Model : SR-2108B-24M-3 Before you begin, read all warnings and installation instructions and save for future use. Group 5: 4 channels

Transcription

1 HUEDA 24CH RDM DMX512 Decoder Model : SR-2108B-24M-3 Before you begin, read all warnings and installation instructions and save for future use V DC power input 2xRJ45 terminal: DMX512 signal input & output XLR3 DMX512 signal input & output HUEDA LED Group 1: Group 2: Group 3: Group 4: Group 5: Group 6: Safety & arnings This product is intended to be installed and serviced by a quali ed licensed electrician. stall in accordance with the ational Electric Code, and local regulations. Disconnect power before installing or servicing. Only power with a regulated (listed) constant voltage Class 2 power supply (12-24V DC). ever use this product with dimmable or magnetic dimmable power source(driver). Ensure applicable wire is installed between driver, xture, and any controls in between. hen choosing wire, factor in voltage drop, amperage rating and type (in-wall rated, wet location rated, etc.). adequate wire installation could overheat wires and cause re. This product is rated for indoor installation and only for dry locations. Avoid direct sun light. Do not modify this product beyond the instructions in this guide or the warranty will be voided. iring diagrams in this installation guide for basic installations. Please carefully review your installation before proceeding. 1. Product Features: Flicker free in 30K PM frequency, can be used for lm making. Master & decoder mode, RDM function. 24 Channel DMX 512 decoder. 2 can be set as same DMX address or different DMX address via digital display. Multiple DMX in/out ports: RJ 45, XLR and terminal blocks. 12 PM output channels, common anode. 8 bit and 16 bit PM output resolution ratio. 500Hz~30KHz output PM frequency. 0.1~9.9 gamma value curve. Galvanic isolation. 2. Product Parameter: put Voltage put Current put Power DC 12V~DC 24V (Use only with Class 2 regulated Power supply) 24 x 4A 24 x (48~96) Dimension L x 83 x H 42mm (L x 3.26 x H 1.65 ) 1/8

2 3. Product Dimension: 83mm (3.26 ) 42mm (1.65 ) 264.6mm (10.41 ) 4. Operation: Digital DMX address panel Set the device mode to Master or Decoder mode. Back Enter Up Down = DMX Decoder mode, = DMX Master mode(stand alone). Click Down button until run1 or run2 displayed on display, then click Enter. Click Down button to choose run1 or run2, then click Back button. After choosing run1 or run2, restart the device. 1) For run2 DMX Master mode: After restarting the device, pressing Up button to get following numbers on display: represents brightness for each output PM channel. First two digit 01 represents PM output channel 1 and it is selectable from 01 to by clicking UP or Down button. Last two digits 01 represents brightness level, click Enter button, the display ashes, then click UP or Down button to select from FL, which means 0%-99%-100% brightness, then click Back button to con rm. represents chasing effects, total 4 effects selectable from Click Up or Down button to select the menu then click Enter button to enter into the effect mode. Click Up or Down button to select effect from CA01: Fade-up (0%-100%) and fade-down (100%-0%) of the, then,,,,,, cycling chasing. CA02: Fade-up (0%-100%) of channel, then simultaneous fade-down (100%-0%) of channel and fadeup (0%-100%) of channel, so on up to last channel. Ca03: Fade-up (0%-100%) of, then,,, 4,,, cycling chasing. CA04: Fade-down (100%-0%) of, then,,, 4,,, cycling chasing. represents chasing speed. Selectable from 01-09, 01 is the slowest, 09 is the fastest. 2) For run1 DMX decoder mode: After powering on the decoder, click Up button until to get following menu on display: X DMX signal indicator : hen DMX input signal is detected, the indicator on X will display following after turns red. X Means DMX address. factory defaults setting is 001. Means DMX channels quantity. factory defaults setting is Ch24. Means Bit (8bit or 16bit). factory defaults setting is 16bit. Means output PM frequency. factory defaults setting is 1K Hz. Means output curve gamma value, factory defaults setting is ga 1.5 Means Decoding mode, factory defaults setting is dp1.1 2/8 Means the device at run1 mode (DMX decoder mode). By holding button Back Enter together at the same time over 5 seconds until the display goes off, it will restore default settings.

