Variable Frequency Drives

Transcription

1 Table of Contents Variable Frequency Drives PRODUCT PRODUCT CODE RESOURCE DOCUMENTS PAGE # Introduction C-3 NEW! BT300 HVAC Drives BT C-5 NEW! BT300 HVAC Drives with Bypass Options BT300 C-15 Legacy SED2 SED C-19 Legacy SED2 with Bypass Options SED , C-23 Legacy SED2 SED C-29 NEMA Type 3R & Type 3R Harsh Environment Bypass Accessories & Service Kits C-35 C-1

2 C-2

3 Introduction C-3 Siemens, a global leader in drives technology, is raising the bar with new BT300 Variable frequency Drives that are designed specifically for the demands of today s HVAC systems. Increased focus on energy efficiency of variable flow systems has increased the need for easy-to-use and highly reliable variable frequency drives that reduce the cost of installation and maintenance while maximizing energy savings. Siemens Industry s BT300 HVAC drives are designed to meet the demands of today s HVAC systems. An increased focus on energy efficiency of variable flow systems has increased the need for easy-to-use and highly reliable variable frequency drives that reduce the cost of installation and maintenance while maximizing energy savings. While constantly expected to do more with less, managing energy consumption and optimizing occupant comfort remains of utmost importance to facility managers. They also require products that will integrate seamlessly into existing equipment and building management systems. The highly efficient BT300 delivers all this and more. The BT300 comes standard with unique and industry-leading features: View/Monitor nine parameters at one time user selectable, users determine the parameters for their applications Thin Film Capacitors eliminate the need to condition or reform the capacitors before applying power Smallest Type 12 footprint on the market lower shipping cost and easy installation Motor Switch Ride Through during maintenance the motor maintenance switch can be opened and closed without stopping or tripping the drive

4 C-4 We re happy to assist you Our customer support teams are accessible and happy to assist you with ordering, fulfillment, and shipping questions. Call a representative at from 7 am to 5:30 pm (CST) Monday through Friday. Contact Customer Support or your Account Executive with any questions. We appreciate your business and look forward to helping you!

5 BT300 BT300 Variable Frequency Drives Energy & Atmosphere Important Note: VFD products are only available through authorized distribution channels. To locate an authorized distributor, please contact a Siemens Building Technologies representative at: BT300 without and with Integral Disconnect. Description Siemens Industry s BT300 HVAC drives are designed to meet the demands of today s HVAC systems. An increased focus on energy efficient variable flow systems has increased the need for easy-to-use and highly reliable variable frequency drives that reduce the cost of installation and maintenance while maximizing energy savings. HVAC demands are unique to other drive applications. Features Motor Switch Ride Through during maintenance the motor maintenance switch can be opened and closed without stopping or tripping the drive Thin Film Capacitors eliminate the need to condition or reform the capacitors before applying power Intuitive graphical keypad with multilingual display Monitor nine user-defined values at one time Built-in wizards for faster start-up and easy setup of advanced functions Built-in plain text help and maintenance manual shows possible causes and suggested remedies Real time clock allows up to five calendar-based schedules and three timer inputs Ready to communicate to a Building Management System, embedded RS485 and Ethernet HVAC protocols: BACnet IP, Modbus TCP, Modbus RTU, BACnet MSTP, Metasys N2, APOGEE FLN Two built-in PID controllers enable fast and accurate process control Integrated harmonic filters on the DC link reduce noise and interference and eliminate the need for additional filters and reactors Built in fire mode controller Energy Savings with > 97.5% efficiency Optimized cooling fan runs only when needed Belt failure detection with or without an external sensor Accepts a wide variety of digital and analog I/O types, including direct Ni 1000 RTD sensor level inputs One common interface throughout all power ranges Two form C relays RoHS Compliant Smallest Type 12 footprint on the market lower shipping cost and easy installation Options LON Interface Flange Mounting Kits for Frame Sizes 4-7 Varnished I/O Option Boards Door Mounting Kits PC Cable for NET Tool, USB to RS-485, cable length 9.8 ft. (3 m) Real Time Clock Battery Package SED2 to BT300 Migration Kits C-5

