KIP Fold 1000 Offline User Manual
|
|
- Agnes Chase
- 5 years ago
- Views:
Transcription
1 KIP Fold 1000 Offline User Manual
2 Safety Instructions For your protection, please read these safety instructions and the manual completely before operating the machine and keep this manual for future reference close to the machine. Carefully observe all warnings, precautions and instructions on the machine or the ones described in the operating instructions. In order to guarantee hazard-free operations it is strongly recommended that any maintenance or repair work is only carried out by trained personnel. - Symbolss - WARNING: Ignoring this warning could cause serious injury or even death. CAUTION: Ignoring this warning could cause injury or damage to property. NOTE: Indicates additional important information. - General - WARNING: Stop using the machine if a cover was damaged or the machine was dropped. Immediately turn off the power switch and disconnect the supply line. Then call an authorized service partner. CAUTION: Switch the machine off before opening any cover. Alwayss use materials recommendedd for the respective machine. Materials not approved can cause faults in your machine. Do not use the machine when it is emitting unusual sounds. Immediately turn off the power switch and disconnect the supply line. Then call a authorized service partner. - Moving the machine - WARNING: Move the machine carefully and slowly using two persons. Make sure that you disconnected the power cord and other cables before you move the machine. NOTE: Check the documentation for the space requirements before you move the machine. WARNING: - Installation - Make sure that the machine is placed on a level, horizontal surface of sufficient strength. Do not place this machine on an unstable or tilted bench. Set the adjustable feet on the ground when the machine is in the desired position.
3 NOTE: Do not place this machine in a location that is subject to vibrations and shocks. - Maintenance and modifications - WARNING: Do not remove covers or panels which aree fixed to the machine. The machine contains moving part which could cause serious injury. Do not modify the machine, because this could cause electrical shock or fire. To avoid any risk, only properly qualified and trained servicee technicians are allowed to modify the machine. CAUTION: Do not carry out maintenancee activities for other machine components or with other materials than mentioned in the user manual. Use maintenance materials for their intended purpose only. Do not place liquids on the machine. - Power supply - WARNING: This machine is not designed for connection to an IT power supply system. An IT power system is a voltage network in which the neutral wire is not connected to ground. Only connect the power cord to a wall sockett that is equipped with a grounding terminal. Only use the mains connector cable that was supplied with the machine. Do not use a damaged power cord (e.g. exposed core wire, broken wire), this could lead into a fire. Do not use an extension lead to connect the machine. CAUTION: Do not connect the machine to a mains voltage that differs from the value stated on the power marking label. NOTE: If connection to a different mains voltage is required, contact your authorized service partner. - Electricals - WARNING: Do not break any mechanical security interlock switch.
4 Set Up Installation The folder should be set up by an engineer, who has been trained. Environment The room in which the folder is to be placed should be dry and dust free. Humidity should be about 20-80% with room temperature of 15 C to 35 C (59-95 F). The folder must stand horizontally aligned and very stable without shaking. Make sure that the folder to place the folder in a way that does not block exits and allows an ergonomic workflow.
5 Power & Switch On Please use only the connecting cable delivered with the folder. Make sure that the mains supply voltage is identical with your supply. Do not use multi plug extension cords! These cords will not stand thee power consumption of a printer and the folder. The power supply connection is at the right bottom side of the folder. The main switch is at the folder s front side. The display shows a short message as indicated. The Firmware versions are briefly shown in the display. When the folderr has completely started a double beep signal will sound. At the same instance, you will notice the green LED on top of the display illuminate. You will see the folding program last used displayed. In case an errorr is detected during the self test phase, a message will be shown in the display. The message contains error and localization code. Furthermore, a red LED on top of the display will be blinking. Refer to the. After clearing the jam press button in order to restart the folder. There are three LEDs on top of the folder's display: The green LED indicates the folder being ready for safe and normal operation. The red LED is blinking in case of any error. The yellow LED indicates that the folder is busy folding.
6 Display Information next folding program previous folding program presss this button in case the LED is blinking red in order to get detailed information about the error. 1. Folding style 2. Program number 3. Binding margin 4. Panel size 5. Cross fold panel size 6. Status (machine type) 7. Status LED LED 1. green: ready 2. yellow: busy 3. red: error
7 Media & Formats Fan Folder All documents with length from 420 mmm up to 28 folds (20# / 80 gr. Paper) and width up to max. 930 mm. Longer copies will be folded in segments of 28 folds, to be finished manually. Cross Fold All fan-folded sheets until a length of 1200mm can be folded as cross fold. Recommendedd media Best performance with 20# or gr/m² NOTE: Films, plastics or materials with glossy / shiny surfaces are not suitable.
