Legacy Debug Adapters

Transcription

1 Legacy Debug Adapters User Manual V1.1

2 This document and all documents accompanying it are copyrighted by isystem AG and all rights are reserved. Duplication of these documents is allowed for personal use. In all other cases, written consent from isystem is required. Copyright isystem AG. All rights reserved. All trademarks are property of their respective owners. isystem is an ISO 9001 certified company.

3 Contents Introduction pin 2.54 mm NXP ColdFire Debug Adapter pin 2.54mm NXP BDM Debug Adapter pin 2.54mm NXP S12Z BDM Debug Adapter pin 2.54mm NXP COP Debug Adapter pin Mictor PPC4xx RISCTrace D. Adapter pin 2.54mm Renesas 78K0R D. Adapter pin KEL Renesas V850 Debug Adapter pin 2.54mm Renesas 78K0 Debug Adapter K0 16-pin 2.54mm Adapter pin 2.54mm Renesas RL78 Debug Adapter pin ERNI ST STM8 Debug Adapter... 18

4 Introduction The ic5000 and the ic5700 BlueBox adapt to the specific target architecture and target debug connector through a dedicated debug adapter. This document provides detailed information on the debug adapters (used in conjunction with the ic5000 or the ic5700) supporting legacy microcontroller architectures which are no longer supported with winidea TM or newer. Listed debug adapters and belonging microcontroller architectures are supported with winidea TM or older. Detailed information on current debug adapters which are used in conjunction with the ic5000 and the ic5700 BlueBox, and supported by winidea TM or newer, is available in a separate user manual. Ordering Code IC50130 IC50140 IC50141 IC50153 IC50155 IC50170 IC50172 IC50174 IC50175 IC50190 Description 26-pin 2.54 mm NXP ColdFire Debug Adapter 6-pin 2.54mm NXP BDM Debug Adapter 6-pin 2.54mm NXP S12Z Debug Adapter 16-pin 2.54mm NXP COP Debug Adapter Mictor 38-pin PPC4xx RISCTrace Debug Adapter 16-pin 2.54mm Renesas 78K0R Serial Debug Adapter 26-pin KEL Renesas V850 Debug Adapter 10-pin 2.54mm Renesas 78K0 NXP Debug Adapter 14-pin 2.54mm Renesas RL78 NXP Debug Adapter 4-pin ERNI ST STM8 Debug Adapter For more information contact our sales team via sales@isystem.com This symbol is used within the manual to highlight important safety notices. 1

5 26-pin 2.54 mm NXP ColdFire Debug Adapter Ordering code IC50130 This debug adapter is used to connect the ic5000 BlueBox to NXP ColdFire based target featuring a 26-pin 2.54 mm pitch target debug connector with the ColdFire pinout. This debug adapter is supported by the ic5000 BlueBox only. The ic5700 doesn t support the ColdFire architecture. The debug adapter connects to the 25cm 40-pin ribbon cable coming from the BlueBox and to the target debug connector on the other side. Refer to the BlueBox User Manual for more details on connecting the debug adapter. The following pinout is valid on the target side: Signal direction Signal Pin Pin Signal Signal direction I Developer Reserved 1 2 ~BKPT O GND 3 4 DSCLK O GND 5 6 Developer Reserved RESET 7 8 DSI O I VDD_IO 9 10 DSO I GND PSTDDATA7 I I PSTDDATA PSTDDATA5 I I PSTDDATA PSTDDATA3 I I PSTDDATA PSTDDATA1 I I PSTDDATA GND Motorola Reserved Motorola Reserved GND PSTCLK I I NC ~TEA O 26-pin ColdFire target pinout Blue colored signals are trace signals. 2

