2 x 15 LED STEREO VU-METER
|
|
- Franklin Little
- 5 years ago
- Views:
Transcription
1 Total solder points: 271 Difficulty level: beginner advanced K x 15 LED STEREO VU-METER For visualization of audio signals. Can be used with Velleman mixing panel. Use with mixing panels, amplifiers, car audio systems Easily connects to the line-level output (LOW INPUT) from any tape deck, stereo system, or CD player. A special input (HIGH INPUT) is provided, so that the unit can directly be connected to the speaker output of most systems*. To make it universal, the readout can be set as DOT or BAR indication. The supplied display window for vertical or horizontal mounting, makes the unit very attractive. If wanted, the unit can be calibrated by the means of a trim potentiometer. *NOT SUITED FOR CONNECTION TO HIGH POWER CAR STEREO SYSTEM Specifications Bar or dot readout. Scale: -23dB to 5dB, 15 LED s per channel. db-linear division from -4 to 5dB (1dB per led). Systematically growing steps below -4dB. Accuracy: ±0.5dB (1KHz). Frequency range: 20Hz to 30KHz (-3dB). Three different LED colors: green, orange and red. Adjustable input sensitivity: 150mV to 5Vrms Low input 1.5V to 50Vrms High input Input impedance: 47K Low input / 470K High input Power supply: 12 to 15VDC / 300mA Dimensions: 150 x 57mm modifications reserved PARTLIST H4306P-ED1
2 5% 1% COLOR= 2 5 4K7= ( B ) 4K7= ( ) C O D E I P E SF S DK N D GB F NL CODIGO CODIGO VÄRI FÄRG FARVE FARGE FARB COLOUR DE DE KOODI SCHEMA CODE KODE KODE KODE CORES COLORES CODICE COLORE CODIFI- CATION DES COU- LEURS KLEUR KODE C O D E 0 Nero Preto Negro Musta Svart Sort Sort Schwarz Black Noir Zwart 0 1 Marrone Castanho Marrón Ruskea Brun Brun Brun Braun Brown Brun Bruin 1 2 Rosso Encarnado Rojo Punainen Röd Rød Rød Rot Red Rouge Rood 2 3 Aranciato Laranja Naranjado Oranssi Orange Orange Orange Orange Orange Orange Oranje 3 4 Giallo Amarelo Amarillo Keltainen Gul Gul Gul Gelb Yellow Jaune Geel 4 5 Verde Verde Verde Vihreä Grön Grøn Grønn Grün Green Vert Groen 5 6 Blu Azul Azul Sininen Blå Blå Blå Blau Blue Blue Blauw 6 7 Viola Violeta Morado Purppura Lila Violet Violet Violet Purple Violet Paars 7 8 Grigio Cinzento Gris Harmaa Grå Grå Grå Grau Grey Gris Grijs 8 9 Bianco Branco Blanco Valkoinen Vit Hvid Hvidt Weiss White Blanc Wit 9 A Argento Prateado Plata Hopea Silver Sølv Sølv Silber Silver Argent Zilver A B Oro Dourado Oro Kulta Guld Guld Guldl Gold Gold Or Goud B
3 ASSEMBLY STEPS Required tools to assemble the kit: Use a small soldering iron of max. 40W. Use thin (1mm) solder, do not use any flux. Use a small cutter to trim the excess wires Mount the components against the PCB surface and carefully solder the leads in place. Obtain cone- shaped, shiny soldered joints by heating up the component leads sufficiently. This solder joint gives a bad connection. Trim the excess wires up to the level of the solder Careless assembly will certainly lead to troubles. Insert the part, oriented correctly, into its correct holes on the PCB. Mount the components in the correct order as stated in this manual. The component values in the diagram are for reference only. The values in this partlist are correct and must be followed. Use the boxes to tick off your progress. Before starting to build, also read the general guidelines 3
4 Assembly Mount all components onto the PC board. 1. JUMPERS 2. MODE SELECTION JUMPERS J1 J2 J3 J4 J5 J6 J7 J8 J9 J10 J11 For BAR readout mount the JB jumpers or for DOT readout mount the JD jumpers. BAR DOT Left dB Right Left dB Right JB1 JD1 JB2 JD2 JB3 JB4 4
5 3. DIODES (Check the polarity!) 5. 1% METALFILM RESISTORS CATHODE D... R... D1: 1N4148 D2: 1N4148 D3: 1N4148 D4: 1N4148 D5: 1N4148 D6: 1N4148 D7: 1N4148 D8: 1N4148 D9: 1N N ZENER DIODE (Check the polarity!) R1: 3K ( ) R2: 3K9 ( ) R3: 3K ( ) R4: 3K9 ( ) 6. ¼W RESISTORS R... CATHODE ZD1: 6V2 ZD... R5: 470K ( B) R6: 47K ( B) R7: 47K ( B) R8: 470K ( B) R9: 47K ( B) R10: 47K ( B) R11: 2K2 ( B) R12: 18K ( B) R13: 18K ( B) R14: 2K2 ( B) R15: 1K ( B) R16: 1K ( B) R17: 2K2 ( B) R18: 2K2 ( B) R19: 2K2 ( B) R20: 330 ( B) 5
