connector for connection to power supply and input/output signals. An Ethernet connector is used for connection to the remote Host (for ex. Remote PC connected via Internet), while a local Lonworks 9-pin female connector connects the Ethernet master to the first slave reader of the system. The details of the connector pins are indicated in the following table:

DS600 ETHERNET MODEL 6-pin D-Sub Connector Pinout Pin Name Function CHASSIS Chassis - internally connected to GND Cable shield connected to chassis 0 RXAUX Receive data of auxiliary RS (referred to

17 DS600 ETHERNET MODEL 6-pin D-Sub Connector Pinout Pin Name Function CHASSIS Chassis - internally connected to GND Cable shield connected to chassis 0 RXAUX Receive data of auxiliary RS (referred to GND) TXAUX Transmit data of auxiliary RS (referred to GND) 8 OUT + Configurable digital output positive pin OUT - Configurable digital output negative pin OUT + Configurable digital output positive pin OUT - Configurable digital output negative pin 9 6 OUT A Configurable digital output polarity insensitive OUT B Configurable digital output polarity insensitive EXT_TRIG/PS A External trigger (polarity insensitive) for PS 9 EXT_TRIG/PS B External trigger (polarity insensitive) for PS 6-pin male D-sub Connector 6 IN/ENC A Input signal (polarity insensitive) for Encoder 0 IN/ENC B Input signal (polarity insensitive) for Encoder INA Input signal (polarity insensitive) 5 INA Input signal (polarity insensitive) IN_REF Common reference of IN and IN (polarity insensitive) 9, VS Supply voltage positive pin, 5, 6 GND Supply voltage negative pin Pin RS RS85 Full-Duplex RS85 Half-Duplex TX TX85+ RTX85+ RX * RX85+ RTS TX85- RTX85-5 CTS * RX85-7 GND_ISO GND_ISO GND_ISO * Do not leave floating, see Reference Manual for connection details. 0 ma C.L. (INT-0 with C-BOX 00 only) see INT-0 instructions 9-pin Lonworks Connector Pinout Pin Name Function CHASSIS Cable shield internally connected by capacitor to chassis 9 VS Supply voltage positive pin GND Supply voltage negative pin 6 VS_I/O Supply voltage of I/O circuit Ref_I/O Reference voltage of I/O circuit SYS_ENC_I/O System signal 5 SYS_I/O System signal 7 LON A Lonworks line (polarity insensitive) 8 LON B Lonworks line (polarity insensitive) pin female Local Lonworks Connector DS600 HUB / SWITCH RJ5 Modular Connector TX+ TX- RX+ 8 n. c. n. c. 5 5 RX- 6 6 n. c. n. c RJ5 Modular Connector n. c. = not connected 5

18 DS600 ETHERNET MODEL Connectivity: Point-to-Point Layout Remote Host Fieldbus Network DS600 C-BOX 00 CAB-60X *P.S PG6000 * P.S. (Presence Sensor) connected to External Trigger/PS input. Remote Host Pass Through Layout *P.S. *P.S. Gryphon DS600 Fieldbus Network ENT DS600A ENT DS600A CAB-60X C-BOX 00 C-BOX 00 AUX C-BOX 00 *P.S. PWR-0 Main Serial Interface Auxiliary Serial Interface * P.S. (Presence Sensor) connected to External Trigger/PS input. 6

19 DS600 ETHERNET MODEL Local Lonworks Network Remote Host Fieldbus Network Slave *** Slave *** Master C-BOX 00** CAB-60X CAB-60X CAB-60X CAB-60XX P.S.* CAB-60X BTK-6000 CAB-60X CAB-6XX Encoder**** Slave 5*** Slave *** Slave *** PWR-0 CAB-6XX Fieldbus Small Synchronized Network * P.S. (Presence Sensor) connected to External Trigger/PS input. ** C-BOX 00 modified to accept scanner power. *** The Slave scanners are Master/Slave models, which allow Lonworks network propagation. **** Encoder connected to IN/ENC input. 7

