Installation Guide. Models covered

Transcription

1 Installation V uide Models covered S485 including optional elemetry Protocol Converter Software Version conv1_v7 V X457/557, Chugai/anz ZC-S122/123, ennard 2050, JVC 676, Mark Mercer, Panasonic CS850/860, VCL uilding lock Video Ltd., 17 pex Park, iplocks Industrial state, Hailsham, ast Sussex, 27 3JU UK. el: +44(0) Fax: +44(0) Support: +44(0)

2 1. P-ISLLI CHCKS SFY PCUS UPCKI Check Packaging - Upon taking delivery of the unit, inspect the packaging for signs of damage. If damage has occurred, advise the carriers and/or the suppliers immediately. Check Contents - Upon taking delivery of the unit, unpack the receiver carefully and check that all the items are present and correct. If any items are missing or damaged, contact your equipment dealer. etain Packaging - he shipping carton is the safest container in which to transport the unit. etain undamaged packaging for possible future use. IMP SFY PCUIS ead Instructions - ll relevant safety, installation and operating instructions should be read before attempting to install, connect or operate the unit. etain Instructions - ll safety, installation and operating instructions should be retained for future reference. Heed Warnings - ll warnings on the unit and in any relevant safety, installation or operating instructions should be adhered to. Cleaning - Unplug the unit from the power outlet before cleaning. o not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. ttachments - o not use attachments not recommended by the product manufacturer as they may cause hazards. Water and Moisture - o not expose the internal electronics of this unit to water or dampness; for example, in an unprotected outdoor installation, or in any area classified as a wet location. he unit as supplied conforms to ingress protection rating IP 67. his rating will be affected by any holes made in the enclosure. Cable entry points should be protected by the use of suitably rated glands and/or flexible conduit. It is not necessary to make further holes in the enclosure for mounting purposes, as mounting holes are provided at the corners of the enclosure outboard of the seal between enclosure and lid. ccessories - o not attach this unit to an unstable stand, bracket or mount. he unit may fall, causing serious injury to a person and serious damage to the unit. Power Sources - his unit should be operated only from the type of power source indicated on the manufacturer s label. If you are not sure of the type of power supply you intend to use, consult your equipment dealer or local power company. For units intended to operate from battery power or other sources, refer to operating instructions. S485 Star Card Manual V7 4 Mar 2003.doc Page 2/17

3 verloading - o not overload outlets and extension cords, as this can result in fire or electric shock. bject and Liquid ntry - ever push objects of any kind into the unit, as they may touch dangerous voltage points or short out parts that could result in fire or electric shock. ever spill liquid of any kind on or inside the unit. Servicing - Servicing of the unit should only be undertaken by qualified service personnel, as opening or removing covers may expose you to dangerous voltages or other hazards. amage equiring Service - Servicing by qualified personnel should be carried out under the following conditions: (a) When the power-supply cord or plug is damaged; (b) If liquid has been spilled, or objects have fallen into, the unit; (c) If the internal electronics of the unit have been exposed to rain or water; (d) If the unit does not operate normally by following the operating instructions. djust only those controls that are covered by the operating instructions, as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the unit to normal operation; (e) If the unit has been dropped or the enclosure is damaged; (f) If the unit exhibits a distinct change in performance. his indicates a need for service. eplacement Parts - If replacement parts are required, ensure that only replacement parts recommended by the product manufacturer are used. Safety Check - Upon completion of any service or repairs to the unit, safety checks should be performed to ensure that the unit is in proper operating condition. Coax rounding - If an outside cable system is connected to the unit, be sure the cable system is grounded. Pre-installation Checks - It is recommended that the unit be bench-tested prior to installation on the site. dhere to Safety Standards - ll normal safety precautions as laid down by ritish Standards and the Health and Safety at Work ct should be observed. WI PV F FI SHCK, XPS H IL CMPS F HIS QUIPM I MISU. he lightning flash with arrowhead symbol inside an equilateral triangle is used to warn the user of this equipment that there are sufficiently high voltages within the enclosure to constitute a risk of electric shock. he exclamation point symbol inside an equilateral triangle is used to alert the user of this equipment to important operating and maintenance (servicing) instructions in the literature accompanying the appliance. S485 Star Card Manual V7 4 Mar 2003.doc Page 3/17