6 When connecting the BlueBox to the new embedded target for the first time, double check that the debug adapter pinout matches with the target debug connector. Note that a mismatch can result in a hardware failure. 26-pin 2.54 mm NXP ColdFire Debug Adapter features resettable fuses on pins 2, 4, 7, 8, 9, 10, 24 and 26. These protect debug signals against overcurrent and cycle back to a conductive state after the excessive current fades away. Signals on pins 1, and 24 are protected via 47 ohm serial resistors. The debug adapter connects to the target via a 26-pin 2.54 mm connector, for example Yamaichi FAS A target should feature a matching part, for example WÜRTH ELEKTRONIK

7 6-pin 2.54mm NXP BDM Debug Adapter Ordering code IC50140 This debug adapter is used to connect the ic5000 and the ic5700 BlueBox to NXP HCS08, HC12, HCS12, S12X and ColdFire V1 based target featuring 6-pin 2.54mm pitch target debug connector with the BDM pinout. The debug adapter connects to the 25cm 40-pin ribbon cable coming from the BlueBox and to the target debug connector on the other side. Refer to the BlueBox User Manual for more details on connecting the debug adapter. The following pinout is valid on the target side: Signal direction Signal Pin Pin Signal Signal direction I/O BGND 1 2 GND NC 3 4 RESET I/O NC 5 6 VTref I 6-pin BDM pinout When connecting the BlueBox to the new embedded target for the first time, double check that the debug adapter pinout matches with the target debug connector. Note that a mismatch can result in a hardware failure. 6-pin 2.54mm NXP BDM Debug Adapter features resettable fuses on pins 1, 2, 4 and 6. These fuses protect debug signals against overcurrent and cycle back to a conductive state after the excessive current fades away. The debug adapter connects to the target via a 6-pin 2.54 mm connector, for example FCI LF. A target should feature a matching part, for example WÜRTH ELEKTRONIK

8 6-pin 2.54mm NXP S12Z BDM Debug Adapter Ordering code IC50141 This debug adapter is used to connect the ic5000 and the ic5700 BlueBox to NXP S12Z based target featuring 6-pin 2.54mm pitch target debug connector with the S12Z BDM pinout. The debug adapter connects to the 25cm 40-pin ribbon cable coming from the BlueBox and to the target debug connector on the other side. Refer to the BlueBox User Manual for more details on connecting the debug adapter. The following pinout is valid on the target side: Signal direction Signal Pin Pin Signal Signal direction I/O BGND 1 2 GND I PDO 3 4 RESET I/O I PDOCLK 5 6 VTref I 6-pin S12Z BDM pinout When connecting the BlueBox to the new embedded target for the first time, double check that the debug adapter pinout matches with the target debug connector. Note that a mismatch can result in a hardware failure. 6-pin NXP BDM Debug Adapter features resettable fuses on pins 1, 2, 4 and 6. These fuses protect debug signals against overcurrent and cycle back to a conductive state after the excessive current fades away. Signals on pins 3 and 5 are protected via 47 ohm serial resistors The debug adapter connects to the target via a 6-pin 2.54 mm connector, for example FCI LF. A target should feature a matching part, for example WÜRTH ELEKTRONIK

9 16-pin 2.54mm NXP COP Debug Adapter Ordering code IC50153 This debug adapter is used to connect the ic5000 BlueBox to NXP MPC6xx, MPC82xx, MobileGT, MPC7xx or MPC83xx based target featuring 16-pin 2.54mm pitch target debug connector with NXP COP pinout. This debug adapter is supported by the ic5000 BlueBox only. The ic5700 doesn t support the listed architectures. The debug adapter connects to the 25cm 40-pin ribbon cable coming from the BlueBox and to the target debug connector on the other side. Refer to the BlueBox User Manual for more details on connecting the debug adapter. The following pinout is valid on the target side: Signal direction Signal Pin Pin Signal Signal direction I TDO 1 2 QACK# O O TDI 3 4 TRST O I HALTED 5 6 VTref I O TCK 7 8 CKSTP_IN O O TMS 9 10 NC O SRESET GND O HRESET NC I CKSTP_OUT GND 16-pin COP target pinout When connecting the BlueBox to the new embedded target for the first time, double check that the debug adapter pinout matches with the target debug connector. Note that a mismatch can result in a hardware failure. 6

