WIZ220IO / WIZ220IO-EVB User s Manual (Ver. 1.0)

Transcription

1 [ 텍스트입력 ] WIZ0IO / WIZ0IO-EVB User s Manual (Ver. 1.0) 010 WIZnet Inc. All Rights Reserved. For more information, visit our website at

2 Document History Information Revision Data Description Ver Release with WIZ0IO launching Copyright 010 WIZnet Inc. All rights reserved

3 Table of Contents 1. Introduction Main Function Specification Block Diagram WIZ0IO Base Board Configuration Tool Basic description Network Tab Serial Tab Input / Output Tab Firmware Upload Webpage Upload Use of Rom File Maker rev WIZ0IO Specification Electrical Characteristics Pin Header RJ-45 connector Board Dimensions and Pin Assignment Warranty... 0 Copyright 010 WIZnet Inc. All rights reserved

4 Tables Table 1. WIZ0IO Specification... 7 Table. WIZ0IO Base Board Specification... 7 Table 3. Electrical characteristics Table 4. RJ-45 Pin Assignment Table 5. WIZ0IO Dimension Copyright 010 WIZnet Inc. All rights reserved

5 Figures Figure 1. Block Diagram 8 Figure. WIZ0IO Base Board Layout 9 Figure 3. WIZ0IO Module Interface 9 Figure 4. LED circuit of WIZ0IO Base Board 10 Figure 5. DI Switch of the WIZ0IO Base Board 10 5 Figure 6. Power adapter polarity 10 Figure 7. Variable Resistor Circuit of the WIZ0IO Base Board 11 Figure 8. Configuration Tool 1 Figure 9. Network Tab of the Configuration Tool 14 Figure 10. Serial Tab of the Configuration Tool 15 Figure 11. Input / Output Tab of the Configuration Tool 16 Figure 1. Firmware uploading window 16 Figure 13. Complete firmware uploading window 17 Figure 14. RJ-45 PIN Assignment 18 Figure 15. WIZ0IO Module Dimension 19 Copyright 010 WIZnet Inc. All rights reserved

6 1. Introduction WIZ0IO is an embedded remote I/O module which is able to control and monitor I/O port remotely via Internet. It is possible to monitor and control I/O port by using Windows application program or the embedded Web server. There are 16 digital I/O ports and 4 analog I/O supported by WIZ0IO. Additionally, the firmware and embedded webpage can also be updated remotely through the Ethernet. WIZ0IO-EVB is the evaluation base board for users to evaluate WIZ0IO module quickly. There are 8 switches used for digital input test and 8 LEDs for digital output test, and a variable register for analog input test included in this evaluation board Main Function 6 Operates as HTTP Server using W7100, all-in-one embedded network MCU with hardwired TCP/IP stack Provides Configuration Tool Program for easy control, monitoring and configuration Supports 10/100Mbps Ethernet 8 Digital Input Ports 8 Digital Output ports Analog Input Ports with 1-bit resolution (Voltage Type) Analog Output Ports with 1-bit resolution (Voltage Type) 1 UART Output Port Data acquisition and transmitting to specified host RoHS Compliant Copyright 010 WIZnet Inc. All rights reserved

7 1.. Specification Architecture Network MCU PHY TCP/IP Stack Network Protocols Network Interface Standard 8051 compatible in W7100 Included in W7100 Hardwired TCP/IP Stack in W7100 ARP, ICMP, TCP/IP, UDP, HTTP Server, DHCP RJ-45, Auto-MDIX, Auto-Negotiation Digital Analog Input CMOS Digital Input Output CMOS Digital Output 1 UART output Baud rate : 100bps ~ 30400bps Data bit : 7bit, 8bit UART Parity : none, odd, even Stop bit : 1bit Flow control : none, RTS/CTS Input 1bit resolution. Input Range(0 ~ Vcc) Output 1bit resolution. Output Range(0 ~ 4v) 7 Power Input Voltage Power Consumption DC 5V Under 5V Environment Temperature 0 C ~ 70 C (Operation), -40 C ~ 85 C (Storage) Humidity 10 ~ 90% Table 1. WIZ0IO Specification Power Socket Inner pin Ø.0, DC Power Jack Voltage DC 5V Digital Ports Input 8-Switch Output 8-LED (Green chip-led) UART D-SUB 9PIN MALE Analog Input -Variable Resistor(10K ohm) Output None(Through Hole) I/O Switch Factory Reset Switch Table. WIZ0IO Base Board Specification Copyright 010 WIZnet Inc. All rights reserved