3 5. RGB LED xture connection diagram: RGB LED Lighting Fixtures DMX/RDM Signal DMX/RDM Signal Class 2 regulated (12~24VDC) driver DMX OUT DMX I DC1 DC2 DC3 SR-2108B-24M put Port Single Color LED xture B G R CCT LED xture B G R G B -R RGB LED Fixture B G R RGB LED Fixture B G R arning: put voltage must be identical to output voltage of the LED Fixture! IRE 6-8 MM ( ") Exposed wire should not be more than 6-8 mm long & solder tip (tinned). Do not allow ires to cross and insure all exposed wire is fully inserted into the screw terminals. Hand tighten screw terminals. DC1~DC4 Power put : Use 13~10 AG wire put Terminals : Use 16~12 AG wire 3/8

4 DMX I DMX OUT iring with Master controller: Option 1: DMX Master Controller RJ45 Splice Cable iring Connections hite/orange Data Orange Data - Brown Ground wrong - arning correct - GD Vin D- D GD DMX Data put class2 power input hite/blue VDC hite/green VDC - Make sure that wires cannot cross Make sure that wires are screwed tight and fully inserted DMX I DMX OUT DC1 DC2 DC3 XLR-3 Class 2 Low Voltage Driver * SR-2108B-24M-3 Option 2: RGB/ Strip Light / Fixture DMX Master Controller RJ45 Splice Cable iring Connections hite/orange Data Orange Data - Brown Ground wrong - arning correct - GD Vin D- D GD DMX Data put class2 power input hite/blue VDC hite/green VDC - Make sure that wires cannot cross Make sure that wires are screwed tight and fully inserted Rj45 Cable Connectivity option for DMX Data Transfer DC1 DC2 DC3 Class 2 Low Voltage Driver * SR-2108B-24M-3 RGB/ Strip Light / Fixture 4/8

5 7. DMX/RDM terminal connection options 1. XLR-3 parallel connection XLR-3 RJ45 V- V- V V XLR-3 RJ45 V- V- V V XLR-3 RJ45 V- V- V V 2. RJ45 parrallel connection XLR-3 RJ45 V- V- V V XLR-3 RJ45 V- V- V V XLR-3 RJ45 V- V- V V 8. DMX address setting: Select menu X and then click button Enter. Display will ash then click or hold button Up or Down to set DMX address, Click button Back to con rm. 9. DMX channel quantity setting: Select menu, and then click button Enter. Display will ash, then click button Up or Down to set DMX channel quantity. Click button Back to con rm. For example the DMX address is already set as 001. CH01=1 DMX address for all the output channels, which are all address 001. CH24=24 DMX addresses, -24 is address respectively. 10. PM output resolution Bit setting: Select menu and then click button Enter. Display will ash, then click button Up or Down to choose 08 or 16 bit. Click button Back to con rm. 11. put PM frequency setting: Select menu and then click button Enter. Display will ash, then click button Up or Down to choose between 00~30. Click button Back to con rm. 00=500Hz, 01=1KHz, 02=2KHz...30=30KHz. 5/8

6 12. put curve gamma value setting: Select menu and then click button Enter, Display will ash, then click or hold button Up or Down to choose between 0.1~9.9. Click button Back to con rm gamma value put brightness level <1 >1 DMX value level 13. DMX decoding mode setting: Select menu and then click button Enter. Display will ash, then click or hold button Up or Down to choose the decoding mode. Click button Back to con rm. DMX address is 001, CH01 DMX Console Slider number dp1.1 DMX channel dp2.1 micro dp2.2 dp3.1 micro The data de nitions for strobe channel are as follows: {0, 7},//unde ned {8, 65},//slow strobe-->fast strobe {66, 71},//unde ned {72, 127},//slow push fast close {128, 133},//unde ned {134, 189},//slow close fast push {190, 195},//unde ned {196, 250},//random strobe {251, 255},//unde ned The supported RDM PIDs are as follows: DISC_UIQUE_BRH DISC_MUTE DISC_U_MUTE DEVICE_IFO DMX_START_ADDRESS IDETIFY_DEVICE SOFTARE_VERSIO_LABEL DMX_PERSOALITY DMX_PERSOALITY_DESCRIPTIO SLOT_IFO SLOT_DESCRIPTIO MAUFTURER_LABEL SUPPORTED_PARAMETERS Restore to Factory Default Setting Press and hold down both Back and Enter keys until the digital display turns off, then release the keys, system will reset and the digital display will turn on again, all settings will be restored to factory default. Default Setting are as follows: DMX Address Code: a001 DMX Address Quantity: S1=0: ch24, S1=1: ch01 PM Resolution Mode: bt16 PM Frequency: pf01 Gamma: ga1.5 Decoding Mode: dp1.1 6/8