10 16-pin 2.54mm NXP COP Debug Adapter features resettable fuses on all pins except for the pin 15. These protect debug signals against overcurrent and cycle back to a conductive state after the excessive current fades away. The signal on the pin 15 is protected via 100 ohm serial resistor. The debug adapter connects to the target via a 16-pin 2.54 mm connector, for example Yamaichi FAS OBF. A target should feature a matching part, for example WÜRTH ELEKTRONIK

11 38-pin Mictor PPC4xx RISCTrace D. Adapter Ordering code IC50155 This debug adapter is used to connect the ic5000 BlueBox to Applied Micro PPC4xx based target featuring a 38-pin Mictor target debug connector with the PPC4xx RISCTrace pinout. This debug adapter is supported by the ic5000 BlueBox only. The ic5700 doesn t support the PPC4xx architecture. The debug adapter connects to the BlueBox through the two ribbon cables and to the target debug connector on the other side. Refer to the BlueBox User Manual for more details on connecting the debug adapter. The following pinout is valid on the target side: Signal direction Signal Pin Pin Signal Signal direction NC 1 2 NC NC 3 4 NC GND 5 6 TRCLK I O HALT 7 8 NC O SRST 9 10 NC I TDO VREF I NC NC O TCK NC O TMS NC O TDI NC O NTRST NC NC NC I BS TS0 I I BS TS1 I I BS TS2 I I BS TS3 I I BS TS4 I I BS TS5 I I BS TS6 I PPC4xx RISCTrace target pinout 8

12 Blue colored signals are trace signals. When connecting the BlueBox to the new embedded target for the first time, double check that the debug adapter pinout matches with the target debug connector. Note that a mismatch can result in a hardware failure. 38-pin Mictor PPC4xx RISCTrace Debug Adapter features resettable fuses on pins 7, 9, 11, 12, 15, 17, 19 and 21. These protect debug signals against overcurrent and cycle back to a conductive state after the excessive current fades away. Signals on pins 6, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34, 35, 36, 37 and 38 are protected via 47 ohm serial resistors. The debug adapter connects to the target via a 38-pin Mictor connector Tyco Electronics A target should feature a matching part, for example Tyco Electronics in the SMT technology. 9

13 16-pin 2.54mm Renesas 78K0R D. Adapter Ordering code IC50170 This debug adapter is used to connect the ic5000 and the ic5700 BlueBox to Renesas 78K0R based target featuring 16-pin 2.54mm pitch target debug connector with the 78K0R pinout. The debug adapter connects to the 25cm 40-pin ribbon cable coming from the BlueBox and to the target debug connector on the other side. Refer to the BlueBox User Manual for more details on connecting the debug adapter. The following pinout is valid on the target side: Signal direction Signal Pin Pin Signal Signal direction GND 1 2 RESET OUT O I/O TOOL0 (RxD/TxD) 3 4 Vcc I/O I/O TOOL0 (RxD/TxD) 5 6 NC NC 7 8 NC NC 9 10 NC NC NC NC FLMD0 O I RESET IN TOOL1 (CLK) I 16-pin 78K0R target pinout When connecting the BlueBox to the new embedded target for the first time, double check that the debug adapter pinout matches with the target debug connector. Note that a mismatch can result in a hardware failure. If the Supply 5V to the target option is checked in the Hardware/Emulation Options/CPU Setup/Advanced tab, the debugger supplies 5V at the Vcc pin (pin 4) on the target debug connector, which can be used to power the target. Maximum target current consumption should not exceed 50mA. If RESET IN (target reset detection) from the microcontroller is not connected to the target debug connector pin 15, 10k ohm pull-up must be connected to this pin or the debugger may exhibit unpredictable behavior. 10

