NXAMP4x4 Powered TDController

Transcription

1 NXAMP4x4 Powered TDController NEW DUAL-VOLTAGE VERSION The complete integration of power and control NXAMP 4X4 is an ultra-flexible, true four-channel digital processing and amplification system delivering an integrated solution for any NEXO speaker configuration. NXAMP technology is far more sophisticated than simply a bundled power amplifier and loudspeaker controller. The application of advanced DSP allows multiple digital sense lines to protect simultaneously the amplifier and the connected speakers. The NXAMP 4x4 uses a unique dual mains cord, feeding the power supplies with almost twice the power of that in a conventional amplifier design, while being extremely easy to connect to any single or multi-phase mains supply. To absorb this enormous current, the NXAMP4x4 uses four independent, high-power, full resonant power supplies working in opposite phase to cancel noise and lower EMC. Yamaha EEEngine technology delivers maximum efficiency in drive performance and power, with the sonic purity of conventional class AB amplifiers, and heat dissipation equivalent to class D. New Features New dual-voltage version Optional Dante and EtherSound network cards New Firmware LOAD 3.0 Set up selection per channel Linear phase on all set-ups All systems compatible 20Hz-20kHz Dual-core DSPs take care of amplifier protection and optimisation, while raising the processing standard of NEXO proprietary loudspeaker management technology to higher levels of sonic performance and reliability. Additional features include full computerless front-panel operation and on-the-fly independent loudspeaker per output selection or load monitoring through GPIO or Ethersound. 12

2 Dimensions Specifications POWER SPECIFICATIONS FOR NXAMP4x4 Number of channels 4x amplifiers channels, 2 by 2 bridgeable Max. output voltage (no load) 4x 200 Volts Max. output power (4 channels mode /8 Ohms load per channel) 4x 1900 Watts Max. output power (4 channels mode /4 Ohms load per channel) 4x 3300 Watts Max. output power (4 channels mode /2 Ohms load per channel) 4x 4000 Watts Max. output power (2 channels mode /8 Ohms load per channel) 2x 6800 Watts Max. output power (2 channels mode /4 Ohms load per channel) 2x 8000 Watts Power consumption (Standby) 20 Watts Power consumption (Idle) 120 Watts INPUT TO POWER OUT SPECIFICATIONS Frequency response +0.5 db from 10 Hz to 20 KHz Input impedance / Max. level 20 K / +28 dbu Dynamic range / TDH + N 105 db unweighted / Typical 0.1% on a flat setup Latency 500 us on a flat setup A to D Converters Audio and current/voltage sense lines : KHz Processing Two dual-core 24 bits fixed point DSP with 56 bits accumulator BACK PANEL FEATURES Analog audio inputs Power outputs RS232 port GPIO port Expansion slot Mains sockets 4x balanced analogue inputs on XLR3 with a second XLR3 for link 4x Neutrik Speakon NL-4 outputs 1x DB-9 connector for firmware upgrade and accessories connection 1x DB-25 connector with 5x Global Purpose Inputs and 8x Global Purpose Outputs For networking audio cards, 4x digital audio inputs and remote control 2x Neutrik Powercon NAC3 (2x 16 A) or NAC3-HC (2x 32 A) depending on model USER INTERFACE AND CONTROLS Front panel buttons and knobs Display Global status display Speakers/Amp status display DIMENSIONS AND CERTIFICATIONS Dimensions Weight Electrical Safety Certification EMC Certification Green status On/Off Mains switch, Select Wheel, 2x Menus buttons, 4x Select and 4x Mute buttons 40 characters by 2 lines LCD display with LED backlight. Power, Standby and Amp Protect LEDs. Per channel, output current sensing, speaker protection and channel soft clip. 4U 19" Rack mm (18") Depth 24.5 Kg (49 lbs) net cetlus, CB (CE) CE, FCC Compliant with ROHS directive NXAMP4x4 (for 110/120 V mains) NX.AMP4x4U (1 x NXAMP4x4U, 1 x Quick Start, 2 x US power cords) NXAMP4x4 (for 220/240 V mains) NX.AMP4x4C (1 x NXAMP4x4C, 1 x Quick Start, 2 x CH power cords) NXAMP4x4 (dual voltage mains) NX.AMP4x4W (1 x NXAMP4x4W, 1 x Quick Start) NXAMP4x4 handles kit NX.AMP4x4-HAND (2 x NXAMP4x4 handles w screws) 13