7 DMX address is 001, CH24 DMX Console Slider number dp1.1 dp2.1 dp3.2 dp3.4 dp4.3 dp5.3 dp5.4 dp6.4 dp8.6 dp9.6 DMX channel 1 &2 &2 &3&4 &2 &3 &2 &3 &2 &3&4 &2 &3&4 &2 &3&4 &2 &3&4 2 micro &3 3 4 micro &4 &4 &6 &7& micro &6 &7 &8 &10&11 &12 &5 &6 &2 &3 &5 &6 &6 &7&8 &2&3 &4 &6 &7&8 &6 &6 8 micro & micro &8 &12 3&14& 15&16 3&15 &8 &9 &5 &6 &8 &9 &10&11 &12 &8&9 &10 &2&3&4 &5&6 &8&9 & micro &10 &16 7&18& 19&20 &11 &12 &6&7 &8 &10 &11&12 14 micro 7&19 1 for 1 & micro 1&12 8 &20 &22& 23& &8&9 &11& 12 output 12 3&14& 15&16 1 for 1 for 2 1& &23 3&14 & &14& 15& micro 2 3&14 & &10&11 &12 3&14 &15&16 3 &8&9&10 &11&12 3&14&15 & micro &17 &18 &11&12 3&14& 15 output 16 7&18& 19& micro 5& for 7 & for micro 3 3 micro 6 7& &20 & &14&15 6&17& 18 9 output 20 &22& 23&24 3&14&15 &16 7&18 &19&20 7 for 8 9&20& 21&22 9 7& micro 8 9& &14&15&16 &17&18 9&20&21 & &23 & micro 6 0 &22 3 6&17&18 9&20& 21 output 24 7&18&19 &20 &22 &23&24 3& micro & micro 3& micro &20&21 &23& 24 4 &22&23 &24 4 9&20&21&22 &23& micro micro &23&24 42 micro micro micro micro 7/8

8 14. Compatible Master Color Controllers and Controllers/Receivers Master Color Controller HUEDA (L-2814DMX) HUEDA Hub (H-2818I) RGB Handheld Remote (H-2819S) Controllers/Receivers IOS app available IOS app available RF RGB Receiver (H-R009PD) *Requires HUEDA Hub (H-2818I) to use mobile app RF RGB Receiver (door) (H-R009FA()) *Requires HUEDA Hub (H-2818I) to use mobile app 24CH DMX Decoder (SR-2108B-24M-3) Easy DMX512 Decoder (H-2102B()) Federal Communications Commission (FCC) Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: 1.This device may not cause harmful interference, and 2.This device must accept any interference received, including interference that may cause undesired operation. ote: The manufactures is not responsible for any radio or tv interference caused by unauthorized modi cations to this equipment. Such modi cations will void the user's authority to operate the equipment and warranty. THREE YEAR LIMITED ARRATY LED ORLD IC. warranties this product for three year (some exceptions may apply) from the date of shipping unless otherwise noted in writing. This warranty is expressly in lieu of all other warranties expressed or implied. Under this Limited arranty, the obligation of the company is limited to replacing on a prorated basis, at its option, any component found to be defective. This Limited arranty does not apply to damage caused by buyer or alteration to the product or incorrect power supply. Factory warrantees are covered by the original manufacturer and claims must be submitted to them. Use only with LED orld s regulated class 2 power supply. LED orld c. And its providers will never be liable to you or any other person for any indirect, incidental, consequential, special, punitive or exemplary loss or damage arising from, connected with, the purchase of products, including but not limited to loss of data, business, markets, cost of labour, savings, income, profits, use, production, reputation or goodwill, anticipated or otherwise, or economic loss, under any theory of liability (whether in contract, tort, strict liability or any other theory or law or equity), regardless of any negligence or other fault or wrongdoing (including without limitation gross negligence and fundamental breach) by led world inc. Or any person for whom led world inc. Is responsible, and even if led world inc. Has been advised of the possibility of such loss or damage being incurred. If a product is defective, we will replace the product with similar or identical product or at our option a credit towards a future purchase. To make a claim under this warranty, obtain a return authorization number. 8/8