Model Number Structure

Transcription

1 Temperature Meter CSM DS_E_6_1 Highly Visible LCD Display with 2-color (Red and Green) LEDs Wide input range - select from two types of platinum-resistance thermometers and ten types of thermocouples. Front-panel key operation for easy setting. Average processing function suppresses flicker. Temperature input shift and temperature unit selection functions. Easy confirmation of max/min display. Short 80-mm depth (measured from edge of face plate). Finger protective cover (standard equipment) protects against electric shock. Water- and dust-proof NEMA4X (IP66 equivalent) front panel. Recognized conform U.S. and Canadian requirements under the Component Recognition Program of UL. CE marking. Refer Safety Precautions for All Digital Panel Meters. Model Number Structure Model Number Legend -@ Input Type L: Platinum-resistance thermometer or thermocouple 2. Output Type None: No output C: With relay contact output (SPDT) Ordering Information List of Models Rubber Packing Model K32-P1 Note: Rubber packing is provided with the Controller. Accessories (Order Separately) 3. Supply Voltage VAC: VAC 24VAC/VDC: 24 VAC/VDC Input type Supply voltage Output Model Platinum-resistance thermometer or thermocouple VAC None VAC 1 relay contact output (SPDT) -C VAC 24 VAC/VDC None 24VAC/VDC 1 relay contact output (SPDT) -C 24VAC/VDC Name Shape Model Splash-proof Soft Cover K32-49SC Hard Cover K32-49HC 1

2 Specifications Ratings VAC, -C VAC 24VAC/VDC, -C 24VAC/VDC Supply voltage VAC 24 VAC (50/60 Hz), 24 VDC Operating voltage range Power consumption (under maximum load) Insulation resistance Dielectric strength 85% 110% of the rated supply voltage 6 VA max. 4.5 VA max. (24 VAC) 4.5 W max. (24 VDC) 20 MΩ min. (at 500 VDC) between external terminal and case. Insulation provided between inputs, outputs, and power supply. 2,000 VAC for 1 min between external terminal and case. Insulation provided between inputs, outputs, and power supply. Noise immunity ±1,500 V on power supply terminals in normal or common mode. ±1 μs, or 100 ns for square-wave noise with 1 ns. Vibration resistance Vibration: Hz, Acceleration: 50 m/s 2 5 min each in X, Y, and Z directions for 10 sweeps. Shock resistance ±480 V on power supply terminals in normal mode. ±1,500 V in common mode. ±1 μs, or 100 ns for square-wave noise with 1 ns. 150 m/s 2 (100 m/s 2 for relay contact outputs) 3 times each on 3 axes, 6 directions. Ambient temperature Operating: 10 C 55 C (with no condensation or icing) Srage: 25 C 65 C (with no condensation or icing) Ambient humidity Operating: 25% 85% (with no condensation) Approved safety standards UL , conforms EN (Pollution degree 2/overvoltage category II) Conforms VDE0106/P100 (finger protection) EMC (EMI) EN61326+A1 Industry Emission Enclosure: CISPR 11 Group 1 class A Emission AC Mains: CISPR 11 Group 1 class A (EMS) EN61326+A1 Industry Immunity ESD: EN : 4 kv contact discharge 8 kv air discharge Immunity RF-interference: EN : 10 V/m (amplitude-modulated, 80 MHz 1 GHz) Electrical Fast Transient Noise: EN : 2 kv (power line) Immunity Burst Noise: 1 kv line line (I/O signal line) Immunity Surge: EN : 1 kv (power line) 2 kv line ground (power line) Weight Immunity Conducted Disturbance: EN : 3 V ( MHz) Immunity Voltage Dip/Interrupting: EN : 0.5 cycle, 0, 180, 100% (rated voltage) Approx. 200 g 2