DS600 DEVICENET MODEL DS600-00-05 DEVICENET MODEL Figure A Laser Beam Output Window 5 Figure B Figure C Programming Keypad TX Data LED (Green) Phase On LED (Yellow) 5 Power On LED (Red) LCD Display

20 DS600 DEVICENET MODEL DS DEVICENET MODEL Figure A Laser Beam Output Window 5 Figure B Figure C Programming Keypad TX Data LED (Green) Phase On LED (Yellow) 5 Power On LED (Red) LCD Display Main/Aux. Interface 6-pin D-sub Male Connector Lonworks 9-pin Female Connector DeviceNet 5-pin Male Connector Available Models: Optical Model 0 = Standard 5 = Oscillating Mirror DS600-0X - 0YY Decoder Model 0 = Master/Slave = Profibus = Ethernet 5 = Devicenet Technical Features: ELECTRICAL FEATURES OPTICAL FEATURES Supply Voltage 5-0 Vdc Light Receiver Avalanche photodiode Power Consumption Wavelength 60 to 680 nm Communication Interfaces 5 W typical 0 W Max. (including startup current) Safety Class Class -EN 6085-; Class II-CDRH Main (isolated) Baud Rate Laser Control Security system to turn laser RS RS85 full-duplex 00 to 500 RS85 half-duplex 0 ma C.L. (INT with C-BOX 00 only) Auxiliary RS 00 to 500 Other Lonworks.5 Mb/s DeviceNet 5 or 50 Kb/s Inputs Ext. Trigger, aux. digital inputs (optocoupled NPN or PNP) Outputs software programmable digital outputs (optocoupled) off in case of motor slow down READING FEATURES Scan Rate scans/s Max. Resolution Max. Read. Distance Max. Read. Width Max. Depth of Field USER INTERFACE LCD Display Keypad LED Indicators (see reading diagram) lines by 6 characters LCD keys Power ON (red) Phase ON (yellow) TX Data (green) 8

21 DS600 DEVICENET MODEL SOFTWARE FEATURES ENVIRONMENTAL FEATURES Readable Codes Interleaved /5 Operating 0 to +0 C Code 9 standard Temperature (+ to +0 F) Codabar -0 to +70 C Storage Temperature Code 8 (- to +58 F) EAN 8 Humidity 90% non condensing Code 9 (Standard & Full ASCII) Ambient Light EAN/UPC (including Add-on and Immunity 500 lux Add-on 5) Vibration Resistance to 0Hz Code Selection Up to 0 codes during one reading IEC test FC.5 to 55 Hz phase 70 to 00 Hz hours on each axis Headers and Up to 8-byte headers and8- Shock Resistance 0 g; ms Terminators byte terminators IEC test EA shocks on each axis Operating Protection Class IP6 On Line, Automatic, Test Modes Config. Mode Genius utility program Param. Storage Non-volatile internal FLASH PHYSICAL FEATURES Std Models Oscill. Mirror Dimensions mm (inch) 0xx99 (.x.5x.9) x80x0.5 (.5x7.08x.) Weight.5 kg (. lb).0 kg (. lb) Accessories: Name Description Part Number CAB-60 Cable to C-BOX00 m 9A05 CAB-60 Cable to C-BOX00 m 9A05 CAB-605 Cable to C-BOX00 5 m 9A05 C-BOX 00 Passive connection box 9ACC50 INT-0 0 ma C.L. interface board for C-BOX 00 9A50 GFC mirror 9A000 GFC mirror close distance 9A00 GFX-60 X-pattern mirror 9ACC70 PWR-0 Power unit 0/0 V AC - V DC 9ACC50 BTK-6000 Terminator kit (5 pcs) 9ACC70 PG600 Single unit power supply US 9ACC78 PG600 Single unit power supply UK 9ACC79 PG6000 Single unit power supply EU 9ACC70 FBK-6000 Fast bracket kit ( pcs) 9ACC7 US-60 Mounting bracket kit (5 pcs) for multisided stations 9ACC79 PH- Photocell kit - PNP 9ACC79 MEP-5 Photocell kit NPN 9ACC78 OEK- Optical encoder (0 m cable + spring) 9ACC770 OEK- Optical encoder kit + 0 m cable 9ACC600 Electrical Connections: The DS600 DeviceNet reader provides a 6-pin male D-sub connector for connection to power supply and input/output signals. A DeviceNet connector is used for connection to the remote Host, while a local Lonworks 9-pin female connector connects the DeviceNet master to the first slave reader of the system. NOTE When using DeviceNet, the Main serial interface is disabled and must not be physically connected. 9

