360º 4CH Vehicle Surveillance System

Transcription

1 360º 4CH Vehicle Surveillance System 4 CH DVR / All in one 4CH Vehicle Surveillance Camcorder User Manual 2016 NOV V1.0 optional

2 Safety Precautions For ensure device working correctly, please test record and play video function before use. Please note that manufacturer, subsidiaries, affiliates, and distributors are not liable for any consequential damages arising from any malfunction of main device accessory. Including the losses cause by memory card that failed to record image or recorded files unable to read on any device. Before using the product, please ensure that you read the safety precautions below. And always make sure the product is used correctly. Please keep device away from children. Only using the power supply as manufacture recommended. Do not attempt to disassemble, alter or heat the product. To avoid the risk of injury, do not touch the interior of the product if it has been dropped or otherwise damaged. Stop using the product immediately if it emits smoke, a strange smell, or otherwise behaves abnormally. Do not use organic solvents such as alcohol, benzene, or thinner to clean the product. Do not let the product come into contact with water (e.g. sea water) or other liquids. Do not allow liquids or foreign objects to enter the VVR. Do not place the VVR nearby or direct touch flame. Do not handle the power cord with wet hands. Do not use the equipment in a manner that exceeds the rated capacity of the electrical outlet or wiring accessories. Do not use the damaged power cords or plugs, or the power cords or plugs were not fully plugged into the outlet. Do not allow direct or metal objects (such as pins or keys) contact with the terminals or plugs. Avoid using, placing or storing the product in the humid or dusty areas i

3 Table of Contents A. Features... 1 B. Specifications... 2 C. Accessories... 5 D. Product Dimension... 6 (1) Mobile DVR Dimension... 6 (2) Vehicle Camera Appearance E. ON /OFF F. Remote Controller Introduction G. Real Time Monitoring Mode H. OSD Main Menu Operation And Parameter Setting Description I. Playback J. PC Player (1). Control Tools list (2). Playback Tools List (3). Capture (4). Configuration (5). Backup (6). Playback (7). Format (8). Video playback speed (9). MAP (10). G-SENSOR ii

4 (11). Video playback progress (12). Volume (13). Control panel (14). Direction, Latitude and longitude (15). Speed per hour K. Format the SD card (1). Format on Recorder (2). Format on PC L. Restore the SD card M. Wifi Setting (optional) iii

5 A. Features 1. Mobile DVR with 4CH 360 surrounding view cameras. Additional option is the 1CH Parking assist camera, which can automatically change rear image during parking. 2. Video output can connect with external monitor, watch and playback by PC player. 3. Recording format:720p, 25/30FPS. 4. GUI Graphical control interface 5. Built-in Supercapacitors, automatic keeping recoding after turn off engine, ensure recoding files write back to SD card. 6. Integral and reliable event record table, make recording files easy to search and find. 7. Integral Time and date record, which can display and play by monitor. 8. After insert SD card, do not require any action, the device will start recoding automatically. 9. The video record files save by SD card, against shock and vibration during drive. 10. Built-in Internal 3D G-Sensor, device activates G-sensor during happening event. 11. GPS offer vehicle s speed, direction, and route track records. (optoinal) 12. Can watch and backup video records by connect with external USB WiFi dongle. (optoinal) 1

6 B. Specifications Mobile DVR Terms Video Input Resolution Power Specification 4CH 720P 360 surround view camera 1CH parking assist camera (optional) 720p 360 surround view cameras: CH1(Front)+CH2(Right)+CH4(Left)+CH3(Rear), auto activate parking assist image. Default recording: ch 25/30 fps. (a) DC12V, Max power approx. 1.25A. (b) DC12V, ACC OFF, power approx.30ma. (c) Working Voltage:DC8.0v ~ DC32.0v. Delay Record function Temperature Storage Recording Recoding Contents Storage Format Audio Input (d) Activate Voltage>DC11v. (a) ACC OFF, delay power support for approx.3 sec. (b) Built-in supercapacitors delay recording time approx.3sec, and then write buffer record data back to SD card. Operation Temperature:-20 ~60 (Non-confined spaces with natural ventilation) Storage Temperature:-40 ~85 SanDisk class10 and 8G above SDHC card. Some specific devices require the vendor recognizes SD card Automatic recording after activate device in 30sec. Image, Data, Audio, GPS info (optional). External trigger signal and G-sensor data. Using specific file format, require dedicated player Directly playback on the device. Using specific signal format, require dedicated play 2