8 1.3. Block Diagram 8 Figure 1. Block Diagram Not only the I/O controlling and monitoring functions included in WIZ0IO, but also the I/O value transmission function is also included in it. The users can control or monitor via web browser in remote host PC, and configure the module s environment parameters and check the IO status via the provided Configuration Tool. The interface of WIZ0IO consists of analog interface and digital interface. 1 bits resolution analog I/O, 3.3V digital output and the maximum 5.5V digital input are supported by WIZ0IO. The digital I/Os are internal pulled up. The users can use Web browser or Configuration Tool to remotely control the interfaces and the UART data output can also be displayed in Web browser. Copyright 010 WIZnet Inc. All rights reserved

9 . WIZ0IO Base Board WIZ0IO module can be tested by using base board. 9 Figure. WIZ0IO Base Board Layout 1 WIZ0IO Module Connector It is an interface for WIZ0IO Module. [Caution] Observe pin position and align when mounting the module to base board. Incorrect mounting can damage the WIZ0IO module and base board, and your product warranty does not cover such damage. J1 J GND DI_0 DI_1 DI_ DI_3 GND DO_0 DO_1 DO_ DO_ GND DI_4 DI_5 DI_6 DI_7 GND DO_4 DO_5 DO_6 DO_7 5V_input 5V_input nrst_in GND P_ P_4 AI_0 AI_1 AO_0 AO_ F_RST TXD RXD GND RTS CTS GNDAA GNDAA GNDAA GNDAA CON0A /.54mm Digital I/O CON0A /.54mm Power / Analog GNDAA Figure 3. WIZ0IO Module Interface LED 8 LEDs are indicating each Digital Output ports. When the port signal is LOW, the LED light is turned on. Copyright 010 WIZnet Inc. All rights reserved

10 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V LED LEDG-SMD LED3 LEDG-SMD 1 1 LED4 LEDG-SMD LED5 LEDG-SMD 1 1 LED6 LEDG-SMD LED7 LEDG-SMD 1 1 LED8 LEDG-SMD LED9 LEDG-SMD 1 1 R8 00 R9 00 R10 00 R11 00 R1 00 R13 00 R14 00 R15 00 DO_0 DO_1 DO_ DO_3 DO_4 DO_5 DO_6 DO_7 Figure 4. LED circuit of WIZ0IO Base Board 3 Switch 8 switches are controlling each Digital Input ports. When you turn switch on, the digital port signal will be LOW. SW3 10 DI_0 DI_1 DI_ DI_3 DI_4 DI_5 DI_6 DI_7 SW DIP-8 Figure 5. DI Switch of the WIZ0IO Base Board 4 D-SUB9 This connector is for an UART. The WIZ0IO s UART port can be used for debug message or data output through the webpage. It supports RTS/CTS flow control. 5 Power The power can be controlled by using power switch after connecting the DC 5V (min 500mA) adapter. [Caution] Observe polarity and voltage when connecting the power adapter. Incorrect input polarity or voltage can damage the WIZ0IO module and base board, and your product warranty does not cover such damage. Figure 6. Power adapter polarity 6 Power Switch It controls power of WIZ0IO module and base board. 7 Factory Reset button Factory reset button can recover configuration parameter to factory default values. To reset the module s parameters to factory default, hold down the factory reset button when you turn power Copyright 010 WIZnet Inc. All rights reserved

11 switch on. 8 Variable Resistor (VR) You can control analog input value with variable resistor. The WIZ0IO s analog input is voltage type and its range is 0V to Vcc(5V). Also, its value was translated to 0~4095 as each input port has 1-bit resolution. 5V_input B 1 Y A VR1 VR R1 00 AI_0 11 5V_input VR VR B 1 Y A 3 3 GNDAA R 00 AI_1 GNDAA Figure 7. Variable Resistor Circuit of the WIZ0IO Base Board 9 Analog Output Through Hole It can be connected external device by user application. Each port outputs its value as voltage level, and the range of output voltage is 0~4V. The maximum output value is 4095 that is generate 4V level. The hole pitch is.54mm. Copyright 010 WIZnet Inc. All rights reserved

12 3. Configuration Tool The configuration tool supports below major functions. All functions of configuration tool can be performed remote area through the Ethernet. - Change module s configuration. - I/O monitoring and controlling - Firmware uploading - Webpage uploading 3.1. Basic description 1 Figure 8. Configuration Tool - FW Version: It displays firmware version. - Enable Serial Debug Mode: If this mode is checked, you can monitor the status and socket message (listen OK, connect fail etc.) through serial terminal. - Board List: If you click the SEARCH button, all the MAC address on a same subnet will be displayed. When you check the Direct IP Search and enter the specified IP address, the board list will be displayed its MAC address. Copyright 010 WIZnet Inc. All rights reserved

