PRODUCT DESCRIPTION SPECIFICATIONS INSTALLATION. Dialer codes PRODUCT DIAGRAM. DL2 Dialer Module Digital Alarm Communicator Transmitter. Warning!

Transcription

1 PRODUCT DESCRIPTI The DL is a dialer module, which contains a Digital Alarm Communicator Transmitter (DACT). The dialer sends alarm, supervisory, and trouble information to a compatible Digital Alarm Communicator Receiver (DACR) through one or two dial-up telephone lines (two per NFPA ). The dialer supports PPS / format and Dual Tone Multi-Frequency (DTMF) or Pulse mode dialing. Every hours, the dialer performs an automatic test call to verify communications between the fire alarm panel and the Central Monitoring Station (CMS). INSTALLATI Disconnect external ac power and battery power to cabinets before installing or removing components. Failure to do so may result in serious injury or loss of life.! Carefully match mounting holes up with spacers to ensure proper connector mating. Mounting the DL Install three metal spacers (P/N 69) in the three locations indicated below. Mount the DL on the three metal spacers. Mate connector P on the DL with connector JE on the Main Controller Module. Secure the DL to the spacers with the screws provided. JE Warning! Caution! Observe static-sensitive material handling practices. Install metal spacers here. with the screws provided Input power Supervisory Active Mounting Phone line Wall connector Line supervision Communications protocol CMS telephone numbers FCC registration number Dialing retries Clock accuracy Compliance Programming phone Environmental conditions Temperature range Humidity range Event SPECIFICATIS ma ma Mounts on the Main Controller Module One/two loop start lines on public switched telephone network, pulse or DTMF dialing. Party, ground start, and PBX start lines are not acceptable. NFPA requires two phone lines. Standard RJX or RJ8X phone jack Trouble when line voltage less than V and line current less than ma. SIA pulse format PPS / double round, Hz handshake, 9 Hz carrier Two -digit numbers ZUSA-9-AL-E five to ten Within one hour/year Communications Canada, CS-; FCC/CFR parts and 68; NFPA ; UL 86; ULC S-M8 Any tone dial phone with an RJ plug to F ( to 9 C) to 9%, non-condensing Dialer codes Code Fire alarm report codes - Fire alarm restore codes - Normal hr check-in 9 Abnormal hr check-in 9 Supervisory alarm 9 Trouble 9 Trouble / supervisory restore 9 AC power fail 96 Battery trouble 9 Telephone line trouble 98 Dialer disabled 99 PRODUCT DIAGRAM Main Controller Module P Dialer DL -X Metal spacer P JE -X /6 panhead screw INSTALLATI SHEET: DL Dialer Module Digital Alarm Communicator Transmitter INSTALLATI SHEET P/N: 8 REVISI LEVEL:. DATE: AUG FILE NAME: 8.CDR APPROVED BY: M. Slack CREATED BY: B. Graham Main Controller Module EDWARDS SYSTEMS TECHNOLOGY, INC. SARASOTA, FL: 9-9- FAX CHESHIRE, CT: FAX OWEN SOUND, CANADA: 9-6- FAX INTERNATIAL, CANADA: 9-- FAX 9--9

