BIM-ALERT CICS AND VSE SECURITY SYSTEM INSTALLATION AND OPERATIONS GUIDE. Release 5.0 (COPYRIGHT 1998, B I MOYLE ASSOCIATES, INC.)

Transcription

1 BIM-ALERT CICS AND VSE SECURITY SYSTEM INSTALLATION AND OPERATIONS GUIDE Release 5.0 (COPYRIGHT 1998, B I MOYLE ASSOCIATES, INC.) BIM-ALERT is a proprietary product of B I Moyle Associates, Inc. It cannot be reproduced, changed, copied, or stored in any form (including, but not limited to, copies on magnetic media) without the express prior written permission of B I Moyle Associates, Inc.

2 This documentation applies to Release 5.0 of the program product BIM-ALERT. Original Printing... 05/15/98 Last Revised... 07/10/98

3 Contents Trademark Information...vii Related Publications...viii Chapter 1 Preparing to Install BIM-ALERT If You Are Running a Version of BIM-ALERT Prior to If You Are Installing BIM-ALERT/CICS and BIM-ALERT/VSE Overview of Installing BIM-ALERT Checklist for Preinstallation Steps Deciding Which Components to Install System Requirements BIM-ALERT/CICS Requirements BIM-ALERT/VSE Requirements Identifying the BIM-ALERT Residence Sublibrary Introduction Sublibrary Size Requirements Sublibrary Member Names Chapter 2 Restoring the BIM-ALERT Installation Tape Introduction Step 1: Remove Existing BIM-ALERT MSHP Entries Step 2: Create the Installation Procedure Introduction Tailoring the Installation Procedure Step 3: Restoring the Installation Tape Deferred Execution of the Generated Installation Procedure Chapter 3 Installing BIM-ALERT/VSE Introduction About This Chapter Using the Sample JCL Sharing BIM-ALERT/VSE Files in a Multiple CPU Setting Installation Procedure for Current Users Introduction Step 1: Deactivate BIM-ALERT/VSE Step 2: Catalog a New AXPPROC Procedure Step 3: Prepare Online Files for Conversion to 5.0 Format Step 4: Create the Version 5.0 Online Security Files Step 5: Create the Version 5.0 Messages File Step 6: Create the Version 5.0 Administrator Audit File Step 7: Update POWER Start JCL and BG ASI Procedure Step 8: Update CICS Table Entries Step 9: Update Your JCLLUSEX List Step 10: Verify IJSYSRS.SYSLIB Standard Label Step 11: Activate Submittal Monitors and Security Exits Step 12: Verify IJSYSRS Phases Step 13: Convert Rules Tables to 5.0 Format Step 14: Assemble the Network Submittal Table Step 15: Perform an IPL to Activate BIM-ALERT Contents iii

4 Installation Procedure for a New Installation Introduction Step 1: Verify BIM-ALERT/VSE VSAM Cluster Names Step 2: Define an Extent for Rules Assembly Work File Step 3: Catalog the AXPPROC Procedure Step 4: Define the Log Files Step 5: Define and Load the Control File Step 6: Convert BIM-ALERT/CICS Security Files Step 7: Create the Version 5.0 Online Security Files Step 8: Create the Version 5.0 Messages File Step 9: Define and Initialize the Audit File Step 10: Add LIBDEF and DLBLs to CICS Partition Startup Step 11: Update CICS Table Entries Step 12: Update Your JCLLUSEX List Step 13: Verify the Standard Label for IJSYSRS.SYSLIB Step 14: Catalog New ASI IPL and JCL Procedures Step 15: Trial IPL With SEC IPL Procedures Step 16: Catalog a New $ASIPROC Master Procedure Step 17: Activate Submittal Monitors and Security Exits Step 18: Verify IJSYSRS Phases Step 19: Perform an IPL to Activate BIM-ALERT Chapter 4 Submittal Monitors and Security Exits About This Chapter About the Submittal Monitor Facility Introduction Omitting ID Cards From Remote Jobs Installing Submittal Monitors BIM-EDIT Submittal Monitor BIM-FAQS/PCS Submittal Monitor CA-SCHEDULER Submittal Monitor CA-VOLLIE Submittal Monitor CMS Submittal Monitor CONDOR Submittal Monitor CSAR Submittal Monitor EZ/KEY Submittal Monitor GSERV Submittal Monitor ICCF Submittal Monitor I.E. Submittal Monitor ZEKE Submittal Monitor Installing Security Exits Introduction Installing a Security Exit for CA-EXPLORE for CICS-VSE Installing a Security Exit for CA-EXPLORE for VSE Installing a Member-Level Security Exit for BIM-FAQS/PCS Installing a Job-Submittal Security Exit for BIM-FAQS/PCS Installing a Security Exit for CA-FAVER for VSE Installing a Security Exit for CA-MASTERCAT for VSE Installing a Security Exit for CA-XCOM Installing a Security Exit for DITTO for VSE and DITTO/ESA Chapter 5 BIM-ALERT/VSE Operation iv Installation and Operations Guide

5 About This Chapter About the VSE Data Security Environment Introduction Running Without BIM-ALERT/VSE Active BIM-ALERT/VSE Logging Managing the Log Data Log File Merge Utility AXPL Log File Purge Enqueue Mechanism Redefining the Log File When the Log File Is Full Logger Shutdown Controlling the Logger From a Batch Partition Log File Report Program About The Log File Report Program Report Program Control Statements JCL and Control Statement Examples SECID Summary Report Program Audit File Report Program Performing VSE Maintenance with BIM-ALERT Active When Applying Maintenance Verifying Security Phases in IJSYSRS.SYSLIB Managing $JOBEXIT Phases Introduction Guidelines Determining the Status of $JOBEXIT Phases Reloading a Local POWER JOBEXIT Program Message 1U72I During IPL Chapter 6 BIM-ALERT/VSE Utility Programs AXPI9X Utility AXPU1 Utility AXPU2 and AXPU5 Utilities Introduction AXPU2 Utility AXPU5 Utility AXPU4 Utility Introduction Control Statements Syntax for Control Statements Format for Control Statements Special Character Sequences in Library Records Running AXPU4 During IPL/ASI Chapter 7 Installing BIM-ALERT/CICS Introduction Are You Installing Both BIM-ALERT/VSE and BIM-ALERT/CICS? Using the Sample JCL CICS Running in the SVA Installation for New Users of BIM-ALERT/CICS Step 1: Restore the Installation Tape Step 2: Add Required CICS Table Entries Step 3: Add Optional CICS Table Entries Contents v