22 DS600 DEVICENET MODEL The details of the connector pins are indicated in the following table: 6-pin D-Sub Connector Pinout Pin Name Function CHASSIS Chassis - internally connected to GND Cable shield connected to chassis 0 RXAUX Receive data of auxiliary RS (referred to GND) TXAUX Transmit data of auxiliary RS (referred to GND) 8 OUT + Configurable digital output positive pin OUT - Configurable digital output negative pin OUT + Configurable digital output positive pin OUT - Configurable digital output negative pin 9 6 OUT A Configurable digital output polarity insensitive OUT B Configurable digital output polarity insensitive EXT_TRIG/PS A External trigger (polarity insensitive) for PS 9 EXT_TRIG/PS B External trigger (polarity insensitive) for PS 6-pin male D-sub Connector 6 IN/ENC A Input signal (polarity insensitive) for Encoder 0 IN/ENC B Input signal (polarity insensitive) for Encoder INA Input signal (polarity insensitive) 5 INA Input signal (polarity insensitive) IN_REF Common reference of IN and IN (polarity insensitive) 9, VS Supply voltage positive pin, 5, 6 GND Supply voltage negative pin Pin RS RS85 Full-Duplex RS85 Half-Duplex TX TX85+ RTX85+ RX * RX85+ RTS TX85- RTX85-5 CTS * RX85-7 GND_ISO GND_ISO GND_ISO * Do not leave floating, see Reference Manual for connection details. Pin Name Function 9-pin Lonworks Connector Pinout CHASSIS Cable shield internally connected by capacitor to chassis 9 VS Supply voltage positive pin GND Supply voltage negative pin 6 VS_I/O Supply voltage of I/O circuit Ref_I/O Reference voltage of I/O circuit SYS_ENC_I/O System signal 5 SYS_I/O System signal 7 LON A Lonworks line (polarity insensitive) 8 LON B Lonworks line (polarity insensitive) 5-pin DeviceNet Connector Pinout Pin Name Function V+ Supply voltage positive pin 5 CAN_L CAN bus data line L SHIELD Shield CAN_H CAN bus data line H V- Supply voltage negative pin ma C.L (INT-0 with C-BOX 00 only) see INT-0 instructions 9-pin female Local Lonworks Connector 5 5-pin male DeviceNet Connector NOTE The power supplied on pin V+ and V- is used only to propagate power to the section of the DeviceNet board directly connected to the Bus. It is completely isolated from the DS600 power which must be supplied on pin 9, and pin, 5 of the 6-pin Main/Aux connector. 0

S. *P.S. Gryphon DS600 Fieldbus Network ENT DS600A ENT DS600A CAB-60X C-BOX 00 C-BOX 00 AUX C-BOX 00 *P.S. PWR-0 Main Serial Interface Auxiliary Serial Interface * P.

23 DS600 DEVICENET MODEL Connectivity: Point-to-Point Layout Remote Host Fieldbus Network DS600 C-BOX 00 CAB-60X *P.S PG6000 * P.S. (Presence Sensor) connected to External Trigger/PS input. Remote Host Pass Through Layout *P.S. *P.S. Gryphon DS600 Fieldbus Network ENT DS600A ENT DS600A CAB-60X C-BOX 00 C-BOX 00 AUX C-BOX 00 *P.S. PWR-0 Main Serial Interface Auxiliary Serial Interface * P.S. (Presence Sensor) connected to External Trigger/PS input.