8 Programs There are 8 folding programs available. Through the keys and you select the desired folding program. The selected program number will appear on the left hand side of thee display. The center of the display shows an image of the selected fold style. In Order to change the status of the cross folder or the rotation unit press the cursor will start to blink. Buttons and move the cursor from icon to icon. Selected icons blink frequently. Pressing buttons and edit the blinking setting. Press again within three seconds to save the changes All folding programs can be edited in increments of 1mm within the following range: binding margin: 0-50 mm panel width: mmm Press the cursor will start to blink. Buttons Selected icons blink frequently. and move the cursor from icon to icon. Pressing buttons and edit the blinking settings. Example: Program 1 should process packages 185 mm wide withh a filing margin of 25 mm. Select folding program 1 with button or Press button Press button until the number below the fold package icon blinks Press buttons in order to set the package width to 185 mm Move the cursor forward to the figure representing the margin width
9 With buttons change the value to 25 mm Press button within three seconds in order to store the new values Please notice that the adjustable width of the package must be at least 160 mm up to a maximumm of 230 mm. The range of adjustment of the margin is 0-50 mm. Therefore a packagee of 155/65 is not adjustable. Change the crosss fold length from 200mm to 420mm. Press or to change the value Press
10 Folding Styles Folding programs Program 1-4 are presets (noted below in metric) Select the program by pressing or Folding styles Required style Icon at the display Description Package folding with intermediate fold Package folding with intermediate fold and binding margin Package folding without intermediate fold
11 Free Style Programs A, B, C & D This new innovation i opens the potential of the folder to nearly all possible folding styles, since you can define every layer completely free. This program will not calculate the folding, thatt means: you define a program for a given paper size, so this program will not work for another format. Explanation of signs and numbers in the display: "100 to 420" means: two full panel of the indicated size are folded. "-" means: the folding ends here the last page is to the right upper r exit "<" means: one more fold the last page is to the left lower exit In Order to change values press - the cursor will start to blink. Buttons and move the cursor from icon to icon. Selected icons blink frequently. Pressing buttons the blinking settings. and edit Example Program A should process packages of 135 mm and 180mm wide the rest of paper will determine a filing margin of 30 mm (for A1 sized paper). Select folding program A with button or Press button Press button until the first number beside the fold package icon blinks. Press buttons or in order to set the package width to 135 mm. Press button until the second number beside the fold package icon blinks. Press buttons or in order to set the package width to 180 mm. Move the cursor forward to the next figure With buttons or select < (last page to the left) Press button within three seconds The dynamic icon on the left shows the folding style.
12 Additional Examples
13 First Step Second Step
14 Feeding Prints Thee recommended position is right from the table, feeding the prints with the left hand. Place the left hand near to the rail guide and feed the print into the folder, force it also slightly to the rail guide. Long, small prints need to be guidedd up to the trailing edge. In any case the title block (legend) has to be on the leading edge of the document entering the folder (on the right hand side of the leading edge). Thee fan folded copy must be turned by 90 and thenn fed into the folder again. Thee folder will automatically switch to cross fold. It improves the folding quality if the copy is flattened by hand before the cross fold. Folded copies willl be laid out in the basket.
15 Troubleshooting The LED above the display is blinking red Press in orderr to get the error code Refer to the or report the code to the support. In case of a jam in the fan unit: try to clear the jam automatically by pressing Restart the folder after a jam has been cleaned Clearing a jam in the fan folder Turn rollers by hand
16 Overview Sensor positions
17 Dimensions Metric
18 Inch
19 Error Codes Code Description 21 Error on stepper control boards 21:01 Error on starting stepper control board 21:02 Error on stopping stepper control board 22 Sensor errors on start-up 22:00 Sensor LB0 cut 22:01 Sensor LB1 cut 22:02 Sensor LB2 cut 22:03 Sensor LB3 cut 22:04 Sensor LB4 cut 23 Sensor sends high level permanently 23:00 Sensor LB0 23:01 Sensor LB1 23:02 Sensor LB2 23:03 Sensor LB3 23:04 Sensor LB4 24 Processing errors on stepper control boards 24:01 Error while calculating the step 24:02 Error while counting the steps 25 hardware errors 25:01 Lack of 5 Volts external 25:02 Lack of 38 Volts in FF or CF door open 25:03 Cover open 26 Time out errors 26:01 No ready signal after paper cut 26:02 No paper at sensor LB1 after paper cut 26:03 No paper at sensor LB1 without cut signal 26:04 Jam between sensors LB0 and LB1 26:05 No trailing edge of the paper at sensor LB1 26:06 Too many folds, document is too long 26:07 No trailing edge of the paper at sensor LB0 26:08 Unexpected paper at sensor LB4 in Online-Mode 26:09 Unexpected paper at no fold switch LB5 in Online-Mode
20 Code Description 10 Communication errors 10:01 No communication 10:02 Checksum error 10:03 Bad quality of the data stream 10:04 bad quality of bytes 11 Communication errors 11:01 No communication 11:02 Checksum error 11:03 Bad quality of the data stream 11:04 bad quality of bytes
KIP Certified AutoCAD Driver. KIPFold 2800 User Guide Version SN 1.0
KIP Certified AutoCAD Driver KIPFold 2800 User Guide Version SN 1.0 Safety Read these safety instructions completely before operating the folder and keep this manual for future reference close to the folder.
