36V 18 ~ 36V 16A 15A 12A 10A 8A 6.7A 5.72A 5A 20V 10 ~ 20V 24V 12 ~ 24V 192W 225W 240W 240W 240W 241.2W 240.2W 240W.

Transcription

1 40W Single Output Switching Power Supply IP65 IP67 HLG-40 series SPECIFICATION MODEL HLG-40- HLG-40-5 HLG-40-0 HLG-40-4 HLG HLG HLG-40-4 HLG OUTPUT INPUT PROTECTION ENVIRONMENT SAFETY & EMC OTHERS NOTE DC VOLTAGE CONSTANT CURRENT REGION Note.4 6 ~V RATED CURRENT RATED POWER VOLTAGE ADJ. RANGE Note.6. ~.8V CURRENT ADJ. RANGE LINE REGULATION LOAD REGULATION SETUP, RISE TIME HOLD UP TIME (Typ.) VOLTAGE RANGE FREQUENCY RANGE POWER FTOR EFFICIENCY (Typ.) CURRENT INRUSH CURRENT (Typ.) LEAKAGE CURRENT OVER CURRENT OVER VOLTAGE OVER TEMPERATURE WORKING TEMP. WORKING HUMIDITY SAFETY STANDARDS WITHSTAND VOLTAGE ISOLATION RESISTANCE EMS IMMUNITY MTBF Note.8 500ms, 80ms at full load Note.5 STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION V RIPPLE & NOISE (max.) Note. 50mVp-p VOLTAGE TOLERANCE Note.3 SHORT CIRCUIT 5V 7.5 ~ 5V 0V 0 ~ 0V 4V ~ 4V 95 ~ 08% Note.4 Protection type : Constant current limiting, recovers automatically after fault condition is removed Note.7 UL0, TUV EN6347-, EN independent (except for HLG-40H C type), UL60950-, UL8750, TUV EN60950-, IP65 or IP67 approved -:3.75KV -FG:.88KV -FG:0.5KV -, -FG, -FG:00M Ohms / 500VDC / 5 / 70% RH DIMENSION 44.*68*38.8mm (L*W*H)(HLG-40-Blank/A/B) 5*68*38.8mm (L*W*H)(HLG-40-C) PKING.3Kg; pcs/6.6kg/0.74cuft(hlg-40-blank/a/b).3kg; pcs/5.8kg/.6cuft(hlg-40-c) 30V 5 ~ 30V 36V 8 ~ 36V 6A 5A A 0A 8A 6.7A 5.7A 5A 48V 4 ~ 48V 9W 5W 40W 40W 40W 4.W 40.W 40W 8 ~ 6A.5% 50mVp-p 4 ~ 6V 7.5 ~ 5A.0% 50mVp-p 8.6 ~.4V 6 ~ A 50mVp-p.4 ~ 5.6V 5 ~ 0A 00mVp-p 8 ~ 3V Can be adjusted by internal potential meter or through output cable 4 ~ 8A 50mVp-p 33.5 ~ 38.5V 3.3 ~ 6.7A 50mVp-p 44.8 ~ 5.V.5 ~ 5A 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5%.0%.5% 0.5% 0.5% 0.5% 0.5% 0.5% 5ms at full load 30V /5V 90 ~ 64V 7 ~ 373VDC 47 ~ 63Hz 30V /5V PF 0.95/30V PF 0.98/5V at full load and rated output voltage PF 0.9 at 65 ~ 00% load 90% 90% 9% 93% 93% 93.5% 94% 94% 94% 4A / 5V A / 30V COLD START 75A/30V <0.75mA / 40V Hiccup mode, recovers automatically after fault condition is removed. 3.5 ~ 6V 6.5 ~ 9.5V ~ 6V 6 ~ 33V 3.5 ~ 36.5V 40 ~ 48V 46 ~ 50V 59 ~ 65V 59 ~ 65V Protection type : Shut down and latch off o/p voltage, re-power on to recover 05 5 (TSW) 95 5 (TSW) Protection type : Shut down o/p voltage, recovers automatically after temperature goes down -30 ~ full load ; 60% load (Refer to derating curve) 0 ~ 95% RH non-condensing -40 ~ +80, 0 ~ 95% RH 0.03%/ (0 ~ 50 ) 0 ~ 500Hz, 5G min./cycle, period for 7min. each along X, Y, Z axes EMI CONDUCTION & RADIATION Compliance to EN5505, EN550 (CISPR) Class B HARMONIC CURRENT Compliance to EN Class C ( 50% load) ; EN Compliance to EN ,3,4,5,6,8,; ENV5004, EN6547, EN5504, heavy industry level (surge 4KV), criteria A 07.9Khrs min. MIL-HDBK-7F (5 ) 4V ~ 4V 50mVp-p 39 ~ 45V.86 ~ 5.7A HLG V 7 ~ 54V 4.45A 40.3W 350mVp-p 50 ~ 57V.3 ~ 4.45A 0.5% 0.5%

2 40W Single Output Switching Power Supply HLG-40 series Mechanical Specification Blank:(HLG-40) Case No.954C Unit:mm /L(Brown) /N(Blue) FG (Green/Yellow) A Type:(HLG-40-_A) /L(Brown) /N(Blue) FG (Green/Yellow) SJTW 8AWG(0.75mm ) 3C IP67 rated. Cable for I/O connection. SJTW 8AWG(0.75mm ) 3C Vo Io ADJ. ADJ. 4. 4PL 4. 4PL SJTW 4AWG(.5mm ) C SJTW 4AWG(.5mm ) C +V(Red) -V(Black) V(Red) -V(Black) IP65 rated. Output voltage and constant current level can be adjusted through internal potential meter. (Can access by removing the rubber stopper on the case.) File Name:HLG-40-SPEC

