Alarm Clock Radio with Lightning Dock

Transcription

1 *iphone not included Alarm Clock Radio with Lightning Dock Model Number: AACBL-415 INSTRUCTION MANUAL

2 Remote Control : Turn the unit on or off. 2. SOURCE: (FM Radio, Bluetooth / Docking, or Line In). 3. PROG: Preset stations for FM radio. 4. / : Select the next / preset station. Adjust the time. : In BT/DOCK mode, start or pause play. / : In BT/DOCK mode, skip to previous/next track file. In FM mode, search radio stations manually / automatically. 5. PAIR: In BT mode, activate the pairing function and disconnect the existing paired Bluetooth device. 6. ALARM 1: Set or view the settings for Alarm SLEEP: Set the sleep timer. 8. Vol+ / Vol-: Increase/decrease the volume level. 9. SNOOZE: Repeat the alarm. 10. ALARM 2: Set or view the settings for Alarm DIMMER: Adjust the brightness. 12. CLOCK: Set or display the clock. 13. MUTE: Mute of resume the sound. i

3 Remote Control (Cont.) Remote control battery The remote control comes with a CR2025 3V button cell pre-installed. First time use To activate the battery and use the remote control, pull out the plastic tab that separates the battery from the contacts inside the compartment. Battery replacement If the remote control unit is no longer working even when it is operated near the Alarm Clock, you will need to replace the battery with a new battery of the same type. Push in the tab and pull out the battery tray. Remove the old battery. Insert a fresh CR2025 battery with the (+) marking facing upwards. Then push the battery tray with the battery back into the slot. WARNING! Keep batteries out of reach of children. Swallowing may lead to serious injury or death in as little as 2 hours due to internal burns. If swallowed, go straight to a hospital emergency room. Dispose of used batteries immediately. ii

4 Remote Control (Cont.) Using the remote control The remote control has a range of up to 3 metres from the Alarm Clock. Point the remote control directly towards the sensor at the front of the Alarm Clock. Make sure no obstacles are blocking its path. The remote control will not operate if its path is blocked. Handle the remote control with care. Do not drop, apply shock or step on the remote control. Do not spill water on the unit. Do not use the remote control while simultaneously operating a remote control unit of any another unit, which may result in interference. If the remote control is operated near other products which generate infrared rays, or if other remote control devices using infrared rays are used near the unit, it may operate incorrectly. Conversely, the other products may operate incorrectly. If you do not intend to use the remote control for an extended period of time (more than a month), remove the battery to prevent possible damage from battery leakage and corrosion. Battery precautions Do not use any other battery than specified. Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. Do not carry or store batteries with other metallic objects. Doing so could cause batteries to short-circuit, leak or explode. Do not expose the battery to excessive direct heat such as sunshine, fire or the like. Do not attempt to short-circuit, disassemble or throw batteries into a fire. Never recharge a battery unless it is confirmed to be a rechargeable type. Dispose of batteries promptly and properly, observing any local hazardous waste regulations. Do not burn or bury them. iii

5 Contents Warranty Details 3 Welcome 4 General Safety Instructions 5 Product Overview 8 Getting Started 9 Instructions 10 FAQs 16 Other Useful Information 17 Repair and Refurbished Goods or Parts Notice 18 2

6 Alarm Clock Radio with Lightning Dock Warranty Details The product is guaranteed to be free from defects in workmanship and parts for a period of 12 months from the date of purchase. Defects that occur within this warranty period, under normal use and care, will be repaired, replaced or refunded at our discretion, solely at our option with no charge for parts and labour. The benefits conferred by this warranty are in addition to all rights and remedies in respect of the product that the consumer has under the Competition and Consumer Act 2010 and similar state and territory laws. Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. 3

7 Welcome Congratulations on choosing to buy a BAUHN product. All products brought to you by BAUHN are manufactured to the highest standards of performance and safety and, as part of our philosophy of customer service and satisfaction, are backed by our comprehensive 1 Year Warranty. We hope you will enjoy using your purchase for many years to come. 4

