Chrysler video IN Motion adaptor

Transcription

1 Chrysler video IN Motion adaptor 1. With OEM cable harness for plug and play, do not need any weld and cutting cable to finish installation 2. To be suitable fort Chrysler, Dodge, Jeep 2007 up version with MYGIG Radio.( REC and REC to MYGIG Radi, please contact us) 3. 4 RCA input function, can connect with DVD, TV, Rear camera, Front camera, and GPS BOX. Special GPS function can be operated by original touch monitor by BABY CAM input % origial car button operation, and original touch switch function. To Unlock original DVD, TV while car moving or not in any time, and any where accordingt o your requirement. 5. When after-market GPSBOX by BABY CAM input, you can use the original touch monitor to operate the NAVI MAP system. 6. With Ipod function input, with original stereo sound system transmittion.(this function is optional, please contact the supplier) 7. All the sound it transmittion by the original system with excellent steroe result. 8. Can Instal Front, Rear, Side camera, can be operated by auto, and Manual set to activate these cameras. DIP SETTINGS: PIN1: Always UP PIN2: Always up PIN3 PIN4:UP PIN3 PIN4: Down PIN5: Always Down If PIN1 Down,to Lock all AUX video inputbut Rear camera, and Navigation is valid When car is in low speed When car is in high speed Installation: 1. Remove the front panel of the Radio, then to pull out the RADIO, you can see the original OEM cable connect. Unplug the gray connector from the monito, then to plug

2 this gray connector with our gray connector. 2. Unplug the original white connecto from the Radio, to connect with our white connector. 3. Our other side femal Gary and white connector to connect with the original Radio as the below picture: 3. After installation the gray and white connector,pre-set the DIP SETTINGS inot the connect position before the unlock unit to connect with the OEM cable harness. If you set the DIP set after the unlock unit connect to the oem cable harness, the Pre-settings will be not available. And if you find the DIP settings is wrong after connect the unlock unit to the OEM cable harness, you must remove the unlock unit from the cable harness, and uplug the cable from the Radio, then to re-set the DIP SETTINGS again type of cars,some 2010types,the original Rear Camera can be only activated whenthe gear reverse position If you want to operate the Rear camera anytime, then you need to use our OEM cable harness REVERSE CAM POWER cable to connector the original rear camera +12V power cable. Then you can operate the rear camera in anytime. And if you do not connect REVERSE CAMERA POWER to the original +12V power cable, then the rear camera can t work when the gear in other position, or the monotor is black, or the picture is flating. When connect our REVERSE CAMERA POWER to original rear camera +12V cable, you need to cut this cable, to connect our this cable of REVERSE CAMERA POWER, and the original rea camera +12V will be not application again. But be sure the cable what you cut is original rear camera +12V cable. 5. If the car is not with original rear camera, then the cable REVERSE CAMERA +12V can connect the the rear camera +12V to activate the fater-market rtea camera, and the Groudn is also provided by our cable harness. 6. the Unlock unit can alos be also add side and front cameras. Our cable: ADD CAM POWER +12Vis designed separatedly to supply +12V cameras power to these after-market,

3 and Groudn to camewra Ground connection, then use RCA slot to input the cameras signals. These cameras function can be operated by auto settings, and Manual settings. 7. cable marked: +12V ACC OUTPUT:ACC +12V output is for supplying +12V power to othervideo unit added in car. The Rate is about 1.5AMPS,with car activation If more than 1.5AMPS, need to connect CONSTANT +12V OUTPUT,by the unlock ACC relay switch. Mark::YELLOW:+12V CONSTANT BATTERY POWER RED:ACC IGNITION POWER BLACK:GND Orange S/W:REVERSE POWER RED S/W:FRONT/BABY CAM POWER Those cable is supply power to the after-marked video unit fix in car, please do not worriedabout will over-consumption the power, the rate is just only 1.5AMPS. and over 1.5AMPS rate will be switched by the ralay. Our cable harness marked: ACC and +12V is just for after-market vidoe unit power supply,do not need to connect car ACC, and car +12V, or it will damage our unlock unit, or cause our unlock unit can t work well. When first time ot activate the unlock unit, need about 30 second to activate the unit all functions.,then the original Radio MENU will show SATV, then to touch SATV, you can operate the unlock unit functions easily, and simply. If you want to unlock the original DVD, TV, and add AUX only, then you can only just connect with our OEM cable to car and our unlock unit is ok, do not need to open the original Radio. Operation and Switch: There arte three ways to operate the Unlock unit, and the AUX unit: 1. By Radio original Button to switch and select the MENU item 2. By Steering Wheel original Button to control and switch the Unlock unit or AUX functions. 3. By Original Touch Screen to switch Unlock unit or AUX video unit.

4 B After finishing installation, power on, then the Radio MENU Show as the above Clich SATV, then in the right side will show some of the functions, there are 4 pages. You Can touch the Item what you want to operate BABY CAM is special for connecting external GPSBOX by RCA input, then touch BABY CAM Then you can operate the NAVI MAP by original touch screen IGO8 NAVI SYSTEM activating IGO8 NAVI MAP Actication IGO8 NAVI MAP system operation

5

6 The Golden Cable: This connector is for conneting original monitor Golden cable connector, see the Below picture : This connector is for connecting original Radio PCBconnector. See the below Picture: After The Golden cable connect with the original Gloden cable connector, please put this connector Under side of the original Radio PCB to sure The original Radio cover can fix it back well, Tightly and easy. the Picture after finishing installating The Golden cable.

7 The Picture after finishing installation Golden cable connect back the cover to PCB. Finish the installation then to cover back the radio To Unlock Touch slot To connect Golden 6PINS connector To connect GPS BOX 4PINS touch output connector For connecting External GPS BOX RCA output signal, then you can use the Original Touch screen to operate the NAVI map on the monitor after finish the all installation.

8 IGO8 NAVI MAP Going Unlock unit for car list Please reference the below table list to check what your car is,and then to set the DIP Switcher into the correct Position Low speed:dip 3 4up High speed:pin3 PIN4 Down CHRYSLER SEBRING CHRYSLER TOWN and COUNTRY DODGE AVENGER DODGE CARAVAN CHRYSLER 300 和 300C DODGE NITRO DODGE DURANGO DODGE LIBERTY CHRYSLER ASPEN JEEP WRANGLER DODGE CHANGER JOURNEY DODGE DAKOTA DODGE RAM JEEP GRAND CHEROKEE JEEP GRAND CHEROKEE 2011 JEEP COMMANDER CHRYSLER CHALLENGER PATRIOT/COMPASS When installation, please must set the DIP3, 4into correct position. When set the wrong position, the original Radio will not work, but should not damage the original Radio. So at the moments, you need to unplug and unlock unit from the cable harness, and also unplug the cable harness from the car, then to set the DIP switcher into the correct position, and connect the cable harness.