3 Characteristics Indication accuracy (at 23±5 C) (See note.) Note: The indication accuracy of the K thermocouple at a temperature of C is ±2 C ±1 digit maximum. The indication accuracy of the T and N thermocouples at a temperature of 100 C or less is ±2 C ±1 digit maximum. The indication accuracy of the U and L thermocouples at any temperature is ±2 C ±1 digit maximum. The indication accuracy of the B thermocouple at a temperature of 400 C or less is unrestricted. The indication accuracy of the R and S thermocouples at a temperature of 200 C or less is ±3 C ±1 digit maximum. Measuring Ranges Platinum-resistance Thermometer Thermocouple Input/Output Ratings Relay Contact Output Thermocouple: (±0.5% of indication or ±1 C, whichever greater) ±1 digit max. Platinum-resistance thermometer: (±0.5% of indication or ±1 C, whichever greater) ±1 digit max. Input Thermocouple: K, J, T, E, L, U, N, R, S, B Platinum-resistance thermometer: JPt100, Pt100 Measurement method Double integral method Sampling period 500 ms Display refresh period Sampling period (sampling times multiplied by number of averaging times if average processing is selected.) Max. displayed digits 4 digits ( ) Display 7-segment digital display, Character height: 14.2 mm Polarity display is displayed aumatically with a negative input signal. Zero display Leading zeros are not displayed. Input shift Input shift equivalent the setting supported for all points within the sensor measurement range. Hold function Max hold (maximum ), Min hold (minimum ) Hysteresis setting Programmable with front-panel key inputs ( ). Other functions Display color change (green (red), green, red (green), red) Average processing (simple average OFF/2/4/8 operations) Setting change lockout Parameter initialization Output Relay contact (SPDT) Delay in comparative outputs 1 s max. Degree of protection Front panel: NEMA4X for indoor use (equivalent IP66) Rear case: IEC standard IP20 Terminals: IEC standard IP00 + finger protection (VDE0106/100) Memory protection Non-volatile memory (EEPROM) (possible rewrite 100,000 times) Input Pt100 JPt100 Range C F Parameter Input K J T E L U N R S B Range C F Parameter Item Resistive load (cosφ = 1) Inductive load (cosφ = 0.4, L/R = 7 ms) Rated load (UL ratings) 5 A at 250 VAC, 5 A at 30 VDC 1.5 A at 250 VAC, 1.5 A at 30 VDC Rated carry current 5 A max. (at COM terminal) Max. contact voltage 400 VAC, 150 VDC Max. contact current 5 A (at COM terminal) Max. switching capacity 2,000 VA, 192 W 375 VA, 30 W Min. permissible load (P level, reference ) 10 ma at 5 VDC Mechanical life 20,000,000 times min. (at a switching frequency of 1,200 time/min) Electrical life 100,000 times min. (at a rated load switching frequency of 10 time/min) (at an ambient temperature of 20 C)

4 Connections Terminal Arrangement Power supply Models with A1 comparative E1 output A2 OUT1 E2 Output VAC type or terminals 24-VAC/VDC type E3 (No polarity for 24-VDC connection.) E4 Input terminals + E5 E6 For thermocouple input A E4 B E5 B E6 For platinumresistance thermometer input A1 - A2 E4 E1 - E6 - E5, E2 - E3 Terminal No. Name Description Operation power Connects the operation power supply. Thermocouple or platinum-resistance thermometer input Outputs Connects the thermocouple or platinum-resistance thermometer input. Outputs the relay outputs. Block Diagram Input Input Key Microcomputer Display EEPROM 5 V 12 V Output circuit X Contact output (See note.) Constant voltage circuit Power supply circuit Note: Relay output models only. 4