8 General Safety Instructions Read this manual thoroughly before first use, even if you are familiar with this type of product. The safety precautions enclosed herein reduce the risk of fire, electric shock and injury when correctly adhered to. Keep the manual in a safe place for future reference, along with the completed warranty card, purchase receipt and carton. If applicable, pass these instructions on to the next owner of the appliance. Always follow basic safety precautions and accident prevention measures when using an electrical appliance, including the following: Electrical safety and cord handling Voltage: Before plugging in the power adaptor, make sure your outlet voltage and circuit frequency correspond to the voltage stated on the product rating label. Wall socket: Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock. When the adaptor is plugged into the power supply, make sure the wall socket is easily accessible so it can be readily unplugged. Do not immerse: To protect against fire and electric shock, do not immerse the cord, plug, power adaptor or the product itself in water or other liquid. Protect from moisture: Never subject this product to moisture or extreme temperatures. Do not expose it to dripping or splashing water. Do not use the product near water (bathtub, washbowl, kitchen sink, laundry tub, swimming pool) or in a damp basement. Protect the power cord: Do not kink, bend, squash or damage the cord of the power adaptor and protect it from sharp edges and heat. Ensure nothing is placed upon or against the cord. It is always best to have a clear area from where the cord exits the unit to where it is plugged into a wall outlet. Run the cord in such a way that there will be no risk of anyone pulling it inadvertently, tripping over it or stepping on it. Damaged cord: If the electric cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified personnel. Contact our after sales support line in order to avoid a hazard. Disconnect: To prevent damage to the product due to lightning strikes and powerline surges, switch the product off and unplug it from the wall outlet during lightning storms and when the product is not going to be used for an extended period of time. Grip the plug when disconnecting, do not pull the cord. 5

9 General Safety Instructions (Cont.) Usage conditions and restrictions Attachments: Do not use attachments that are not recommended by the product manufacturer or distributor. Adjustments: Only use and adjust controls and perform procedures as specified in this manual. Any other adjustments or procedures may expose you to danger and void your warranty. Installation and use: Improper use or installation may result in the risk of fire, electric shock and/or injury. We assume no liability for any eventual damages caused by improper use or incorrect handling. Usage restriction: This product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the product by a person responsible for their safety. Children: Supervise young children to ensure they do not play with the product. Safe usage Location: Place the product on a straight, rigid and stable surface, away from sources of direct sunlight or excessive heat. Ventilation: The unit should be situated so that its location or position does not interfere with its proper ventilation. For example, do not place it on a bed, sofa, carpet, rug or similar surface that may block the ventilation openings. Do not cover the ventilation openings with items such as newspapers, tablecloths, curtains, etc. Do not place it in a builtin installation, such as a bookcase or cabinet. Do not place anything underneath the product (for example, CDs or magazines). Prevent overheating: Place the product in a sufficiently aerated place, allowing at least 10cm clearance at the back and top of the product, and 5cm on both sides, to prevent overheating. Do not place the product on top of another appliance that may cause overheating (for example, a receiver or amplifier). Keep away from heat: Do not place the product near heat sources such as radiators, heat registers, stoves or other appliances that produce heat. Prevent damage: Do not place the product near other items that may damage it, such as naked flame sources (lit candles) or objects containing water (a vase or fish bowl). Keep openings clear: Take care that no objects fall and no liquids are spilled into any openings or vents. 6

10 General Safety Instructions (Cont.) Care and cleaning Cleaning: Clean the unit only as recommended in this manual, with a dry, soft cloth. Do not use chemical cleaners: Do not use strong cleaning agents, such as benzine, thinner or similar substances as these can damage the surface of the unit. Do not open: Do not remove the cover or the back of this product. There are no user-serviceable parts inside this product. Do not repair yourself: Do not attempt to dismantle, open or repair this product yourself. Do not attempt to service the unit beyond those methods described in this instruction manual. Service methods not covered in the operating instructions should be referred to qualified service personnel. Service: Contact the after sales support line and arrange a service by qualified service personnel in the following circumstances: * The power supply cord or plug of the power adaptor has been damaged. * Objects have fallen into or liquid has been spilled into the enclosure. * The unit has been exposed to rain. * The unit has been dropped or the enclosure damaged. * The unit exhibits a marked change in performance or does not operate normally. Battery disposal: Dispose of spent or damaged batteries in accordance with local regulations. To reduce the risk of electric shock, do not remove the cover (or back). This unit contains no user-serviceable parts inside. Refer all servicing to qualified service personnel only. The lightning flash with an arrowhead symbol within an equilateral triangle is intended to alert you to the presence of non-insulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert you to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. 7