6 Step 4: Create the Online Security File Step 5: Create the Messages File Step 6: Create the Administrator Audit File Step 7: Create the Violation Log File Step 8: Adjust the Size of the CSA Common Work Area Step 9: Add SET SDL Entries for MRO Control Modules Step 10: Add DLBLs for the Security Files to CICS Job Control Activating BIM-ALERT/CICS Installation for Current Users of BIM-ALERT/CICS Step 1: Restore the Installation Tape Step 2: Update Required CICS Table Entries Step 3: Update Optional CICS Table Entries Step 4: Prepare Online Files for Conversion to 5.0 Format Step 5: Create the Version 5.0 Online Security File Step 6: Create the Version 5.0 Messages File Step 7: Create the Version 5.0 Administrator Audit File Step 8: Create the Version 5.0 Violation Log File Step 9: Add SET SDL Entries for MRO Control Modules Step 10: Adjust the Size of the CSA Common Work Area Step 11: Shut Down CICS Step 12: Reassemble User Exits Step 13: Reassemble Post Sign-On Programs Step 14: Reassemble Parameter-Driven Sign-On Programs Step 15: Reassemble Custom Versions of S1S611 and S1S Step 16: Convert Field-Level Security Macros Step 17: Remove BIM-ALERT/CICS From the PLT Startup Step 18: Clear Existing BIM-ALERT/CICS Tables Implementing BIM-ALERT in an MRO Environment Running BIM-ALERT with the VSE/SP Interactive User Interface Index... Index.1 vi Installation and Operations Guide

7 Trademark Information This manual refers to the following brand or product names, registered trademarks, and trademarks which are listed according to their respective owners. Platinum Software: ZEKE Computer Associates International, Inc.: CA-SCHEDULER CA-VOLLIE CA-ALERT for VM CA-EXPLORE for CICS-VSE CA-EXPLORE for VSE CA-FAVER CA-FLEE CA-MASTERCAT CA-XCOM Phoenix Software Company: CONDOR Software Engineering of America: CSAR Dun & Bradstreet Software Services, Inc.: I.E. International Business Machines: CICS CICS/ESA CICS/VSE IBM IDCAMS MVS/ESA VM VSE/ESA VSE/POWER VSE/SP VTAM Trademark Information vii

8 Related Publications Overview This section lists the documentation that deals with BIM-ALERT/VSE and BIM- ALERT/CICS. Your BIM Account Manager can order any of these documents for you. BIM-ALERT/VSE Manuals Subject Installation Using BIM- ALERT Reports Messages Manual The BIM-ALERT Installation and Operations Guide explains how to install and maintain BIM-ALERT/VSE. The BIM-ALERT/VSE Security Administrator's Guide explains how to use BIM-ALERT/VSE to set up and maintain security. The BIM-ALERT Auditing and Report Writing Guide explains how to use the BIM-ALERT batch report writer. The BIM-ALERT Messages Guide contains explanations of all messages issued by BIM-ALERT/VSE. BIM-ALERT/CICS Manuals Subject Installation Using BIM- ALERT Reports Messages Manual The BIM-ALERT Installation and Operations Guide explains how to install BIM-ALERT/CICS. The BIM-ALERT/CICS Security Administrator's Guide explains how to use BIM-ALERT/CICS to set up and maintain security. The BIM-ALERT Auditing and Report Writing Guide explains how to use the BIM-ALERT batch report writer. The BIM-ALERT Messages Guide contains explanations of all messages issued by BIM-ALERT/CICS. viii Installation and Operations Guide

9 1 Preparing to Install BIM-ALERT This chapter lists system requirements and tasks you should perform prior to installing BIM-ALERT/VSE and BIM-ALERT/CICS. If You Are Running a Version of BIM-ALERT Prior to If You Are Installing BIM-ALERT/CICS and BIM-ALERT/VSE Overview of Installing BIM-ALERT Checklist for Preinstallation Steps Deciding Which Components to Install System Requirements BIM-ALERT/CICS Requirements BIM-ALERT/VSE Requirements Identifying the BIM-ALERT Residence Sublibrary Introduction Sublibrary Size Requirements Sublibrary Member Names

10 If You Are Running a Version of BIM-ALERT Prior to 4.7 If You Are Running a Version of BIM-ALERT Prior to 4.7 If you are currently running a version of BIM-ALERT prior to 4.7, contact BIM Technical Support. Do not attempt to use the procedures in this document to upgrade from a version of BIM-ALERT prior to Installation and Operations Guide

11 If You Are Installing BIM-ALERT/CICS and BIM-ALERT/VSE If You Are Installing BIM-ALERT/CICS and BIM- ALERT/VSE If you are installing or converting existing releases of both BIM-ALERT/CICS and BIM-ALERT/VSE, you must convert them at the same time and in the order described in this manual. That is, you must install or convert BIM-ALERT/VSE and then install or convert BIM-ALERT/CICS. Chapter1. Preparing to Install BIM-ALERT 1-3

12 Overview of Installing BIM-ALERT Overview of Installing BIM-ALERT When you install BIM-ALERT/VSE and BIM-ALERT/CICS, you will perform the following activities. In general, installation requires that these activities be completed in the sequence shown here. Step Process Described in 1 Prepare for installation. If you are a current user of BIM-ALERT/VSE or BIM-ALERT/CICS, back up your online security files and, in some cases, your messages files before proceeding with the rest of the installation. Refer to the Checklist for Preinstallation Steps on page 1-5 for lists of the files you should back up. 2 Obtain jobstreams from the installation tape. Jobstreams from the installation tape are read into the VSE/POWER reader queue. 3 Tailor the installation procedure. This process executes one of the jobstreams read into the POWER reader queue from the tape. When you run this jobstream, you answer questions on the VSE system console to tailor the installation procedure. You choose if you want to install both BIM-ALERT/VSE and BIM-ALERT/CICS, and the name of the VSE sublibrary you want to use. 4 Execute the installation procedure. This process restores the contents of one or more of the sublibraries from the installation tape into the sublibrary (or sublibraries) you chose in step 3. 5 Tailor BIM-ALERT files and tables, and modify your VSE procedures, jobstreams, and tables. If you are currently using BIM-ALERT/VSE or BIM-ALERT/CICS, you must convert several files and tables to the 5.0 format by executing jobstreams and programs that were restored into your installation sublibrary. All users must modify certain cataloged VSE procedures, jobstreams, and tables to include information required to use BIM-ALERT/VSE or BIM-ALERT/CICS. Chapter 1, "Preparing to Install BIM-ALERT" Chapter 2, "Restoring the BIM-ALERT Installation Tape" Chapter 2, "Restoring the BIM-ALERT Installation Tape" Chapter 2, "Restoring the BIM-ALERT Installation Tape" BIM-ALERT/VSE: Chapter 3, "Installing BIM-ALERT/VSE" Chapter 4, "BIM- ALERT/VSE Submittal Monitors and Security and Security Exits" BIM-ALERT/CICS: Chapter 7, "Installing BIM-ALERT/CICS" 1-4 Installation and Operations Guide