6 7. IC SOCKETS (Check the position of the notch!) 9. 1W RESISTORS R... 1 IC... 2mm IC1: 8P IC2: 8P IC3: 18P IC4: 18P IC5: 18P IC6: 18P 8. RESISTOR TRIMMERS R21: 47 ( B) R22: 47 ( B) 10. CAPACITORS C... RV... C1: 220n (224 - µ22) C2: 220n (224 - µ22) C3: 220n (224 - µ22) RV1: 250K (220K) RV2: 250K (220K) 6
7 11. ELECTROLYTIC CAPACITOR (Check the polarity!) C4: 470µ C5: 47µ C6: 47µ C7: 470µ C LED s (Check the polarity!) (Mount the LED s at correct height) COLOR = LD12: green (5) LD13: green (5) LD14: green (5) LD15: green (5) LD16: green (5) LD17: green (5) LD18: green (5) LD19: green (5) LD20: green (5) LD21: yellow (4) LD22: yellow (4) LD23: yellow (4) LD24: yellow (4) LD25: red (2) LD26: red (2) LD27: red (2) LD28: red (2) LD29: red (2) LD30: red (2) 13. IC s (Check the position of the notch!) LD... 1 CATHODE 13mm PIN 1 IC... LD1: green (5) LD2: green (5) LD3: green (5) LD4: green (5) LD5: green (5) LD6: green (5) LD7: green (5) LD8: green (5) LD9: green (5) LD10: green (5) LD11: green (5) IC1: 741 IC2: 741 IC3: LM3916 IC4: LM3916 IC5: LM3916 IC6: LM3916 7
8 Mount the unit in a suitable housing or on a suitable panel 14. DRILL PATTERN FRONT PANEL Ø Mount spacers onto the front panel 6mm M3 COUNTERSUNK-HEAD BOLT 10mm M3 SPACER LOCK WASHER 6mm M3 COUNTERSUNK-HEAD BOLT 2...3mm FRONTPANEL SHAKEPROOF WASHER 10mm M3 SPACER 8
9 16. Mount the PCB onto the front panel 4mm M3 BOLT 6mm M3 COUNTERSUNK-HEAD BOLT 2...3mm FRONTPANEL SHAKEPROOF WASHER 10mm M3 SPACER PCB 4mm M3 BOLT 9
10 Connect the unit to a suitable signal, this can be line level (LOW input) 17. Connecting to a line level output of a preamplifier and connecting a power supply from 12 to 15VDC / 300mA TAPE L OUT R FROM AUDIO AMPLIFIER HI LEFT LO LO HI RIGHT V K4306 MAINS MAINS 1N V/300mA 12V/300mA 1N V/300mA 1000uF/25V 1000uF/25V VDC POWER SUPPLY Connect the unit to a suitable supply voltage between 12VDC and 15VDC, this can be a standard DC adapter. You can also build your own power supply, see diagram. Use a 2x12V transformer, two rectifier diodes and a electrolytic capacitor or use a single 12V transformer with a bridge rectifier and a electrolytic capacitor. 10
11 Connect to a speaker level (HIGH input) 18. Connecting to a speaker level output and connecting a power supply from 12 to 15VDC / 300mA L LEFT SPEAKER L- INPUT (0) R- RIGHT SPEAKER R FROM POWER AMPLIFIER HI LEFT LO LO HI RIGHT V K4306 MAINS MAINS 1N V/300mA 12V/300mA 1N V/300mA 1000uF/25V 1000uF/25V VDC POWER SUPPLY Connect the unit to a suitable supply voltage between 12VDC and 15VDC, this can be a standard DC adapter. You can also build your own power supply, see diagram. Use a 2x12V transformer, two rectifier diodes and a electrolytic capacitor or use a single 12V transformer with a bridge rectifier and a electrolytic capacitor. 11
12 19. Connecting to a car radio LEFT SPEAKER R- RIGHT SPEAKER R CAR RADIO L L- 12V ANTENNE POWER OUT HI LO LEFT LO HI RIGHT V K4306 REMARK: Do not connect the unit to a high power car booster or car stereo, this equipment uses isolated ground connection. The connection to this kind of amplifier can cause permanent damage to the amplifier or car radio! 20. Connecting into Velleman mixing panel K4306 RIGHT V LO LEFT LO V VU R OUT L L R -V V EFF MON REC OUT VELLEMAN K2664 Adjust the unit sensitivity according to your satisfactions by means of the trim potentiometer RV1 and RV2. 12
13 21. PCB 13
K LED MONO VU METER
Total solder points: 93 Difficulty level: Beginner 1 2 3 4 5 Advanced K4304 10 LED MONO VU METER For instant visualization of audio signal levels. Easy hook up to a LINE level ( LOW input) signal source.