11 Product Overview 1. Dock for ipod/iphone: Connect your Lightning Pin enabled device to pair and charge. 2. : Press this button to turn ON or press and hold to enter Standby mode. When the unit is on, press to change the source. The selected mode will show on the display. 3. : In BT/DOCK mode, start or pause play 4. / : In BT/DOCK mode, skip to previous/next track file. In FM mode, search radio stations manually by pressing once and automatically by holding it for 3 seconds. 5. VOL + / VOL -: Increase/ decrease the volume level. 6. : NFC (Near Field Communication) Sensor 7. Display Panel: Display the Time, FM Station, and other common notifications. 8. DC 5V~ Socket: Connect to the power adapter. 9. LINE IN Socket: Connect to an external audio device 10. FM Antenna Wire 8

12 Getting Started (Cont.) Connecting the Power CAUTION! Risk of product damage! Ensure that the power supply voltage corresponds to the voltage printed on the rating label on the back or the underside of the power adapter. Connect the adapter plug to your power outlet and adapter socket to your Alarm Clock Power ON/OFF When you first connect the unit to the main socket, the unit will be in STANDBY mode. Press the button on the remote control or the button on the main unit to switch the main unit ON. Press the button on the remote control or press and hold the button on the main unit to switch the main unit back to STANDBY mode. NOTE: Disconnect the adaptor plug from the power outlet if you want to switch the unit off completely. All settings will be erased. If there is no signal under the BT (Bluetooth), DOCK (iphone/ipod) and LINE IN mode, the unit will switch off automatically within 15 minutes. Set the Time The built-in clock shows the time in the display. 1. In STANDBY mode, press and hold the CLOCK button on the remote control until the hour indicator starts flashing. 2. Press the / buttons on the remote control to set the hour. Then press the CLOCK button to confirm the hour. The minute indicator will start flashing. 3. Press the / buttons on the remote control to set the minutes. Then press the CLOCK button to confirm the minutes. Your clock will now be set. IMPORTANT: If no button is pressed for 15 seconds, the settings will be lost and you will need to start again. If you are in BT, DOCK, or LINE IN modes and would like to see the time, press CLOCK on the remote and the time will be displayed. Press again to return to the original display. 9

13 Instructions Setting the Alarm You can set two alarms that go off at different times. NOTE: Before setting the alarm, ensure that the clock is set correctly. 1. Press and hold the ALARM [1 or 2] button on remote control in standby mode for a few seconds and the hour digits will flash. 2. Press the / buttons on the remote control to set the required hour. Then press the ALARM [1 or 2] button to confirm the hour. The minute digits will start flashing. 3. Press the / buttons on the remote control to set the required minute. Then press the ALARM [1 or 2] button to confirm the minute. The alarm time will now be set. 4. Press the / buttons on the remote control to select an alarm sound source: ipod/iphone, FM tuner or buzzer. Then press the ALARM [1 or 2] button to confirm. NOTE: If FM mode is chosen, the alarm will play the last played station. 5. Press the / buttons on the remote control to select the required volume, we recommend no less than 5 as a minimum. Then press the ALARM [1 or 2] button to confirm. Your Alarm is now set, and either or will be displayed. Activate and Deactivate the Alarm If an Alarm is set, press the ALARM [1 or 2] button twice on the remote to activate or deactivate the timer. If the alarm is activated or is displayed. If the alarm is deactivated, the or will disappear from the display on the front of the unit. Snooze Alarm When the alarm sounds, you can stop it temporarily by pressing the SNOOZE button. The display will show the SNOOZE indicator and the relative alarm or will be flashing. The alarm will be delayed for 9 minutes and then start again. This manual snooze operation can be repeated again and again. If the alarm is set in FM mode, snoozing will reactivate FM after 9 minutes 10