3 DMU Digital Meters Unit Data Sheet Digital Meters Unit for NXAMP Powered TDcontrollers The ultimate tool for easy monitoring of any activitity on the NXAMP powered TDcontrollers inputs. DMU mains features Intelligent input patch panel offering digital communication with NXAMPs. Provide input level meters on all analog and network inputs. Fully passive design on the audio and network paths. Powered through the host NXAMP, no need for mains supply. The DMU is an unique tool that will perfectly fit your NXAMPs when used on the road. It offers all the necessary tools to ensure easy patching of the NXAMP inputs. Traditionnal patch bay... In an elegant but robust 1U low depth enclosure, the DMU offers to most demanding users an immediate overview of all inputs connected to the NXAMP powered TDcontroller. On the left part of the unit, four XLR inputs (with output links) will act like a traditionnal patch bay, outputing the analog signals on four XLR on the back panel, to fit any cable lenght between the DMU and the NXAMP. On the right part of the unit, three Ethercon connectors does the same but with audio and/or remote control networks.... With unique functionnality On each audio input, analog on XLR or digital on Ethercon, the DMU offers a highly readable, eight level vue-meter, plus two status leds for each network inputs. Nothing to configure, these vue-meters are automatically driven (and powered) from the GPIO port of the host NXAMP. Matched impedance routing Unlike entry level input patch bay, using only wires to connect front pannel to back pannel plugs, the DMU uses a carrefuly routed multi-layer PCB, with shielded low impedance design for analog audio and matched impedance design for the high speed network inputs. Part of the NXAMP Universal Rack Together with the DPU (Digital Patching Unit) and the NXAMP4x4, the DMU is part of the NXAMP Universal Rack, the interchangeable standard of power amplifiers for Nexo systems. 50 Analog meters takes care of the variable input gain of the powered TDcontroller, whereas only patched digital inputs among the one availables on an audio network will be displayed

4 DMU Digital Meters Unit Data Sheet METERS FEATURES Integrated vue-meters Network activity 8 channels of 8 levels vue-meters, one per input (4 x Analog and 4 x Network). 2 Leds per network input. FRONT PANEL FEATURES Analog audio connectors 4 x Neutrik XLR-3 with parallel output link on XLR-3, named from A to D. Network connectors 3 x Neutrik Ethercon connectors, named from 1 to 3. NEXO is one of the world's leading sound reinforcement loudspeaker manufacturers. Founded in 1979, the company is dedicated to crafting practical solutions with solid engineering. Each new design begins with a proprietary sophisticated computer simulation process that allows every parameter to be extensively modeled and simulated, leading to breakthrough cost and performaance gains. NEXO's comprehensive product line includes loudspeakers, analogue and digital control electronics and amplification; all designed to deliver consistent sound quality and long term reliability for a broad range of applications. BACK PANEL FEATURES Analog audio connectors 4 x Neutrik XLR-3 passive connection to front panel XLR. Network connectors 3 x RJ45 connectors, routed to front panel through matched impedance pairs. GPIO connector DB-25 for digital communication and power from host NXAMP. DISPLAYED INFORMATION When muted Connected speaker name, speaker pin-out, connected NXAMP inputs names. When unmuted Connected speaker name, output meter. SPECIFICATIONS Power supply From GPIO port, 5 Volts DC, 1Watts. Dimensions 1U 19" Rack - 50 mm (2") Depth. Weight 1.2 Kg (2.6 lbs) net. Electrical Safety Certification cetlus, CB (CE) EMC Certification CE, FCC Green status Compliant with ROHS and REACH directive. Digital Meters Unit for NXAMP NX.DMU (1 x DMU, 1 x Quick Start Guide) Cable Kit for DMU NX.DMU.CK (4 x Neutrik XLR to XLR cords, 3 x RJ45 link (R,G,B), and 1 x DB-25 link) NEXO S.A. Parc d Activiteé du Prée de la Dame Jeanne B.P PLAILLY Tel: +33 (0) Fax: +33 (0) NEXO LatAM C.C. No 33. Suc 49 Caballito (1449) Buenos Aires Argentina Tel: Fax: NEXO Asia GPO Box 806 Hong Kong SAR China Tel: Fax: LIMITED WARRANTY NEXO loudspeakers and electronics are covered against defects in workmanship or materials for a period of two (2) years from the original date of purchase. At the option of NEXO the defective item will be repaired/replaced with no charge for materials/labour. The item is to be adequately packaged and dispatched, pre-paid, to a NEXO authorised distributor/service centre. Unauthorised repair shall void the warranty. The NEXO warranty does not cover cosmetics or fnish and does not apply to any items which in NEXO s opinion have failed due to used abuse, accidents, modifcations or any type of misuse.all images and text herein are the property of NEXO SA, and deemed accurate, although specifcations are subject to change without notice.