13 - Direct IP Search: Direct IP Search can be used for searching WIZ0IO not installed in the same subnet. If the Direct IP Search is checked, the configuration tool use the TCP instead UDP broadcast to search module. Therefore, network information of the module such as IP address, subnet mask and gateway address is required for the search. [Warning] If module does not have valid network information, Direct IP Search is not available. If the module is connected to the NAT or private network, it is not possible to connect to the module from outside. - Search: The Search function is used to search all modules existing on the same LAN. By using UDP broadcast, all modules on the same subnet will be searched. The searched module is displayed as MAC address in the Board List Setting: This function is to complete the configuration change. If you select the MAC address from the Board List, the current configuration values of the module will be displayed. Change the configuration value and click Setting button to complete the configuration. After that, the module will re-initialize with the changed configuration. - Webpage: It is possible to upload ROM Image file to the internal flash memory of WIZ0IO. For more information, refer to 3.6. Webpage Upload. - Upload: It is possible to upload new firmware file through the Ethernet. For more information, refer to 3.5. Firmware Download. - Ping: It is used to test whether the WIZ0IO module is reachable across a network from your PC with ICMP protocol. After inputting host IP address in new pop-up window, click the PING button. Then, it will be displayed its result. - Firewall: It controls your PC s firewall configuration. If board list does not display even though clicking search button, check your PC s firewall. - Exit: Close the configuration tool program. 3.. Network Tab Network Tab of the configuration tool can be set the network information and the notification parameters. The network information is for a communication through the Ethernet such as an IP address, a gateway address and a subnet mask. If the module cannot be assigned fixed information from ISP provider, you can set the DHCP option. The DHCP option can be assigned network information from DHCP server. The notification option is a function for sending the I/O values to the specified host every specified period. It is useful to acquiring data log. Copyright 010 WIZnet Inc. All rights reserved

14 14 Figure 9. Network Tab of the Configuration Tool - IP Configuration Method: You can select STATIC or DHCP. The STATIC option can be selected when your network resource can give the fixed IP address, and the DHCP option can be selected when your network has DHCP server such as a router who has DHCP server function. - Local IP Address: IP address of the WIZ0IO module. - Subnet Mask: Subnet mask of the WIZ0IO module. - Gateway address: Gateway address of the WIZ0IO module. [Warning] Be sure to input correct network information. If you input incorrect information, it can cause network collision or mal-function. - HTTP Port Number: You can change webserver s listen port number. The HTTP default port number is Notification Options Protocol: The WIZ0IO can send I/O values to the specified host. This parameter is a protocol of sending data. The TCP Server waits for the connection trial from the host, And the TCP Client tries to connect to the host s IP address and port number. At the UDP mode, the connection establishment is not defined. Just set the IP address and port number of the host and send data. - Listen Port Number: It is valid only on TCP Server mode. The WIZ0IO module will accept connection with listen port number. - Remote IP Address / Remote Port Number: It is valid on TCP Client and UDP modes. Input the target host s IP address and port number. Copyright 010 WIZnet Inc. All rights reserved

15 - Keep TCP connection: If you check this option, the WIZ0IO module keep the connection as sending keep-alive packet. If you uncheck this option, the module close the connection after sending data. - Time period to sending: It is possible to set the sending period. To disable notification option, input 0 to this parameter Serial Tab Serial tab is for the UART configuration. The UART is used to display debug message and to output the UART data through the webpage. 15 Figure 10. Serial Tab of the Configuration Tool - Speed: It supports baud rate from 100bps to 30400bps. - Data Bit: It supports 7bit or 8bit of data bit. - Parity: It supports odd, even and none option of parity. - Stop Bit: It supports only 1bit. - Flow: It supports flow control none, RTS/CTS Input / Output Tab Input/Output tab is for the I/O control and monitoring. When you click the Update I/O Status button, it will be displayed I/O parameters at that time. In the Digital parameters, a green indicator means port is asserted HIGH and a gray indicator means LOW. Each port can be set HIGH as checking checkbox in Digital Output Control and click the Update I/O Status button. The Analog I/O has range as 0 to 4095 and it has voltage type. In the Analog input status, 4095 means maximum input value that is same to 5V_Input (Vcc) value. However, analog output maximum value 4095 generates 4V. In other word, the analog output maximum value is 4V. [Warning] In the WIZ0IO Base Board, LEDs and SWITCHs are implemented ON as LOW. Copyright 010 WIZnet Inc. All rights reserved