6 BT300 Specifications C-6 Input Voltage and Power Ranges (3-phase) 208V - 240V, +/-10%...1 to 125 HP (0.75 to 90 kw) 380V - 480V, +/-10% to 250 HP (1.1 to 160 kw) Input Frequency to 66 Hz Output Frequency... 0 to 320 Hz Frequency Resolution Hz Power Factor at Nominal Load Efficiency... >97.5% Overload Capacity x Nominal Rated Output Current 110% for 1 Minute/10 Minutes Peak Overload Capacity...200% for 2 Seconds Every 20 Seconds Switching Frequency to 10kHz; Automatic Switching Frequency Derating in Case of Overheating Short Circuit Withstand Rating...100,000 AIC Frequency Reference Analog Input Hz Resolution 0.1% (10-bit) Field Weakening Point... 8 to 320 Hz Acceleration/Deceleration Time to 3000 sec Ambient Operating Temperature º F (-10º C) no Frost to 104º F (40º C) Without De-rating and 131º F (55º C) With De-rating Storage Temperature...-40º F (-40º C) to 158º F (70º C) Relative Humidity...0 to 95% RH, Non-condensing, Non-corrosive Air Quality... IEC Chemical Vapors...IEC , Unit in Operation, Class 3C3 Mechanical Particles...IEC , Unit in Operation, Class 3S2 Altitude...100% Load Capacity (no De-rating) up to 3,280 ft (1,000 m) 1% De-rating for Each 328 ft (100 m) Above 328 ft (1,000 m) Maximum Altitude 14,763 ft (4,500 m) Vibration...IEC and IEC Shock...IEC and IEC Enclosures... UL Type 1, UL Type 12 EMC Immunity...Fulfills IEC , First and Second Environment EMC Emissions...EN C2 Average Noise level (Cooling Fan) Sound Level in db(a)...fs4-65; FS5-61; FS6 and FS7: 68 FR8: 77; FR9: 78 Agency Approvals...UL 508C; CE, UL, cul Analog Inputs... 2 Voltage or Current (0-10Vdc, 0/4 to 20 ma) Analog Output...1 Selectable Voltage or Current Digital Inputs... 6 Programmable and Isolated Relay Outputs...2 Form C; 1 Normally Open Auxiliary Input Voltage...24 Vdc +/-10% 250 ma Max. Auxiliary Input Voltage...24 Vdc +/-10% 250 ma Max., Total of Both Outputs Control Method...Linear, Parabolic and Programmable V/f; Flux Current Control Low-Power Mode PWM Frequency... 2k Hz to 16k Hz (Adjustable in 2k Hz Increments) Fixed Frequencies...15 Programmable Skip Frequency Bands...3 Programmable Embedded Resident Protocols...RS485 and Ethernet P1, BACnet MS/TP, BACnet IP, Modbus RTU, Modbus TCP, Metasys N2, APOGEE FLN Protection Features...Under-voltage and Over-voltage Trip Limit, Ground Fault, Mains Supervision, Motor Phase Supervision, Over-current, Unit Over-temperature, Motor Overload, Motor Stall, Motor Underload, Short Circuit of +24V and +10V Reference Voltages Accessories & Service Kits C-35

7 BT300 Product Ordering Your Product Number Example Product Number B T X X Example Product Number B T D L Model BT300 VFD only HP 1, 1.5, 2, 3, 5, 7.5, 10, 15 20, 25, 30, 40, 50, 60, , 125, 150, 200, 250 X No Fract HP, 5 1/2 HP Voltage to to 480 NEMA 01 UL Type 1 12 UL Type 12 Type X Drive Only D Disconnect Box ONLY WITH TYPE 12 Options L LON Card Installed C-7 Example Shown: BT X2-01X = 1 HP, 208V Drive in Type 1 enclosure. BT DL = 1.5 HP, 480V Drive in Type 12 enclosure with an integral disconnect switch and LON card.

8 BT300 Output Ratings C-8 Voltage (±10%) 208V (3-Phase) 230V (3-Phase) 380V to 480V (3-Phase) Product Number Output Rating Rated UL Type 12 with Continuous UL Type 1 UL Type 12 HP kw Drive Disconnect Current BT X2-01X BT X2-12X BT X2-12D FS4 BT X BT X BT D FS4 BT X2-01X BT X2-12X BT X2-12D FS4 BT X2-01X BT X2-12X BT X2-12D FS4 BT X2-01X BT X2-12X BT X2-12D FS5 BT X BT X BT D FS5 BT X2-01X BT X2-12X BT X2-12D FS5 BT X2-01X BT X2-12X BT X2-12D FS6 BT X2-01X BT X2-12X BT X2-12D FS6 BT X2-01X BT X2-12X BT X2-12D FS7 BT X2-01X BT X2-12X BT X2-12D FS7 BT X2-01X BT X2-12X BT X2-12D FS7 BT X2-01X BT X2-12X FS8 BT X2-01X BT X2-12X FS8 BT X2-01X BT X2-12X FS8 BT X2-01X BT X2-12X FS9 BT X2-01X BT X2-12X FS9 BT X BT X BT D FS4 BT X4-01X BT X4-12X BT X4-12D FS4 BT X4-01X BT X4-12X BT X4-12D FS4 BT X4-01X BT X4-12X BT X4-12D FS4 BT X BT X BT D FS4 BT X4-01X BT X4-12X BT X4-12D FS5 BT X4-01X BT X4-12X BT X4-12D FS5 BT X4-01X BT X4-12X BT X4-12D FS5 BT X4-01X BT X4-12X BT X4-12D FS6 BT X4-01X BT X4-12X BT X4-12D FS6 BT X4-01X BT X4-12X BT X4-12D FS6 BT X4-01X BT X4-12X BT X4-12D FS7 BT X4-01X BT X4-12X BT X4-12D FS7 BT X4-01X BT X4-12X BT X4-12D FS7 BT X4-01X BT X4-12X FS8 BT X4-01X BT X4-12X FS8 BT X4-01X BT X4-12X FS8 BT X4-01X BT X4-12X FS9 Frame Size BT X4-01X BT X4-12X FS9