3 40W Single Output Switching Power Supply HLG-40 series B Type:(HLG-40-_B) /L(Brown) /N(Blue) FG (Green/Yellow) SJTW 8AWG(0.75mm ) 3C SJTW 4AWG(.5mm ) C SJTW 8AWG(0.75mm ) C 4. 4PL +V(Red) -V(Black) ADJ(Blue) ADJ(White) 38.8 IP67 rated. Output constant current level can be adjusted through output cable by connecting a resistor between ADJ and ADJ. Reference resistance value for output current adjustment (Typical) Percentage of rated current Slightly > 00% 75% 50% Slightly < 50% Model V 5V 0V 4V 30V 36V 4V 48V 54V Open Open Open Open Open Open Open Open Open K Short Short Short Short Short Short Short Short Short C Type:(HLG-40-_C) Vo Io ADJ. ADJ. 4. 4PL Input Terminal Pin No. Pin No. 3 FG /L /N DC Output Terminal Pin No Pin No. -V +V Output voltage and constant current level can be adjusted through internal potential meter. (Can access by removing the rubber stopper on the case.) File Name:HLG-40-SPEC

4 40W Single Output Switching Power Supply HLG-40 series Block Diagram Fosc : 00KHz FG EMI FILTER & RECTIFIERS PFC CIRCUIT PFC CONTROL O.L.P. POWER SWITCHING PWM & PFC CONTROL RECTIFIERS & FILTER O.L.P. DETECTION CIRCUIT O.V.P. +V -V ADJ ADJ (B Type) Derating Curve Static Characteristics fosc : 00KHz V V 70 LOAD (%) 40 0 LOAD (%) AMBIENT TEMPERATURE ( ) Power Factor Characteristic (HORIZONTAL) INPUT VOLTAGE (V) 60Hz PF Power factor will be higher than 0.9 when output loading is 65% or higher Constant Current Mode 3 0 % 4 0 % 5 0 % 6 0 % 7 0 % 8 0 % 9 0 % 0 0 % 0V 30V LOAD EFFICIENCY vs LOAD (48V Model) HLG-40 series possess superior working efficiency that up to 94% can be reached in field applications EFFICIENCY (%) V 30V % 0% 0% 30% 40% 50% 60% 70% 80% 90% 00% LOAD File Name:HLG-40-SPEC

5 40W Single Output Switching Power Supply HLG-40 series DRIVING METHODS OF LED MODULE There are two major kinds of LED drive method "direct drive" and "with LED driver". A typical LED power supply may either work in "constant voltage mode (CV) or constant current mode (CC)" to drive the LEDs. Mean Well's LED power supply with CV+ CC characteristic can be operated at both CV mode (with LED driver, at area (A) and CC mode (direct drive, at area (B). 00 Vo(%) (A) Constant Voltage area (B) Constant Current area 50 (max.) (C) Hiccup Protection Io (%) Typical LED power supply I-V curve Direct driving : Under direct driving, the power supply will work in "constant current mode (CC)" and output voltage of the power supply will be clamped by sum of forward voltage (V F) of the LED strip. The total forward voltage of series connecting LEDs is suggested for 75%~95% of power supply rated output voltage due to concern of the best PF value and efficiency. ~ HLG-40 With LED driver Using additional driver, the power supply will work in "constant voltage mode (CV)" and output voltage of the power supply will be kept in rated value. In this drive mode, several design issues need to be considered:.output voltage of PSU must be higher than total forward voltage of series connecting LEDs by 3V minimum..input capacitor (Cin) of LED driver circuit should use.uf ~ uf(typ.) of rating depends on the operating frequency of the LED driver. The higher the operating frequency is used, the smaller value of Cin should be chosen, and vice versa. HLG-40 R Cin Cout VF L ~ IC Circuit File Name:HLG-40-SPEC

6 40W Single Output Switching Power Supply HLG-40 series EMI DEBUG SUGGESTION C LED CC driver Chassis of LED Lamp HLG-40 CC IC ~ FG B A D A A. Add a common mode ferrite choke on output wires to reduce the common emission between 0M ~ 300MHz per lighting EMI regulation. B. Chassis of LED lamp and chassis of HLG-40 or the FG wire should be connected to the safety ground to reduce the EMI noise, including the conduction and radiation emission. C. The additional X-Cap and discharge resistor can reduce the low frequency conduction noise between 9K ~ MHz per lighting EMI regulation. D. L-C filter should be added at the DC input of LED constant current driver to avoid the differential emission and high frequency noise generated by the CC driver. WATERPROOF CONNECTION Waterproof connector Waterproof connector can be assembled on the output cable of HLG-40 to operate in wet/damp or outdoor environment. HLG-40 Size Pin Configuration (Female) Size Pin Configuration (Female) M Order No. Suitable Current 4-PIN 5A/PIN M-04 0A max. 5-PIN 5A/PIN M-05 0A max. M5 Order No. Suitable Current -PIN A/PIN M5-0 A max. LED Lamp Cable Joiner Suitable for 4AWG~AWG 5 Up to four wires can be connected through this cable joiner by soldering or clamping by tools. LED Lamp HLG-40 Wires File Name:HLG-40-SPEC