Quick Start Guide. VMware vsphere / vsphere Hypervisor. Compact PC. Server Mode (Single-Interface Deployment) 4th Generation.

Transcription

1 VX VIRTUAL APPLIANCES If you re not using VMware vsphere Client 5.1, your screens may vary. VMware vsphere / vsphere Hypervisor Server Mode (Single-Interface Deployment) 2015 Silver Peak Systems, Inc. Compact PC 4th Generation Before You Begin Review the document, Preparing a Compact PC with VMware vsphere for VXOA ISO Download the virtual appliance OVF template file: - For a 30-day free trial, go to the Silver Peak Marketplace. - If you ve purchased the product, then log in at the Silver Peak Support portal. Obtain a VX virtual appliance activation license key If not using DHCP, then get an IP address for the Silver Peak appliance. This Quick Start Guide only covers the single-interface Server mode, which uses mgmt0 for data traffic. NOTE: When you download the OVF template file and save it, Internet Explorer may change the suffix from.ova to.tar. If it does, change the suffix back to.ova. SUMMARY OF TASKS 1 Configure the Compact PC s BIOS 2 Deploy the VX virtual appliance s OVF template 3 Configure the Resource Allocation Reservation 4 Establish connectivity to the virtual appliance 5 Run the Appliance Manager initial configuration wizard Silver Peak Systems, Inc De La Cruz Blvd. Suite 100 Santa Clara, CA (toll-free in USA) PN Rev A» R6.2 1 of 11

2 VX Virtual Appliance / VMware vsphere / vsphere Hypervisor / Server Mode [Single-Interface Deployment] 1 Compact PC - 4th Gen Configure the Compact PC s BIOS These directions are specific to the Intel NUC. For other compact PCs, consult your Silver Peak Sales Engineer. a. When the Intel NUC screen appears, click F2 to begin the setup. The Intel Visual BIOS screen appears. b. Click Advanced Setup. The following screen appears. c. Click Devices, and then click SATA. Verify that Chipset SATA Mode is AHCI. 2 of 11 PN Rev A» R6.2

3 d. Click Performance. Verify the following: Performance Settings Failsafe Watchdog Unlock Extreme Voltages [selected] [selected] e. Click Power. The primary and secondary power settings appear. PN Rev A» R6.2 3 of 11

4 VX Virtual Appliance / VMware vsphere / vsphere Hypervisor / Server Mode [Single-Interface Deployment] Compact PC - 4th Gen f. Make the following changes: Primary Power Settings Intel Dynamic Power Technology Secondary Power Settings Power Supervisor Shutdown After Power Failure S3 State Indicator Wake on LAN from S4/S5 PCIe ASPM Support Off [deselect] Power On Off Stay Off Disable g. Click F10 for Save and Exit. h. When asked if you want to exit Visual BIOS, click Yes. 4 of 11 PN Rev A» R6.2

5 2 Deploy the VX virtual appliance s OVF template a. Launch the vsphere client, enter the IP address for the VMware vsphere host. The host interface appears. b. From the File menu, select Deploy OVF Template, and follow the steps in the wizard. NOTE: On the Name and Location page, we changed the virtual appliance s default name to MySilverPeak, to make this example more generic. c. On the Disk Format page, make sure to select Thick Provision Lazy Zeroed. PN Rev A» R6.2 5 of 11

6 VX Virtual Appliance / VMware vsphere / vsphere Hypervisor / Server Mode [Single-Interface Deployment] Compact PC - 4th Gen d. When the Ready to Complete page appears, go to the bottom of the page and click Finish. The Silver Peak appliance deploys. 6 of 11 PN Rev A» R6.2

7 3 Configure the Resource Allocation Reservation a. In the vsphere Client, select the newly deployed virtual appliance and click the Summary tab. Click Edit Settings. b. When the Virtual Machine Properties window appears, select CPUs. c. Click the Resources tab. PN Rev A» R6.2 7 of 11

8 VX Virtual Appliance / VMware vsphere / vsphere Hypervisor / Server Mode [Single-Interface Deployment] Compact PC - 4th Gen d. Set Reservation to 0 MHz. Click OK. The window closes. 8 of 11 PN Rev A» R6.2

9 4 Establish connectivity to the virtual appliance a. In the vsphere Client, select the newly deployed virtual appliance and click the green arrow to power on. b. Click the Console tab. The Silver Peak Console User Interface appears. c. The next task is to determine the virtual appliance s IP address: If you re using DHCP, the virtual appliance IP address displays in Silver Peak s Console User Interface. PN Rev A» R6.2 9 of 11

10 VX Virtual Appliance / VMware vsphere / vsphere Hypervisor / Server Mode [Single-Interface Deployment] Compact PC - 4th Gen If you re not using DHCP, then you must configure the static IP address and default gateway. In the virtual appliance console, press function key, F4, and complete the remaining steps. When prompted to choose the type of management interface, select Static (as opposed to DHCP). After selecting Apply, you can review the settings by selecting function key, F2. d. To verify connectivity, press function key, F1, and enter the following command sequence: [vx-appliance] > enable [vx-appliance] # show ip default-gateway [vx-appliance] # ping <default-gateway> [ENTER] [ENTER] [ENTER] To stop the pinging, enter CTRL-C. You are now ready to complete the Silver Peak virtual appliance initial configuration wizard. 10 of 11 PN Rev A» R6.2

11 5 Run the Appliance Manager initial configuration wizard a. In a browser, enter the IP address that you just discovered or configured. The Silver Peak Appliance Management Console login page appears. b. For both the User Name and Password, enter admin. The initial configuration wizard appears. c. Complete the remaining wizard screens. d. On the last wizard screen, click Apply. When the virtual appliance asks permission to reboot, allow it. The Appliance Manager takes a few minutes to reboot and return to the login page. You are now ready to start using the appliance. PN Rev A» R of 11