14 16-pin 2.54mm Renesas 78K0R Debug Adapter features resettable fuses on all connected pins. These protect debug signals against overcurrent and cycle back to a conductive state after the excessive current fades away. The debug adapter connects to the target via a 16-pin 2.54 mm connector, for example Yamaichi FAS OBF. A target should feature a matching part, for example WÜRTH ELEKTRONIK

15 26-pin KEL Renesas V850 Debug Adapter Ordering code IC50172 This debug adapter is used to connect the ic5000 and the ic5700 BlueBox to Renesas V850 based target featuring 26-pin KEL target debug connector with the V850 pinout. The debug adapter connects to the 25cm 40-pin ribbon cable coming from the BlueBox and to the target debug connector on the other side. Refer to the BlueBox User Manual for more details on connecting the debug adapter. The following pinout is valid on the target side: Signal direction Signal Pin Pin Signal Signal direction Ground 1 2 Reserved Ground 3 4 Reserved Ground 5 6 Reserved Ground 7 8 Reserved Ground 9 10 Reserved Ground Reserved Ground DDI O Ground DCK O Ground DMS O Ground DDO I Reserved DRST O Reserved RESET O I Reference Voltage FLMD0 O 26-pin V850 target pinout When connecting the BlueBox to the new embedded target for the first time, double check that the debug adapter pinout matches with the target debug connector. Note that a mismatch can result in a hardware failure. 26-pin KEL Renesas V850 Debug Adapter features resettable fuses on all connected signals. These fuses protect debug signals against overcurrent and cycle back to a conductive state after the excessive current fades away. 12

16 The debug adapter connects to the target via a 26-pin KEL connector, part number 8825E A target should feature a matching part, for example KEL connector, part number 8830E S. For more details see the 8825E Series at 13

17 10-pin 2.54mm Renesas 78K0 Debug Adapter Ordering code IC50174 This debug adapter is used to connect the ic5000 and the ic5700 BlueBox to Renesas 78K0 based target featuring 10-pin 2.54mm pitch target debug connector with the 78K0 pinout. The debug adapter connects to the 25cm 40-pin ribbon cable coming from the BlueBox and to the target debug connector on the other side. Refer to the BlueBox User Manual for more details on connecting the debug adapter. The following pinout is valid on the target side: Signal direction Signal Pin Pin Signal Signal direction I RESET IN 1 2 RESET OUT O O FLMD0 3 4 TARVCC I I/O X2 5 6 GND O X1 7 8 GND I NC V OUT O 10-pin 78K0 target pinout When connecting the BlueBox to the new embedded target for the first time, double check that the debug adapter pinout matches with the target debug connector. Note that a mismatch can result in a hardware failure. If the Supply 5V to the target option is checked in the Hardware/Emulation Options/CPU Setup/Advanced tab, the debugger supplies 5V at the 5V OUT pin (pin 10) on the target debug connector, which can be used to power the target. Maximum target current consumption should not exceed 50mA. If RESET IN (target reset detection) from the microcontroller is not connected to the target debug connector pin 1, 10k ohm pull-up must be connected to this pin or the debugger may exhibit unpredictable behavior. 10-pin 2.54mm Renesas 78K0R Debug Adapter features resettable fuses on all connected pins. These protect debug signals against overcurrent and cycle back to a conductive state after the excessive current fades away. 14

18 The debug adapter connects to the target via a 10-pin 2.54 mm connector, for example Yamaichi FAS OBF. A target should feature a matching part, for example WÜRTH ELEKTRONIK K0 16-pin 2.54mm Adapter Embedded targets based on Renesas 78K0 microcontroller can also feature a 16-pin 2.54mm target debug connector with the Renesas 78K0 pinout. An adapter connecting at the end of the 10-pin 2.54mm Renesas 78K0 Debug Adapter is available for Renesas 78K0 16-pin pinout and must be ordered separately under the IAPIN10PIN16NEC78K ordering code. Toward the BlueBox the adapter features 10-pin 2.54 mm male connector featuring the 10-pin 78K0 pinout. Ordering code IAPIN10PIN16NEC78K The following pinout is valid on the target side: IAPIN10PIN16NEC78K adapter Signal direction Signal Pin Pin Signal Signal direction GND 1 2 RESET OUT O NC 3 4 TARVCC I NC 5 6 NC NC 7 8 NC O X NC NC NC I/O X FLMD0 O I RESET IN NC 16-pin 78K0 target pinout The adapter connects to the target via a 16-pin 2.54 mm connector, for example Yamaichi FAS OBF. A target should feature a matching part, for example WÜRTH ELEKTRONIK