9 BT300 Type 1 and 12 Frame Sizes and Power Range Voltage KW HP V Frame Size NA 480V N/A BT300 Dimensions and Weights Frame Size Height in. (mm) Width in. (mm Depth in. (mm (without Disconnect) Depth in. (mm (with Disconnect) Weight lb. (kg) FS (328) 5.0 (128) 7.5 (190) 10.6 (270) 13.0 (6) FS (419) 5.7 (144) 8.4 (214) 11.6 (294) 22.0 (10) FS (557) 7.7 (195) 9.0 (229) 11.9 (302) 44.0 (20) FS (660) 9.3 (237) 10.2 (259) 13.1 (332) 83.0 (37.5) FS (966) 11.4 (290) 13.5 (343) N/A (66) FS (1150) 18.9 (480) 14.4 (365) N/A (108) C-9

10 BT300 Dimensions FS4, Wall-Mount Type 1/IP21 Ø7 (.27) Ø13 (.51) 128(5.03) 100(3.93) 190(7.48) Ø25 (.98) 313 (12.32) 151 (5.94) 112 (4.40) 328 (12.91) Type 12 /IP54 Ø25 (.98) C (4.40) 147 (5.78) mm (in.) 100(3.93) BT9080 FS5, Wall-Mount

11 BT300 Dimensions FS6, Wall-Mount Ø9 (.35) 195 (7.67) 148 (5.82) Ø 15,5(.61) 229(9.01) Ø33 (1.29) Ø40 (1.57) Ø40 (1.57) 43,7 (1.72) 557 (21.92) 148 (5.82) 541 (21.29) 151 (5.94) Type 1/IP21 Ø25 (.98) Ø25 (.98) 148 (5.82) 42 (1.65) 151 (5.94) C-11 mm (in) Ø9 (.35) 259 (10.19) Ø20 (.78) 148 (5.82) 660 (25.98) FS7, Wall-Mount 237 (9.33) 190 (7.48) Ø9 (.35) Ø16 (.62) 645 (25.39) Ø51 (2) Type 12 /IP54 Type 1 / IP21 Type 12 / IP54 BT (6.29) 211 (8.30) Ø25 (.98) Ø50 (1.96) 160 (6.29) 217 (8.54) 9083bt mm (in)

12 BT300 Dimensions FS8, Wall-Mount C-12

13 BT300 Dimensions FS9, Wall-Mount C-13

14 C-14 Online 24/7 ordering convenience Use this Master HVAC Catalog and Siemens online ordering to maximize ordering efficiency. Go online to: Place orders Browse this catalog online Check product availability and pricing Specify FREE valve tagging Download invoices Track shipments Print out product information for submittals Link to technical documentation Download installation instructions Create a reusable template order form for frequently ordered parts See how easy it is to save time and money. Register today at:

15 BT300 BT300 with Bypass Options Energy & Atmosphere Important Note: VFD products are only available through authorized distribution channels. To locate an authorized distributor, please contact a Siemens Building Technologies representative at: BT300 with Bypass Options. Description The BT300 was designed from the onset with reliability in mind. The BT300 is the first VFD in today s market which has utilized ALT testing from product design to production deployment. However in today s market, some customers want additional assurance their equipment will run regardless of the situation. To accommodate these situations, Siemens has developed a companion product for the BT300, the BT300 with Bypass Options. As the word indicates, a bypass is defined in an engineering spec as a means of taking the drive out of the electrical power loop while keeping the HVAC system up and running. BT300 is available with two types of bypass options. The BT300 with Conventional bypass is designed with 2 contactors and a service switch or the traditional 3-contactor configuration to bypass the drive, and incorporates selector switches and indicator lights to accomplish its primary functions. The second option, an Electronic bypass utilizes internal control boards that act as the brains and eliminates the control wiring, relay logic, terminal blocks and replaces them with advanced built-in features accessible from an electronic keypad. Features Contactors electronically interlocked Advanced diagnostic board built into the bypass for determining status of M1 and M2 contactors Overload Customer supplied start/stop Status of Essential Services Step-down transformer with fused primary and thermal fused secondary circuit Fused disconnect or circuit breaker Option 100,000 AIC short circuit rating Customer Supplied Terminal strip Conventional Bypass Control: Drive test switch Drive-Off-Bypass selector Bypass Light Fused disconnect or circuit breaker Optional 2-contactor with service switch or 3-contactor design (input, output and bypass) Electronic Bypass Control Auto Bypass Option to install 8 separate safety circuits Fieldbus in Bypass Essential Service Mode (Fire mode) Damper Interlock Remote start via network C-15