More informationUser Safety. Electrical Safety. Phaser 4500 Laser Printer
User Safety Your printer and the recommended supplies have been designed and tested to meet strict safety requirements. Attention to the following information will ensure the continued safe operation of
More informationBILL COUNTER OPERATION MANUAL PRODUCT #700012
OPERATION MANUAL PRODUCT #700012 CONTENT 1) Illustration...1 2) Function Controls and Display...2 3) General Instruction...3 4) Safety Instructions... 3-4 5) Power Up...4 6) Counting Function...4-5 7)
More informationPX Series Balances. Quick Start Guide. Please download the user manual from
Scan QR Code with your WebCam for downloading the user instruction manual. PX Series Balances Quick Start Guide Please download the user manual from www.ohaus.com. EN-1 1. INSTALLATION 1.1 Select the
More informationDOT MATRIX PRINTER SP6000 SERIES
DOT MATRIX PRINTER SP6000 SERIES Hardware Manual < Approval: CEL > Trademark acknowledgments SP6000 : Star Micronics Co., Ltd. Notice All rights reserved. Reproduction of any part of this manual in any
More informationEC Series. Safety Guide
EC Series Safety Guide R5906018/02 01/07/2017 Barco Inc, Image Processing 3078 Prospect Park Drive, Rancho Cordova, CA, 95670, USA Phone: +1 916 859-2500 Fax: +1 916 859-2515 Support: www.barco.com/en/support
More information99 Washington Street Melrose, MA Phone Toll Free Visit us at
99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit us at www.testequipmentdepot.com Table of Contents 1. General Safety Requirements... 1 2. Safety Terms and Symbols...
More informationHV-CS kv Edge Mount Triaxial Jack
Keithley Instruments 28775 Aurora Road Cleveland, Ohio 44139 1-800-935-5595 http://www.tek.com/keithley HV-CS-1589 3 kv Edge Mount Triaxial Jack Installation Information Description The Keithley Instruments
More informationPlease read this guide before using the printer
PD-450/450W/480/480W User Guide Please read this guide before using the printer Safety Precautions Safety Precautions Denotes the possibility of serious injury or death Use only recommended power sources.
More informationPRO1250D CT MID DIN rail three phase four wire energy meter. User manual Version 1.5
PRO1250D CT MID DIN rail three phase four wire energy meter. User manual Version 1.5 1 Safety instructions...3 2 Foreword...4 3 CE certificates...5 4 MID certificate...7 5 Performance criteria...8 6 Specifications...8
More informationMOBILE CONNECTOR - GEN 2 OWNER'S MANUAL
MOBILE CONNECTOR - GEN 2 OWNER'S MANUAL UNITED STATES Contents Safety Information... 2 Save These Important Safety Instructions... 2 Warnings...2 Cautions...3 General Information... 4 Mobile Connector
More informationSmartphone Photo Printer
Smartphone Photo Printer Safety Precautions Safety Precautions Denotes the possibility of serious injury or death Please keep you away at least 20cm distance from printer when printing. Use only recommended
More informationInstallation and Operation Back-UPS BR1000G-IN / BR1500G-IN
Installation and Operation Back-UPS BR1000G-IN / BR1500G-IN Important Safety Information Read the instructions carefully to become familiar with the equipment before trying to install, operate, service
More informationSmartphone Photo Printer Item No
Smartphone Photo Printer Item No. 205984 Safety Precautions Safety Precautions Denotes the possibility of serious injury or death Please keep you away at least 20cm distance from printer when printing.
More informationBINDOMATIC 101 DFS Document Finishing System
BINDOMATIC 101 DFS Document Finishing System Operator s Manual Version 2 (2003-02-17) Contents 1. Safety instructions... 3 2. Installation... 4 3. Description... 5 4. How to use the Bindomatic 101 DFS...
More informationTraceTek Leak Detection Master Module Installation Instructions TOOLS REQUIRED STORAGE
TTDM-128 TraceTek Leak Detection Master Module Installation Instructions TRACETEK APPROVALS AND CERTIFICATIONS TYPE NM General Signaling Equipment 76LJ GENERAL INFORMATION Please read these instructions
More informationThis 4200-RM Rack Mount Kit is for installation in 4200-CAB series cabinets only.
Keithley Instruments, Inc. 28775 Aurora Road Cleveland, Ohio 44139 (440) 248-0400 Fax: (440) 248-6168 www.keithley.com Model 4200-RM Rack Mount Kit Packing List Introduction NOTE This 4200-RM Rack Mount
More informationRAINPROOF* COLOR CAMERA SECURITY SYSTEM
RAINPROOF* COLOR CAMERA SECURITY SYSTEM Model 91202 ASSEMBLY AND OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at: http://www.harborfreight.com Copyright 2004 by
More information3.1 Removal Procedures Removing EF-102 from the Main Body Removing Parts from the Tray
Contents 1 Introduction 1.1 Introduction... 1-2 1.2 Safety Precautions... 1-3 1.2.1 Notices for Safety... 1-3 1.2.2 Precautions When Replacing Units... 1-4 1.2.3 Caution Labels and Indicators... 1-6 2
More informationQIT600F1 USER'S GUIDE
QIT600F1 USER'S GUIDE 1 IMPORTANT SAFEGUARDS Warnings: 1. Read all of these instructions. Save these instructions for later use, please. 2. Unplug this monitor from the wall outlet before cleaning. Do
More informationOWNER'S MANUAL. Model:PSV Amp SWITCHING DC POWER SUPPLY.