5 DPU Digital Patching Unit Data Sheet Digital Patching Unit for NXAMP Powered TDcontrollers The ultimate tool for easy connection between the NXAMP powered TDcontrollers and any Nexo speaker in live environment. DPU mains features Intelligent output patch panel offering digital communication with NXAMPs. Provide automatic output speakons wiring regarding the configuration of the NXAMP. Four individual LCD for easy labeling of the outputs speakons. Fully redundant design for maximum safety, including dual power socket and dual universal power supplies. Plug and play operation, totally driven by the host NXAMP. The DPU is an unique tool that will perfectly fit your NXAMPs when used on the road. It offers all the necessary tools to ensure easy patching of the NXAMP power outputs. World first intelligent output patch Forget about the classical static output patch panel full of sticky tape and unreadable inscriptions. The DPU communicates directly with the NXAMP and knows which loudspeaker setup is currently running. It can then automatically route the amplifier s power outputs to the correct output speakon on its front panel, whatever Nexo's speaker is connected, in bridge mode or not. Ultimately, it offers the possibility to link two NXAMP together on the same output, for systems where more than one amplifier is needed. Fully redundant design The DPU is powered through a dual fully certified medical grade power supply system. Any of the two lockable power cords can be unplugged anytime without any drop on the audio signal. The heavy duty ultra low impedance switching matrix used for audio routing is also implemented using a redundant design, ensuring maximum security. Usefull display The DPU provides also crutial information when connecting your Nexo speakers to the NXAMP. When the NXAMP is muted, the four individual LCD display for each output the name of the speaker, its pin-out and the NXAMP inputs in use. When unmuted, the LCD turns into four easy readeable output meters. Part of the NXAMP Universal Rack Together with the DMU (Digital Meters Unit) and the NXAMP4x4, the DPU is part of the NXAMP Universal Rack, the interchangeable standard of power amplifiers for Nexo systems. 248 Zero configuration Using the DPU is extremely easy ; not only there is nothing to set up, as all routing parameters are automatically configured, but it tests also that all connections to NXAMP are correct