DS600 DEVICENET MODEL Local Lonworks Network Remote Host Fieldbus Network Slave *** Slave *** Master C-BOX 00** CAB-60X CAB-60X CAB-60X CAB-60XX P.S.* CAB-60X BTK-6000 CAB-60X CAB-6XX Encoder**** Slave 5*** Slave *** Slave *** PWR-0 CAB-6XX Fieldbus Small Synchronized Network * P.

24 DS600 DEVICENET MODEL Local Lonworks Network Remote Host Fieldbus Network Slave *** Slave *** Master C-BOX 00** CAB-60X CAB-60X CAB-60X CAB-60XX P.S.* CAB-60X BTK-6000 CAB-60X CAB-6XX Encoder**** Slave 5*** Slave *** Slave *** PWR-0 CAB-6XX Fieldbus Small Synchronized Network * P.S. (Presence Sensor) connected to External Trigger/PS input. ** C-BOX 00 modified to accept scanner power. *** The Slave scanners are Master/Slave models, which allow Lonworks network propagation. **** Encoder connected to IN/ENC input.

25 0 DS XX OSCILLATING MIRROR MODEL DS600 OSCILLATING MIRROR MODEL Figure A Laser Beam Output Window Oscillating mirror models are used when coverage of a large reading area is required, mainly in picket fence applications. The DS600 scanner mounts a dedicated optic head with integrated oscillating mirror driven by a linear motor. The speed, precision, repeatability, and reliability of this driving technology assure high level performance. The new oscillating mirror is completely software controlled and software programmable. The Genius software tool allows adjusting the linear motor speed (oscillating frequency) and the upper and lower limits of the oscillation by defining the top and bottom line limit angles. When the oscillating mirror is programmed to read barcode labels at very small angles, position the reader to assure at least 0 for the Skew angle (see DS600 Reference Manual). This angle refers to the most inclined or external laser line, so that all other laser lines assure more than 0 Skew. This avoids the direct reflection of the laser light emitted by the reader. Oscillating Mirror Skew Angle Otherwise, the scanner can be mounted at an angle of inclination of 7.5 in order to attain symmetrical deflection ranges Oscillating Mirror Reading Position In the above case, the zone where the scan line is perpendicular to the reflecting surface corresponds to a neutral zone at the center of the reading field.

26 DS600 OSCILLATING MIRROR MODEL The mirror can be deflected up to 0. Oscillation with respect to the output window median axis is asymmetrical (see figure below) Oscillating Mirror Maximum Aperture and Asymmetry By configuring the oscillating speed up to the maximum value of 9 Hz, raster emulation can be performed for reading fast moving objects. Hz Max. Aperture NOTE By limiting the raster width to the minimum necessary, the number of scans on the reading surface is increased. Oscillating angles are selected in software where the minimum and maximum angles correspond to.5 and The scanner can be tilted in order for the 7.5 software setting to correspond with the 0 horizontal plane Oscillating Mirror Extreme Angle Positions These models provide higher scanning speed (00 scans/sec) compared to standard models and the reading performance is not adversely effected by the oscillating mirror. The example represents the selection of an angle of +0 for the bottom line and an angle of +0 for the top line (see figure beside) Oscillating Mode

27 COMMON FEATURES COMMON FEATURES C-BOX 00 Pinout for DS600: The table below gives the pinout of the C-BOX 00 terminal block connectors. Use this pinout when the DS600 reader is connected in a network by means of the C-BOX 00: C-BOX 00 Terminal Block Connectors Power,, 5 VS,, 6 GND 7, 8 EARTH GROUND 0, 0 Reserved Inputs 7 EXT TRIG/PS A (polarity insensitive) for PS 8 EXT TRIG/PS B (polarity insensitive) for PS 9 IN /ENC A (polarity insensitive) for Encoder 0 IN /ENC B (polarity insensitive) for Encoder, IN A (polarity insensitive), IN A (polarity insensitive) 6 IN B/IN B Reference (polarity insensitive) Outputs OUT + OUT - OUT + OUT - 5 OUT A (polarity insensitive) 6 OUT B (polarity insensitive) Auxiliary Interface 5 TX AUX 7 RX AUX 8, 9 GND Main Interface RS RS85 Full-Duplex RS85 Half-Duplex, 5 TX TX 85+ RTX 85+, 6 RTS TX 85- RTX 85-7 RX * RX CTS * RX 85-0,, 9 SGND Main Isolated SGND Main Isolated SGND Main Isolated 9, RS85 Cable Shield RS85 Cable Shield 0 ma C.L. (with INT-0 only) see INT-0 instructions * Do not leave floating, see Reference Manual for connection details. 5