16 BT300 with Bypass Options Product Ordering C-16 Your Product Number Example Product Number B T E X 4 - B L Model(s) HP BTC BTE 1, 1.5, 2, 3, 5, 7.5,10,15 20, 25, 30, 40, 50, 60, , 125, 150, 200, 250 X=no fract HP 5= 1/2 hp Voltage Disconnect Conventional Electronic to to 480 F B Enclosure Contactor Options Fused Disconnect Circuit Breaker 01 Enclosure Type contactors (input/output and bypass contactors) (Conventional option only) 2 2 contactors bypass with service switch L Lon Card Installed Example shown: BTE -125X4 -B012L BT300 Electronic Bypass, 480 volt, 125hp, Type 1, circuit breaker and 2 Contactor bypass with a service switch and LonWorks card installed in drive BT300 Bypass Options Frame Sizes and Power Ranges Voltage KW HP V Frame Size NA 480V N/A Type 1 Bypass Approximate Weights Frame Size and 9 Weight lbs. (kg) 50 (23) 69 (31) 112 (51) 187 (85) 1000 (454)

17 BT300 Bypass Options Dimensions Frame Size 4.38 MOUNTING HOLES TYPICAL (4) PLACES /2" CONDUIT HOLE WITH 3/4" KNOCKOUT RING TYPICAL (5) PLACES Frame Size 6.44 MOUNTING HOLES TYPICAL (4) PLACES C Frame Size 5.38 MOUNTING HOLES TYPICAL (4) PLACES 1/2" CONDUIT HOLE WITH 3/4" KNOCKOUT RING TYPICAL (3) PLACES /2" CONDUIT HOLE WITH 3/4" KNOCKOUT RING TYPICAL (3) PLACES 3/4" CONDUIT HOLE WITH 1" KNOCKOUT RING TYPICAL (2) PLACES 1-1/4" CONDUIT HOLE WITH 1-1/2" KNOCKOUT RING TYPICAL (2) PLACES

18 BT300 Bypass Options Dimensions Frame Size 7 Frame Size 8 & 9.50 MOUNTING HOLES TYPICAL (4) PLACES TOP ENTRY, BLANK CONDUIT PLATES TYPICAL (4) PLACES C /2" CONDUIT HOLE WITH 3/4" KNOCKOUT RING TYPICAL (3) PLACES 2" CONDUIT HOLE WITH 2-1/2" KNOCKOUT RING TYPICAL (2) PLACES (TYPE 1 & 12) (4) PLACES TYPICAL

19 SED2 Legacy Variable Frequency Drives Energy & Atmosphere Important Note: VFD products are only available through authorized distribution channels. To locate an authorized distributor, please contact a Siemens Building Technologies representative at: SED2 Family. Features Built-in SBT P1 and JCI N2 (Metasys ) building automation system protocols for easy network integration LON, Modbus RTU Interfaces optional Low harmonics design reduces noise and interference; eliminates need for filters/reactors in most installations Built-in PID for fast and accurate pressure control Pump staging for open loop, constant pressure, and constant flow-type applications Multi-level program access Belt failure detection with or without an external sensor Service mode for applications requiring continuous, uninterruptible operation Accepts a wide variety of digital and analog I/O types, including direct Siemens Ni 1000 RTD sensor level inputs One common interface throughout all power ranges Optional Advanced Operator Panel for uploading/ downloading parameters Full form C relay contacts for digital outputs Options LON Interface Modbus RTU Interface Advanced Operator Panel (AOP) Module PC Kit C-19

20 Specifications C-20 Input Voltage and Power Ranges (3 phase) 208V and 230V to 240V, 3 ac±10%...1 hp to 60 hp 380V to 480V, 3 ac ±10%...1 hp to 125 hp 500V to 600V, 3 ac ±10%...1 hp to 125 hp Input Frequency...47 Hz to 63 Hz Output Frequency...0 Hz to 150 Hz Power Factor VFD degree of efficiency... 96% to 97% Switch-on Current... Less than nominal input current Auxiliary Supply 24V... Glavanically separated, unregulated auxiliary supply (18V to 32V) 100 ma Overload Capacity...110% for 60 seconds Control Method...Linear, parabolic and programmable V/f; and flux current control low-power mode PWM Frequency...2k Hz to 16k Hz (adjustable in 2k Hz increments) Fixed Frequencies programmable Skip Frequency Bands... 4 programmable Setpoint Resolution Hz digital 0.01 Hz serial 10 bit analog Digital Inputs (Sink/Source)...6: fully programmable and scalable isolated digital inputs, switchable Analog Inputs...2: 0 to 10 Vdc, 0/4 to 20 ma, can also be configured as digital inputs or Ni 1000 input Relay Outputs...2: configurable 30 Vdc/5A (resistive), 250 Vac/2A (inductive) Analog Outputs...2: programmable (0/4 ma to 20 ma, or 0 Vdc to 10 Vdc) Serial Interface...RS-485 transmission rate: Up to 38.4k Baud Protocols: USS, P1 and N2 Protection Level... IP20 NEMA Type 1 with protective shield and gland plate installed Temperature Ranges...Operating: 14 F to 104 F ( 10 C to 40 C) Storage: 40 F to 158 F ( 40 C to 70 C) Humidity...95% rh, non-condensing Operational Altitudes...Up to 3280 ft (1000m) above sea level without derating Protection Features...Under-voltage, Over-voltage, Overload, Ground fault, Short circuit, Stall prevention, Locked motor, Motor overtemperature l 2 t PTC, Over-temperature, Parameter PIN protection. Standards... UL, cul, CE, C-tick CE Conformity...Conformity with EC Low Voltage Directive 73/23/EEC Options...LON Interface, Modbus RTU Interface, BACnet MS/TP Interface, Advanced Operator Panel (AOP) Module, PC Kit Product Ordering Your Product Number Example Product Number S E D / 2 2 X Model SED2- kw rating VFD only 0.75, 1.1, 1.5, 2.2, 3, 4, 5.5, 7.5, 11, 15, 18.5, 22, 30, 37, 45, 55, 75, 90 [See Note 1 for these selections] Voltage to 240V to 480V to 600V (Uses 2 to 4 spaces plus a divider / ) NEMA rating 2 (IP 20) 1 NEMA Type 1 Filter X Factory Required Designator Notes: Example Shown: 1. Available only with Voltage Codes 3 and 4. SED2-0.75/22X = SED2 VFD only, 0.75 kw (1 hp), 200 to 240V, open type IP20.