13 Checklist for Preinstallation Steps Checklist for Preinstallation Steps Use the following checklist to keep track of the preinstallation steps you've completed. ( ) If you are currently running BIM-ALERT/VSE or BIM-ALERT/CICS make back up copies of your online rules, user profile, and messages files as follows: If you are currently using BIM-ALERT/VSE, back up the following file: ( ) ALERTXP. ( ) AXPCTL. If you are currently using BIM-ALERT/CICS, back up the following files: ( ) S1SCTY. ( ) S1SMS##. It is necessary to back up S1SMS## only if you have created customized messages. ( ) Review compatibility issues If you are currently running any version of BIM-ALERT/VSE prior to 5.0, review the compatibility issues discussed in the BIM-ALERT/VSE Security Administrator's Guide. Consult with the security administrator and decide whether any of these issues require additional preparation before installing version 5.0. ( ) Decide which of the following components of the BIM-ALERT installation tape you want to install: ( ) BIM-ALERT/VSE - Batch security for the VSE environment ( ) BIM-ALERT/CICS - Online security for the CICS environment ( ) Check system requirements. ( ) Identify the main residence sublibrary in which to install BIM-ALERT/VSE and BIM- ALERT/CICS. Main residence sublibrary for both components: ( ) If you require both versions of BIM-ALERT/CICS the one for CICS version 2.2 or 2.3 and the one for CICS version 2.1 or 1.7 identify a second sublibrary for the second version of BIM-ALERT/CICS. Second residence sublibrary for BIM-ALERT/CICS: If you require only one version of BIM-ALERT/CICS either the one for CICS version 2.2 and 2.3 or the one for CICS version 2.1 and 1.7 you do not need the second residence sublibrary. Your BIM-ALERT/CICS will be restored to the main residence sublibrary along with BIM-ALERT/VSE. Chapter1. Preparing to Install BIM-ALERT 1-5

14 Deciding Which Components to Install Deciding Which Components to Install The BIM-ALERT installation tape contains two main components: BIM-ALERT/VSE - Batch security for the VSE environment BIM-ALERT/CICS - Online security for the CICS environment You can install either or both of these components. Installing both allows you to enable either of them at your convenience. The extra overhead involved in installing both components at once is minimal. 1-6 Installation and Operations Guide

15 System Requirements BIM-ALERT/CICS Requirements System Requirements BIM-ALERT/CICS Requirements Software Requirements In order to properly install BIM-ALERT/CICS, your software must possess the following characteristics: CICS/VS release 1.7 or higher VSAM release 1.2 or higher SORT Hardware Requirements In order to properly install BIM-ALERT/CICS, your hardware must possess the following characteristics: CRT or compatible devices 3287 printer (only if you use real-time audit to print) Disk space for four VSAM files GETVIS Requirements The BIM-ALERT/CICS GETVIS requirements vary greatly depending on the following: Size of your network Number of resources to be protected Amount of security activated at CICS initialization In order to help you determine your system requirements, BIM-ALERT/CICS displays messages during initialization showing the amount of storage allocated for BIM-ALERT/CICS use. The storage that is allocated can come from either the partition GETVIS or the system GETVIS areas. You determine which GETVIS area will be used by specifying an appropriate value for the CONTROL SUFFIX field of the UPAR screen, as follows: If you specify a zero, the storage comes from the partition area. If you specify a number between one and nine, the storage comes from system GETVIS and is shared by all MRO partitions using the same BIM- ALERT/CICS security file. BIM-ALERT will use storage above the 16M line where possible. (continued) Chapter1. Preparing to Install BIM-ALERT 1-7

16 BIM-ALERT/CICS Requirements System Requirements The following two tables show how to estimate how much GETVIS you need. Use the following table to estimate table space. GETVIS Required for Internal Tables BYTES SYSTEM OPTIONS TERMINAL TABLE (optional) 184 bytes fixed + variable number (tran/8)+1 (prog/8)+1 (file/4)+1 (maps/8)+1 (flds/8)+1 + user area 53 bytes... OPERATOR TABLE 128 bytes fixed + variable number (one entry for each (tran/8)+1 secured terminal) (prog/8)+1 (file/4)+1 (maps/8)+1 (flds/8)+1... TRANSACTION TABLE PROGRAM TABLE FILE TABLE MAP TABLE FLD TABLE TASK WORKAREA TABLE 17 X (# secured trans + 10) X (# secured progs + 10) X (# secured files + 10) X (# secured maps + 10) X (# secured flds + 10) X (value of MAXTASKS parm)... The size of the TASK WORKAREA TABLE is calculated by multiplying the value of your MAXTASKS startup parameter by Issue the transaction CEMT INQ SYS to determine the current MAXTASKS value. GETVIS Required for Modules Loaded by BIM-ALERT/CICS SYSTEM MONITORS: BYTES S1S110 Program monitor S1S120 File monitor S1S130 Map monitor S1S131 HLPI fastpath map monitor (CICS/VS 1.6 and above) S1S180 Field security (files) S1S181 Field security (maps) S1SFCMON Field security SYSTEM SUPPLIED EXITS (optional) (This figure may change if any user-written exits are used.) (continued) 1-8 Installation and Operations Guide