4 echnical Specification Power equirements Inputs utputs Facilities ther utputs oxed imensions ptions 9Vdc 500m 2 or 4 wire S485 (switch selectable) 8 * 2 or 4 wire S485 (switch selectable FUL 4 WI) Maximum cable run approx Feet/1200M L as power and data indication S232 monitor output via chassis mounted 9 connector. vailable to mount in V X1500 sub rack or fitted in 19 1 U rack 100mm deep rack mountable case. Internally fitted elemetry Protocol Conversion board Version History V7 27 Feb dded support to control V X450 C & X550 C receivers 2. dded support to control Chugai/anz ZC-S122/123 dome V6 12 Feb Improved control of Panasonic WV-CS850/860 dome Patrol will now start LL domes patrolling 3. dded support for W mode selection V5 11 Feb dded support for V S485 output 2. dded support for JVC K-C676 protocol V4 5 Feb dded support for Panasonic WV-CS850/860 S485 dome protocol from V telemetry. 2. M connection details were incorrect, diagram now corrected. V3 4 ec 2002 ddition of protocol conversion module. S485 Star Card Manual V7 4 Mar 2003.doc Page 4/17

5 2. IUCI L he S485 Star Card is designed to simplify the installation of S485 telemetry systems. ight individual outputs are provided. ach output can be connected to a single dome/receiver or up to 32 domes/receivers wired as a daisy chain. When the domes/receivers are wired as a daisy chain, the last unit s S485 must be terminated and the intermediate units must be un-terminated. With a single dome connected to each output, the S485 must be terminated. he Star Card can be used with either 2 wire, half duplex; or 4 wire, full duplex systems. It has been tested with the Panasonic FS616 multiplexer in 2 and 4 wire modes and with the SX350 video matrix in 2 wire mode. he Star Card can also be used with single direction S485 links, for example the S485 output of M Systems Sprite and igital Sprite range of multiplexers and Integral echnologies VX range. he Star Card is protocol independent and will work at up to baud. It is recommended that when used with extended cable distances and/or noisy environments 9600 baud is used to prevent control problems. S232 serial output is provided via a 9F to aid with diagnostic and trouble shooting. he following pages showing wiring details when used in 2 and 4 wire systems. S485 Star Card Manual V7 4 Mar 2003.doc Page 5/17

6 Internal view of starcard showing switch settings SW1 SW2 J16 J22 SW3 J14 J15 Starcard PC Switches SW1 - S485 line termination for outputs 1-4 = termination (efault) SW1/1 & 1/2 = utput 1 termination SW1 setting showing termination SW1/3 & 1/4 = utput 2 termination SW1/5 & 1/6 = utput 3 termination SW1/7 & 1/8 = utput 4 termination SW2 - S485 line termination for outptus 5-8 = termination (efault) SW2/1 & 2/2 = utput 5 termination SW2 setting showing termination SW2/3 & 2/4 = utput 6 termination SW2/5 & 2/6 = utput 7 termination SW2/7 & 2/8 = utput 8 termination SW3 - ption selection. SW3/1 and SW3/2 - S485 input line termination = termination (efault) SW3/3-7 MUS FF SW3/8-2 or 4 wire selection. = 2 WI, FF = 4 WI SW3 setting showing 2 wire mode selected and S485 input termination SW3 setting showing 4 wire mode selected and S485 input termination S485 Star Card Manual V7 4 Mar 2003.doc Page 6/17

7 2 wire half-duplex mode 8 * S485 U Supply 9Vdc 500m Star 1 Star 2 Star 3 Star 4 Star 5 Star 6 Star 7 Star 8 Master V Starcard S232 monitor SW3 must be configured for 2 Wire as below: SWICH 8 V S485 or S485 I Close up view showing S485 connection into and out of the Star Card. Star n MS Frame ground o dome (-)/ o dome (+)/ Frame ground From controller (-) From controller (+) to PC pin 5 X to PC pin 2 he S232 output can be taken into a PC/laptop to allow the Starcard output to be displayed using Hyperterminal, elix or other comms program. S485 network length maximum 1200M per output. Please remember to terminate the last dome of each output. he baud and parity settings should match the values chosen with SW2. 2 wire S485 notes. 1. nsure that the dome/receiver is set for 2 wire telemetry, half-duplex. 2. he controller must be set for 2 wire using either a rear panel switch or menu access. Half duplex must be selected from within the setup menu. 3. aud rates for the controller and dome/receivers must be the same. It is advisable to use 9600 baud to reduce the possibility of corrupted data causing intermittent control. Panasonic Specific notes: FS616 - single S485 output is available. Connect the S485 output to the star card as shown. SX350 - wo S485 outputs are available. SX550/850 - ot required as each matrix S485 output card has eight individual outputs. S485 Star Card Manual V7 4 Mar 2003.doc Page 7/17