21 Frame Sizes SED2 IP20 and NEMA Type 1 Frame Sizes and Power Ranges VFD0163R1 HP kw V A B C D E F N/A 480V A B C 575V C D E F Dimensions and Weights IP20 SED2 VFDs Frame Size Height Width Depth Weight Lb. (kg) A 6.8 (173) 2.9 (73) 5.9 (149) 2.9 (1.3) B 8.0 (202) 5.9 (149) 6.8 (172) 7.5 (3.4) C 9.6 (245) 7.3 (185) 7.7 (195) 12 (5.5) D 20.5 (520) 10.8 (275) 9.6 (245) 35 (16) E 25.6 (650) 10.8 (275) 9.6 (245) 44 (20) F 33.5 (850) 13 (350) 12.6 (320) 116 (53) C-21 NEMA Type 1 SED2 VFDs Assembled with Protective Shield and Gland Plate Frame Size Height Width Depth Weight Lb. (kg) A 9.1 (231) 2.9 (73) 5.9 (149) 3.2 (1.5) B 11.8 (300) 5.9 (149) 6.8 (172) 8.3 (3.8) C 13.8 (351) 7.3 (185) 7.7 (195) 13.6 (6.2) D 24.6 (625) 10.8 (275) 9.6 (245) 37.5 (17) E 29.7 (754) 10.8 (275) 9.6 (245) 46.4 (21) F 54.5 (1384) 16.0 (406) 14.0 (356) 200 (91)

22 C-22 Online order tracking This handy online feature stores all your past and current orders online for quick and easy reference. The Order Tracker function lets you access information such as: Ordered By Order No. Shipping Date Date Placed Acknowledgement of Order Shipment Tracking To view your history and status, register online at

23 SED2 Legacy with Bypass Options Energy & Atmosphere Important Note: VFD products are only available through authorized distribution channels. To locate an authorized distributor, please contact a Siemens Building Technologies representative at: SED2 with Conventional Bypass Options Family. Bypass Power 3-Contactor: Input, Output, & Bypass Overload protection in bypass mode Step-down transformer with fused primary and secondary Contactors electrically and mechanically interlocked Drive test function Complete electrical isolation of drive Input Device Fused disconnect Circuit breaker (optional) All doors are interlocked and padlockable Reactor Options Input line reactor mounted in bypass option enclosure. Line reactor supplied separately. Load reactor (in NEMA 1/3R enclosure) supplied separately. E-Bypass Control Auto Bypass Relay logic allows user to send the motor to bypass mode based on the drive s programmable relay. The drive s programmable relay, typically set to fault, can be set up for applications that run full speed for an extended period of time. put evice Drive Motor 3 Contactor Bypass Input Device Essential Services Mode Also used for smoke purge; the motor goes to bypass regardless of the selected mode. No call to stop will have an effect, including open safety or stop commands. Only turning the power off or opening this contact will stop the motor. Conventional Bypass Control Enable Input Generally used for safety tie-ins; the motor will not operate the drive or bypass when open. Essential Services Mode Typically used for smoke purge; the motor goes to bypass regardless of the selected mode. No call to stop will have an effect, including open safety or stop commands. Only turning the power off or opening this contact will stop the motor. Conventional Bypass Door Mounted Control Devices Drive-Off-Bypass selector Bypass pilot light Drive Test on/off selector C-23 Enable Input Generally used for safety tie-ins; the motor will not operate the drive or bypass when open. Common Remote Start/Stop Common remote start/stop can be used in both drive and bypass mode.