OWNER'S MANUAL Model:PSV-40 3-Amp SWITCHING DC POWER SUPPLY www.pyramidcaraudio.com FEATURES Your PYRAMID Heavy-Duty 3-Amp Switching DC Power Supply is designed to use AC power-to-power equipment that
More informationInt3233. Soldering Station. Instruction Manual
Int3233 Soldering Station Instruction Manual Thank you for purchasing the Aoyue int 3233 Soldering Station. Please read the manual before using the unit. Keep manual in accessible place for future reference.
More informationTable of Contents. 3.1 Front/Rear Panel and User Interface Front Panel Rear Panel User Interface...
General Warranty OWON warrants that the product will be free from defects in materials and workmanship for a period of 2 years (1 year for accessories) from the date of purchase of the product by the original
More informationModel 8020-KHV. Kelvin Keithley Triaxial Connector Card. Description / October 2014 *P * 1
Keithley Instruments 28775 Aurora Road Cleveland, Ohio 44139 1-800-935-5595 http://www.keithley.com Model 8020-KHV Kelvin Keithley Triaxial Connector Card Description The Model 8020-KHV Keithley HV Connector
More informationV 1.0 ISSUE DATE : Feb.17, 2011
V 1.0 ISSUE DATE : Feb.17, 2011 The following safety precautions are given throughout this manual. They must be strictly followed to protect those who install, use or maintain this product as well as to
More informationiq DIGITAL PICTURE FRAME iq Digital Picture Frame DPF701SB USER GUIDE
iq Digital Picture Frame DPF701SB USER GUIDE 1 Table of Contents Important Safety Precautions... 3 Cleaning the LCD Screen... 3 Cleaning the Digital Picture Frame... 3 Introduction... 4 What s in the Box...
More informationTo Purchase This Game, Visit BMI Gaming Or Contact International Sales at (USA)
The following safety precautions are given throughout this manual. They must be strictly followed to protect those who install, use or maintain this product as well as to protect players, visitors and
More informationX925. Maintenance Guide
X925 Maintenance Guide April 2011 www.lexmark.com Contents...3 Cleaning the exterior of the printer...3 Cleaning the scanner glass...3 Cleaning the ADF parts...4 Cleaning the printhead lenses...5 Storing
More informationModels 2601B, 2602B, and 2604B System SourceMeter Instruments Quick Start Guide
Models 2601B, 2602B, and 2604B System SourceMeter Instruments Quick Start Guide Safety precautions Observe the following safety precautions before using this product and any associated instrumentation.
More informationJanusRAID SA-6692J Hardware User Manual
JanusRAID SA-6692J Hardware User Manual 42-30000-5067 SATA II JBOD enclosure Version 1.1 SA-6692J SATA II JBOD enclosure Hardware User Manual Table of Contents Preface... i Chapter 1 System Requirements
More informationSingle Kernel Grain Moisture Tester PQ-520. (type PQ ) Operating Instructions
Single Kernel Grain Moisture Tester PQ-520 (type PQ-5205-1) Operating Instructions Single Kernel Grain Moisture Tester Safety Precautions Not following the safety precautions could cause an accident resulting
More informationUSER S MANUAL Linear Programmable DC Power Supply APS
USER S MANUAL Linear Programmable DC Power Supply APS-5333 www.tmatlantic.com Table of Contents 1. General Safety Requirements... 1 2. Safety Terms and Symbols... 2 3. General Characteristics... 3 4. Quick
More informationPRO-1250D CT MID DIN rail three phase four wire energy meter.
PRO-1250D CT MID DIN rail three phase four wire energy meter. 1.1 Safety instructions 1.2 Foreword 1.3 MID certificate 1.4 Performance criteria 1.5 Specifications 1.6 Basic errors 1.7 Description 1.8 Dimensions
More informationOperator Manual Ladybird folder
Operator Manual Ladybird folder Ladybird M860LADY VERSION 02 Revision July 2013 SAFETY NOTES... 2 ELECTRICAL SAFETY INFORMATION... 3 OPERATIONAL SAFETY INFORMATION... 3 RADIO FREQUENCY EMISSIONS... 4 REGULATORY
More informationA120 A W/240W PA Mixer-Amplifier 70V/100V
A120 A240 120W/240W PA Mixer-Amplifier 70V/100V User Manual TABLE OF CONTENTS 1. SAFETY PRECAUTIONS...3 2. GENERAL DESCRIPTION......5 3. FEATURES AND FUNCTIONS 3. 1 Front Panel...6 3.2 Rear Panel... 6 4.