6 DPU Digital Patching Unit Data Sheet ROUTING FEATURES Routing Matrix Route any of the four input channels to one or several Speakon pins pairs on the front. FRONT PANEL FEATURES Power outputs LCD Displays 4 Neutrik Speakon-4 and 2 Neutrik Speakon-8. 4 LCD displays, 2 x 8 characters. NEXO is one of the world's leading sound reinforcement loudspeaker manufacturers. Founded in 1979, the company is dedicated to crafting practical solutions with solid engineering. Each new design begins with a proprietary sophisticated computer simulation process that allows every parameter to be extensively modeled and simulated, leading to breakthrough cost and performaance gains. NEXO's comprehensive product line includes loudspeakers, analogue and digital control electronics and amplification; all designed to deliver consistent sound quality and long term reliability for a broad range of applications. BACK PANEL FEATURES NXAMP power inputs 2 Neutrik Speakon-4 for connecting the NXAMP Powered TDcontroller. NXAMP interface RS232 interface for communication with the NXAMP Powered TDcontroller. Mains inputs 2 IEC connectors with security latch. DISPLAYED INFORMATION When muted Connected speaker name, speaker pin-out, connected NXAMP inputs names. When unmuted Connected speaker name, output meter. SPECIFICATIONS Power supply Fully redundant, dual universal 100 ~ 240 Volts, 50 or 60 Hz, 25 Watts Dimensions 1U 19" Rack mm (10") Depth Weight 4.7 Kg (10.4 lbs) net Electrical Safety Certification cetlus, CB (CE) EMC Certification CE, FCC Green status Compliant with ROHS and REACH directive Digital Patching Unit for NXAMP NX.DPU (1 x DPU, 1 x Quick Start Guide) Cable Kit for DPU, 100 ~120 Volts NX.DPU.CK1 (2 x US lockable power cord, 1 x RS232 link, 2 x Speakon link 4x4 mm²) Cable Kit for DPU, 220 ~240 Volts NX.DPU.CK2 (2 x EU lockable power cord, 1 x RS232 link, 2 x Speakon link 4x4 mm²) NEXO S.A. Parc d Activiteé du Prée de la Dame Jeanne B.P PLAILLY Tel: +33 (0) Fax: +33 (0) NEXO LatAM C.C. No 33. Suc 49 Caballito (1449) Buenos Aires Argentina Tel: Fax: NEXO Asia GPO Box 806 Hong Kong SAR China Tel: Fax: LIMITED WARRANTY NEXO loudspeakers and electronics are covered against defects in workmanship or materials for a period of two (2) years from the original date of purchase. At the option of NEXO the defective item will be repaired/replaced with no charge for materials/labour. The item is to be adequately packaged and dispatched, pre-paid, to a NEXO authorised distributor/service centre. Unauthorised repair shall void the warranty. The NEXO warranty does not cover cosmetics or fnish and does not apply to any items which in NEXO s opinion have failed due to used abuse, accidents, modifcations or any type of misuse.all images and text herein are the property of NEXO SA, and deemed accurate, although specifcations are subject to change without notice.

7 NXES104 EtherSound TM Network Card Key Features Extracts 4 audio streams (24 bits / 48 KHz) among the 2 x 64 channels of a ES100 Ethersound TM stream. IN and OUT port for simple daisy chain without any need for an external switch. 3rd Ethernet port for remote control of the whole network from any NXES104 card and ASIO streaming. Specifications NXES104 NXDT104 NXDT104 Dante TM Network Card Key Features Receives 4 audio streams (24 bits / 48 KHz) in Dante TM format. Dual port for redundancy and 3rd port for additional remote control. Direct connection to PC using the ASIO format. NETWORK FORMAT Compatible networks Ethersound networks Dante networks Network type Ethernet 100 Mb TCP/IP over Ethernet, 100 Mb or 1 Gb Device addressing Automatic, based on Mac address Automatic, based on IP address with Zeroconf AUDIO FORMAT Number of channels 4 channels from network to NXAMP 4 channels from network to NXAMP Resolution / Sample Rate 24 bits / 48 KHz 24 bits / 48 KHz Latency 0.10 ms 0.15 ms to 5.0 ms FRONT PANEL FEATURES Network inputs 2 shielded Neutrik Ethercon 2 shielded Neutrik Ethercon Additional port RJ45 for additional remote control RJ45 for additional remote control LEDs on network ports Tx and Rx on each port Link/Act and Speed on each port LEDs on additional port Link and activity Link and activity GENERAL SPECIFICATIONS Power supply Volts, 5 W from NEXO slot Volts, 8 W from NEXO slot Dimensions (W x D x H) 120 x 160 x 40 mm (NXAMP slot) 120 x 160 x 40 mm (NXAMP slot) Weight 160 g 200 g EMC certification CE, FCC, ICES CE, FCC, ICES Green Status ROHS and REACH ROHS and REACH Network card ordering NX.ES104 NX.DT104