5 Operation Main Functions Input Types and Ranges Parameter Setting Input type Meaning in-t 0 Platinum-resistance Pt C F 1 thermometer C F C F 3 JPt C F C F 5 Thermocouple K C F C F 7 J C F C F 9 T C F C F 11 E C F 12 L C F 13 U C F C F 15 N C F 16 R C F 17 S C F 18 B C F Note: The initial is 5: thermocouple K ( C/ F). Temperature Unit Selection Either centigrade ( C) or fahrenheit ( F) can be selected as the temperature unit. Parameter Setting Meaning d-u c Display in C. f Display in F. OUT Types (Comparative Output Models Only) OUT 1 can be set operate in one of the three following modes in accordance with the compared s: Upper limit (High Acting): The output is turned ON when the measurement is greater than its set. Lower limit (Low Acting): The output is turned ON when the measurement is less than its set. Upper and lower limits (Outside Band Acting): An upper limit (H set ) and lower limit (L set ) can be set independently. The output is turned ON when the measurement is greater than the upper-limit set or less than the lower-limit set. Parameter Setting Meaning out 1.t hi Upper limit: Alarm operates at upper limit. lo Lower limit: Alarm operates at lower limit. hi-lo Upper and lower limits: Alarm operates at upper and lower limits. Upper Limit (High Acting) Lower Limit (Low Acting) Upper and Lower Limits (Outside Band Acting) OUT1 Measurement Output ON OFF Hysteresis Measurement OUT1 Output ON OFF Hysteresis OUT1 upper-limit Measurement OUT1 lower-limit ON Output OFF Hysteresis Hysteresis 5

6 Temperature Input Shift Input shift equivalent the setting supported for all points within the sensor measurement range. Parameter ins Temperature Before shift Setting Changing the Display Color The color of the displayed can be set either red or green. For comparative output models, the display color can be set change from green red, or from red green, according the status of the comparison criterion. OUT1 Green Red After shift Temperature input shift Parameter Initialization This function returns all of the parameters their initial s. Parameter Setting Meaning init off --- on Initializes all parameters. Use this reset the after returning it its facry-set condition. Average Processing Input Display Au-return Time This function aumatically returns the display the operation level s current if no keys are pressed for a preset time (called the display au-return time). Move--Protect-Level Time The time required shift the protect level can be set as desired. MAX/MIN Display The maximum and minimum measurement (display) s from the time the power is turned ON until the current time can be sred and displayed. This is useful, for example, when measuring the maximum. Current Average processing stabilizes displayed s minimize flicker by averaging the fluctuating input signals. Average processing can be performed for the measurement s in either of four steps (OFF, 2 times, 4 times, or 8 times). MAX/MIN LEVEL SHIFT UP Max MAX MAX/MIN MAX/MIN MAX/MIN LEVEL SHIFT UP This is useful for ignoring rapid fluctuations, e.g., eliminating spike noise. Hysteresis (Comparative Output Models Only) The hysteresis of comparative outputs can be set prevent chattering in the output when the measurement fluctuates finely near the OUT. Upper limit (high acting) Min MAX/MIN LEVEL SHIFT UP MIN MAX/MIN Set Hysteresis Measurement ON Output OFF 6

7 Nomenclature 2. Operation indicars 3. Level indicar 1 Max Min SV 1. Main indicar MAX/MIN LEVEL SHIFT UP 4. MAX/MIN key 5. Level key 6. Mode key 7. Shift key 8. Up key Name Functions 1. Main indicar Displays current s, parameters, and set s. 2. Operation 1 Lit when output 1 is ON. indica- SV Lit when a set is being displayed or changed. rs Max Lit when the main indicar is showing the MAX. Min Lit when the main indicar is showing the MIN. 3. Level indicar Displays the current level that the is in. (See below for details.) 4. MAX/MIN Key Used display the MAX and MIN s when a measurement is being displayed. 5. Level Key Used change the level. 6. Mode Key Used allow the main indicar indicate parameters sequentially. 7. Shift Key Used enable a set be changed. When changing a set, this key is used move along the digits. 8. Up Key Used change a set. Used set or clear a forced-zero function when a measurement is being displayed. p Not lit a s f Level indicar Level Protect Operation Adjustment Initial setting Advanced-function setting 7