More informationSDM120 SERIES. SDM120 series User Manual. Single phase two wire DIN rail energy meter (One module)
SDM120 SERIES Single phase two wire DIN rail energy meter (One module) User manual ------------ 1.1 Safety instruction 1.2 Foreword 1.3 Performance criteria 1.4 Specifications 1.5 Basic errors 1.6 Dimension
More informationFor Sales + Purchasing Info, Click Page To Visit BMI Gaming (800)
For Sales + Purchasing Info, Click Page To Visit BMI Gaming www.bmigaming.com + 561-391-7200 (800) 746-2255 The following safety precautions are given throughout this manual. They must be strictly followed
More informationTA18 active subwoofer. user manual
TA18 active subwoofer user manual Musikhaus Thomann e.k. Treppendorf 30 96138 Burgebrach Germany Telephone: +49 (0) 9546 9223-0 email: info@thomann.de Internet: www.thomann.de 30.11.2011 Table of contents
More informationRT USB RETRACTABLE CABLE
USB RETRACTABLE CABLE Welcome! Thank you for purchasing the MINI-ME RT300-155 USB cable retractor. We know you will find it easy to install, easy to use and easy to maintain. Our goal is to provide our
More informationTABLE OF CONTENTS 1. SAFETY PRECAUTIONS GENERAL DESCRIPTION FEATURES AND FUNCTIONS 4. CONNECTIONS 6. APPLICATIONS...
TABLE OF CONTENTS 1. SAFETY PRECAUTIONS...3 2. GENERAL DESCRIPTION......5 3. FEATURES AND FUNCTIONS 3.1 Front Panel...6 3.2 Rear Panel... 6 4. CONNECTIONS 4.1 Speaker Connections...7 5. OPERATION...7 6.
More informationModel 8020-STC. Kelvin Standard Triaxial Connector Card. Description / October 2014 *P * 1
Keithley Instruments 28775 Aurora Road Cleveland, Ohio 44139 1-800-935-5595 http://www.keithley.com Model 8020-STC Kelvin Standard Triaxial Connector Card Description The Model 8020-STC Kelvin Standard
More information1. Safety instructions
AX-904 1. Safety instructions Failure to follow the instructions listed below may cause personal injury. Read and understand all instructions prior to any operation. Do not remove any label from the tool.
More informationOperation Instruction for CNI Model with PSU-III-LCD
Operation Instruction for CNI Model with PSU-III-LCD Caution-Use of controls or adjustments or performance of procedures other than those specified in this manual may result in hazardous radiation exposure.
More informationFengMi Wemax One Laser Projection TV
FengMi Wemax One Laser Projection TV User`s Manual About electrical ground Transportation Use this device only with a compulsory grounding condition. It is recommended that you use the original packaging
More informationLXEM145 SERIES Lanx Australis single Phase KWh Meter 45Amp. User manual
LXEM145 SERIES Lanx Australis single Phase KWh Meter 45Amp Single phase two wire DIN rail energy meter (One module) 1.1 Safety instruction 1.2 Foreword 1.3 Performance criteria 1.4 Specifications 1.5 Basic
More informationMoving money forward CASSIDA INSTACHECK COUNTERFEIT DETECTOR
Moving money forward CASSIDA INSTACHECK COUNTERFEIT DETECTOR This manual contains important information on safety measures and operational features of the Cassida InstaCheck. Please read it carefully before
More informationPRO1 V21.xxx series MID DIN rail single phase two wire energy meter
PRO1 V21.xxx series MID DIN rail single phase two wire energy meter PRO1D V21.212 Version 1.1 Note: the picture on the frontpage is a meter from the series of this meter, it might not be exactly the same
More informationKIP 720. User Guide. Version QA.1
KIP 720 User Guide Version QA.1 Thank you for purchasing KIP 720. This USER'S GUIDE contains functional and operational explanations for KIP 720. Please read this USER'S GUIDE carefully before using KIP
More informationYST-SW20 SUBWOOFER SYSTEM OWNER S MANUAL. Active Servo Technology
CAUTION SUBWOOFER SYSTEM Active Servo RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS SIDE. REFER SERVICG TO QUALIFIED
More informationDiamond Cabinet Slant Top Users Manual Revision 1.0
Diamond Cabinet Slant Top Users Manual Revision 1.0 1 Table of Contents 1.1 Sections 1 Table of Contents...2 1.1 Sections...2 1.2 List of Figures...3 1.3 List of Tables...3 2 Revision History...5 3 Overview...6
More information3-Phase, Dual-Input 6-Slot Power Supply System STARTUP GUIDE
3-Phase, Dual-Input 6-Slot Power Supply System STARTUP GUIDE -ST-01 Page 1 of 10 November 2016 2016 Copyright Lite-On Technology Corporation ALL RIGHTS RESERVED. Lite-On is a trademark of Lite-On Technology
More informationTest Asset Optimization Services Power Line Utilization Module (PLUM) DATA SHEET
Test Asset Optimization Services Power Line Utilization Module (PLUM) DATA SHEET Description A Power Line Utilization Module (PLUM) is a device used to monitor the utilization and health parameters of
More informationLexmark X203n and X204n Series. Maintenance Guide
Lexmark X203n and X204n Series Maintenance Guide February 2011 www.lexmark.com Contents...3 Cleaning the exterior of the printer...3 Cleaning the scanner glass...4 Cleaning the ADF separator rollers...5
More informationMarshall Lynx LCD Universal Monitors
Marshall Lynx LCD Universal Monitors User Manual Marshall Industrial Video/Security Div. For more information, contact Marshall Electronics, Industrial Video & Security (800) 800-6608 www.mars-cam.com
More informationAuto-Cutter (JM98901) User's Manual
Auto-Cutter (JM98901) User's Manual -2- Contents Notice 3 SAFETY SIGNS that must be strictly observed! 5 1. Function 7 2. Main specifications of auto-cutter 7 3. Checking items inside the accessory box
More informationIf you have questions about your KCD-2000 and its operation, please contact technical support at
This manual contains important information on safety measures and operational features of the KCD-2000 4-way counterfeit detector. Please read it carefully before operating your machine and keep it for
More informationINSTRUCTION MANUAL DISTRIBUTION UNIT. Please read this manual thoroughly before use, and keep it handy for future reference.