COMMON FEATURES Mechanical Installation: The DS600 reader can be positioned and installed in the best way possible as a result of the Step-A-Head TM feature.

28 COMMON FEATURES Mechanical Installation: The DS600 reader can be positioned and installed in the best way possible as a result of the Step-A-Head TM feature. Thanks to the separation between Head and Base, you can modify the orientation of the decoder base, and therefore display-keypad and connector panels, while keeping the optic head in the correct reading position. The reading head and the decoder base can be rotated independently from each other allowing the installation even in the most critical locations. To rotate the head follow the given procedure:. detach the head from the base by unscrewing the four fixing screws; Head Screws. rotate the head in the desired position;. loosen but don't remove the two screws on top of the head;. affix the head onto the base carefully aligning the four fixing screws and progressively tightening them about half-way; 5. completely tighten the two screws on top of the head; 6. completely tighten the four fixing screws. Step-A-Head Feature The following diagrams give the overall dimensions of the reader standard model, oscillating mirror model and mounting bracket. They may be used for their installation: Fixing Screw () N N SLOTS 0.8 N SLOTS Ø. N Ø0.6 N = = = = mm inch 8.5 N SLOTS 0. N SLOTS Ø8.5 Ø0. mm inch 0. DS600 Overall Dimensions ST-7 Mounting Bracket Overall Dimensions Ø R R R mm inch R Ø mm inch DS600 Oscillating Mirror Model Overall Dimensions ST-0 Mounting Bracket Overall Dimensions 6

29 COMMON FEATURES Typical Installations: Standard Installation The DS600 scanner is mounted on the ST-7 06 mounting bracket which guarantees a built-in Skew angle (S in the figure below) of 6 with respect to the frame plane (typically the Skew angle should be between 0-0 ). This avoids the direct reflection of the laser light emitted by the scanner. Furthermore, the bracket guides allow adjusting the Tilt angle (T in the figure below, which is typically 0 ) for the best scanner orientation: T S Conveyor Direction 5 Skew Installation The DS600 scanner is mounted on the ST-0 90 mounting bracket. By adjusting the mounting bracket guides, reach 5 for the Skew angle (S in the figure below) to avoid the direct reflection of the laser light emitted by the scanner: 5 S ATTENTION If using the 5 Skew installation, the scanner reading performance is not guaranteed to match that measured for the standard installation with Skew angle between 0-0 (see reading diagram section). The ST-0 mounting bracket is an accessory of the DS600 standard model available in the US-60 kit (order no ). NOTE WARNING When installing several scanners, take care to position them correctly so that no laser beam enters the reading window perpendicularly and at the same level of the output beam of the other scanners. This condition could occur more frequently for side mounted applications. If these precautions are not followed, it may occur that the laser of the blinded scanner starts blinking due to an internal circuit which temporarily turns the laser off when detecting a power anomaly. To resolve this problem, it is sufficient to slightly change the inclination and position of one of the two scanners involved. 7