More informationMX2 Dual Digital Electric Handpiece [ ] for Procenter Delivery Units (12:00 mounted)
MX2 Dual Digital Electric Handpiece [153900-008] for Procenter Delivery Units (12:00 mounted) Contents: Installation... 1 Language of origin: English Note Confirm the desired position to install the MX2
More informationEXTENDED RECORD PLAYBACK KIT. Allows you to record and play messages of up to 8 minutes long.
K8094P 1 ILLUSTRATED LUS TED ASSEMBLY MANUAL AL H8094IP 1 EXTENDED RECORD PLAYBACK KIT Allows you to record and play messages of up to 8 minutes long. The K8094 allows you to record and play messages of
More informationTotal solder points: 240 Difficulty level: beginner advanced LIGHT COMPUTER K5201 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 240 Difficulty level: beginner 1 2 3 4 5 advanced LIGHT COMPUTER K5201 16 different patterns and 7 outputs provide a unique light show. ILLUSTRATED ASSEMBLY MANUAL H5201IP-1 Features
More informationKAA Watt x 2 Class-D Audio Amplifier Kit
KAA10021 50 Watt x 2 Class-D Audio Amplifier Kit This amplifier kit uses Texas Instruments TPA3116D2 stereo audio amplifier IC for driving speakers up to 50 watts @ 4 ohm per channel in stereo mode and
More informationUSB Controlled DMX interface
USB Controlled DMX interface Control DMX fixtures using a PC and USB interface. Stand-alone test function that outputs all 512 channels at a time, with adjustable levels. Total solder points: 117 Difficulty
More informationK2579 UNIVERSAL START/STOP TIMER. Specifications
Total solder points: 49 Difficulty level: beginner 1 2 3 4 5 advanced UNIVERSAL START/STOP TIMER K2579 Small size timer provides up to 60 minutes delay. Specifications Relay output with switchover contact.
More informationK8099 NIXIE CLOCK. * optional enclosure TKOK19 (black) - TKOK17 (white) ** optional plexiglass enlcosure B8099 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 230 + 74 Difficulty level: beginner 1 2 3 4 5 advanced NIXIE CLOCK K8099 ** * A unique combination of both vintage and modern electronics ILLUSTRATED ASSEMBLY MANUAL H8099IP-1 * optional
More informationGeneral guidelines for assembly, safety and electromagnetic compatibility
General guidelines for assembly, safety and electromagnetic compatibility For more info about all our kits, please visit our Web-site : http://www.velleman.be While the soldering iron is heating, read
More informationK8086 TELEPHONE RING DETECTOR WITH RELAY OUTPUT. Simply connect in parallel with phone line. ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 61 Difficulty level: beginner 1 2 3 4 5 advanced TELEPHONE RING DETECTOR WITH RELAY OUTPUT K8086 Simply connect in parallel with phone line. Accepts standard adaptor & telephone plug.
More informationTotal solder points: 82 Difficulty level: beginner advanced 2 MODULAR DIGITS WITH SERIAL INTERFACE K8063 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 82 Difficulty level: beginner 1 2 3 4 5 advanced 2 MODULAR DIGITS WITH SERIAL INTERFACE K8063 Multiple units can be linked in an easy way to create larger readouts for e.g. Score-keeping,
More informationMAIN PCB (The small one with the square cut out from one side)
THANKS FOR CHOOSING ONE OF OUR KITS! This manual has been written taking into account the common issues that we often find people experience in our workshops. The order in which the components are placed
More informationHigh Power (15W + 15W) Stereo Amplifier
High Power (15W + 15W) Stereo Amplifier Build Instructions Issue 1.0 Build Instructions Before you put any components in the board or pick up the soldering iron, just take a look at the Printed Circuit
More informationDMX CONTROLLED RELAY K8072
Total solder points: 167 Difficulty level: beginner 1 2 3 4 5 advanced DMX CONTROLLED RELAY K8072 f the means o ol. y b y la a re 2 protoc Control DMX51 wn well-kno ILLUSTRATED ASSEMBLY MANUAL Total solder
More informationONE CHANNEL DUAL OUTPUT RECEIVER
Total solder points: 89 Difficulty level: beginner 1 2 3 4 5 advanced ONE CHANNEL DUAL OUTPUT RECEIVER For use with K8058 / VM118R transmitters. K8070 A single transmitter key-press activates two independent
More information15 Channel IR transmitter. Total solder points: 53 Difficulty level: beginner advanced K8049 ILLUSTRATED ASSEMBLY MANUAL
15 Channel IR transmitter Compatible with most Velleman IR receiver kits, 4 adresses allow the use of multiple receivers in one room. Total solder points: 53 Difficulty level: beginner 1 2 3 4 5 advanced
More informationKDS Channel DMX Controlled Servo Kit
KDS00801 8-Channel DMX Controlled Servo Kit This is a DMX512-A controlled servo kit using ANSI approved RJ-45 connectors for DMX networks. Power requirements are 8-20 VDC @ 50 ma. The board features an
More informationKDR00101 DMX Controlled Relay Kit
KDR00101 DMX Controlled Relay Kit This is a DMX512-A relay kit using ANSI approved RJ-45 connectors for DMX networks. Power requirements are 12 Vdc @ 100 ma. The relay contact rating is 10 Amp @ 120 or
More informationK8086 TELEPHONE RING DETECTOR WITH RELAY OUTPUT. Simply connect in parallel with phone line. ILLUSTRATED ASSEMBLY MANUAL H8086IP-1
Total solder points: 61 Difficulty level: beginner 1 2 3 4 5 advanced TELEPHONE RING DETECTOR WITH RELAY OUTPUT K8086 Simply connect in parallel with phone line. Accepts standard adaptor & telephone plug.