INSTRUCTION MANUAL DISTRIBUTION UNIT Please read this manual thoroughly before use, and keep it handy for future reference. ISSUE 1 May 2006 LIMITATION OF LIABILITY THE INFORMATION IN THIS PUBLICATION
More information2016 SIGLENT TECHNOLOGIES CO.,LTD
Quick Strat SDM3045X Digital Multimeter QS06034-E01A 2016 SIGLENT TECHNOLOGIES CO.,LTD Copyright Information SIGLENT TECHNOLOGIES CO., LTD. All rights reserved. The information provided in this manual
More informationHITACHI. EH-150 series PLC EH-RTD8 Resistance Temperature Detective input module Instruction manual. Safety precautions
HITACHI EH-150 series PLC Resistance Temperature Detective input module Instruction manual Thank you for purchasing a Hitachi Programmable Logic Controller. To operate it safely, please read this instruction
More informationEPS Power Supply
EPS - 600 Power Supply Installation and Operation Manual Version 1.0 *This instrument is intended for laboratory use only Index A. Important Notice ----------------------------------------------------------------
More informationVersion /11/2015. User Manual. PowerLine AV HD Gigabit Passthrough Kit DHP-P601AV
Version 1.00 17/11/2015 User Manual PowerLine AV2 1000 HD Gigabit Passthrough Kit DHP-P601AV Preface D-Link reserves the right to revise this publication and to make changes to the content herein without
More informationSAVE THESE INSTRUCTIONS
READ AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION IMPORTANT SAFEGUARDS! When using electrical equipment, basic safety precautions should always be
More informationModel 2460-KIT. Screw Terminal Connector Kit. Description / September 2014 *P * 1
Keithley Instruments 28775 Aurora Road Cleveland, Ohio 44139 1-800-935-5595 http://www.keithley.com Model 2460-KIT Screw Terminal Connector Kit Description The Model 2460-KIT Screw Terminal Connector Kit
More informationOwner's Manual RBC-5000
Owner's Manual RBC-5000 High Speed Bill Counter With Ultraviolet, Magnetic and Infrared Counterfeit Detection Royal Sovereign International, Inc. Please read and retain these instructions. To register
More informationANI SWH. PDU: Per Outlet Control and Total Current Monitoring INSTRUCTION MANUAL
ANI-15115-08SWH PDU: Per Outlet Control and Total Current Monitoring INSTRUCTION MANUAL 122 Rose Ln., Suite 303, Frisco, Texas 75034 TOLL FREE: 1-877-ANEUTRON TOLL: (469) 362-9228 Email: sales@a-neutronics.com
More informationOperation Manual. Concorde 600 Power Supply. *This instrument is intended for laboratory use only.
Concorde 600 Power Supply Operation Manual Cat.no. R10-1001011 *This instrument is intended for laboratory use only http://www.recenttec.com E-mail : support@recenttec.com Version 1.1 Packing List x 1
More informationAVG-UDA2. Features. 2 simultaneous HDMI outputs. Supports Hot-plugging. Compliant with HDMI 1.4, able to transmit 1080p 3D& 4K signals
Features The AVG-UDA2 is a HDMI splitter with the capability to transmit a HDMI or DVI source to 2 displays synchronously. 2 simultaneous HDMI outputs Supports Hot-plugging Compliant with HDMI 1.4, able
More informationUSER MANUAL VIBRATION CONTROL RMA-POWER-BOX 107/230
USER MANUAL VIBRATION CONTROL Version 2.2 1 IMPORTANT NOTES Electrical danger within the meaning of this documentation or the warning labels on the product itself respectively means that death, serious
More informationContents-1. 1 Introduction. 2 Installing Fusing Unit EF Removing Fusing Unit EF Copy/Print Operation.