17 System Requirements BIM-ALERT/CICS Requirements Example The following table illustrates the calculation of the GETVIS requirements for a network consisting of 150 operators using 100 secured terminals, 100 secured transactions, 100 secured programs, 50 secured files, and 0 secured maps. No user exits are specified. MAXTASKS is defined as 30. BYTES SYSTEM OPTIONS TERMINAL TABLE ( ) x OPERATOR TABLE ( ) x TRANSACTION TABLE 17 X ( ) PROGRAM TABLE 21 X ( ) FILE TABLE 22 X ( ) MAP TABLE 116 X FLD TABLE 100 X TASK WORKAREA TABLE 1184 X * NOTE: The number of entries in the operator table is determined by the number of secured terminals that require operator sign-on, not the number of operators defined to BIM-ALERT/CICS on the S1SCTY file. This is true since you can have only one operator on a terminal at a time. PROGRAM MONITOR FILE MONITOR MAP MONITOR... 0 FLD MONITORS... 0 =============================================================================== TOTAL Chapter1. Preparing to Install BIM-ALERT 1-9

18 BIM-ALERT/VSE Requirements System Requirements BIM-ALERT/VSE Requirements Introduction Before beginning the installation steps for BIM-ALERT/VSE, you must carry out the following required steps to make sure your operating system and SVA meet the specified requirements. Operating System Requirements The following operating system requirements apply to BIM-ALERT/VSE: BIM-ALERT/VSE version 5.0 runs on all versions of VSE/SP2, VSE/SP3, VSE/SP4, and VSE/ESA 1.2 or above. The logging facility requires VSAM. The install jobstream catalogs three members into IJSYSRS.SYSLIB. These members are also copied into PRD2.SAVE and require a total of 39 blocks in each sublibrary. You must have enough free space in IJSYSRS.SYSLIB to catalog new versions of your ASI IPL procedure and your ASI JCL procedures. Use the LIBR LD command to determine the sizes of these members. The SORT program is required for the BIM-ALERT/VSE report programs. WARNING! If you have altered or recataloged your $SYSOPEN program, be aware that during installation, BIM-ALERT replaces the existing $SYSOPEN phase in IJSYSRS.SYSLIB with a BIM-ALERT program. The previous $SYSOPEN phase is retained under the name AXP$OPEN.PHASE. BIM-ALERT passes control to this phase after executing the BIM-ALERT program. See page 1-12 for a complete description of this process. Additionally, be aware that if you are installing version 5.0 of BIM-ALERT/VSE on a system that shares IJSYSRS with other systems that will continue to run earlier versions of BIM-ALERT/VSE, you must take additional steps at the time you copy and rename $SYSOPEN to ensure that all versions of BIM-ALERT run correctly. Refer to page 2-17 for more information. Partition GETVIS for the Logger The logger requires approximately 80K of partition GETVIS in the partition where it executes (usually thevse/power partition) Installation and Operations Guide

19 System Requirements BIM-ALERT/VSE Requirements SVA Requirements SVA requirements are shown in the following table. SVA Requirements SDL Entries SVA Resident Phases... 25K System GETVIS Area... 40K (25K fixed and 15K variable) The logger uses system GETVIS space for temporary buffers. During periods of very high logging activity, the amount used may be significant. Under normal circumstances, the amount does not exceed 4K. If you are running VSE/ESA version 1.3 or above, this amount is obtained from above the 16M line. You can determine the amount of SVA free space you currently have by running a job step similar to the following: // EXEC LIBR,SIZE=200K LD SDL /* /& Before you IPL with BIM-ALERT/VSE, be sure you have the required Number of free entries SVA space System GETVIS space Remember that you must always have adequate free space for reloading SVA resident phases as part of your day-to-day operations. And remember that many of the system components acquire and release system GETVIS space dynamically. This requirement may not be reflected in the USED statistics shown by a single LIBR display. Run the LIBR display several times while various other types of job are running to get an estimate of how much free space you have. The amount shown for system GETVIS includes a small amount (2K) for a rules table. If you are running VSE/ESA version 1.3 or above, this amount is obtained from the 31-bit area. As larger tables are generated, this system GETVIS requirement will increase. Consult with the security administrator to determine anticipated rules table requirements. The size of a specific rules table may be determined from the final page of the rules assembly listing. The total amount of system GETVIS required to start BIM-ALERT with a specific rules table (not including any amounts for SVA resident phases) is displayed by the start-up utility AXPI1. Chapter1. Preparing to Install BIM-ALERT 1-11

20 BIM-ALERT/VSE Requirements System Requirements Phases Automatically Loaded into the SVA For Versions of VSE Prior to VSE/ESA 1.2 If you are running a version of VSE prior to VSE/ESA 1.2, the BIM-ALERT/VSE start-up program AXPI1 automatically adds required SDL entries and loads any required phases into the SVA. For VSE/ESA 1.2, 1.3, and Above If you are running VSE/ESA version 1.2, 1.3 or above, AXPI1 automatically adds required SDL entries and loads any required phases into the SVA, except for the $JOBEXIT phases, which you must load into the SVA before activating BIM- ALERT. BIM-ALERT Replaces $SYSOPEN During Installation The VSE operating system provides a standard IPL exit facility. During IPL, the operating system passes control to whatever program is resident in IJSYSRS.SYSLIB under the name $SYSOPEN. The operating system supplies a skeleton $SYSOPEN program that does nothing but immediately return to the operating system. If an installation wants to perform IPL exit processing, they put their program in IJSYSRS.SYSLIB under the name $SYSOPEN, replacing the skeleton program supplied by the operating system. BIM-ALERT's installation procedure renames the existing $SYSOPEN program AXP$OPEN and copies a BIM-ALERT program into IJSYSRS.SYSLIB under the name $SYSOPEN. After BIM-ALERT is installed, the operating system passes control to BIM-ALERT's $SYSOPEN program during IPL, and BIM-ALERT's program passes control to AXP$OPEN. WARNING! The BIM-ALERT installation process makes copies of $SYSOPEN and AXP$OPEN in sublibrary PRD2.SAVE. It is critical that you retain these programs in PRD2.SAVE so that they will be restored later when you apply VSE system maintenance. If the BIM-ALERT $SYSOPEN program is removed from IJSYSRS, BIM-ALERT will not activate. If You Have Your Own $SYSOPEN If you replaced the skeleton $SYSOPEN program with your own program, change your procedures for modifying and recataloging your program as follows: Change your procedure to use the name AXP$OPEN.PHASE instead of $SYSOPEN.PHASE. This will avoid eliminating the BIM-ALERT program when you recatalog yours. Change your procedure so that it catalogs your program into PRD2.SAVE first and then copies it into IJSYSRS.SYSLIB Installation and Operations Guide