8 4 wire full-duplex mode 8 * S422 U Supply 9Vdc 500m Star 1 Star 2 Star 3 Star 4 Star 5 Star 6 Star 7 Star 8 Master V Starcard SW3 must be configured for 4 Wire as below: SWICH 8 FF S232 monitor V S422 or S422 I Close up view showing S422 connection into and out of the Star Card. Star n MS From dome (-) o dome (+) From dome (+) Frame ground o dome (-) From controller (-) o controller (+) From controller (+) Frame ground o controller (-) to PC pin 5 X to PC pin 2 he S232 output can be taken into a PC/laptop to allow the Starcard output to be displayed using Hyperterminal, elix or other comms program. S422 network length maximum 1200M per output. Please remember to terminate the last dome of each output. he baud and parity settings should match the values chosen with SW2. 4 wire S422 notes. 1. nsure that the dome/receiver is set for 4 wire telemetry, full-duplex. 2. he controller must be set for 4 wire using either a rear panel switch or menu access. Full duplex must be selected from within the setup menu. 3. aud rates for the controller and dome/receivers must be the same. It is advisable to use 9600 baud to reduce the possibility of corrupted data causing intermittent control. Panasonic Specific otes: FS616 - single S485 output is available. Connect the S485 output to the star card as shown. SX350 - ot compatible with 4 wire telemetry. SX550/850 - ot required as each matrix S485 output card has eight individual outputs. S485 Star Card Manual V7 4 Mar 2003.doc Page 8/17

9 Internal view showing optional protocol converter. When using the protocol converter, ensure that the starcard is set for 4 wire telemetry using SW3/8 FF. S485 data I to (+)/(-) and data U to domes (+)/(-) SW1 SW2 J14 J16 J22 SW1 SW J15 SW3 SW3/8 FF Close up view of protocol conversion card. SW SW2 L1 L2 L3 ata U / ata I / L1 = S485 out L2 = S485 in L3 = Checksum SW2 utput Settings Protocol conversion card (02003) fitted over headers J14, J15, J22. SW1 Input Settings Factory default switch settings shown old Italic. 1-3 Protocol Selection Protocol FF FF FF V S485 FF FF PLC P FF FF PLC 4-5 aud 4 5 aud FF FF 2400 FF 4800 FF Parity 6 7 Parity FF FF FF V FF 8 ata bits FF 8 IS 7 IS 1-4 Protocol Selection (Shown for V7 software!) Protocol FF FF FF FF SIH H FF FF FF U FF FF FF 2050 FF FF MK MC FF FF FF VCL P FF FF PSIC CS850/860 FF FF V-S485 FF JVC K-C676 FF FF FF V X450/X550 FF FF CHUI/Z ZC-S122/ aud 5 6 aud ote FF FF 2400 Panasonic CS850/860 and FF 4800 Chugai/anz ZC-S122 protocol FF 9600 can only be used with V telemetry! 7-8 Parity 7 8 Parity FF FF FF V FF ote: ot all output protocols are available with all input protocols. S485 Star Card Manual V7 4 Mar 2003.doc Page 9/17

10 S232 serial port. he 9F connector provides the ability to use a Laptop PC to monitor the data being sent out of the via S232. With the optional protocol converter fitted, on power up or if SW1 or SW2 switches are altered the unit sends the current protocol, baud rate and parity settings. Please be aware that the laptop baud rate and parity must match the settings selected with SW2. If the settings do not match then the laptop display will have no meaning. n power up message example is shown below : V Protocol Converter V5 SW1(I) = 10 V:9600,,8,1 SW2(U) = 3 MK MC V7.3:9600,,8,1 debug mode can also be selected using SW2/1, 2/2, 2/3 & 2/4 FF. his provides detailed information for each command received. Whilst trouble shooting V engineers may ask you to use this mode with a laptop. V Protocol Converter V5 SW1(I) = 10 V:9600,,8,1 SW2(U) = 21 U M:9600,,8,1 CM=00 W3=00 W4=14 W5=40 W6=24 PL CM=00 W3=00 W4=14 W5=06 W6=3C PL CM=00 W3=00 W4=12 W5=2 W6=38 P CM=00 W3=00 W4=12 W5=40 W6=08 P CM=00 W3=00 W4=08 W5=00 W6=0C U 012 CM=00 W3=00 W4=04 W5=40 W6=00 PL 064 CM=00 W3=00 W4=14 W5=32 W6=34 PL CM=00 W3=00 W4=12 W5=2 W6=38 P CM=00 W3=00 W4=04 W5=36 W6=00 PL 054 CM=00 W3=00 W4=00 W5=00 W6=00 Cam 00 stop he example above shows the debug output for camera 1. riving pan/tilt followed by a stop command. S485 Star Card Manual V7 4 Mar 2003.doc Page 10/17