7 monitor Time setting Display Dimension Weight (a)auto GPS adjustment, active calendar clock when device cannot receive GPS signal. (b)the first time device installment requires use GPS time adjustment. After finished the adjustment, RTC time will support by vehicle power. The time has to reset if device power off. TV-Out Video output AV-Out Audio output.(av terminal) 115mm x 132.7mm x 30mm (Width x Depth x Length) 0.4kg (Include SD Card) Note: 1.Storage device is not includes in the product set, please purchase it separately. 2. No further notification on product specification changes.. 3

8 Vehicle Camera Signal Type NTSC / PAL Sensor 1/4 inch CMOS *4PCS Video processor Digital signal manage system Pixel 1280 x 720 Total pixel Approx. 1.0 million Resolution 720P Input voltage DC 12 ± 1V Current 280mA(IR OFF) / 340 ma(ir ON) Sync. system Internal Synchronization Scan system 2 : 1 crossover scan Sensitivity 3300mV/(Lux-sec) / 0Lux(IR ON) Signal to Noise Max. 37 db Ratio Auto-zenith ON control Dynamic range 64 db Auto-balance Automatic ON Shutter status Automatic ON Viewing angle H : 360 V : 70 Signal output 1 Vp-p standard video output,75 Ω format IR LED 4PCS IR range 1m Operation - 10 C ~ +60 C Temperature Note: No further notification on product specification changes. 4

9 C. Accessories 1. Standard Set: (1) Device (2) Camera (3) Power cord (black/blue/red) (4) Alarm cable (5) IR extension cord (6) Remote controller (7) Microphone (8) Velcro strap (9) Double-side3M tape (10) Bracket mount (11) CD (12) Quick start guide 2. Optional Accessories: (1) USB interface SD card reader. (2) 4/8/16/32G Class10 above SD card (3) GPS Module (4) USB WIFI (5) External connect AVM-1250 Vehicle Camera 5

10 D. Product Dimension (1) Mobile DVR Dimension (1). Power Light (2). Recording Light (3). Wifi Light(optiona (4). GPS Light(optional) (5). IR receiver (6). SD Card Slot (7). GPS Connector: For connect with G-Mouse to use GPS function. The GPS function includes record vehicle location, speed, longitude and latitude. (optional) (8). EXT: Video output jack, connect with parking assist camera (9). MIC: Microphone jack, connect and record audio 6

11 with microphone. (10). Composite cables :including video output, audio output and USB connector. (11). Alarm Input: Alarm input connector, use by parking assist camera. (12). Camera Connector: Connect with dedicated vehicle camera, which able to record 360 surrounding view. (13). IR Extension Cable Connector: Once upon connecting with the extension cable, the IR receiver will only receive signal from extension cable, cannot control by remote controller. (14). Power Connector: To cooperate with power management function (in OSD), it can provide delay shut down function. Power Cable (Black/Blue/Red) 1. Positive Port (Red cable): DC8~32V power input. 2. ACC Control (Blue cable): Can setup delay shut down recording after turn off engine. 3. Negative Port(Black cable): GND 7

12 Alarm Cable(Black/Yellow) 1. Positive 12V ALARM Input (Yellow cable): Connect with Positive port on parking assist camera. 2. Negative GND(Black cable): GND Memory Card installation Dust cover (1). To loosen the screw, twist the screw clockwise or counterclockwise. And then open the dust cover for insert or remove memory card. (2). Format/Restore Memory Card refer to other chapter instruction. NOTE:Memory Card requires to purchase separately. 8

13 Notice (1). Suggest to use SanDisk SDHC Card (Class 10/ 4G at least) (2). When using a new card, please format SD card in main engine or player first (3). Before using the memory disk, please format the disk first using the software player in the CD-ROM. If not, device will automatically erase all data in the memory disk before recording. (4). Please do not use Micro SD card adapt to SD card for using, it may cause connect error when vehicle moving and shocking. (5). Memory card has life limit. For ensure it working correctly, please test the memory card on PC Player regularly. 9

14 (2) Vehicle Camera Appearance 1. Lens 1 (Front) 2. Lens 2 (Right) 3. Lens 3 (Inner) 4. Lens 4 (Left) 5. Cable collect slot 6. 3M Double-side tape Dimension (Unit: mm) 10