Contents 1 Introduction 1.1 Introduction... 1-2 1.2 Safety Precautions... 1-3 1.2.1 Notices for Safety... 1-3 1.2.2 Precautions When Replacing Units... 1-4 1.2.3 Warning and Caution Labels... 1-6 2 Installing
More informationModel 2657A-LIM-3 LO Interconnect Module
Keithley Instruments, Inc. 28775 Aurora Road Cleveland, Ohio 44139 1-888-KEITHLEY http://www.keithley.com Model 2657A-LIM-3 LO Interconnect Module User's Guide Description The Model 2657A-LIM-3 LO Interconnect
More informationSERVICE MANUAL Yhu#614 pzz lgkh{laz UG\SGYWX]
SERVICE MANUAL The following safety precautions are given throughout this manual. They must be strictly followed to protect those who install, use or maintain this product as well as to protect players,
More informationSUBWOOFER SYSTEM YST-MSW10
ACTIVE SERVO PROCESSING SUBWOOFER SYSTEM YST-MSW10 Active Servo SUBWOOFER SYSTEM YST-MSW10 Active Servo HIGH CUT HIGH LOW OWNER S MANUAL MANUAL DE INSTRUCCIONES CAUTION RISK OF ELECTRIC SHOCK DO NPT OPEN
More informationTABLE OF CONTENTS TABLE OF CONTENTS... 1 IMPORTANT SAFETY NOTICE...
TABLE OF CONTENTS TABLE OF CONTENTS... 1 IMPORTANT SAFETY NOTICE... 2 1.0 General Information... 3 1.1 System Components... 3 1.2 Specifications... 3 1.2.1 Torque Ranges... 3 1.2.2 Electrical Specifications...
More informationModel 2380 Rack-Mount Kit
Keithley Instruments 28775 Aurora Road Cleveland, Ohio 44139 1-800-935-5595 http://www.tek.com/keithley Model 2380 Rack-Mount Kit Installation Instructions Introduction The Model 2380 Fixed Rack-Mount
More informationStartup Guide C01
Startup Guide 4012988-00 C01 Startup Guide English Where to Find Information........................ 2 Safety Instructions.............................. 4 Important Safety Instructions...........................
More informationBAS H Series Programmer
BAS H Series Programmer INSTRUCTION MANUAL Please read this manual before using the machine. Please keep this manual within easy reach for quick reference. Thank you very much for buying a BROTHER sewing
More informationImportant Information KX-NTV150. Communication IP Camera. IP Video Doorphone. Model No. Model No. KX-NTV160
Important Information Communication IP Camera Model No. KX-NTV150 IP Video Doorphone Model No. KX-NTV160 Thank you for purchasing this Panasonic product. Please read this Important Information carefully
More informationINFORMATION AMPLIFIER TA-102 OPERATING INSTRUCTIONS TABLE OF CONTENTS
OPERATING INSTRUCTIONS INFORMATION AMPLIFIER TA-102 INFORMATION AMPLIFIER TA-102 MIC AUX POWER TABLE OF CONTENTS 1. SAFETY PRECAUTIONS... 2 2. GENERAL DESCRIPTION... 4 3. EACH PART NAME AND FUNCTIONS Top
More informationLED BEAM 300 LED-MB50. User. Guide. Professional Entertainment Technology
LED BEAM 300 LED-MB50 Guide User Professional Entertainment Technology TABLE OF CONTENTS 1. Safety Instruction 2. Technical Specification 3. How To Set The Unit 4. How To Control The Unit 5. Troubleshooting
More informationProfessional Entertainment Technology LED BEAM 300 LED-MB50. Innovation, Quality, Performance 23-
Innovation, Quality, Performance 23- LED BEAM 300 LED-MB50 User Guide Professional Entertainment Technology EC Declaration of Conformity We declare that our products (lighting equipments) comply with the
More informationTABLE OF CONTENTS ADJUSTING YOUR LCD MONITOR
TABLE OF CONTENTS ADJUSTING YOUR LCD MONITOR -------------- 2 General safety precautions. 2 Unpacking your monitor 5 Viewing angle 6 How to open the back cover 6 Connecting your monitor 7 User controls
More informationInstruction Sheet Updating SmartPAC 2 Firmware
Instruction Sheet Updating SmartPAC 2 Firmware This document shows you how to update SmartPAC 2 firmware, using a USB disk, and load SmartPAC 2 firmware installed on a replacement Compact Flash (CF) card.