19 14-pin 2.54mm Renesas RL78 Debug Adapter Ordering code IC50175 This debug adapter is used to connect the ic5000 and the ic5700 BlueBox to Renesas RL78 based target featuring 14-pin 2.54mm pitch target debug connector with the RL78 pinout. The debug adapter connects to the 25cm 40-pin ribbon cable coming from the BlueBox and to the target debug connector on the other side. Refer to the BlueBox User Manual for more details on connecting the debug adapter. The following pinout is valid on the target side: Signal direction Signal Pin Pin Signal Signal direction NC 1 2 GND NC 3 4 NC I/O TOOL0 5 6 RESET_IN I NC 7 8 VDD EVDD 9 10 RESET_OUT O NC GND O RESET_OUT GND 14-pin RL78 target pinout When connecting the BlueBox to the new embedded target for the first time, double check that the debug adapter pinout matches with the target debug connector. Note that a mismatch can result in a hardware failure. If the Supply 5V to the target option is checked in the Hardware/Emulation Options/CPU Setup/Advanced tab, the debugger supplies 5V at the VDD pin (pin 8) on the target debug connector, which can be used to power the target. Maximum target current consumption should not exceed 50mA. Some RL78 devices may have two power supply pins (EVDD and VDD). Both must be connected to the target debug connector, when the power is provided by the BlueBox. The EVDD voltage from the pin 9 is used as a target reference voltage when Vref option under the Debug I/O levels setting is checked in the Hardware/Emulation Options/Hardware tab. 16

20 If RESET IN (target reset detection) from the microcontroller is not connected to the target debug connector pin 6, 10k ohm pull-up must be connected to this pin or the debugger may exhibit unpredictable behavior. The debug adapter connects to the target via a 14-pin 2.54 mm connector, for example Yamaichi FAS OBF. A target should feature a matching part, for example WÜRTH ELEKTRONIK

21 4-pin ERNI ST STM8 Debug Adapter Ordering code IC50190 This debug adapter is used to connect the ic5000 and the ic5700 BlueBox to ST STM8 based target featuring 4-pin ERNI target debug connector with the STM8 pinout. The debug adapter connects to the 25cm 40-pin ribbon cable coming from the BlueBox and to the target debug connector on the other side. Refer to the BlueBox User Manual for more details on connecting the debug adapter. The following pinout is valid on the target side: Pin Signal Signal direction 1 VDD I 2 SWIO I/O 3 GND 4 RST O 4-pin ERNI ST STM8 target pinout When connecting the BlueBox to the new embedded target for the first time, double check that the debug adapter pinout matches with the target debug connector. Note that a mismatch can result in a hardware failure. 4-pin ERNI ST STM8 Debug Adapter features resettable fuses on all pins. These fuses protect debug signals against overcurrent and cycle back to a conductive state after the excessive current fades away. The debug adapter connects to the target via the ERNI MiniBridge 4-pin connector female (P/N ). A target should feature a matching part, for example ERNI MiniBridge 4-pin connector right angle male (P/N ) or ERNI MiniBridge 4-pin connector vertical male (P/N ). 18

22 isystem has made every effort to ensure the accuracy and reliability of the information provided in this document at the time of publishing. While isystem reserves the right to make changes to its products and/or the specifications detailed herein, it does not make any representations or commitments to update this document. isystem. All rights reserved.