14 Instructions (Cont.) If the alarm is set in Docking mode, snoozing will reactivate playing music from the device after 9 minutes. Stop Alarm Ring When the alarm rings, press the corresponding ALARM [1 or 2] button. The alarm will stop, but the settings will remain activated so you do not need to keep setting every day. View the Alarm Settings Press the ALARM [1 or 2] button to view the alarm settings. The display will scroll through the date, mode and volume of the set alarm. Setting the Sleep Timer This unit can switch to standby automatically after a set period of time. To activate the Sleep Timer, press the SLEEP button on remote control repeatedly to select a set period of time (in minutes) When the sleep timer is activated, the display will show and the volume will gradually decrease before the unit powers off. To deactivate the Sleep Timer, press the SLEEP button on remote control repeatedly until [00] is displayed. When the sleep timer is deactivated, disappears from the display. Adjust the Display Brightness Press the DIMMER button on remote control repeatedly to select different levels of display brightness. Adjust the Volume During play, press the VOL+/- buttons on the remote control or on the main unit to increase or decrease the volume level. If you wish to turn the sound off, press the MUTE button on the remote control. Press the MUTE button again, or press the VOL+/- buttons on the remote control or main unit to resume normal listening. 11

15 Instructions (Cont.) Radio (FM) Operation Auto Scanning and saving a Preset Station Press the button on the main unit or the FM button on the remote control to select the FM mode. Press and hold the PROG button on the remote control or the button on the unit for a few seconds to activate automatic programming. All available stations are programmed in the order of waveband reception strength. The first programmed radio station is played automatically after the unit has finished scanning for radio stations. Press the / buttons on the remote control to select the preset station you would like to listen to. Tuning in a Station manually Press and hold the / button on the remote control, the frequency will change down or up automatically until a station is found. Continue to press the / button on the remote control until you find the station you want. Storing Stations Manually You can store up to 20 FM stations. 1. Following the steps above, tune in the desired station, then press the PROG button on the remote control. 2. Press the / buttons on the remote control to select the preset number you would like to save to. 3. Press the PROG button on the remote control to store the station. 4. Repeat steps 1 to 3 for each station you would like to store in the preset stations. 12

16 Instructions (Cont.) ipod/iphone Operation You can enjoy audio from ipod/iphone through this unit. Listen to the ipod/iphone NOTE: This unit only supports products with a Lightning Connector. 1. Press the button on the main unit or the BT/DOCK button on the remote control to select the DOCK (iphone/ ipod) mode. 2. Carefully place your iphone/ipod into the docking bay by placing the connecting port on the bottom of the iphone/ipod onto the connector in the docking bay. NOTE: Remember to remove any bumper case before inserting your device onto the docking connector. 3. Follow below instructions to operate this unit: To pause/resume play, press the button on the remote control or on the main unit. To skip to a track, press the / buttons. To fast forward/backward during play, press and hold the / buttons, then release to resume normal play. Charging the ipod/iphone Your ipod/iphone will automatically charge the battery when docked. Bluetooth Operation You can listen to music from a Bluetooth enabled device via this player. 1. Press the button on the main unit or the BT/DOCK button on the remote control to select the BT (Bluetooth) mode. NO BT will show on the display if the unit is not paired to any Bluetooth device, the system has entered pairing mode. Alternately, you can press the PAIR button on the remote control to activate Bluetooth pairing. The word PAIRING will sound from the unit, and PAIR will be shown on the display. 13

17 Instructions (Cont.) 2. Activate Bluetooth on your device, and select the search mode. BAUHN AACBL-415 will appear. Tap on this to establish the Bluetooth conection. 3. When pairing is successful, the unit will sound PAIRED. TIPS: Before you connect a Bluetooth device to this unit, familiarize yourself with the Bluetooth capabilities of your device. Not all devices and functions are compatible with this unit. Enter 0000 for the password if necessary. If a connection already exists, once in BT mode, press the PAIR button on the remote control once to re-activate the pairing. The unit will sound PAIRED indicating a successful pairing. In Pairing Mode, if no Bluetooth device is paired within 2 minutes, the player will recover the previous connection. The operational range between this player and a Bluetooth device is approximately 9 meters. The connection will be disconnected automatically when the device is out of this range and the display will flash NO BT once. To reconnect, place it back within the operational range. the unit will sound PAIRED Any obstacle between this unit and Bluetooth device can reduce the operational range. Keep this player away from any other electronic device that may cause interference. NFC (Near Field Communication) Operation Pair your NFC-enabled mobile device directly with this unit by just a single tap. 1. Activate NFC on your mobile device. 2. Tap and hold your mobile device on the icon of the unit. The first time you are pairing your devices, your mobile device will vibrate or a message will pop up, prompting you to pair the unit with your device. Your mobile NFC sensing area 14