24 with Conventional Bypass Option Specifications Electronic Bypass Specifications Input Voltage (3-phase) 208V, 3 AC±10%...1 hp to 60 hp (2.3 amps to 154 amps) 240V, 3 AC±10%...1 hp to 60 hp (2.3 amps to 154 amps) 480V, 3 AC ±10%...1 hp to 125 hp (1.2 amps to 178 amps) 575V, 3 AC ±10%...1 hp to 125 hp (2.3 amps to 125 amps) Protection Level...NEMA Type 1 Digital Inputs Six Digital Inputs as follows...remote start input, Remote safety 1, Remote safety 2, Interlock start, Essential services, Overload trigger. Inputs require a contact closure capable of providing a low impedance path at currents less than 20 ma. Relay/Digital Outputs Six Relay/Digital Outputs as follows...vfd fault, Programmable output, Drive select, Bypass select, Running on bypass, Overload fault, Each relay has a maximum rating of 2A at 120Vac. Conventional Bypass Specifications Input Voltage (3-phase) 208V, 3 AC±10%...1 hp to 60 hp (2.3 amps to 154 amps) 240V, 3 AC±10%...1 hp to 60 hp (2.3 amps to 154 amps) 480V, 3 AC ±10%...1 hp to 125 hp (1.2 amps to 178 amps) 575V, 3 AC ±10%...1 hp to 125 hp (2.3 amps to 125 amps) Protection Level...NEMA Type 1 Temperature Operating to 104 F (0 to +40 C) Storage to +158 F (-40 to +70 C) Humidity...0 to 95% RH, non-condensing E-Bypass Door Mounted Control Devices C-24 VFD Bypass VFD0097R2 Input On/Off Enable STOP RESET VFD Input Contactor Output Contactor Bypass Contactor Motor Auto Bypass Enabled Essential Services Overload Relay Hand Start Remote Start VFD Fault Safety Fault Overload Fault Enable Commanded Proofed INTERLOCK START LOGIC Accessories & Service Kits C-35

25 Legacy with Conventional Bypass Option Product Ordering Your Product Number Example Product Number V B A B X Model VB VFD with an Extended Box Series A E Conventional Bypass Electronic Bypass Voltage HP rating V to 240 V to 480 V to 600 V 1.0, 1.5, 2.0, 3.0, 4.0, 5.0, 7.5, 10, 15, 20, 25, 30, 40, 50, 60, 75, 100, 125 [See Note 1 for these selections] Disconnect F B Fused Disconnect Circuit Breaker C-25 NEMA rating 1 NEMA Type 1 Contactor Notes: 3 3 Contactors (Input, output, and bypass contactors) 0 None (Extended box only. No bypass.) Reactor [See Note 3] 0 None 3 Line Reactor Filter X Factory Required Designator 1. Available only with Voltage Codes 3 and Input line reactors will be installed in bypass enclosures. Load reactors are supplied seperately in NEMA 1 or NEMA 3R enclosures. Example shown: VBA340.B133X VBA Conventional Bypass, 40 HP, 480V, Circuit Breaker, NEMA Type 1, 3-Contactor Bypass with Input Line Reactor. VBE340.F130X VBE Electronic Bypass, 40 hp, 480V, fused disconnect, NEMA Type 1, 3 contactors bypass, no reactor.

26 NEMA 1 Bypass Approximate Weights Frame Size Wt. Lb (kg) A 45 (20) B 55 (25) C 75 (34) D 150 (68) E 180 (82) F 470 (213) Note: Exact weight will be affected by the actual horsepower/voltage and the selected power options. NEMA 1 Bypass Frame Sizes and Power Ranges C-26 HP kw 208/240V 480V 575V 1.75 A A B B 5 4 C C C D E D D F E E F N/A F HA1 N/A

27 NEMA 1 Dimensions Depth With Handle 9.6 (24) = Protective Shield 13.2 (34) 1.5 (3.8) Depth With Handle 9.6 (24) 11.5 (29) Depth With Handle (26) (2.5) 2 (5) 20.8 (53) 2.9 (7.4) 4 (10) 34 (86) 10.5 TYP (27) 48 (122) 11 TYP (28) 53.5 (136) 11.5 TYP (29) 12.4 (31) 1.5 (3.8) 10.6 (27) 2 (5) 19.9 (51) 3.4 (8.6) Frame Size A and B Frame Size C Frame Size D C-27 Depth With Handle 12.2 (31) 58.5 (149) 20.8 (53) 2.9 (7.4) 3 (7.6) 10 TYP (25) 57.5 (146) 45.5 (116) Depth 17.4 (44) VFD0127R (51) Frame Size E 5.5 (14) Frame Size F Dimensions shown in inches (mm).

28 C-28 We re happy to assist you Our customer support teams are accessible and happy to assist you with ordering, fulfillment, and shipping questions. Call a representative at from 7 am to 5:30 pm (CST) Monday through Friday. Contact Customer Support or your Account Executive with any questions. We appreciate your business and look forward to helping you!