8 Dimensions Finger protective cover (provided) Main indicar character size Panel cut-out 120 min. A B C D E 14.2 mm mm 75 min Mounting Recommended Panel Thickness 1 8 mm. Mount the product horizontally. MAX/MIN LEVEL SHIFT UP The uses M3 terminals. A terminal cover is provided. Application Examples Moniring the temperature of an industrial furnace Sending a temperature alarm for molding equipment Moniring the bearing temperature for a generar mor PID control E5EN Generar mor Industrial furnace Molding Alarm equipment output Alarm output Alarm output Moniring the temperature of an industrial furnace/sintering furnace. Moniring/alarm function for disinfecting equipment. Moniring (failsafe checking) abnormal temperatures in molding equipment. Moniring the liquid temperature for cleaning devices. Moniring temperature rises in electric power generating facilities. Inspecting temperatures in machines and devices. 8

9 Installation 1. Insert the in the panel cut-out hole. 2. For a waterproof installation, insert the rubber gasket on the body of the. Wiring Use the following M3 crimp terminals. 5.8 mm max. 5.8 mm max. Unit Labels (Provided) The unit labels are not attached the. Select the desired labels from the provided sheet. 3. Fit the adapr in the grooves on the left and right sides of the rear case, then push it until it contacts the panel secure the. Note: For scales and gauges, use the unit labels that are specified by the relevant laws or regulations. LCD Angle of View The K3MA is designed provide the best visibility at the angles shown in the following diagram Rubber Packing (Sold Separately) K32-P1 If the rubber packing is lost or damaged, it can be ordered using the following model number: K32-P1. (Depending on the operating environment, deterioration, contraction, or hardening of the rubber packing may occur and so, in order ensure the level of waterproofing specified in NEMA4, periodic replacement is recommended.) Note: Rubber packing is provided with the Controller. Wiring Precautions Use crimp terminals. Tighten the terminal screws a rque of approximately 0.5 N m. To avoid the influence of noise, route signal lines and power lines separately. 9

10 Operating Procedures Operations in Run Mode Checking the Maximum and Minimum Values The maximum and minimum s can be displayed by pressing the MAX/MIN Key while the measurement is being displayed. Measurement MAX/MIN Key MAX MAX/MIN Key MIN MAX/MIN Key The maximum and minimum s can be reset by pressing the MAX/MIN Key for 1 s min. when the maximum or minimum is displayed. Checking and Setting Comparative Set Values (for Models with the Comparative Output Function) Each time the Mode Key is pressed when the measurement, maximum, or minimum is displayed, the comparative s will be displayed in the following order: OUT1 (or OUT1 upper-limit, OUT1 lower-limit ). Adjustment Level Operation Setting Temperature Input Shift Values Temperature Input Shift A shift can be set for a temperature input. Temperature After shift Input shift Before shift Measurement MAX MIN Mode Key OUT1 upperlimit OUT1 Mode Key OUT1 lowerlimit Mode Key Input The set for the temperature input shift is applied the entire measurement range of the temperature sensor. 10

11 Levels Level refers a grouping of parameters. The following table lists the operations that are possible in each of the levels, and the diagram tells how move between levels. There are some parameters that are not displayed for certain models. Level name Function Measurement Protect Setting lockouts. Continue Operation Displaying current s, and setting OUT 1. Continue Adjustment Setting communications writing control. Continue Initial setting Making initial settings of input type, output operating action, and other Spped parameters. Advanced-function setting Setting average processing, display color settings, and other advanced function parameters. Spped Power ON + Time set by user (See note.) Operation level 1 s min. Adjustment level Less than 1 s Flashing sps if key is released. Protect level + 1 s min. 1 s min Indicates change of level. Continue press the key for 2 s min. Initial setting level 1 s min. Password "0169" Advanced-function setting level Note: The move--protect-level time can be set in the advanced-function setting level. 11