2 WIRING Notes Connect J and J to RJX or RJ8X telephone jacks installed by an authorized telephone company representative (CAA or CA8A in Canada). Install the RJX (RJ8X) jacks within ft (. m) of the control panel and allow two extra feet of cable for a total of ft (. m). The dialer installation kit includes a protective bushing (P/N 66) for enclosure knockouts. Before programming can proceed, the dialer will notify the central monitoring station (CMS) for any previously entered numbers. Ring (red) RJX 8 pin modular connector for phone line Tip (green) Black Surge protector Yellow To phone line wired same as phone line Premises phones Ring (red) RJX 6 8 pin modular connector for phone line No T-taps! Surge protector ft (. m) Use J when using only one phone circuit Tip (green) J J J # Programming phone The phone key pad is only for module programming. Rotary dial phones will not work. See dialer programming, on the following pages, for more information. Enable/disable switch Dialer Status LED FCC information The dialer complies with Part 68 of the FCC rules. The Dialer's FCC registration number and Ringer Equivalence Number (REN) are on the back of the dialer. This information must be provided to the telephone company if requested. An FCC compliant telephone cord and modular plug cord is supplied with the dialer. The dialer is designed to be connected to the telephone network using the supplied cord and an RJX or RJ8X jack, which must also comply with FCC Part 68 rules. The REN is used to determine the quantity of devices which may be connected to the telephone line. Excessive RENs on the telephone line may result in the devices not ringing in response to an incoming call. In most, but not all areas, the sum of RENs should not exceed five (). To be certain of the number of devices that may be connected to a line as determined by the total RENs, contact the local telephone company. If the dialer causes harm to the telephone network, the telephone company will notify you an advance that temporary discontinuance of service may be required. If advance notice is not practical, the telephone company will notify you as soon as possible. You will also be advised of your right to file a complaint with the FCC, if you believe it is necessary. The telephone company may make changes in it's facilities, equipment, operations, or procedures that could affect the operation of the dialer. If this happens, the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service. 6 If trouble is experienced with the dialer, for repair or warranty information, contact GS Building Systems Corp. 6 Parkland Drive, Sarasota, Florida USA. If the dialer is causing harm to the telephone network, the telephone company may request you disconnect the dialer until the problem is resolved. No repairs may be performed on the dialer by the user. IMPORTANT INFORMATI 8 The dialer can not be used on public coin phones or party line service provided by the telephone company. Canada DOC information Notice: The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational, and safety requirements. The Department does not guarantee the equipment will operate to the user's satisfaction. Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations. Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment. Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines, and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas. Caution: Users should not attempt to make connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate. Notice: The Load Number (LN) assigned to each terminal device denotes the percentage of the total load to be connected to a telephone loop which is used by the device to prevent overloading. The temination on a loop may consist of any combination of devices subject only to the requirements that the sum of the Load Numbers of all devices does not exceed. P/N: 8 REV:. Page of

3 A confirmation tone indicates the correct entry of a program item. DIALER PROGRAMMING Phone lines must be loop start on a public-switched network. PBX, party lines, and ground start lines are not acceptable. The dialer does not place calls, monitor the panel, or monitor the phone lines during the programming process. After initial programming, the dialer notifies the central monitoring station that it is disabled before programming can proceed. Two phone lines are required to comply with NFPA. Notes 6 The dialer will automatically switch to pulse dialing after three consecutive failures using tone mode. It will switch back to tone dialing after failing to connect using pulse mode, upon re-programming, or upon enabling disconnect switch. Entering the programming mode Connect the phone to J. Take the handset off the hook. J The status LED will display two rapid green flashes, and then turn solid green. J J Entering the password When the Status LED turns solid green, press (GSBS) on the telephone keypad. Entering the dialer data Listen for the confirmation tone to verify that the dialer has accepted the password. Note: Enter the required information for all 8 programming items in sequence. Before programming can proceed, the dialer will notify the CMS for any previously entered numbers. The status LED will display a slow green flash during the dialing process. The status LED will display a steady green LED to indicate that the dialer is ready for programming. Programming the primary site ID number (item ) Press the following telephone keys: Listen for the confirmation Make sure that the status LED displays a steady green pattern entered. interrupted by amber flashes. Enter the -digit ID number on the telephone keypad. Use leading zeroes as required. Programming the primary CMS number (item ) Press the following telephone keys: Listen for the confirmation Make sure that the status LED displays a steady red pattern entered. interrupted by amber flashes. Enter a to -digit number on the telephone keypad to specify the primary CMS number. Programming the secondary site ID number (item ) Press the following telephone keys: Listen for the confirmation Make sure that the status LED displays a steady green pattern entered. interrupted by double amber flashes. Enter the -digit ID number on the telephone keypad. Use leading zeroes as required. Programming the secondary CMS number (item ) Press the following telephone keys: Listen for the confirmation Make sure that the status LED displays a steady red pattern entered. interrupted by double amber flashes. - Continued - P/N: 8 REV:. Page of Enter a to -digit number on the telephone keypad to specify the secondary CMS number.