More informationMAIN PCB (The small one)
THANKS FOR CHOOSING ONE OF OUR KITS! This manual has been written taking into account the common issues that we often find people experience in our workshops. The order in which the components are placed
More informationKDR00301 DMX Controlled Relay Kit
KDR00301 DMX Controlled Relay Kit This is a DMX512-A relay kit using ANSI approved RJ-45 connectors for DMX networks. Power requirements are 12 Vdc @ 200 ma. The relay contact rating is 10 Amp @ 120 or
More informationQRPGuys Digital Dial/Frequency Counter
QRPGuys Digital Dial/Frequency Counter First, familiarize yourself with the parts and check for all the components. If a part is missing, please contact us and we will send one. You must use qrpguys.parts@gmail.com
More informationAssembly Guide. LEDs. With these assembly instructions, you can easily build your own SWT16. All required components are included in this kit.
Assembly Guide With these assembly instructions, you can easily build your own SWT16. All required components are included in this kit. You need the following tools: soldering iron, wire cutter and solder.
More informationDELUXE STEREO AMPLIFIER KIT
ESSENTIAL INFORMATION BUILD INSTRUCTIONS CHECKING YOUR PCB & FAULT-FINDING MECHANICAL DETAILS HOW THE KIT WORKS CREATE YOUR OWN SPEAKER DOCK WITH THIS DELUXE STEREO AMPLIFIER KIT Version 2.0 Build Instructions
More information8 CHANNEL USB RELAY CARD
8 CHANNEL USB RELAY CARD Use your computer USB port to connect to the outside world. Total solder points: 363 Difficulty level: beginner 1 2 3 4 5 advanced K8090 ILLUSTRATED ASSEMBLY MANUAL H8090IP-1 Features
More informationStep 1 - Modifying the power-supply from 12 to 16 Volts Increasing the power-supply voltage to 16V increases the headroom and reduces distortion. Also
Dada Electronics - Quad 33 Revision - Illustrated Guidelines V 2.4 First of all, thanks for your purchase of our upgrade kit! Hereunder, you will find the step-by-step guidelines for upgrading the Quad
More informationElectronics Construction Manual
Electronics Construction Manual MitchElectronics 2018 Version 1 07/05/2018 www.mitchelectronics.co.uk CONTENTS Introduction 3 How To Solder 4 Resistors 5 Capacitors 6 Diodes and LEDs 7 Switches 8 Transistors
More informationUniversal Keying Adapter 3+
Universal Keying Adapter 3+ The Universal Keying Adapter Version 3+ kit will allow you to key nearly any transmitter or transceiver with a straight key, electronic keyer, computer serial or parallel port
More informationPacific Antenna Two Tone Generator
Pacific Antenna Two Tone Generator Description Our Two Tone Generator kit provides two non-harmonic, sine wave signals for testing audio circuits Outputs of approximately 700Hz and 1900Hz and the combination
More informationInstallation/assembly manual for DCC/Power shield
Installation/assembly manual for DCC/Power shield The DCC circuit consists of the following components: R1/R6 R2/R3 R4/R5 D1 C2 2 kω resistor ½ Watt (colour code Red/Black/Black/Brown/Brown) 10 kω resistor
More informationCP5176 Assembly guide. Soldering. CP5176 Assembly guide Main PCB PCB split. Document revision 2.1 Last modification : 12/11/17
CP5176 Assembly guide Safety warning The kits are main powered and use potentially lethal voltages. Under no circumstance should someone undertake the realisation of a kit unless he has full knowledge
More informationQRPometer Assembly Manual Copyright 2012 David Cripe NM0S The 4 State QRP Group. Introduction
QRPometer Assembly Manual Copyright 2012 David Cripe NM0S The 4 State QRP Group Introduction Thank you for purchasing a QRPometer. We hope you will enjoy building it and and find it a useful addition to
More informationsolutions for teaching and learning
RKAmp1 Component List and Instructions PCB layout Constructed PCB Schematic RKAmp1 Stereo Amplifier Page 1 Description The RKAmp1 stereo amplifier PCB has been designed around the 2 x 1watt stereo amplifier
More informationRC210 Repeater Controller Assembly Manual
Arcom Communications 24035 NE Butteville Rd Aurora, Oregon 97002 (503) 678-6182 arcom@ah6le.net http://www.arcomcontrollers.com/ RC210 Repeater Controller Assembly Manual Hardware Version 3.3 Reproduction
More informationChill Interface PCB Assembly Instructions
ExcelValley Chill Interface PCB Waveblaster Module MIDI Interface Board Chill Limited Edition V2 Assembly Kit Standalone midi interface board for Waveblaster synthesizer modules. Suitable for most Waveblaster
More informationRC-210 Repeater Controller Assembly Manual
Arcom Communications 24035 NE Butteville Rd Aurora, Oregon 97002 (503) 678-6182 arcom@ah6le.net RC-210 Repeater Controller Assembly Manual Hardware Version 3.0 Original Release Date September 13, 2004
More informationAdvanced Strobe 1.0 Kit
Kit Instruction Manual Eastern Voltage Research, LLC December 2013, Rev 1 1 http://www.easternvoltageresearch.com Kit Introduction to the Kit Thank you for purchasing the Kit. If you are looking for a
More informationSRI-02 Speech Recognition Interface
SRI-02 Speech Recognition Interface Data & Construction Booklet The Speech Recognition Interface SRI-02 allows one to use the SR-07 Speech Recognition Circuit to create speech controlled electrical devices.