30 COMMON FEATURES Adjustment: The DS600 provides a manual adjustment of the optics to optimize the reading performance by choosing the best focus between two extreme positions. The focus adjustment is continuous and not by step; thus, allowing an optimum adjustment around the selected position. The relative focus positions range from 0 to 00. The adjustment can be simply made through an external screw placed on the back of the optic HEAD and protected by a cap. The screw may be rotated either clockwise or counterclockwise in order to move the scanner internal lenses. In particular, a clockwise rotation causes a farther focus from the scanner, while a counterclockwise rotation causes a nearer focus to the scanner. An internal sensor tracks the exact laser beam focusing position allowing it to be shown on the reader display or through the Genius software program. WARNING Do not stare at the laser beam output window during this operation to avoid hazardous visible laser light. Refer to the following instructions when adjusting the focus: ) Remove the regulation screw protecting cap (see following Figure) positioned on the back of the optic Head; ) Press and hold both the (up arrow) and (down arrow) key for about seconds to enter the Main menu; ) Use the (up arrow) or (down arrow) key to select Test Mode item, then press the ENT (enter) key to confirm. The reader enters Test Mode; ) Press the ENT (enter) key to toggle between the graphical (default) and numerical visualization of the focus position; Display Visualization The first line of the display shows the read code and Good Read percentage. Possible suspending commas at the end of the code mean that the code is too long to be displayed. The second line of the display indicates the value of the focus position according to the table below. The indications Too Near or Too Far are represented for values outside the focus range. Graphical Visualization A ---^ where ^ indicates the focus position B N where N indicates that the focus position is Too Near C F where F indicates that the focus position is Too Far Numerical Visualization Fxxx where xxx ranges from 000 to 00 TooNear Fxxx* where xxx is greater than 00 CodeRead 00% ^ CodeRead 09% F0 Graphical Visualization Normal Visualization 5) Rotate the focus adjustment screw to reach the desired focus position. The display is refreshed with the new values; 6) Press the (up arrow) key to exit the Test Mode; To avoid breakage, do not use excessive force when rotating the focus adjustment screw. 8

It is possible to visualize the focus position and the reading percentage on the terminal tool provided by the Genius configuration program (see Genius Help On-Line for details).

31 COMMON FEATURES 7) Use the (up arrow) and (down arrow) key to select the Exit item, then press the ENT (enter) key to confirm. The scanner exits the Main Menu and returns to its current operating mode. Adjustment Screw NOTE The reader display shows the focus position only when the laser beam is activated. It is possible to visualize the focus position and the reading percentage on the terminal tool provided by the Genius configuration program (see Genius Help On-Line for details). Reading Conditions: ANSI Grade B minimum 800 scans/sec The following tables describe the requirements for standard applications. Minimum Code Height for ACR Reading (mm) 5 0 Conveyor Speed (m/s) /5 Interleaved Code Resolution (mm) Ratio : Table Minimum Code Height for ACR Reading (mm) 5 0 Conveyor Speed (m/s) Code 9 Code Resolution (mm) Ratio :; Interdigit = Module Size Table 9

32 COMMON FEATURES Minimum Code Height for ACR Reading (mm) 5 0 Conveyor Speed (m/s) Code 8 Ean 8 Code Resolution (mm) Table Minimum Code Height for ACR Reading (mm) 5 0 Conveyor Speed (m/s) Codabar Code Resolution (mm) Ratio :; Interdigit = Module Size Table Minimum Code Height for ACR Reading (mm) 5 0 Conveyor Speed (m/s) EAN 8-, UPC-A Code Resolution (mm) Table 5 0

33 COMMON FEATURES Reading Diagrams: In the following reading diagrams (0,0) is the center of the laser beam output window. DS XX Resolution: 0.0 mm/8 mils (in) (cm) Position = 0 Position = CONDITIONS Code = Interleaved /5 or Code 9 PCS = 0.90 Pitch angle = 0 Skew angle = 0-0 Tilt angle = (in) (cm) DS XX Resolution: 0.0 mm/ mils (in) (cm) Position = 0 CONDITIONS Code = Interleaved /5 or Code 9 PCS = 0.90 Pitch angle = 0 Skew angle = Position = 0 Tilt angle = (in) -5-0 (cm) Position = 60