15 Vehicle Camera Installation Diagram 1. Install camera on windshield by adhesive bracket 2. Pick up a best location for installation. 3. To adjust a best view angle. 4. To connect power cable to Mini USB hole. 5. To connect the other end with the Video In slot in DVR. 11

16 Notices For installation by none-technician, please use tapes instead of boring tools to avoid damaging the electrical and gasoline system. For safety, switch off ignition before installation, and please keep away from gasoline pipeline and tank. To ensure recording quality, please do not use adapter card with Micro SD card. Doing so may lead to bad connection due to shock and vibration Before inserting wires through holes, temporarily wrap the terminal with tape to prevent bad connection from accumulated dirt or debris. Tightly seal all electrical connection with tape to prevent loose connection or water leakage to the connection. Connect the power behind the key ignition and fuse (not directly to the vehicle battery) to avoid depleting the battery The device should be fixed to the vehicle. Tumbling inside the storage trunk will cause device damage. GPS positioning accuracy may be affected by the installation position, sun-screen or weather condition. Vehicles without electromagnetic interference certification may interfere with the operation camera, led to abnormal interrupted recording image. When the connector touched sand, dust, grease and so on, cleaning the connector with alcohol, to avoid poor 12

17 video signal case abnormal video. Devices normally divided into two systems: NTSC or PAL. For using the correct device, ensure the system type meet the usage environment requirement. Devices video output normally divided into two systems: NTSC or PAL. Ensure using suitable system according to different devices and monitors. The compatibility issue may show up if manufacturer change the manufacture progress. This device cannot ensure compatible with all memory card type. Please change different memory card brand if have the compatibility issue. The device has standby current, when the vehicle is not used for a long time. Please unplug the power supply to avoid battery power runs out, and reset the time after the reconnection. Before using the memory disk, please format the disk first by the software player. If not, device will automatically erase all data in the memory disk before recording, then recording as default setting. Some specific camera cannot record unless formatted memory card. The boot and real-time view screen presentation may be due to software updates, revised and changed without notice. Memory card has life limit. For ensure it working correctly, please test the memory card on PC Player 13

18 regularly The collision and high frequency vibration may cause physical damage to the memory card magnetic field, resulting in video intermittent or unable playback.it is recommended that regular inspection and backup important data. For prevent video files adjust and rewrite, please remove the SD card and setting read only before the accident happen. For avoiding power supply abnormality and short circuit, switch off power supply before the install or remove camera. The device will turn off without ACC signal. The device working relates on battery power. After shut down battery power, device has to adjust the time by GPS. 14

19 E. ON /OFF ON: Insert SD card into slot in main engine, connect the power to start. Turn on the device need to be waiting for approx. 30 sec. until the power light on. OFF: The device requires waiting for approx. 5 sec. delay to run out supercapacity power after turn off the power supply. After supercapacity run out completely, user can remove SD card and read SD card files on PC. Light Signal: Power Light (GREEN): No light = No power supply. Light on = Stable power supply. Recording Light (RED): No light = No recording. Light Blinked = Recording. Light Blinked Fast = Force recording. GPS Light (BLUE) (optional): No light = Not position yet. Light Blinked = Position successfully 15

20 WiFi Light(Orange) (optional): No light = Not connecting with WiFi Light Blinked = WiFi connecting (NOTE: The device cannot recording during video playback on itself.) 16

21 F. Remote Controller Introduction Button Description No. Description No. Description 1 Split screen 7 Enter display 2 Force Record 8 Fast Rewind (not availabve yet ) 3 Quad display 9 Fast Forward 4 Mute 10 Play back 5 Menu 11 Pause 6 Arrow keys 12 Stop 17

22 How to check if the remote controller is not workable? Check the mercury cell is installed in Correct direction. (Check the pole) Check the cell power is exhaust or not. Check the sensor is covered or not Check if it nearby Fluorescent Lamp. 18

23 G. Real Time Monitoring Mode (1) Monitor Screen Operation Instruction: For display 1~4 channel separately, use remote controller switch channel. To show quad display, press the quad display button. To open menu, press Menu button. To playback, press Playback button. (2) Icon Description: : Recording : GPS sensor position successfully. (optional) : Microphone ON : Activate event recording : Alarm 19