More informationRC-210 Repeater Controller Assembly Manual
Arcom Communications 24035 NE Butteville Rd Aurora, Oregon 97002 (503) 678-6182 arcom@ah6le.net RC-210 Repeater Controller Assembly Manual Hardware Version 2.5 Reproduction or translation of any part of
More informationElectronics Construction Manual
Electronics Construction Manual MitchElectronics 2019 Version 3 04/02/2019 www.mitchelectronics.co.uk CONTENTS Introduction 3 How To Solder 4 Resistors 5 Capacitors 6 Diodes and LEDs 7 Switches 8 Transistors
More informationAssembly Instructions for the KA Electronics Elliptic Equalizer
Assembly Instructions for the KA Electronics Elliptic Equalizer Install IC sockets Elliptic Equalizer PC Board Stuffing Guide Place the PC Board on the work bench silkscreen side face up. Place twelve
More informationIR TRANSMITTER BLOK PCB ASSEMBLY INSTRUCTIONS. Copyright EduTek Ltd Rev. 2
IR TRANSMITTER BLOK PCB ASSEMBLY INSTRUCTIONS Copyright EduTek Ltd Rev. 2 Circuit Details The circuit is shown below with a parts list of components. Check through this list and identify each component.
More informationMP3 audio amplifier. Build Instructions. Issue 2.0
MP3 audio amplifier Build Instructions Issue 2.0 Build Instructions Before you put any components in the board or pick up the soldering iron, just take a look at the Printed Circuit Board (PCB). The components
More informationK6000 MICROPROCESSOR CONTROLLER / TIMER ASSEMBLY 3 H6000B-ED2
K6000 MICROPROCESSOR CONTROLLER / TIMER ASSEMBLY 3 H6000B-ED2 VELLEMAN KIT NV Legen Heirweg 33 9890 Gavere Belgium http://www.velleman.be 2 MICRO PROCESSOR CONTROLLER/TIMER In addition to the features
More informationAssembly Instructions for the KA Electronics IGFO Input Gain Filter Output Board
Assembly Instructions for the KA Electronics IGFO Input Gain Filter Output Board IGFO PC Board Stuffing Guide Install IC sockets Place the PC Board on the work bench silkscreen side face up. Place ten
More informationPacific Antenna Easy TR Switch Kit
Pacific Antenna Easy TR Switch Kit Kit Description The Easy TR Switch is an RF sensing circuit with a double pole double throw relay that can be used to automatically switch an antenna between a separate
More informationPost Tenebras Lab. Written By: Post Tenebras Lab
Post Tenebras Lab PTL-ino is an Arduino comptaible board, made entirely out of through-hole components. It is a perfect project to learn how to solder and start getting into the world of micro controllers.
More informationRECORD & PLAYBACK KIT
ESSENTIAL INFORMATION BUILD INSTRUCTIONS CHECKING YOUR PCB & FAULT-FINDING MECHANICAL DETAILS HOW THE KIT WORKS ADD AN AUDIO MESSAGE TO YOUR PRODUCT WITH THIS RECORD & PLAYBACK KIT Version 2.1 Build Instructions
More informationsolutions for teaching and learning
RKAmp3 Component List and Instructions PCB layout Constructed PCB Schematic RKAmp3 Stereo Amplifier Page 1 Description The RKAmp3 stereo amplifier PCB has been designed around the 2 x 7watt stereo amplifier
More informationImages Scientific OWI Robotic Arm Interface Kit (PC serial) Article
Images Scientific OWI Robotic Arm Interface Kit (PC serial) Article Images Company Robotic Arm PC Interface allows real time computer control and an interactive script writer/player for programming and
More informationAdvanced Lantern 1.0 Kit. Introduction to the Advanced Lantern 1.0 Kit
Advanced LED Lantern 1.0 Instruction Manual Eastern Voltage Research, LLC Introduction to the Advanced Lantern 1.0 Kit Thank you for purchasing the Advanced Lantern 1.0 Kit. This kit is an advanced microprocessor
More informationThese are the illustrated step-by-step guidelines for upgrading your Quad 306 with the Dada Electronics upgrade-kit.