29 SED2 Legacy VFD NEMA Type 3R & Type 3R Harsh Environment (3RHE) Bypass Energy & Atmosphere Important Note: VFD products are only available through authorized distribution channels. To locate an authorized distributor, please contact a Siemens Building Technologies representative at: SED2 NEMA Type 3R Bypass. Features Bypass Power 3-Contactor: Input, Output, and Bypass Overload protection in bypass mode. Step-down transformer with fused primary and secondary. Contactors electrically and mechanically interlocked. Drive test function. Complete electrical isolation of drive. Input Device Fused disconnect. All doors are interlocked and padlockable. Reactor Options Line reactor mounted in bypass enclosure. Line reactor supplied separately (in NEMA Type 3R enclosure). Load reactor supplied separately. Bypass Door Mounted Control Devices Drive-Off-Bypass selector Bypass pilot light Drive Test On-Off selector C-29

30 NEMA Type 3R/3RHE Bypass Specifications Input Voltage (3 phase) V, 3 AC ±10% * 240V, 3 AC ±10% * 480V, 3 AC ±10% 575V, 3 AC ±10%* * Not available in the 3RHE models Protection Level...NEMA Type 3R Temperature Operating...14 F to 104 F ( 10 C to 40 C), HT1 to 122 F (50 C) Storage F to 158 F ( 40 C to 70 C) High-Temperature Model (HT1 and HT2) Operating...14 F to 122 F ( 10 C to 50 C) Storage F to 158 F ( 40 C to 70 C) Humidity...0 to 95% rh, non-condensing C-30

31 VFD NEMA Type 3R & Type 3R Harsh Environment (3RHE) Bypass Product Ordering Your Product Number Example Product Number V B A F X H E 2 Model VB VFD with an Extended Box Series A Conventional Bypass Voltage V to 240 V to 480 V to 600 V HP rating Disconnect F 1.0, 1.5, 2.0, 3.0, 4.0, 5.0, 7.5, 10, 15, 20, 25, 30, 40, 50, 60, 75, 100, 125 [See Note 1 for these selections] Fused Disconnect C-31 NEMA rating 3 NEMA Type 3R Contactor 0 None 3 3 Contactors (Input, output, and bypass) Reactor [See Note 2] 0 None 3 Line Reactor Filter X Factory Required Designator Options (If no option is required, leave field blank) HT1 High Temperature [See note 3] HE2 Harsh Enviroment Nema 3R [See note 4] HT2 Harsh Enviroment Nema 3R High Temperature Rating [See note 5] Notes: 1. Available only with Voltage Codes 3 and Input line reactors will be installed in bypass enclosures. Load reactors are supplied seperately in NEMA 1 or NEMA 3R enclosures. 3. HT1 (122 F, 50 C) is not available for all ratings. 208V and 230 to 240V to 3 hp are all HT1; 480V to 5 hp are all HT1. 4. HE2 available only with Voltage Codes 3 and 4. (480V to 40 hp) 5. HT2 (122 F, 50 C) is not available for all ratings. 480V to 5 hp are all HT2 Example Shown: VBA340.F330XHE2 VBA Conventional Bypass, 480V, 40 hp, fused disconnect, NEMA Type 3R, 3 contactors, no reactor, harsh environment.

32 NEMA Type 3R Enclosure Dimensions Enclosure Frame ABC Enclosure Frame DE Enclosure Frame F 34 (864) 18 (457) 46 (1169) 30 (762) 58 (1473) 42 (1067) 30 (762) 28-1/2 (724) Depth = DEPTH 11-1/2 = Inches 11-1/2 (292) 57 (1448) 56-1/8 (1425) 75 (1905) 74-1/8 (1882) C-32 VFD0178R2 MOUNTING CLEARANCE Depth DEPTH = 12-1/2 = 12-1/2 Inches (318) (318) FOR PROPER AIRFLOW: LEAVE 1 FOOT (305 mm) BETWEEN THE NEMA TYPE 3R BYPASS AND ANY ADJACENT SOLID STRUCTURE THAT IS NOT USED FOR MOUNTING PURPOSES. LEAVE 3 FEET (914 mm) BETWEEN THE NEMA TYPE 3R BYPASS AND ANY OTHER NEMA TYPE 3R BYPASS OR VFD. Depth = DEPTH 16-1/2 = Inches 16-1/2 (419) NEMA Type 3RHE Enclosure Dimensions 30 (756) 29 (724) Enclosure Frame B Enclosure Frame C Enclosure Frame D 34 (848) 18 (457) 51 (1288) 50 (1272) 42 (1051) 26 (660) 57 (1440) 56 (1424) 44 (1099) 28 (711) VFD0222R1 VFD0225R1 VFD0228R1 Depth = 10 Inches Depth = 11 Inches Depth = 14 Inches Dimensions shown in inches (mm).