34 COMMON FEATURES Reading Diagrams: DS XX Resolution: 0.8 mm/5 mils (in) (cm) Position = CONDITIONS Code = Interleaved /5 or Code 9 PCS = 0.90 Pitch angle = 0 Skew angle = 0-0 Tilt angle = Position = Position = (in)(cm) DS XX Resolution: 0.50 mm/0 mils (in) (cm) Position = 00 CONDITIONS Code = Interleaved /5 or Code 9 PCS = 0.90 Pitch angle = 0 Skew angle = 0-0 Tilt angle = (in) (cm) Position = 60 Position = 0

35 COMMON FEATURES Reading Diagrams: DS XX (Oscillating Mirror) Resolution: 0.0 mm/8 mils (in) (cm) Position = 0 Position = CONDITIONS Code = Interleaved /5 or Code 9 PCS = 0.90 Pitch angle = 0 Skew angle = 0-0 Tilt angle = (in) (cm) DS XX (Oscillating Mirror) Resolution: 0.0 mm/ mils (in) (cm) 0 5 CONDITIONS Code = Interleaved /5 or Code Position = 0 Position = 0 PCS = 0.90 Pitch angle = 0 Skew angle = Tilt angle = (in) -5-0 (cm) Position = 60

36 COMMON FEATURES Reading Diagrams: DS XX (Oscillating Mirror) Resolution: 0.8 mm/5 mils (in) (cm) Position = CONDITIONS Code = Interleaved /5 or Code 9 PCS = 0.90 Pitch angle = 0 Skew angle = 0-0 Tilt angle = Position = Position = (in)(cm) DS XX (Oscillating Mirror) Resolution: 0.50 mm/0 mils (in) (cm) 60 Position = 00 CONDITIONS Code = Interleaved /5 or Code 9 PCS = 0.90 Pitch angle = 0 Skew angle = 0-0 Tilt angle = Position = Position = 0 - (in) -60 (cm)

COMMON FEATURES User Interface: 5 RS PC-side connections 6 9 5 9-pin male connector 5-pin male connector Pin Name Pin Name RX RX TX TX 5 GND 7 GND 7 RTS RTS 8 CTS 5 CTS How To Build A Simple

37 COMMON FEATURES User Interface: 5 RS PC-side connections pin male connector 5-pin male connector Pin Name Pin Name RX RX TX TX 5 GND 7 GND 7 RTS RTS 8 CTS 5 CTS How To Build A Simple Interface Test Cable: The following wiring diagram shows a simple test cable including power, external (push-button) trigger and PC RS COM port connections. 5-pin D-sub female 9-pin D-sub female 0 TXAUX RXAUX RX TX PC GND 5 GND VS DS600 5 GND 9 VS 8 EXT TRIG A 9 EXT TRIG B Power Supply VS (5 0 VDC) Power GND Trigger Compliance: Laser Safety Figure A Laser Safety Label Figure B Warning and Device Class Label Identification Label 5

38 COMMON FEATURES Figure C Laser Safety Label The scanner is classified as a Class laser product according to EN regulations and as a Class II laser product according to CDRH regulations. Disconnect the power supply when opening the device during maintenance or installation to avoid exposure to hazardous laser light. There is a safety device which allows the laser to be switched on only if the motor is rotating above the threshold for its correct scanning speed. The laser beam can be switched off through a software command (see also the Genius Help On-Line). AVOID EXPOSURE LASER RADIATION IS EMITTED FROM THIS APERTURE AVOID EXPOSURE LASER LIGHT IS EMITTED FROM THIS APERTURE Laser Safety Label for Oscillating Mirror and Standard Models CAUTION-CLASS B LASER LIGHT WHEN OPEN AVOID EXPOSURE TO BEAM LASER LIGHT DO NOT STARE INTO BEAM CLASS LASER PRODUCT MAX. OUTPUT RADIATION mw EMITTED WAVE LENGTH 60 ~ 680 nm EN6085-:00 Warning and Device Class Label DATALOGIC S.p.A. Via Candini, 00 LIPPO DI CALDERARA DI RENO (BO) ITALY MANUFACTURED VOLT Amp. JANUARY DC MODEL No. SERIAL No. N68 This product conforms to the applicable requirements of CFR 00 at the date of manufacture. Device Identification Label The laser diode used in this device is classified as a Class B laser product according to EN regulations and as a Class IIIb laser product according to CDRH regulations. Any violation of the optic parts in particular can cause radiation up to the maximum level of the laser diode (5 mw at 60 ~ 680 nm). Power Supply - This product is intended to be installed by Qualified Personnel only. - All DS600 Models: This device is intended to be supplied by a UL Listed Power Unit marked Class or LPS power source which supplies power directly to the scanner via the 5/6-pin connector. CE Compliance Warning: This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. 6