21 Identifying the BIM-ALERT Residence Sublibrary Introduction Identifying the BIM-ALERT Residence Sublibrary Introduction Definition Before you can install BIM-ALERT, you must either create a sublibrary or select an existing sublibrary to serve as the residence sublibrary. The residence sublibrary is the sublibrary in which BIM-ALERT phases will reside. About the Residence Sublibrary The residence sublibrary can be any sublibrary except IJSYSRS.SYSLIB. The label information for the residence sublibrary should be in system standard labels. Install All BIM- ALERT Products in the Same Sublibrary Since all BIM-ALERT products share certain important features, they must be installed in the same sublibrary. These components must also be of the same version. Installing components in different sublibraries or installing components of different versions causes initialization problems. If you install both the CICS 1.7/2.1 and 2.2/2.3 versions of BIM-ALERT/CICS, the residence sublibrary for the CICS 1.7/2.1 version must be different from the CICS 2.2/2.3 version. If You Are Currently Running BIM-ALERT If you are currently running BIM-ALERT, you should install the new version of BIM-ALERT into a sublibrary other than your current BIM-ALERT residence sublibrary. If you elect to install the new version of BIM-ALERT into your current BIM- ALERT residence sublibrary, you should back it up first. Chapter1. Preparing to Install BIM-ALERT 1-13

22 Sublibrary Size Requirements Identifying the BIM-ALERT Residence Sublibrary Sublibrary Size Requirements The approximate number of library blocks required for installing the BIM-ALERT component modules is as follows: BIM-ALERT/VSE BIM-ALERT/CICS Common utilities 2400 library blocks 1900 library blocks 1300 library blocks Sublibrary Member Names BIM-ALERT Member Names The following member names are restored during the installation process. You must ensure that none of these names duplicates any member names already existing in the residence sublibrary. Members of type PHASE whose names start with the characters S1S, S1A, S1B, S1M, S1U, or ALRT Members of type A whose names start with the characters ALRT, ALERT, COMM or S1 Members of type C whose names start with the characters S1 Members of type PHASE whose names start with the characters AXP Members of type PHASE whose names start with the characters A1M Members of type A whose names are AXPFCT, AXPPCT, and AXPPPT Members of type J whose names start with the characters AXP, ALRT, and COM Member AXPPROC.MODEL Members of type Z 1-14 Installation and Operations Guide

23 2 Restoring the BIM-ALERT Installation Tape This chapter explains how to restore the BIM-ALERT installation tape. Introduction Step 1: Remove Existing BIM-ALERT MSHP Entries Step 2: Create the Installation Procedure Introduction Tailoring the Installation Procedure Step 3: Restoring the Installation Tape Deferred Execution of the Generated Installation Procedure

24 Introduction Introduction About This Chapter This chapter explains how to restore the BIM-ALERT installation tape. Restoring the installation tape consists of the following steps: Step Action 1 If you have installed previous versions of BIM-ALERT, remove their entries from the MSHP history file. 2 Create the installation procedure. 3 Run the installation procedure to restore the installation tape. Each of these steps is discussed in detail in the following sections. Contents of the BIM-ALERT Installation Tape The BIM-ALERT installation tape contains the following files: File # Contents 1 The following VSE/POWER jobs: IALERT1 Generates the installation procedure IALERT3 Used if you defer executing the generated procedure 2-4 MSHP/LIBR backups of the BIM-ALERT common programs for CICS 2.2/ MSHP/LIBR backups of the BIM-ALERT common programs for CICS 1.7/ MSHP/LIBR backups of BIM-ALERT/CICS for CICS 1.7/ MSHP/LIBR backups of BIM-ALERT/CICS for CICS 2.2/ MSHP/LIBR backups of BIM-ALERT/VSE 2-2 Installation and Operations Guide

25 Step 1: Remove Existing BIM-ALERT MSHP Entries Step 1: Remove Existing BIM-ALERT MSHP Entries Do You Need to Take This Step? You should remove BIM-ALERT products from your MSHP history file prior to restoring version 5.0 from the tape if either of the following apply: If you are installing BIM-ALERT into the same sublibrary as a previous release. If you previously installed any of the following versions of BIM-ALERT/VSE or BIM-ALERT/CICS: BIM-ALERT/VSE version 4.0x BIM-ALERT/CICS version 3.5x BIM-ALERT/CICS version 4.5x Removing the prior version enables you to apply MSHP CORRECTs to version 5.0x. If neither of the above applies, you can proceed to step 2 on page 2-6. Sample REMOVE Jobstream Use JCL similar to the following to remove BIM-ALERT entries from the MSHP history file. Substitute an appropriate BIM-ALERT product number and component number for prodnumber and compnumber, as listed in the next section. // EXEC MSHP,SIZE=700K REMOVE prodnumber REMOVE compnumber /* Chapter 2. Restoring the BIM-ALERT Installation Tape 2-3

26 Step 1: Remove Existing BIM-ALERT MSHP Entries MSHP Product and Component Names for BIM-ALERT Versions The following table shows the MSHP product names and component names for the various versions of BIM-ALERT: BIM-ALERT/VSE ALERT Version MSHP Product Number MSHP Component Number 4.72 ALT ALT ALT ALT ALT ALT ALT ALT ALT ALT ALT ALT ALT ALT ALT ALT BIM-ALERT/CICS ALERT Version CICS Version MSHP Product Number MSHP Component Number ALC ALC ALC ALC ALC ALC ALC ALC or 2.1 ALC ALC or 2.3 ALC ALC or 2.1 ALC ALC or 2.3 ALC ALC or 2.1 ALC ALC or 2.3 ALC ALC or 2.1 ALC ALC or 2.3 ALC ALC or 2.1 ALC ALC or 2.3 ALC ALC or 2.1 ALC ALC or 2.3 ALC ALC (continued) 2-4 Installation and Operations Guide

27 Step 1: Remove Existing BIM-ALERT MSHP Entries Common Component ALERT Version CICS Version MSHP Product Number MSHP Component Number 4.72 ACV ACV ACV ACV or 2.1 ACV ACV or 2.3 ACV ACV or 2.1 ACV ACV or 2.3 ACV ACV or 2.1 ACV ACV or 2.3 ACV ACV or 2.1 ACV ACV or 2.3 ACV ACV or 2.1 ACV ACV or 2.3 ACV ACV or 2.1 ACV ACV or 2.3 ACV ACV Chapter 2. Restoring the BIM-ALERT Installation Tape 2-5