12 Parameters Note: 1. Some parameters are not displayed for certain models. 2. The will sp measurement if the level is changed the initial setting level or the advanced-function setting level. 3. If the input range is changed, some parameters are set default s. Therefore, set the input range first. 4. Settings displayed in reversed colors are defaults. Power ON Adjustment level Press Level Key for less than 1 s. Press Level Key for less than 1 s. Operation level Current 0 Temperature input shift For models with the comparative output function OUT1 Set one of these. OUT1 upper-limit OUT1 lower-limit 12

13 Press Level Key for more than 3 s. Press Level Key for more than 1 s. Models with the comparative output function Initial setting level Input type Temperature unit OUT1 type Move advancedfunction setting level To change a setting, press the Shift Key make the change with the Up Key. Press Level Key for less than 1 s. Temperature unit OUT1 type Upper Limit Lower Limit Upper/Lower Limits Password: 0169 Enter password "0169" Models with the comparative output function again, and then Advanced-function setting level Parameter initialization Average processing OUT1 Hysteresis Display color change / / / / Unit: times OUT1 hysteresis Green (red) Green Red (green) Red Display au-return time Unit: s Move-protectlevel time Unit: s Settings displayed in reversed colors are initial settings. 13

14 Press Level Key + Mode Key for more than 1 s. Operation Level Press Level Key + Mode Key for more than preset time. Protect level Operation/adjustment lockouts Setting level lockouts / / / / Setting change lockout / Operation/Adjustment Lockouts Restricts key operations for operation level and adjustment level. Parameter Setting Operation level Moving adjustment level Process display Initial setting is 0. This cannot be displayed on models not equipped with the comparative output function. Setting Level Lockouts Restricts shifting initial setting level or advanced-function setting level. Setting Change Lockout Set display oapt 0 Allowed Allowed Allowed 1 Allowed Allowed Prohibited 2 Allowed Prohibited Prohibited Parameter Setting Shift initial setting level icpt 0 Allowed Allowed Restricts setting changes by key operation. When this lockout is set, it is no longer possible shift a setting change mode. However, all protect level parameters can still be changed. Shift advancedfunction setting level 1 Allowed Prohibited 2 Prohibited Prohibited Parameter Setting Setting change by key operation wtpt off Allowed on Prohibited Initial Settings Press the Level Key level. Select the input type. Power ON for 3 s min. move the initial setting If desired, shift the adjustment level set the temperature input shift. If required, shift the advanced-function setting level set the number of measurements for averaging, hysteresis s, au-zero time, display color change, display au-return time, or move--protect-level time. Press the Level Key operation level. Set the OUT s. for less than 1 s min. return the Measurement starts. 14

15 1 SV MAX/MIN LEVEL SHIFT UP Setting Example Initial Settings The settings for the following example are shown here. Example: Moniring the temperature of an industrial furnace Here, the temperature inside the furnace is be displayed in centigrade ( C). Temperature sensor: E52-PR Thermocouple, Measurement range: 0 1,400 C. 1. Set the input type the thermocouple R input range. Parameter: in-t (input type), Setting : Select centigrade ( C) as the temperature unit. Parameter: d-u (temperature unit), Setting : c If you are using a comparative output model, make the setting as desired. Industrial furnace E52-PR Thermocouple Max Min Troubleshooting -C VAC When an error occurs, error details will be displayed on the main indicar. Confirm the error from the main indicar and take the appropriate countermeasures. Level display Main indicar Error contents Countermeasures Not lit e111 RAM memory error Repair is necessary. Consult your OMRON sales representative. 5 e111 EEPROM memory error When this error is displayed, press the Level Key for 3 seconds, and the settings will be resred the facry settings. If the error cannot be recovered, repair is necessary. Consult your OMRON sales representative. Not lit Flashes s.err Input error Confirm that the temperature sensor is correctly connected, and that there are no broken signal lines the temperature sensor. Input is out of the specified range (control range). Set the within the range immediately. If the condition does not return normal, repair is necessary. Consult your OMRON sales representative. Not lit Flashes 9999 The measurement after temperature input correction exceeds Not lit Flashes The measurement after temperature input correction is lower than The temperature input correction may be inappropriate. Use the adjustment level review the temperature input correction. The temperature input correction may be inappropriate. Use the adjustment level review the temperature input correction. ALL DIMENSIONS SHOWN ARE IN MILLIMETERS. To convert millimeters in inches, multiply by To convert grams in ounces, multiply by In the interest of product improvement, specifications are subject change without notice. 15