Quad 306 DIY illustrated guidelines version 1.1 These are the illustrated step-by-step guidelines for upgrading your Quad 306 with the Dada Electronics upgrade-kit. We will replace all electrolytic capacitors,
More informationPicoTurbine Mark 8.3 Generator Field Controller Kit
PicoTurbine Mark 8.3 Generator Field Controller Kit Based on a design published in Home Power magazine by Richard Perez. Used with permission. Reprint of original article included with kit. An easy-to-build
More informationLushOne Inca Synth Module Build Instructions
LushOne Inca Synth Module Build Instructions Getting started If you can build the LushOne base module then then building the Inca should be easy Remember: Accuracy and neatness is more important than speed
More informationStep 1 The tools & the Components The tools you need: A good quality soldering iron with a fine point (max 30) Watt or a soldering-station. A desolder
Upgrade/revision manual Quad 44 pre amplifier. V2.5 These are the illustrated step-by-step guidelines for upgrading your Quad 44 with the Dada Electronics upgrade-kits. The Quad 44 preamp was the first
More informationXYLOPHONE KIT ESSENTIAL INFORMATION. Version 2.0 CREATE YOUR OWN ELECTRONIC MUSICAL INTRUMENT WITH THIS
ESSENTIAL INFORMATION BUILD INSTRUCTIONS CHECKING YOUR PCB & FAULT-FINDING MECHANICAL DETAILS HOW THE KIT WORKS CREATE YOUR OWN ELECTRONIC MUSICAL INTRUMENT WITH THIS XYLOPHONE KIT Version 2.0 Build Instructions
More informationTuBbika SMR-4-PLUS voicecard
TuBbika SMR-4-PLUS voicecard Assembly instructions We assume you know soldering. If you don t, look first at this tutorial. Be patient! And if you have any doubt, head to the forum never be afraid to ask!
More informationPICAXE EXPERIMENTER BOARD (AXE090)
(AXE00) Description: The PICAXE experimenter board allows circuits for any size/revision of PICAXE chip ( / / ) to be quickly tested using a prototyping breadboard. The experimenter board provides power
More informationNoise Source Model 9751 Assembly and Using Manual
Noise Source Model 9751 Assembly and Using Manual This second-generation 9700-series processing element for modular sound synthesizers is designed to provide great sound and excellent value. This module
More informationQUASAR ELECTRONICS KIT No Hi-Fi PREAMPLIFIER WITH REMOTE CONTROL
QUASAR ELECTRONICS KIT No. 1070 Hi-Fi PREAMPLIFIER WITH REMOTE CONTROL General Description This is a hi-fi STEREO preamplifier based on a single integrated circuit which employs a revolutionary new method
More informationSchematic Diagram: R2,R3,R4,R7 are ¼ Watt; R5,R6 are 220 Ohm ½ Watt (or two 470 Ohm ¼ Watt in parallel)
Nano DDS VFO Rev_2 Assembly Manual Farrukh Zia, K2ZIA, 2016_0130 Featured in ARRL QST March 2016 Issue Nano DDS VFO is a modification of the original VFO design in Arduino Projects for Amateur Radio by
More informationSTAGE INTERCOM KIT 1.1 SPECIFICATION. General: The lower section is a small power amplifier designed to drive headphones or a small 8ohm speaker.
STAGE INTERCOM KIT Version 2.1.1 - March 2018 - EduTek Ltd 1.0 DESCRIPTION This intercom module comprises of two separate circuits sharing the same supply. The upper section is a pre-amplifier designed
More informationTKEY-1. CW touch key. (no electromechanical contacts) Assembly manual. Last update: June 20,
TKEY-1 CW touch key (no electromechanical contacts) Assembly manual Last update: June 20, 2017 ea3gcy@gmail.com Updates and news at: www.ea3gcy.com Thanks for constructing the TKEY-1A CW touch key Have
More informationAssembly Instructions IV-11 DCF, melody
This IV-11 clock is the next generation to the IV-11 Quartz, DCF, melody. This is not a beginner kit. It requires soldering experience on the IV-18 and the IV-3A board The switching power supply wall adapter
More informationGLiPIC Ver C Assembly manual Ver 1.0
GLiPIC Ver C Assembly manual Ver 1.0 Last Rev 1.1 Oct 30, 2001 Author: Ranjit Diol Disclaimer and Terms of Agreement As with any kit, only the individual parts supplied are guaranteed against defects and
More informationSolder the Harlequin, Revision F, March Solder the Harlequin - please read carefully (also the addendum!) before starting
Solder the Harlequin, Revision F, March 2014 Page 1 of 8 Solder the Harlequin - please read carefully (also the addendum!) before starting You should check the kit for completeness (see addendum). If you
More informationButton Code Kit. Assembly Instructions and User Guide. Single Button Code Entry System
Button Code Kit Single Button Code Entry System Assembly Instructions and User Guide Rev 1.0 December 2009 www.alan-parekh.com Copyright 2009 Alan Electronic Projects Inc. 1. Introduction... 4 1.1 Concept
More informationYou need the following components to assemble the Black n Wood Nixie Clock circuit board:
You need the following components to assemble the Black n Wood Nixie Clock circuit board: Quantity Designator Description 1 Battery Battery, CR1220 1 Battery Battery holder 3 Button 1, Button 2, Button
More informationVG-305A AC Traffic Light Controller Kit
Galak Electronics Electronic kits and components Website: GalakElectronics.com Email: sales@galakelectronics.com Phone: (302) 832-1978 VG-305A AC Traffic Light Controller Kit Thank you for your purchase
More informationUzebox Kit Assembly Guide
Uzebox Kit Assembly Guide V1.3 Page 1 of 18 Revision History Version Date Author Description 1.0 01-Nov-2012 A.Bourque Initial release 1.1 6-Nov-2012 A.Bourque Minor corrections 1.2 28-Jan-2014 A.Bourque
More informationInsert the male, 90 angled, 2x10 connectors into the corresponding 2x10 sockets and put them in place, flat under the PCB. Solder.
