RF RGB Remote Control Panel Instruction Rev.05

Transcription

1 This document defined the specification and user instruction for the RF RGB control panel. This RGB control panel was designed for our RF RGB LED flood lights, used to control the light color and color change patterns, the maximum remote control distance is about 100 meters. The remote with touch key control technology, very easy for use. Antenna 140mm Indicator Light Remote Power Switch Color Wheel (8 Single Color Mode) Brightness Increase + Speed Increase + Color Mode (9 Dynamic Color Mode) Lighting ON/OFF Key (Power Key) Brightness Decrease - Speed Decrease - Fig.1 Remote Controller Panel Key Parameters Radio Frequency: 433M Hz, Remote distance: 100M The Size: 85*52*7mm Battery: 3V CR2032 Length of the antenna: 140mm Touch Key control technology Page 1 of 6

2 Functional 1 The control range of RF controller is 100 meters or a little less than 100 meters 2 Eight kinds of static modes (red, green, blue, purple, pink, yellow, orange), nine kinds of dynamic modes 3 1) 25-color jumpy change 2) 7-color gradual changing 3) 3-color jumpy change 4) 3-color gradual changing 5) 7-color jumpy change 6) Red green gradual changing 4 7) Green blue gradual changing 8) Red bule gradual changing 9) Red white blue stroboflash 5 The RF controller can achieve the one-to-one control and one-to-many control. 6 The RF controller can set LED lights address code and RF controller itself address code. 7 The RF controller could set led lights and controller restore factory setting. (Noted: the default factory setting the address code for Floodlight and Remote are: 00) 8 The RF controller control LED lights brightness and speed (Noted: adjust range of brightness: 0-9 adjust range of speed:0-9) 9 Memory function, the lighting can memory the programmed color pattern, user do not need to set the color pattern again after power off (Lighting ON/OFF should be controlled by remote). 10 The control panel using the touch technology for the key, so it is only affected by touch the key. Page 2 of 6

3 Operation for RGB Control Panel The initial address code is 00 for the control panel and LED light ( factory setting), and it is one to many control mode, so the one control panel can control all lightings with any address code. 1.1 Single color - Static Mode A) Slide the power switch to ON, the Red indicator light should be bright up. B) Touch the power key to turn on the LED lighting. C) Touch the color wheel to choose the color, the centre is white color. D) Brightness Increase +, only valid for single color mode. E) Brightness Decrease, only valid for single color mode. 1.2 Dynamic Mode A) Slide the power switch to ON, the Red indicator light should be bright up. B) Touch the power key to turn on the LED lighting. C) Touch the Mode key to choose the different color pattern. D) Speed +, only valid for dynamic color mode. E) Speed, only valid for dynamic color mode. Page 3 of 6

4 Address Code Setting To setting the address code for the control panel and LED light to make the different control and color pattern for the desired color effects. This function can be used for group control and define the different color pattern for different light group. 1. Set the address code for Control panel - One to One Setting One to one means that the one RF control panel could control one led light or one control panel could control many led lights which has the same address code. 1.1 Slide the power switch to ON, the Red indicator light should be bright up. 1.2 Press the Power Key for 3 seconds, (note: the Red indicator light will flash twice). 1.3 Setting the address code for control panel, for example, setting the address code with 01, means the tens digital is 0, single digit is 1. a) First setting is tens digit, press the brightness&speed+ to change to number from 0-9. b) Press Power Key to confirm the tens digit. c) Then Setting the Single digit, by press the brightness&speed+ to change to number from 0-9. d) Press Power Key to confirm the single digit. For example: Setting the control panel with an address code of 01: Because the initial setting is 00 for factory setting, so the tens digit is not required to change, but just press power key to confirm. Press power key for 3s -> tens digit was 0 -> press power key to confirm -> press brightness&speed+ by once (1) -> press power key to confirm -> completed Setting the control panel with an address code of 99: Press power key for 3s -> press brightness&speed+ by 9 times -> press power key to confirm -> press brightness&speed+ by 9 times -> press power key to confirm -> completed Page 4 of 6

5 2. Set the address code for the LED Flood light - One to One Setting To set the LED flood light has the address code same with the control panel, so the flood light can be controlled by that control panel. The flood light should be setted one by one, only power up the one under setting, and turn off others flood light. 2.1 Slide the power switch to ON, the Red indicator light should be bright up. 2.2 Press the Power Key for 3 seconds, (note: the Red indicator light will flash twice). 2.3 Setting the address code for Flood Light, for example, setting the address code with 01, means the tens digital is 0, single digit is 1. a) First setting is tens digit, press the brightness&speed+ to change to number from 0-9. b) Press Mode Key to confirm the tens digit. c) Then Setting the Single digit, by press the brightness&speed+ to change to number from 0-9. d) Press Mode Key to confirm the single digit. For example: Setting the LED Flood light with an address code of 28: Press Power key for 3s -> press brightness&speed+ by 2 times -> press mode key to confirm -> press brightness&speed+ by 8 times -> press mode key to confirm -> completed Page 5 of 6

6 User Notification: 1. The brightness & speed -, can only decrease the number from 9-0, will stop at The brightness & speed +, can only increase the number from 0-9, will stop at At number 9, the Red indicator on the control panel will be no flash when you press the + key, its static bright up. 4. At number 0, the Red indicator on the control panel will be no flash when you press the - key, its static bright up. 5. Must use the Remote to turn on the lighting to achieve the color synchronous for different lightings after AC power on again. 6. The Remote control panel can only control the LED flood light which has the same address code with this control panel, but if the control panel with the address code 00 that can control any lighting with any address codes. 7. Do not press the Lighting ON/OFF key on the remote frequently to avoid the remote goes into address code setting mode, waiting 5 seconds for next press as well, if you found the remote is not so sensitive sometime, just power off the remote and turn on again. 8. When you setting the address code for the LED Flood light, make sure the others LED Flood light was power off. 9. If you forgot what address code you had setted for the lighting and remote, then just change their address code to original 00 by perform the step 1 and step 2 in Address code setting section above, but press brightness & speed to reduce the number to 00. After Sales Service: Thank you order the LED Lighting products from Enersystec Electric Co.,Ltd We hope you have the good experience to use our LED lighting, as we are famous LED lighting manufacturer based in Shenzhen China, we only supply high quality product with excellent after sales service, If you have any concerns about use the products, please contact us, we will response to you within 12 hours, your kindly contact will get professional support from our after sales service team, we looking forward to have long term business with you. We highly appreciated your great Product Review and Store Feedback, you just need 1 minute to do this simply thing, but its really helpful for our sales and encourage us to do better in the future. Thank You Very Much to leave the product Review for us!!! Page 6 of 6