11 Protocol specific information 2050 Function V Procedure Pelco Procedure isplay ome Menu #1 SV PS 95 isplay User Menu #2 PS 33 isplay echnicians Menu #3 PS 94 Start current dome s Sequence 001 PL 1 PS 97 Start LL MS Sequence 001 PL 2 PS 98 avigate through the dome menu using pan/tilt and issue PS 1 to select current line. MK MC Function V Procedure Pelco Procedure 180 Pan U turn #1 or WSH SV PS 95 Start current dome s patrol PL 1 PS 97 Start LL MS patrol PL 2 PS 98 VCL P Function V Procedure Pelco Procedure 180 Pan U turn #1 SV PS 95 nable Privacy Zone #2 PS 33 P PS 1-16 SV PS 1-16 isable Privacy Zone #3 PS 94 P PS 1-16 SV PS 1-16 Privacy areas can be enabled/disabled using a multiple commands. 16 privacy zones can be programmed and enabled. rive the camera to show the required privacy zone then Press #2 or PS 33 command followed by PM PS o disable a zone you must press #3 or PS 33 followed by PM PS 1-16 again. S485 Star Card Manual V7 4 Mar 2003.doc Page 11/17

12 PSIC WV-CS850/860 (dded in V 4 software) Control from V protocol only. Function V X1500 Procedure Show/Hide dome Menu 1# (whilst in menu) 2# SCP (whilst in menu) 3# SPCIL2 (whilst in menu) 4# Send PL U Send PL U to LL MS Send UP W M W M FF W M U 1 PL 2 PL UP 89 PS 88 PS 87 PS Switch and dome settings: VY IMP! nsure that each dome is configured F installation. utput baud rate must be set to 19200,,8,1 with SW2. he dome must be set to Panasonic CVIL protocol and the address set accordingly. he 4 way dome switch must be set to 4 wire telemetry with switches 2,3,4 FF. he S485 cable requires termination at the end of the run by setting switch 1. he Panasonic CS850/860 protocol conversion is only available when controlled using V S485 telemetry. If another input protocol is selected using SW1 then the unit will not function and all the Ls will flash until V protocol is selected again. ue to protocol issues, the response of an individual dome may become sluggish if several domes are controlled simultaneously. Connect to (green) and to (yellow). S485 Star Card Manual V7 4 Mar 2003.doc Page 12/17

13 JVC K-C676 (dded in version 5 software) Function V X1500 Pelco Procedure isplay menu and XI 1# SV PS 95 S (whilst in menu) 2# PS 33 oggle xtended ynamic ange 3# PS 94 Cycle W mode, /FF/U 4# Start dome U PL 1 PL PS 97 s above for LL MS 2 PL PS 98 Start dome UP UP PS 99 otes: Connect dome X- to Starcard and dome X+ to Starcard. ach dome must be set to Multi-drop, Simplex mode by setting dome switch 4 & 5. Set each dome address using the dome rotary switches. his address must match the number of the camera input of the telemetry controller. In JVC676 mode, the output baud rate and parity is fixed at 9600,,8,1. total of up to 96 domes are supported with a maximum of 32 domes per star output. o display the current dome s menu, press either 1# with the V x1500 or SV PS 95 using Pelco-P or Pelco- protocol. Use standard P/IL and where required ZM to navigate through the menus. o simulate the S key to navigate into sub-menus press 2# with a X1500 or PS 33 when using Pelco protocols. o exit the current menu press 1# for the X1500 or SV PS 95 with Pelco. ddition functions. Pressing UP with a X1500 or PS 99 with Pelco will cause the current dome to start an UP. Pressing 1 PL with a X1500 or PS 97 with Pelco will cause the current dome to start an UPL. Pressing 2 PL with a X1500 or PS 98 with Pelco will cause LL the domes to start an UPL. xtended ynamic ange can be toggled /FF using 3# with the X1500 or PS 94 with Pelco. /W Mode can be cycled between /FF/U using 4# with the X1500. Camera mode display. Protocol Converter SW2/8 If protocol converter switch SW2/8 is set to then each time the xtended ynamic ange or W mode is changed or UPL is selected then the dome title is altered to display these settings. If it is preferred to use the dome camera title for titling then set switch SW2/8 FF. he settings will still be changed but will not be shown. Presets he dome home preset position is preset 0. s most control systems do not directly support preset 0, preset 1 is used instead. his means that in practice, preset 1 is home, preset 2-32 are preset 2-32 and the dome s preset 1 is not used. his could only be an issue when programming alarms directly into the dome. o not use preset position 1 unless this is programmed from within the dome menu. S485 Star Card Manual V7 4 Mar 2003.doc Page 13/17