28 Introduction Step 2: Create the Installation Procedure Step 2: Create the Installation Procedure Introduction Introduction In this step, you run the IALERT1 jobstream. IALERT1 creates an installation procedure, DCMINST, which you execute to restore the contents of the installation tape. When you run IALERT1, you answer questions on the VSE system console that tailor the installation procedure to your needs. Procedure To run the IALERT1 job, take the following steps: Step 2a 2b Action Mount the BIM-ALERT installation tape. Issue the following VSE/POWER command to read the IALERT1 jobstream from the tape into the VSE/POWER reader queue. Replace cuu with the address of the tape drive on which the installation tape is mounted: S RDR,cuu After you issue this command, the jobstreams from the tape (IALERT1 and IALERT3) will be in the VSE/POWER reader with a disposition of L. 2c Issue the following command to run the IALERT1 job: R RDR,IALERT1 2d As the questions appear on your VSE system console, answer them as explained in the following sections. 2-6 Installation and Operations Guide

29 Step 2: Create the Installation Procedure Tailoring the Installation Procedure Tailoring the Installation Procedure Introduction This section explains how to tailor the installation procedure for your site by answering the questions posed by the IALERT1 job. If You Are Running CICS Version 1.7 If you are running CICS version 1.7, follow the directions for CICS version 2.1. If You Are Running CICS Version 2.2 If you are running CICS version 2.2, follow the directions for CICS version 2.3. Question 1: What Is the Name of the BIM-ALERT Residence Sublibrary? Question You are first asked to name the sublibrary that will serve as the BIM-ALERT residence sublibrary. Refer to Chapter 1, "Preparing to Install BIM-ALERT", for information on residence sublibrary requirements. BIM-ALERT/VSE AND BIM-ALERT/CICS BIM-ALERT/VSE - BATCH SECURITY FOR THE VSE ENVIRONMENT BIM-ALERT/CICS - ONLINE SECURITY FOR THE CICS/VS ENVIRONMENT SPECIFYING THE BIM-ALERT RESIDENCE SUBLIBRARY 0 SETPARM LIB='LIB.SUBLIB' AT THE PAUSE, YOU WILL BE REQUIRED TO ENTER A SETPARM FOR THE RESIDENCE SUBLIBRARY. ALL BIM-ALERT COMPONENTS IN- STALLED AS PART OF THIS PROCEDURE WILL BE CATALOGED INTO THIS RESIDENCE SUBLIBRARY UNLESS YOU INSTALL BOTH THE CICS 2.1 AND CICS 2.3 VERSIONS OF BIM-ALERT/CICS (SEE BELOW). IN THAT CASE, THE BIM-ALERT/CICS FOR CICS 2.3 WILL BE CATALOGED INTO THE RESIDENCE SUBLIBRARY SPECIFIED AT THE PAUSE, AND THE CICS 2.1 VERSION OF BIM-ALERT/CICS WILL BE CATALOGED INTO THE SUBLIBRARY YOU WILL BE ASKED TO SPECIFY LATER. TWO VERSIONS OF BIM-ALERT/CICS ARE INCLUDED ON THIS INSTALL TAPE, ONE WHICH RUNS WITH CICS 2.1 AND 1.7, AND ONE WHICH RUNS WITH CICS 2.3. IF YOU NEED TO INSTALL BOTH, YOU WILL BE ASKED TO SPECIFY A SEPARATE RESIDENCE SUBLIBRARY FOR THE BIM-ALERT/CICS WHICH RUNS ON A CICS 2.1 SYSTEM LATER IN THIS PROCEDURE. (continued) Chapter 2. Restoring the BIM-ALERT Installation Tape 2-7

30 Tailoring the Installation Procedure Step 2: Create the Installation Procedure Your Response For example, if SAALRT.PROD is to be your residence sublibrary, enter // SETPARM LIB='SAALRT.PROD' Message Displayed When you enter the name of your residence sublibrary and press ENTER, the following message is displayed: YOU ARE NOW IN THE BIM-ALERT INSTALL GENERATION PROGRAM. THIS PROGRAM WILL PROMPT YOU FOR INFORMATION ABOUT WHAT YOU WANT TO INSTALL AND HOW. THIS PROGRAM BUILDS AN INSTALL PROC BASED UPON THE ANSWERS YOU SUPPLY TO THESE PROMPTS. AFTER THE PROC HAS BEEN BUILT, YOU CAN EXECUTE IT WHEN YOU ARE READY TO PERFORM THE INSTALL. 2-8 Installation and Operations Guide

31 Step 2: Create the Installation Procedure Tailoring the Installation Procedure Question 2: What Is the Tape Drive's Address? Question You are next asked to enter the CUU of the tape drive on which the BIM-ALERT installation tape is mounted, as follows: ENTER TAPE DRIVE CUU FOR INSTALL. (E.G. 280) Your Response Enter the same address you used in step 2b on page 2-6. Question 3: Are the Residence Sublibrary Name and Tape Drive Address Correct? Question Next, you are asked to confirm that the residence sublibrary name and tape drive address are correct, as follows: DO YOU WISH TO INSTALL INTO SUBLIBRARY xxxx.xxxx FROM cuu? ENTER YES OR CANCEL. Your Response Enter YES if the residence sublibrary and tape drive indicated are correct. If either is incorrect, enter CANCEL. If you enter CANCEL, the job terminates, and you must begin again by releasing IALERT1 (step 2c on page 2-6). Question 4: Do You Want to Use MSHP or LIBR to Restore the Tape? Question You are next asked if you want to use the MSHP or the LIBR IBM utility program to restore the tape: DO YOU WISH TO INSTALL USING MSHP OR LIBR? ENTER MSHP OR LIBR. Your Response Enter either MSHP or LIBR. It is recommended that you use MSHP. If you enter MSHP in response to the preceding prompt, proceed to question 6. If you enter LIBR in response to the preceding prompt, proceed to question 5. Chapter 2. Restoring the BIM-ALERT Installation Tape 2-9