33 NEMA Type 3R and 3RHE Approximate Weights 3R Frame Size Wt. Lb (kg) 3RHE Frame Size Wt. Lb (kg) ABC 130 (59) B 150 (68) DE 300 (136) C 220 (100) F 550 (249) D 330 (150) Note: Exact weight will be affected by actual horsepower/voltage and selected power options VFD0179R2 NEMA Type 3R Bypass Non-HT1 Enclosure Frame Sizes and Power Ranges HP kw /240V 480V (Rated as HT1, High Temperature package) (Rated as HT1, High Temperature package) ABC DE F N/A ABC DE F 575V ABC DE F C-33 VFD0180R2 VFD0180R2 NEMA Type 3R Bypass HT1 Enclosure Frame Sizes and Power Ranges HP kw /240V ABC DE F N/A 480V ABC DE F N/A 575V ABC DE F N/A NEMA 3RHE Bypasses HE2 Frame Sizes and Power Ranges HP kw /240V N/A 480V N/A C D N/A 575V N/A NEMA 3RHE Bypasses HT2 Frame Sizes and Power Ranges VFD0180R2 HP kw /240V N/A 480V N/A B C D N/A 575V N/A

34 C-34 Online 24/7 ordering convenience Use this Master HVAC Catalog and Siemens online ordering to maximize ordering efficiency. Go online to: Place orders Browse this catalog online Check product availability and pricing Specify FREE valve tagging Download invoices Track shipments Print out product information for submittals Link to technical documentation Download installation instructions Create a reusable template order form for frequently ordered parts See how easy it is to save time and money. Register today at:

35 Table of Contents Accessories & Service Kits PRODUCT PAGE # BT300 NEW! PC Cable for Software Tools C-36 Real Time Clock Battery Package C-36 Door Panel Kit C-36 Hand Held Panel Kit C-36 Flange Mounting Kits C-36 Varnished Option Boards C-37 SED2 to BT300 Migration Kits C-38 SED2 PC Kit C-39 C-35 Mounting Hardware C-39 Filter Kits C-39 Operator Panel C-39 LON Interface Option C-40 Modbus Interface C-40

36 Accessories and Service Kits BT300 Description PC Cable for Software Tools, USB to RS-485, 3m Part No. BT300-CABLE Battery package, 5 pcs BT300-BATTERY Door Panel Kit, Drive Side IP54 Protected, 3m BT300-PANEL-N12 C-36 Hand Held Panel Kit Flange Mounting Kit, for FS4 Flange Mounting Kit, for FS5 Flange Mounting Kit, for FS6 Flange Mounting Kit, for FS7 BT300-HHPANEL BT300-FLG-FS4 BT300-FLG-FS5 BT300-FLG-FS6 BT300-FLG-FS7

37 BT300 Description Part No. 6 X DI/DO, Programmable BT300-OPT-B1-V 2 X RO + Thermistor BT300-OPT-B2-V 1 X AI, 2 X AO (Isolated) BT300-OPT-B4-V 3 X RO BT300-OPT-B5-V C-37 1 X RO, 5 X DI (42-240VAC) BT300-OPT-B9-V LonWorks BT300-OPT-C4-V 1xAO, 1xDO, 1xRO BT300-OPT-BF-V NI1000 Sensor Card BT300-OPT-BH-V

38 Accessories and Service Kits BT300 Description SED2 208V to 3HP 480V to 5HP Part No. SED2-BT300-AB-4 SED2 208V to 4HP 480V to 7.5HP SED2-BT300-C-4 SED2 208V to 10HP 480V to 20HP SED2-BT300-C-5 C-38 SED2 208V 15 to 20hp 480V 25 to 40hp SED2-BT300-D-6 SED2 208V 25hp SED2 208V 30hp 480V 50 to 60hp SED2 FSC to BT300 Remote Mount SED2-BT300-D-7 SED2-BT300-E-7 SED2-BT300-C-R SED2 FSD and FSE to BT300 Remote Mount SED2-BT300-DE-R SED2 208V 40hp 480V 75hp SED2-BT300-F-7 SED2 208V 50 to 60hp 480V 100 to 125hp SED2-BT300-F-8

39 SED2 PC Kit. Description Part No. SED2-PC-KIT Gland Plates. (included with NEMA Type 1) Frame A Frame B Frame C SED2-GL-A SED2-GL-B SED2-GL-C Protection Shield. (included with NEMA Type 1) Frame A Frame B Frame C Frame D, E SED2-PS-A SED2-PS-B SED2-PS-C SED2-PS-DE C-39 NEMA Type 1 and 3R Enclosed Reactors. Contact Sales Partners NEMA Type 3R Floor Mounting Kit. Frames A, B, C BOP/AOP Door Mounting Kits. BOP/AOP Single Inverter SED2-DOOR-KIT1 AOP Multi-Inverter SED2-DOOR-KIT2 Operator Panel. Basic Operator Panel (included with all SED2s) Advanced Operator Panel (AOP) SED2-BOP1 SED2-AOP1

40 Accessories and Service Kits SED2 LON Interface Option. Description Part No. SED2-LONI/F Modbus RTU Interface Module for SED2. SED2-MODBUS2 C-40 SED2 Modbus Configuration Kit. SED2-MODBUS2_KIT