39 DECLARATION OF CONFORMITY 07 Datalogic Automation S.r.l. Via S. Vitalino 00 - Lippo di Calderara Bologna - Italy dichiara che declares that the déclare que le bescheinigt, daß das Gerät declare que el DS600-XXX-XXX, Laser Scanner; e tutti i suoi modelli and all its models et tous ses modèles und seine Modelle y todos sus modelos sono conformi alle Direttive del Consiglio Europeo sottoelencate: are in conformity with the requirements of the European Council Directives listed below: sont conformes aux spécifications des Directives de l'union Européenne ci-dessous: der nachstehend angeführten Direktiven des Europäischen Rats: cumple con los requisitos de las Directivas del Consejo Europeo, según la lista siguiente: 89/6/EEC EMC Directive e 9//EEC, 9/68/EEC emendamenti successivi and further amendments et ses successifs amendements und späteren Abänderungen y succesivas enmiendas 006/95/EC Low Voltage Directive Basate sulle legislazioni degli Stati membri in relazione alla compatibilità elettromagnetica ed alla sicurezza dei prodotti. On the approximation of the laws of Member States relating to electromagnetic compatibility and product safety. Basée sur la législation des Etats membres relative à la compatibilité électromagnétique et à la sécurité des produits. Über die Annäherung der Gesetze der Mitgliedsstaaten in bezug auf elektromagnetische Verträglichkeit und Produktsicherheit entsprechen. Basado en la aproximación de las leyes de los Países Miembros respecto a la compatibilidad electromagnética y las Medidas de seguridad relativas al producto. Questa dichiarazione è basata sulla conformità dei prodotti alle norme seguenti: This declaration is based upon compliance of the products to the following standards: Cette déclaration repose sur la conformité des produits aux normes suivantes: Diese Erklärung basiert darauf, daß das Produkt den folgenden Normen entspricht: Esta declaración se basa en el cumplimiento de los productos con las siguientes normas: EN 550 (Class A ITE), August 99: Amendment A (Class A ITE), October 000: EN , October 00: LIMITS AND METHODS OF MEASUREMENTS OF RADIO DISTURBANCE CHARACTERISTICS OF INFORMATION TECHNOLOGY EQUIPMENT ELECTROMAGNETIC COMPATIBILITY (EMC) PART 6-: GENERIC STANDARDS - IMMUNITY FOR INDUSTRIAL ENVIRONMENTS EN , December 00: INFORMATION TECHNOLOGY EQUIPMENT SAFETY PART : GENERAL REQUIREMENTS EN 6085-, June 99: SAFETY OF LASER PRODUCTS Amendments A (996), A (00): PART : EQUIPMENT CLASSIFICATION, REQUIREMENTS AND USER'S GUIDE Lippo di Calderara, April nd, 007 Lorenzo Girotti Product & Process Quality Manager (Rev. I)

DS1100. LASER LIGHT DO NOT STARE INTO BEAM CLASS 2 LASER PRODUCT MAX. OUTPUT RADIATION 1mW EMITTED WAVE LENGTH nm TO EN :2001

DS1100. LASER LIGHT DO NOT STARE INTO BEAM CLASS 2 LASER PRODUCT MAX. OUTPUT RADIATION 1mW EMITTED WAVE LENGTH nm TO EN :2001 DS00 QUICK GUIDE General View: DS00 Laser Safety: The scanner is classified as a Class laser product according to EN 608- regulations and as a Class II laser product according to CDRH regulations. For