24 H. OSD Main Menu Operation And Parameter Setting Description Recording Setting Record FPS Record Quality NTSC 720P 5-30fps VGA 5-30fps PAL 720P 5-25fps VGA 5-25fps Regular Good Excellent Image Setting Time Setting GPS Setting (optional) Vehicle License Plate Number Operating Mode Alarm Setting Setting the brightness, contrast, color adjustment by chooses different channels. When GPS signal successful positioning, the system will automatically adjust time and time zone by GPS. If device cannot receive GPS signal, user can directly setting the time on device Select and display the vehicle speed and speed unit on real time video screen. Input range: A~Z and 0~9 1.Setting default channel mode 2.Setting delay recording time after press ACC off 3.Audio record ON/OFF After trigger alarm, beginning parking mode 20

25 Protection System G-Sensor Camera setting Backup Restore default Setting Format Hard Disk Hardware Upgrade 1.Low voltage protection (this function activate by ACC mode) 2. Disk protection prompt The DVR will activate force recording function, which ensure device keep recording and avoid overwrite records during vehicle collision accident. Enter suitable camera resolution format as 720P or D1(Enter incorrect resolution format will let to screen display error) Select backup time. During the selected time, device can backup files by connect with USB. After restore default setting, the DVR will restart and restore default setting data. All the records will delete with Hard Disk format. Transfer files from hardware to the SD card, and insert the SD card into DVR to upgrade. DVR cannot interrupt power during updating the hardware. After hardware update completed, the DVR system will reboot automatically(if insert two SD card, upgrade file will mainly save on the SD1) 21

26 I. Playback Playback mode There are two ways to playback recorded footages: directly playback on device and playback in PC. Playback on device (1) Press play button under Real Time Monitoring Mode, and then get into playback page. (2) Select research methods and press enter button to see the playback files list. (3) Select one of playback files, press enter to play this video. Playback in PC: Playback video by SD card (1) Insert the SD card in PC, click and run the software CarBox2.exe. (2) Click the Video Playback,open the playback page. (3) After selected hard disk, player will display video playback list, choose and play video from this list as 22

27 user requirement. 1. Select SD card 2. Select playback video (NOTE:If cannot read SD card under WIN7, please right-click CarBox2.exe Icon and choose run as administrator) 23

28 J. PC Player Run the CarBox2.exe, display interface as below. Note: Run this software require install DirectX 9.0 or above. Control Tool List CH1(Front view) Video speed CH4(Left view) CH2(Right view) G-Sensor Playback progress Volume control Playback tools list Vehicle Speed Per hour CH3(Inner view) GPS Latitude and Longitude NOTE: After device triggered alarm, the CH3 can automatically change to the rear image that recorded by parking assist camera. (1). Control Tools list Capture: Screen shoot, Click the icon to capture the footage screen. Configuration: Change the general device setting Backup: Choose suitable folder to 24

29 backup files. Playback: select and playback video files from hard disk or personal computer. Format: Hard disk format and language setting. (2). Playback Tools List Previous File Previous Frame Backward Play Pause Stop Play Next Frame Next file (3). Capture Capture: Click capture icon to capture the footage screen. The captured image will save as.bmp format. The player will automatic showing the Snapshot folder after success capture image, the default image saving route as the snapshot folder that under Player installation. 25

30 (4). Configuration Image Quality FPS Vehicle Info. UI Mode Password Time Zone Choose the resolution: High /Normal / Low Resolution setting range: 5~30 Fps Enter vehicle license plate number or diver name (Suitable for company vehicle, taxi,convoys, and other groups) Setting the screen size of player This feature encrypts the hard drive to prevent other person access to data. Set the password up to 15 characters. For access the file, setting, and format disk require enter the password. Note: pay attention with capital letter during password setting, keep your password safely prevent password forgetting. Greenwich Mean Time, adjust it with 26

31 desired time zone to display. Speed Unit G-sensor Sensitivity Daylight saving Time Set and display speed unit as: Km/h Mile/h Knot Setting the G-sensor Mode and sensitivity Applies to countries implementing daylight saving time (5). Backup Choose suitable folder to backup files. Click icon to backup function as the start backup page below: Step 1. Choose the SD card with video files. 27

32 Step 2. Select the file as your desire for backup. Step 3. Choose the save format for backup file Backup format: SD format Backup as *.sd format AVI format Backup as.avi format Note: Files that backup with *.sd format will contain image/speed/location and G-Sensor data. Files that backup with.avi format will only record video and audio data. Therefore, we strongly recommend backup file with *.sd format. Step 4. Schedule the backup time as your requirement. 28