MC624 Assembly guide Safety warning The kits are main powered and use potentially lethal voltages. Under no circumstance should someone undertake the realisation of a kit unless he has full knowledge about
More informationMicrosystems. SCI-6 Sound Card Interface Kit Version 1.09 January 2015
UM Unified Microsystems SCI-6 Sound Card Interface Kit Version 1.09 January 2015 The SCI-6 interface was designed to be a low cost, high quality interface between your PC s sound card and radio transceiver.
More informationBehringerMods.com. Instructions for modification of Behringer SRC analog inputs and outputs
BehringerMods.com Instructions for modification of Behringer SRC analog inputs and outputs The following instructions will cover the details of fully modifying a unit with analog output and analog input
More informationK1EL Morse Code Practice Oscillator CPO
Features This is an oscillator not a Morse keyer Input source can be a keyer or straight key Near Sine wave tone output CPO Tone Volume Control CPO Tone Frequency Control Use headphones or external speaker
More information1214 AUDIOPHILE INPUT SELECTOR FOR STEREO PRE-AMPLIFIERS (6 INPUTS OUTPUTS, LINE AND RECORDING)
Description Quasar kit No. 1214 is part of a new line of projects that form a full stereo system which consists of the following kits Quasar kit No.1215 Quasar kit No.1216 Quasar kit No.1217 Quasar kit
More informationHARDWARE OPERATIONS MANUAL
HARDWARE OPERATIONS MANUAL Table of Contents INTRODUCTION... 2 SECTION 1: HARDWARE COMPONENT ASSEMBLIES... 2 MECHANICAL HARDWARE AND CASE... 2 PCB ASSEMBLY... 4 ISD RECORDING CIRCUIT... 5 BREADBOARD ASSEMBLY...
More informationConnecting LEDs to the ADB I/O
Application Note AN-2 By Magnus Pettersson September 26 1996 Connecting LEDs to the I/O Introduction The following notes are for those of you who are a bit inexperienced with hardware components. This
More informationAssembly Instructions for the KA Electronics RIAA EQ Monitor Switcher
Assembly Instructions for the KA Electronics RIAA EQ Monitor Switcher Install IC sockets EQ Monitor Switcher PC Board Stuffing Guide Place the PC Board on the bench silkscreen side face up. Drop eleven
More informationUsing solderless breadboards
Page 1 of 9 Using solderless breadboards This document describes how to use the solderless breadboards available in the experimental didactic lab (LED, previously LADISPE) of Politecnico di Torino. 1 Setting
More informationGSV-1A4 M12/2 M12/2. Highlights
GSV-1A4 M12/2 M12/2 Highlights Input sensitivity: 2mV/V; 4mV/V, 2 mv/v, 1mV/V, 0.5mV/V configurable via jumpers Output signals ±10V AND 12mA+-8mA on 15 pin Sub-D Integrated half and quarter bridge completion
More informationCode Practice Oscillator (CPO)
Code Practice Oscillator (CPO) Overview Many thanks for your purchase of this code practice oscillator or CPO, this guide is intended to allow you to quickly get operational. The CPO comprises an approx.
More informationMorse Code Practice Oscillator
Features Description Keyer speed range: Limited only by keying source True Sine wave tone output Tone Volume Control Tone Frequency Control Internal Speaker 1/8 External Speaker/Headphone Jack RCA Key
More informationIC-I AND IC-I F GENERAL DESCRIPTION SPECIFICATIONS. Output Impedance: Phones: 60 ohms (Unit is designed for use with ohm phones.
IC-I AND IC-I F GENERAL DESCRIPTION The IC-1 and IC-1 F are single-channel, singleline intercom stations designed for use with dynamic headsets. The IC-1 is a compact, lightweight unit which may be worn
More informationEQ573 Assembly guide. EQ573 Assembly guide Main board 1. Diodes. 2. Resistors (1) 3. Test pins. 4. Ceramic capacitors.