4 Programming or line operation (item ) Press the following telephone keys: Listen for the confirmation Make sure that the status LED displays a steady green pattern entered. interrupted by rapid amber flashes. Enter or on the telephone keypad. The default setting is. Programming the number of CMS retry calls (item 6) Press the following telephone keys: Listen for the confirmation Make sure that the status LED displays rapid green flashes. entered 6. 6 Enter, 6,, 8, 9, or on the telephone keypad. The default is (). Programming the retry interval (item ) Press the following telephone keys: Listen for the confirmation Make sure that the status LED displays double green flashes. entered. Enter,, or 6 on the telephone keypad to specify the number of seconds. The default is. Programming the daily supervision delay (item 8) Press the following telephone keys: Listen for the confirmation Make sure that the status LED displays a slow amber flash. entered 8. 8 Enter a -digit number on the telephone keypad to specify the delay period (in hours). The default is. Exiting the programming mode Disconnect the phone from J. J J J Put the handset on the hook. Status LED indications during dialer operations Color Green Green Amber Pattern Rapid flash Single flashes Single flashes Description Waiting for password entry Call to CMS in progress Dialer in trouble Amber Double flashes Dialer disabled Restoring default values Enter the password Press the following telephone keys: according to the preceding instructions on this installation sheet. Verifying programmed entries Enter the password according to the preceding instructions on this installation sheet. Press the following telephone keys: Programming item number # Make sure that the status LED displays a steady green pattern. Listen for the confirmation tone to verify that it sounds the contents of the selected item through the handset. The dialer resets to its default values and returns it to item of the programming mode. Testing the dialer Activate and open an SDC and an NAC to verify that the CMS receives the proper signal. Verify that failure of the primary signal path results in the transmission of a trouble signal through the secondary signal path within minutes. Verify that failure of the secondary signal path results in the transmission of a trouble signal through the primary signal path within minutes. Notes The primary signal path is along the phone line connected to J. The secondary signal path is along the phone line connected to J. P/N: 8 REV:. Page of

5 INSTALLATI Mount the LED/switch modules. Inner door (side view) Inner door (rear view) Plunger Grommet Note: Do not try to insert the plunger and grommet into the mounting holes at the same time. Insert the grommet first and then the plunger to avoid damaging them. LED/switch module (side view) LED/switch module (rear view) Dip switch J J J J J J J J J J J J J J -LCD To Main Controller Module Connect the LED/Switch Module ribbon cables Connect the ribbon cable from J on the -LCD to J on the first module. Connect the ribbon cable from J on the first module to the J on the second module. Repeat step until you reach the last module. Note: White indicates the correct dipswitch position. Set the dip switches on the LED/switch modules. Dip switch setting LED addresses Switch addresses PRODUCT DESCRIPTI The front panel LED/switch modules consist of 6 individual LEDs for point annunciation. The LED/switch modules provide eight groups of two LEDs combined with a switch. See the specifications for available LED color options. The protected slip-in label next to each LED/switch identifies its function. Communication with the Main Controller Module requires no point to point wiring, because it is multiplexed using plug-in ribbon cables. Any combination of three annunciator and switch modules may be mounted on the panel's inner door. Blank Plates (model -FBP) fill unused inner door spaces. Models -RY -6G -6R -6Y -8RY -FBP Models -6G8S -6R8S -6Y8S -8GYS -8RYS SPECIFICATIS LED/switch options Model Description -RY red LEDs over yellow LEDs -6G 6 green LEDs -6G8S 6 green LEDs and 8 switches -6R 6 red LEDs -6R8S 6 red LEDs and 8 switches -6Y 6 yellow LEDs -6Y8S 6 yellow LEDs and 8 switches -8RY 8 red LEDs over 8 yellow LEDs -8RYS 8 red / 8 yellow alternating LED/switch pairs -8GYS 8 green / 8 yellow alternating LED/switch pairs Blank plate option Switches Temperature range Humidity range -FBP Momentary push button to F ( to 9 C) to 9%, non-condensing INSTALLATI SHEET: Front Panel LED(/Switch) Modules INSTALLATI SHEET P/N: REVISI LEVEL:. DATE: JUN Related documentation: -LCD installation sheet EDWARDS SYSTEMS TECHNOLOGY, INC. SARASOTA, FL: 9-9- FAX CHESHIRE, CT: FAX OWEN SOUND, CANADA: 9-6- FAX INTERNATIAL, CANADA: 9-- FAX 9--9 FILE NAME:.CDR APPROVED BY: J. Massing CREATED BY: B. Graham

6