18 Instructions (Cont.) device will then switch to Bluetooth mode. The unit will sound PAIRED and BT will flash once on the display. 3. You can operate playback features via your mobile device. 4. To disconnect your mobile device, tap and hold again on the icon of the unit. The unit will sound DISCONNECTED and NO BT will flash once on the display. NOTE: The NFC function only works with mobile devices that support NFC technology. You may need to remove your mobile device case to connect using NFC. Line in Operation You can listen to an external audio device through this unit. 1. Ensure that the unit is connected to the external or audio device. Connect the 3.5mm audio cable (supplied) to the LINE IN socket on the rear of unit and to the headphone socket on your audio device. 2. Press the button on the main unit or the LINE IN button on the remote control to select the LINE mode. 3. The music playing on your device will automatically start playing on the unit. 4. Press the VOL +/ button on remote control or on main unit to adjust the volume to your desired level. NOTE: Only the volume can be adjusted via the remote control, other functions must be controlled via the settings on your device. 15

19 FAQs No power Symptom Possible Problem and Solution Ensure that the adaptor is connected properly. Ensure that there is power at the AC outlet. Ensure the correct source is selected. Remote control does not work Poor radio reception Sleep timer does not work Clock setting erased I can t find the Bluetooth name of this unit on my Bluetooth device for Bluetooth pairing NFC-enabled mobile device will not pair directly via NFC Reduce the distance between the remote control and the unit. Insert the battery with its polarities (+/-) aligned as indicated. Replace the battery. Aim the remote control directly at the sensor on the front of the unit. Increase the distance between the unit and your TV or VCR. Fully extend the FM antenna. Set FM antenna close to windows if you are using it indoors. Ensure the clock is set correctly. Ensure the timer is set correctly and is activated. Power has been interrupted or the power cord has been disconnected. Reset the clock. Ensure that the unit is switch on. Ensure that the Bluetooth function is activated on your Bluetooth device. Download and Install the App Tap-and-Pair from the Google Play Store ( com). Pair with the unit manually first, then touch and hold again on the NFC sensing area. 16

20 Other Useful Information (Cont.) Specifications AC Power Adaptor Input V ~ 50/60Hz, 0.5A Output DC5.0V 2.0A Speaker Output Power 3W x 2 Audio Input Sensitivity 500mV Frequency Response 40Hz - 20kHz Tuning Range MHz Unit Dimensions (w x h x d) x 57 x 191.6mm Speaker Impedance 2Ω The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc., and any use of such marks by Hands (IP) Holdings Pty Ltd is under license. Other trademarks and trade names are those of their respective owners. The N Mark is a trademark or registered trademark of NFC Forum, Inc. in the United States and in other countries. Lightning, ipod and iphone are a trademark of Apple Inc. 17

21 This page has been left blank intentionally. 18

22 This page has been left blank intentionally. 19

23 This page has been left blank intentionally. 20

24 Alarm Clock Radio with Lightning Dock Repair and Refurbished Goods or Parts Notice Unfortunately, from time to time, faulty products are manufactured which need to be returned to the supplier for repair. Please be aware that if your product is capable of retaining user-generated data (such as files stored on a computer hard drive, telephone numbers stored on a mobile telephone, songs stored on a portable media player, games saved on a games console or files stored on a USB memory stick) during the process of repair, some or all of your stored data may be lost. We recommend you save this data elsewhere prior to sending the product for repair. You should also be aware that rather than repairing goods, we may replace them with refurbished goods of the same type or use refurbished parts in the repair process. Please be assured though, refurbished parts or replacements are only used where they meet ALDI s stringent quality specifications. If at any time you feel your repair is being handled unsatisfactorily, you may escalate your complaint. Please telephone us on or write to us at: Tempo (Aust) Pty Ltd ABN PO BOX 6056 Frenchs Forest, Sydney, Australia NSW 2086 Tempo Help Desk: (Aust) (Operating Hours: Mon-Fri 08:30AM to 06:00PM EST) info@tempo.org