32 Tailoring the Installation Procedure Step 2: Create the Installation Procedure Question 5: Do You Want to Archive the BIM-ALERT Components with MSHP? Question Next, you are asked if you want to archive the BIM-ALERT components with MSHP: DO YOU WISH TO ARCHIVE THE BIM-ALERT COMPONENTS WITH MSHP AFTER THE LIBR INSTALL? ENTER YES OR NO. Your Response If you want to have the BIM-ALERT products archived with MSHP after the LIBR install, enter YES. It is recommended that you archive the BIM-ALERT components so that fixes can be applied using MSHP CORRECT. Otherwise, enter NO. Question 6: Do You Want to Install Both BIM-ALERT/VSE and BIM-ALERT/CICS? Question You are next asked whether you want to install both BIM-ALERT/VSE and BIM- ALERT/CICS: DO YOU WISH TO INSTALL FULL BIM-ALERT SYSTEM --BIM-ALERT/VSE AND BIM-ALERT/CICS? ENTER YES OR NO. Your Response If you want to install both BIM-ALERT/VSE and BIM-ALERT/CICS, enter YES and proceed to question 9. Otherwise, enter NO and proceed to question 7. Question 7: Do You Want to Install BIM-ALERT/CICS? Question Next, you are asked if you want to install BIM-ALERT/CICS: DO YOU WISH TO INSTALL BIM-ALERT/CICS? ENTER YES OR NO. (continued) 2-10 Installation and Operations Guide

33 Step 2: Create the Installation Procedure Tailoring the Installation Procedure Your Response If you want to install BIM-ALERT/CICS, enter YES and proceed to question 9. Otherwise, enter NO and proceed to question 8. Question 8: Do You Want to Install BIM-ALERT/VSE? Question Next, you are asked if you want to install BIM-ALERT/VSE: DO YOU WISH TO INSTALL BIM-ALERT/VSE? ENTER YES OR CANCEL. Your Response If you want to install BIM-ALERT/VSE, enter YES. This completes the information necessary to generate the installation procedure. Proceed to step 3 on page Otherwise, enter CANCEL. The installation procedure is not generated because your answers indicate that you do not want to install any of the BIM-ALERT components. You can restart generation of the installation procedure by again releasing job IALERT1 from the VSE/POWER reader queue (step 2c on page 2-6). Question 9: Do You Need to Install Both the CICS 1.7/2.1 and the CICS 2.2/2.3 Versions of BIM-ALERT/CICS? Question Next you are asked whether you need to install both the CICS 1.7/2.1 and the CICS 2.2/2.3 versions of BIM-ALERT/CICS: DO YOU NEED TO INSTALL BOTH BIM-ALERT/CICS VERSIONS --- BIM-ALERT/CICS FOR CICS 2.1 AND CICS 2.3? ENTER YES OR NO Your Response If you need to install both versions of BIM-ALERT/CICS (the one for CICS 1.7/2.1 and the one for CICS 2.2/2.3), enter YES and then proceed to question 11. Otherwise, enter NO and proceed to question 10. Chapter 2. Restoring the BIM-ALERT Installation Tape 2-11

34 Tailoring the Installation Procedure Step 2: Create the Installation Procedure Question 10: Which Version of BIM-ALERT/CICS Do You Want? Question Next you are asked which version of BIM-ALERT/CICS you want to install, the version for CICS 1.7/2.1 or the version for CICS 2.2/2.3: CHOOSE EITHER THE BIM-ALERT/CICS VERSION FOR CICS 2.1 OR CICS 2.3. ENTER 21 OR 23 Your Response If you want to install the version of BIM-ALERT/CICS for CICS 1.7/2.1, enter 21 to the following prompt. Enter the number as 21 (without the period). If you want to install the version of BIM-ALERT/CICS for CICS 2.2/2.3, enter 23. Enter the number as 23 (without the period). After you enter your response to the preceding prompt, proceed to step 3 on page 2-16 to execute the generated installation procedure. Question 11: What Is the Name of the Sublibrary for the CICS 1.7/2.1 Version of BIM- ALERT/CICS? Question The next prompt asks for the name of the sublibrary where you want to install the CICS 1.7/2.1 version of BIM-ALERT/CICS: PLEASE SPECIFY SUBLIBRARY FOR CICS 2.1 VERSION **** WARNING WARNING WARNING **** YOU HAVE CHOSEN TO INSTALL BOTH VERSIONS OF BIM-ALERT/CICS. THE BIM-ALERT/CICS WHICH EXECUTES IN THE CICS 2.3 ENVIRONMENT WILL BE INSTALLED INTO THE BIM-ALERT RESIDENCE SUBLIBRARY YOU CHOSE VIA THE SETPARM AT THE BEGINNING OF THIS PROCEDURE. YOU MUST CHOOSE A DIFFERENT SUBLIBRARY IN WHICH TO INSTALL THE BIM-ALERT/CICS WHICH EXECUTES IN THE CICS 2.1 ENVIRONMENT. IF YOU CHOOSE THE SAME SUBLIBRARY, UNPREDICTABLE RESULTS WILL OCCUR WHEN YOU INITIALIZE BIM-ALERT/CICS. **** WARNING WARNING WARNING **** ENTER LIBRARY.SUBLIBRARY (continued) 2-12 Installation and Operations Guide

35 Step 2: Create the Installation Procedure Tailoring the Installation Procedure Your Response Enter the name of the sublibrary for the CICS 1.7/2.1 version of BIM-ALERT/CICS. This sublibrary must be different from the one you specified for the BIM-ALERT residence sublibrary. (The version of BIM-ALERT/CICS for CICS 2.2/2.3 will be installed in the BIM-ALERT residence sublibrary along with BIM-ALERT/VSE.) Question 12: Are the Sublibraries for BIM-ALERT/CICS Correct? Question The next prompt asks whether the sublibraries for BIM-ALERT/CICS are correct: YOU HAVE ELECTED TO INSTALL BOTH VERSIONS OF BIM-ALERT/CICS FROM THE TAPE. THE CICS 2.1 VERSION OF BIM-ALERT/CICS WILL BE INSTALLED IN library.sublibrary THE CICS 2.3 VERSION OF BIM-ALERT/CICS WILL BE INSTALLED IN library.sublibrary IS THIS CORRECT? ENTER YES OR NO Your Response If the sublibraries shown are correct, enter YES. Remember that the sublibrary for 1.7/2.1 must not be the same as the one for 2.2/2.3. Then proceed to step 3 on page 2-16 to execute the generated installation procedure. If the name of the CICS 1.7/2.1 sublibrary shown is not correct, enter NO. If you enter NO, you are asked to re-specify and then verify the sublibrary for the CICS 1.7/2.1 version of BIM-ALERT/CICS. Chapter 2. Restoring the BIM-ALERT Installation Tape 2-13