16 16 Figure 11. Input / Output Tab of the Configuration Tool 3.5. Firmware Upload 1 Execute WIZ0IO configuration tool and click Search button. If the module is correctly connected to the network, its MAC address is displayed on the Board list. 3 Select the board at the Board list and click Upload button. [Warning] Before uploading through Ethernet, the network information should be set for correct network communication. The configuration tool send ping request automatically, and if there is no reply from board, it will display error message. 4 When the dialog box is shown, select the Binary file and click OPEN button. [Warning] Be sure to use firmware only for the WIZ0IO. 5 You can see below status window showing Processing. Figure 1. Firmware uploading window Copyright 010 WIZnet Inc. All rights reserved

17 6 If the file is uploaded, Complete firmware uploading message will be displayed. Figure 13. Complete firmware uploading window 3.6. Webpage Upload 17 1 Execute WIZ0IO configuration tool and click Search button. If the module is correctly connected to the network, its MAC address is displayed on the Board list. 3 Select the board at the Board list and click web page Upload button. [Warning] Before uploading through Ethernet, the network information should be set for correct network communication. The configuration tool send ping request automatically, and if there is no reply from board, it will display error message. 4 When the dialog box is shown, select the Flash Rom File System (*.rom) file and click OPEN button. [Warning] The Flash Rom File system should be created by usinig Rom File Maker Tool rev3.0. For the detail, refer to Use of Rom File Maker rev If the file is uploaded, Complete webpage uploading message will be displayed Use of Rom File Maker rev3.0 Rom File Maker rev3.0 is the tool for creating ROM Image which enables the webpage to be stored in the Flash memory. 1 Select the webpage by using Add Files button. [Warning] There is limitation of file number in selecting at a time. (Normally, max 15 files can be selected simultaneously). If there are more files, use Add Files button for the several times. Select Rom Image File option. If you click Make Image button, *.rom file can be created. [Warning] The limitation of the ROM image size is 0476bytes. If the file size is over 0476bytes, it does not guarantee its operation. Copyright 010 WIZnet Inc. All rights reserved

18 4. WIZ0IO Specification 4.1. Electrical Characteristics Parameters Min Typ Max Units Input Voltage (Vcc) V High Level Digital Input V Low Level Digital Input V High Level Digital Output V Low Level Digital Output V Digital Output Current 8 ma Analog Input Range Vss - Vcc V Analog Input Leakage Current.001 ±1 μa Analog Output Range 0-4 V Analog Output Short Circuit Current 15 4 ma Operation Temperature 0-70 Storage Temperature Power Consumption(@DC5V) 80 ma Table 3. Electrical characteristics Pin Header - x10pin Dual Line,.54mm Pitch, 1mm height - Lead length = 6mm - Straight Type - Gold Plating - Current Rating:1A - Insulation Resistance:500Mohm - Dielectric Withstanding Voltage:500VAC 4.3. RJ-45 connector Pin Signal 1 TX+ TX- 3 RX+ 6 RX- Figure 14. RJ-45 PIN Assignment Table 4. RJ-45 Pin Assignment Copyright 010 WIZnet Inc. All rights reserved

19 4.4. Board Dimensions and Pin Assignment 19 Figure 15. WIZ0IO Module Dimension Symbol mm A a 1.18 a 4.00 B b b b C 3.00 Table 5. WIZ0IO Dimension Copyright 010 WIZnet Inc. All rights reserved

20 5. Warranty WIZnet Co., Ltd offers the following limited warranties applicable only to the original purchaser. This offer is non-transferable. WIZnet warrants our products and its parts against defects in materials and workmanship under normal use for period of standard ONE(1) YEAR for the WIZ0IO module and labor warranty after the date of original retail purchase. During this period, WIZnet will repair or replace a defective products or part free of charge. Warranty Conditions: The warranty applies only to products distributed by WIZnet or our official distributors. 1. The warranty applies only to defects in material or workmanship as mentioned above in 7. Warranty.. The warranty applies only to defects which occur during normal use and does not extend to damage to products or parts which results from alternation, repair, modification, faulty installation or service by anyone other than someone authorized by WIZnet Inc. ; damage to products or parts caused by accident, abuse, or misuse, poor maintenance, mishandling, misapplication, or used in violation of instructions furnished by us ; damage occurring in shipment or any damage caused by an act of God, such as lightening or line surge. 0 Procedure for Obtaining Warranty Service 1. Contact an authorized distributors or dealer of WIZnet Inc. for obtaining an RMA (Return Merchandise Authorization) request form within the applicable warranty period.. Send the products to the distributors or dealers together with the completed RMA request form. All products returned for warranty must be carefully repackaged in the original packing materials. 3. Any service issue, please contact to sales@wiznet.co.kr Copyright 010 WIZnet Inc. All rights reserved