33 Step 5. Select backup route and folder. Step 6. Begin to backup file. (6). Playback Playback Video:Select and playback the video from SD card or personal computer. 29

34 1. Choose the Local Disk, Removable Storage or Backup File 2. Choose the file (7). Format Format:Includes format SD card, restore SD card, language setting, and query software version. Details about Format and restore SD card refer to next chapter. 30

35 (8). Video playback speed Video playback speed: capable for adjust it playback speed as 2x~16x high and 1/2x~1/16x low (9). MAP Map:display as Google Map, the vehicle diving route and location. (This function requires the device mode with GPS, and optional G-Mouse) (10). G-SENSOR G-SENSOR: Gravity sensing analysis, after triggered the G-Sensor force recording, system will show and record the X Y Z axis change. 31

36 X: Horizontal change (Left and right) Y: Horizontal change (Front and rear) Z: Vertical change (11). Video playback progress Video playback speed: capable for adjust it playback speed as 2x~16x high and 1/2x~1/16x low (12). Volume Volume control tool: click + or -, adjust the volume. (13). Control panel 1 Previous File 2 Previous Frame 3 Backward Play 4 Pause 5 Stop 6 Play 7 Next Frame 8 Next file 32

37 (14). Direction, Latitude and longitude Direction Latitude and longitude Showing and postioning vehicle s driving direction, latitude and longitude. (This function requires the device mode with GPS, and optional G-Mouse) (15). Speed per hour Km/h mile/h knot Set the speed unit under Configuration. (This function requires the device mode with GPS, and optional G-Mouse) 33

38 K. Format the SD card Prior to format the SD card, backup all the important data from the SD card. Q. Under which situation you need to format the SD card? A. The SD card has different storage format compare with your device. For avoid record or read error, format your SD card before insert into device. All the SD card that your purchase require format before use. SD card format can divide into two way: format on recorder or format on PC (1). Format on Recorder Step 1. Press menu button on remote control, and then choose the Format the Hard disk Step 2. Press enter to start formatting. 34

39 Step3. When back to the real time view, the format procedure is finish. (2). Format on PC Step 1. Take out SD card from recorder, insert it into SD card reader, and then insert SD reader to personal computer, click and run CarBox2.exe Step 2. Click format tool get into format tool page, choose the SD card that your need to format, click the format button. Step 4. Windows pop up the menu as follows and ask you to answer Start to Format this device?,please ensure SD card inserted correctly, then press Yes. 35

40 Step 5. The window will pop up show on your screen as below. Ask for starting format SD card, please press the start button. After finished the format, please press close, by the time, please do not close player because the player still keep formatting after the SD card formatted. 36

41 Step 6. Finished format SD card (After finish the SD card format, please remove your SD card from the computer and insert into the slot again. And then you can start to precede the related setup on the Player. After that insert the SD to your recorder, your recorder is ready for recording the footage.) 37

42 L. Restore the SD card Prior to Restore the SD card, backup all the important data from the SD card. Q. Under which situation you need to restore the SD card? A. When you want to use the SD card on other purpose. This procedure will restore the SD card as normal format. Only does this procedure use the SD card in a normal storage device. Step 1. Take out SD card from recorder, insert it into SD card reader, and then insert SD reader to personal computer, click and run CarBox2.exe Step 2. Click format tool, select the SD card that you want to restore, and then press the restore button. 38

43 Step 3. The window pop up as below, ask you Restore this Hard Disk press Yes start restoring. Step 4. The window pop up as below, please choose Quick format, then click Start button 39

44 Step 5. Click Yes to start restoring the SD card Step 6. Click "OK" to finish restore SD card Step 7. After the restoring complete, press OK Then the SD card restore as normal format, capable for other using purpose 40

45 M. Wifi Setting (optional) The software download and installation : (1) Smart phone with Android system go to Google play search for VacronPlayer, install from this website: d=com.fuho.e07 Or you can down load and install APK from here: (2) Smart phone activate WIFI function, click the SSID on search list, the default password as (ID & password both set as default, please reset the device name and password as your requirement) 41

46 (3) Open VacronPlay APP, click and select the device list, click the add button and enter device name, type any device name as you want, set the device channel as channel 4, add all the channel( get start from window 01) 42

47 (4) Real time image Real time recording button 43

48 (5) Remote playback / backup 1. Click and select the device name 2. Choose remote playback or download the file 3. choose the channel for playback 4. enter ok. 44

49 For more information Please go to VACRON official website Made in Taiwan