More informationInstallation and Operation Guide for PD5200 and PD5300 Automatic Transfer Switch
Installation and Operation Guide for PD5200 and PD5300 Automatic Transfer Switch PD52 PD52S & PD52DCS PD53-100 te: The PD52S & PD52DCS are provided with LED lights. The GREEN LIGHTS indicate Shore Power
More informationUSER MANUAL. For XLCD17-LED XLCD19-LED
USER MANUAL For XLCD17-LED XLCD19-LED 2 TABLE OF CONTENTS CE information ------------------------------------------------------------------------ 4 Safety Precautions -------------------------------------------------------------------
More informationKIP 2300 USB3. User Guide. Version QA.1
KIP 2300 USB3 User Guide Version QA.1 We highly appreciate your purchasing our KIP 2300 Image Scanner. This User's Manual contains functional and operational explanation for KIP 2300 Image Scanner. Read
More informationIN5132/IN5142/IN5134/IN5134a IN5144/IN5144a/IN5135/IN5145 User's Manual (detailed) Instant Stack Guide
Projector IN5132/IN5142/IN5134/IN5134a IN5144/IN5144a/IN5135/IN5145 User's Manual (detailed) Instant Stack Guide Thank you for purchasing this product. Features This projector can be used in conjunction
More informationProfessional Entertainment Technology LED BEAM 300 LED-MB50. User. Guide
Professional Entertainment Technology LED BEAM 300 LED-MB50 Guide User 1- 1. Safety Instruction WARNING Please read carefully the instruction, which includes important information about the installation,
More informationB&W RearView Camera Installation & Operation
B&W RearView Camera Installation & Operation CA52 (Camera) FOR MORE INFORMATION WWW.STRATEGICVISTA.COM BEFORE OPERATING THIS SYSTEM, PLEASE READ THIS MANUAL THOROUGHLY AND RETAIN IT FOR FUTURE REFERENCE
More informationModel 7705 Control Module
www.keithley.com Model 7705 Control Module User s Guide PA-696 Rev. D / October 2006 A G R E A T E R M E A S U R E O F C O N F I D E N C E Safety Precautions The following safety precautions should be
More informationINSTRUCTION MANUAL. * Design and Specifications are subject to change without notice. ver. 1.0 PRINTED IN KOREA
INSTRUCTION MANUAL * Design and Specifications are subject to change without notice. ver. 1.0 PRINTED IN KOREA INSTRUCTION MANUAL Thank you for purchasing this product. For proper usage and application,
More informationLine reactors SINAMICS. SINAMICS G130 Line reactors. Safety information 1. General. Mechanical installation 3. Electrical installation
Safety information 1 General 2 SINAMICS SINAMICS G130 Mechanical installation 3 Electrical installation 4 Technical specifications 5 Operating Instructions Control version V4.7 04/2014 A5E00331462A Legal
More informationALO Duo Roll DMX LED barrel scanner with dual light source
ALO Duo Roll DMX LED barrel scanner with dual light source User manual Safety instructions WARNING! Always keep this device away from moisture and rain! Hazardous electrical shocks may occur! WARNING!
More informationSAMURAI SCAN 50 LED-SC50D. User Guide. Innovation, Quality, Performance. Professional Entertainment Technology 19-
SAMURAI SCAN 50 LED-SC50D Innovation, Quality, Performance User Guide Professional Entertainment Technology 19- EC Declaration of Conformity We declare that our products (lighting equipments) comply with
More informationOmnitron Systems Technology, Inc. 1. iconverter. 19-Module Managed Power Chassis User s Manual
Omnitron Systems Technology, Inc. 1 iconverter 19-Module Managed Power Chassis User s Manual 27 Mauchly, #201, Irvine, CA 92618 Phone: (949) 250-6510; Fax: (949) 250-6514 2 Omnitron Systems Technology,
More informationEnglish User s Manual
User s Manual M00061801EN All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying,
More informationPart No. Z , IA Mar OPERATION MANUAL. High Voltage Digitalmeter A
Part No. Z1-109-820, IA001704 Mar. 2011 OPERATION MANUAL High Voltage Digitalmeter 149-10A Use of Operation Manual Please read through and understand this Operation Manual before operating the product.
More informationBlue Weapon Laser. User manual UK. Version 1.0
Blue Weapon Laser User manual 152.754UK Version 1.0 CAUTION 15. Disposal : Please disposal of the unserviceable device according to the current statutory requirements. Please read this manual fully before
More informationOV1000 Part No OV1000 HEIGHT ADJUSTABLE TABLE USER GUIDE
OV1000 Part No. 23624 OV1000 HEIGHT ADJUSTABLE TABLE USER GUIDE PRODUCT OVERVIEW User Guide: OV1000 OV1000 HEIGHT ADJUSTABLE TABLE A healthier work environment starts with the option to sit or stand throughout
More informationXTM1250SA DIN rail three phase four wire LCD display energy meter
XTM1250SA DIN rail three phase four wire LCD display energy meter 1.1 Safety instruction 1.2 Foreword 1.3 Performance criteria 1.4 Specifications 1.5 Intrinsic errors 1.6 Description 1.7 Dimensions 1.8
More informationLight Brick ORDERCODE 50370
Light Brick ORDERCODE 50370 Congratulations! You have bought a great, innovative product from Showtec. The Showtec Light Brick brings excitement to any venue. Whether you want simple plug-&-play action
More information