36 Tailoring the Installation Procedure Step 2: Create the Installation Procedure Question 13: What Is the Name of the Sublibrary for the CICS 1.7/2.1 Version of BIM- ALERT/CICS? Question The following prompt asks for the name of the sublibrary where you want to install the CICS 1.7/2.1 version of BIM-ALERT/CICS: PLEASE RESPECIFY THE NAME OF THE SUBLIBRARY IN WHICH THE VERSION OF BIM-ALERT/CICS WHICH SUPPORTS CICS 2.1 IS TO BE INSTALLED. ENTER LIBRARY.SUBLIBRARY Your Response Enter the name of the sublibrary where you want to install the CICS 1.7/2.1 version of BIM-ALERT/CICS. Question 14: Is the Name of the Sublibrary for the CICS 1.7/2.1 Version of BIM-ALERT/CICS Correct? Question The following prompt asks you to verify that the name of the sublibrary for the CICS 1.7/2.1 version of BIM-ALERT/CICS is correct: THE CICS 2.1 VERSION OF BIM-ALERT/CICS WILL BE INSTALLED IN library.sublibrary IS THIS CORRECT? ENTER YES OR CANCEL Your Response If the correct sublibrary is shown, enter YES. Otherwise, enter CANCEL. If the Same Sublibrary is Specified for Both Versions of BIM-ALERT/CICS During the execution of the generated installation procedure, the names of the sublibraries for the two versions of BIM-ALERT/CICS will be compared. If they are the same, the warning shown in the following figure is displayed, and the installation procedure is canceled. If that happens, restart generation of the installation procedure by releasing job IALERT1 from the VSE/POWER reader queue (step 2c on page 2-6). **** WARNING WARNING WARNING **** YOU HAVE SELECTED THE SAME SUBLIBRARY FOR BOTH THE CICS 2.1 AND CICS 2.3 VERSIONS OF BIM-ALERT FOR CICS. YOU MUST RERUN IALERT1 AND SPECIFY A DIFFERENT SUBLIBRARY FOR THE CICS 2.1 VERSION OF BIM-ALERT/CICS. **** WARNING WARNING WARNING **** 2-14 Installation and Operations Guide

37 Step 2: Create the Installation Procedure Tailoring the Installation Procedure Confirmation that the Installation Procedure Has Been Generated When your answers to the IALERT1 questions provide enough information to customize the installation procedure for your requirements, you receive the following message: INSTALL PROCEDURE GENERATED... After you receive this message, proceed to step 3 on page Cancellation of the Installation Generation Process Why Generation of the Installation Process Is Cancelled Generation of the installation procedure is canceled when you request it by responding CANCEL to one of the questions. Message Displayed If the installation procedure was not generated, the following message is displayed: INSTALL CANCELLED To Restart Generation of the Installation Process You can restart generation of the installation process by releasing job IALERT1 from the VSE/POWER reader queue (step 2c on page 2-6). Chapter 2. Restoring the BIM-ALERT Installation Tape 2-15

38 Tailoring the Installation Procedure Step 3: Restoring the Installation Tape Step 3: Restoring the Installation Tape Sample Prompt After IALERT1 creates the installation procedure DCMINST, the following prompt is displayed: DO YOU WISH TO RUN THE GENERATED INSTALL PROCEDURE? IF SO REPLY AN EOB ELSE REPLY // GOTO EOJ. Your Response To execute the generated installation procedure, enter EOB. The tape should be mounted on the tape drive you specified in response to question 2 of step 2 on page 2-9. If you want to defer execution of the generated procedure, enter // GOTO EOJ. For more information about deferred execution of the generated installation procedure, refer to page If You Install Version 5.0 into the Same Sublibrary as a Previous Version It is recommended that you not install version 5.0 into the same sublibrary as a previous version of BIM-ALERT. However, if you decided to do so and you did not remove the previous version from the MSHP history file, MSHP issues the following message during the restore operation: M222D DOWNLEVEL CHECK FAILED. CONTINUATION WILL RESULT IN A LOSS OF SERVICE. ENTER "GO" TO CONTINUE OR "CANCEL" TO TERMINATE. This message is merely a reminder that you are installing the new version into the same sublibrary as the old version. If your intention is to install the new version into the same sublibrary as the old version, you can respond GO to the message Installation and Operations Guide

39 Step 3: Restoring the Installation Tape Tailoring the Installation Procedure Jobsteps Executed After the Sublibraries Are Restored After the selected sublibraries are restored from the tape, several jobsteps may be executed depending upon which BIM-ALERT components you installed, and whether you chose MSHP or LIBR to perform the installation. If you installed with LIBR and chose to archive the BIM-ALERT products with MSHP (Step 2, Questions 4 and 5), the next jobstep archives the BIM-ALERT products with MSHP. This lets you apply fixes to BIM-ALERT with the MSHP CORRECT command. If BIM-ALERT/VSE was installed, the next jobsteps rename and replace several phases in IJSYSRS.SYSLIB with phases from the BIM-ALERT residence sublibrary. These phases are also copied into PRD2.SAVE. The following prompt is displayed before the jobsteps execute: TYPE GOTO SKIPRES TO SKIP THE IJSYSRS.SYSLIB COPY/RENAME PORTION OF THE INSTALL. IF YOU SKIP THIS THESE STEPS MUST BE PERFORMED AT A LATER TIME, OR YOU WILL NOT BE ABLE TO ACTIVATE BIM-ALERT. TYPE GOTO SKIPRES TO SKIP THESE STEPS. -OR- ENTER EOB TO CONTINUE. If you are installing version 5.0 on a system that shares IJSYSRS with other systems that will continue to run earlier versions of BIM-ALERT/VSE, type GOTO SKIPRES to skip these job steps. Then build a $SYSOPEN CPU ID table as described in JCL member AXPJCL82.J. When the Job Is Complete When the job is complete, you receive the following message: BIM-ALERT VERSION 5.0 END OF INSTALL PROCESS Review the printout of the installation listings. In particular, check the JCL completion code for each of the jobs. A completion code of 8 or 12 indicates a serious problem that must be resolved before you attempt to activate BIM-ALERT and before you attempt to IPL with SEC=YES. The jobsteps that copy BIM-ALERT/VSE members into IJSYSRS.SYSLIB and PRD2.SAVE may produce a completion code of 4. This should not be considered an error. After reviewing the printout of the installation listings, if you have any problems or questions, contact BIM Technical Support. Chapter 2. Restoring the BIM-ALERT Installation Tape 2-17