14 Chugai/anz ZC-S122/123 (dded in V7 software) Control from V protocol only. Function V X1500 Menu /FF 1# S (whilst in menu) 2# CL (whilst in menu) 3# PS SQUC PLYCK C UP UX 1 UPU /FF UX 2 UPU /FF 1 PL 2 PL UP LIHS WIP otes: Connect dome /+(pin 1, W) to Starcard and dome /- to Starcard. ach dome must be set to 9600 aud with switch 5 FF, switch 6. Set the dome address using the dome rotary switches to match the number of the camera input of the X1500. nsure that domes at the end of the S485 run are terminated by turning switch 8 and the intermediate domes have the switch 8 FF. In Chugai/anz ZC-S122/123 mode, the output baud rate and parity is fixed at 9600,,8,1. total of up to 96 domes are supported with a maximum of 32 domes per star output. Menu access. Press 1# will toggle the Menu display /FF. Whilst the menu is displayed the joystick is used to navigate. 2# is used as S to access a menu option and 3# is used as CL to go back. ddition functions are available for the currently displayed dome. UP is started by pressing the UP key. PS SQUC is started by pressing 1 PL. C playback is started by preseding 2 PL he protocol converter can directly access preset 1 64 by pressing the preset number followed by the PS key. o program a preset position, press PM followed by the preset number and the PS key. See the X1500 manual for detailed information. S485 Star Card Manual V7 4 Mar 2003.doc Page 14/17

15 S485 to domes/receivers S485 to domes/receivers S485 to domes/receivers ach leg 1200M Maximum ach leg 1200M Maximum Star Card Star Card Star Card ach leg 1200M Maximum Star Cards can be cascaded to suit each installation 1200M Maximum Star Card Control System S485 to domes/receivers S485 to domes/receivers S485 to domes/receivers ach leg 1200M Maximum ach leg 1200M Maximum Star Card Star Card Star Card Starcard SW3 setting X485 Unterminated 4 WI Starcard SW3 setting X485 Unterminated 4 WI Control System Starcard SW3 setting X485 terminated 4 WI n single direction S485, multiple s can be daisy chained to provide multiple outputs. S485 Star Card Manual V7 4 Mar 2003.doc Page 15/17

16 S485 Star Card Manual V7 4 Mar 2003.doc Page 16/17 Camera 1 C Head Camera 2 C Head Camera 3 C Head x550 ddress 1 x450 ddress 2 x550 ddress 3 erminated erminated erminated erminated SX350 V S485 Key S485 Coax 2 Wire connection details M Y L L W W x450 x550 SC SC SX350 SC 2 1 Panasonic SX-350 Wiring etails he SX350 has two individual S485 ports. ach port may be connected to a seperate. he diagram on the left shows a connection to port 2. Camera 1 C Head Camera 2 C Head Camera 3 C Head x550 ddress 1 x450 ddress 2 x550 ddress 3 erminated erminated erminated erminated FS616 V S485 Key S485 Coax 4 Wire connection details M Y L L W W x450 x550 SC SC SC FS616 2 Wire connection details M Y L L W W x450 x550 SC SC SC FS616 Panasonic FS-616 Wiring etails

17 Camera 1 C Head Camera 2 C Head Camera 3 C Head x552 ddress 1 erminated x452 ddress 2 erminated x552 ddress 3 erminated erminated Key S485 Coax V S485 S485 connection details (Star Card must be in 4 wire mode) x452/552 M- 9F M or or round must be connected with S2 M igital Sprite/SL/S2 S485 Wiring details Camera 1 C Head Camera 2 C Head Camera 3 C Head x552 ddress 1 erminated x452 ddress 2 erminated x552 ddress 3 erminated ddress 4 ddress 5 erminated Key S485 Coax M or + or - S485 connection details (Star Card must be in 4 wire mode) x452/552 V S485 X+ X- X- X+ LY LY VX S485 P SW1 - Pelco, 2400,,8,1 IMP Set each camera to Pelco Spectra II within the VX setup then set the protocol converter SW1 switch as shown and SW2 to the required dome protocol. Protocol converter switch settings for VCL conversion. SW2 - VCL 9600,,8,1 Starcard/Protocol converter when used with Integral echnologies VX S485 Star Card Manual V7 4 Mar 2003.doc Page 17/17