16 Read and Understand This Catalog Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or comments. Warranty and Limitations of Liability WARRANTY OMRON's exclusive warranty is that the products are free from defects in materials and workmanship for a period of one year (or other period if specified) from date of sale by OMRON. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING NON-INFRINGEMENT, MERCHANTABILITY, OR FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS. ANY BUYER OR USER ACKNOWLEDGES THAT THE BUYER OR USER ALONE HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. OMRON DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. LIMITATIONS OF LIABILITY OMRON SHALL NOT BE RESPONSIBLE FOR SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED ON CONTRACT, WARRANTY, NEGLIGENCE, OR STRICT LIABILITY. In no event shall the responsibility of OMRON for any act exceed the individual price of the product on which liability is asserted. IN NO EVENT SHALL OMRON BE RESPONSIBLE FOR WARRANTY, REPAIR, OR OTHER CLAIMS REGARDING THE PRODUCTS UNLESS OMRON'S ANALYSIS CONFIRMS THAT THE PRODUCTS WERE PROPERLY HANDLED, STORED, INSTALLED, AND MAINTAINED AND NOT SUBJECT TO CONTAMINATION, ABUSE, MISUSE, OR INAPPROPRIATE MODIFICATION OR REPAIR. Application Considerations SUITABILITY FOR USE OMRON shall not be responsible for conformity with any standards, codes, or regulations that apply the combination of products in the cusmer's application or use of the products. At the cusmer's request, OMRON will provide applicable third party certification documents identifying ratings and limitations of use that apply the products. This information by itself is not sufficient for a complete determination of the suitability of the products in combination with the end product, machine, system, or other application or use. The following are some examples of applications for which particular attention must be given. This is not intended be an exhaustive list of all possible uses of the products, nor is it intended imply that the uses listed may be suitable for the products: Outdoor use, uses involving potential chemical contamination or electrical interference, or conditions or uses not described in this catalog. Nuclear energy control systems, combustion systems, railroad systems, aviation systems, medical equipment, amusement machines, vehicles, safety equipment, and installations subject separate industry or government regulations. Systems, machines, and equipment that could present a risk life or property. Please know and observe all prohibitions of use applicable the products. NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCTS ARE PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. PROGRAMMABLE PRODUCTS OMRON shall not be responsible for the user's programming of a programmable product, or any consequence thereof. Disclaimers CHANGE IN SPECIFICATIONS Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice change model numbers when published ratings or features are changed, or when significant construction changes are made. However, some specifications of the products may be changed without any notice. When in doubt, special model numbers may be assigned fix or establish key specifications for your application on your request. Please consult with your OMRON representative at any time confirm actual specifications of purchased products. DIMENSIONS AND WEIGHTS Dimensions and weights are nominal and are not be used for manufacturing purposes, even when lerances are shown. PERFORMANCE DATA Performance data given in this catalog is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of OMRON s test conditions, and the users must correlate it actual application requirements. Actual performance is subject the OMRON Warranty and Limitations of Liability. ERRORS AND OMISSIONS The information in this document has been carefully checked and is believed be accurate; however, no responsibility is assumed for clerical, typographical, or proofreading errors, or omissions. OMRON Corporation Industrial Aumation Company In the interest of product improvement, specifications are subject change without notice. (c)copyright OMRON Corporation 2010 All Right Reserved.