EQ573 Assembly guide Safety warning The kits are main powered and use potentially lethal voltages. Under no circumstance should someone undertake the realisation of a kit unless he has full knowledge about
More informationParts IV-11 DCF melody Date, Weekday, Temperature
Parts IV-11 DCF melody Date, Weekday, Temperature Parts PSU Parts Bag 1a Power Adapter 12 Volt F1 Bridge / NTC 10R black NTC only for Power Adapter 15 Volt R1 4,7M yellow, violet, green R2 1M brown, black,
More informationBuilding the VMW Time Circuitry Meter by Vincent M. Weaver 6 May 2014
Building the VMW Time Circuitry Meter http://www.deater.net/weave/vmwprod/hardware/time_circuit/ by Vincent M. Weaver 6 May 2014 1 Introduction This is a work in progress. I will update it as I complete
More informationGENERAL DESCRIPTION SPECIFICATIONS. output Impedance: Phones: 60 ohms (Designed for use with ohm phones.)
GENERAL DESCRIPTION The IC-S is a single-channel speaker station designed for use with an external microphone. There are four versions of the IC-S; all identified by the same model name, but distinguished
More informationRC Tractor Guy Controller V2.1 Assembly Guide
RC Tractor Guy Controller V. Assembly Guide Features 0 Push button inputs Dual axis thumb sticks with built-in push button Rotary encoders with built-in push button MCU Socket to suit Meduino Mega 560
More information4.0 Blue LED DCF77 Clock documentation
4.0 Blue LED DCF77 Clock documentation 1. LED Clock Main Board PCB mounting: Mount and solder the eight wire bridges. Mount and solder resistors R16, R18, R20, R22. Mount and solder capacitors C1 C3 (pitch
More informationRapid40i PIC Prototyping PCB User Manual
Description This is a PCB designed to facilitate the rapid prototyping of a device based on a 40 pin Microchip PIC microcontroller. To allow users to focus on their application, we take care of key housekeeping
More informationUzebox Kit Assembly Guide
Uzebox Kit Assembly Guide V1.7 Page 1 of 21 Revision History Version Date Author Description 1.0 01-Nov-2012 A.Bourque Initial release 1.1 6-Nov-2012 A.Bourque Minor corrections 1.2 28-Jan-2014 A.Bourque
More informationA Backlighted LCD for your K1
A Backlighted LCD for your K1 (K1BKLTKIT) Tom Hammond - NØSS, July 27, 2006 Rev C Thanks to Wayne Burdick, N6KR for suggesting this implementation of backlighting the K1 display. APPLICABILITY This modification
More informationdual bipolar voltage controlled step sequencer DIY ASSEMBLY MANUAL v1.03
dual bipolar voltage controlled step sequencer DIY ASSEMBLY MANUAL v1.03 Contents Contents... 2 Introduction... 3 Part Sourcing Notes for Non Kit Builders... 3 Eurorack Kit Assembly... 4 Resistors and
More informationAssembly Instructions (8/14/2014) Your kit should contain the following items. If you find a part missing, please contact NeoLoch for a replacement.
NeoLoch NLT-28P-LCD-5S Assembly Instructions (8/14/2014) Your kit should contain the following items. If you find a part missing, please contact NeoLoch for a replacement. Kit contents: 1 Printed circuit
More information4.1 Parts and Components... IV Assembly Tips... IV Assembly Precautions... IV Required Tools, Equipment and Materials..
IV PERSONALITY MODULE ASSEMBLY 4.1 Parts and Components............ IV-1 4.2 Assembly Tips............... IV-1 4.3 Assembly Precautions............ IV-1 4.4 Required Tools, Equipment and Materials.. IV-1
More informationBuffaloLabs WiFi Lantern Assembly guide version 1
BuffaloLabs WiFi Lantern Assembly guide version 1 Needed equipment: Solder iron Solder wire Cutter Wire stripper (optional) Hot glue gun Overview of the components (not including USB cable and box panels)
More informationGotharman s DIY demoon
Gotharman s DIY demoon Assembly Manual Index Introduction 3 Mainboard Connections 4 Control Panel 5 Assembling The Full Kit 6 Assembling demoon From Mainboard Only 16 Mounting DIY demoon In A Box 18 Troubleshooting
More informationConnecting igaging DigiMAG Scales to the Caliper2PC Interface A step by step Guide
What is an igaging DigiMAG Scale? The igaging DigiMAG are digital linear scales that are easily connectable to the Caliper2PC interface. They consist of two parts, the encoder and the readout unit. The
More informationDigital Candle 1.0 Kit
Kit Instruction Manual Eastern Voltage Research, LLC June 2012, Rev 1 1 http://www.easternvoltageresearch.com Introduction to the Kit Thank you for purchasing the Kit. This kit is definitely a favorite
More informationby illumicon APRSTRACKER Pietershoek XA Veldhoven The Netherlands fax
by illumicon www.ezkits.eu APRSTRACKER Pietershoek 3 5503XA Veldhoven The Netherlands fax +31-40-2230020 Contents Introduction...3 Soldering Tips...3 Assembly...4 Schema...5 Connections...6 Adjustments...6
More information