5AA USER'S MANUAL. Support Intel Pentium, MMX, Cyrix/IBM 6x86MX, MII, AMD K6, K6-2, K6-III, IDT Winchip 2, IDT Winchip 3 & RISE MP6 CPUs.

Transcription

1 AA USER'S MANUAL Support Intel Pentium, MMX, Cyrix/IBM xmx, MII, AMD K, K-, K-III, IDT Winchip, IDT Winchip & RISE MP CPUs. Support parity check or ECC function. Support fully AGP.0 specification. Support itching mode voltage regulator on board (.V~.V). Support ///9 MHz and 00MHz. Support Modem Ring On (COMA AB), Win 9/9 shutdown. Support Wake on Lan (The ATX power supply supports larger than 0 ma V Stand-By current ). Support keyboard power on function (The ATX power supply supports larger than 00mA V Stand-by current). Support Ultra DMA and ATA. Support IrDA function for Fast IrDA. Pentium Processor PCI - ISA BUS MAINBOARD REV.. First Edition R

2

3 AA The author assumes no responsibility for any errors or omissions which may appear in this document nor does it make a commitment to update the information contained herein. THIRD-PARTY BRANDS AND NAMES ARE THE PROPERTY OF THEIR RESPECTIVE OWNERS. Dec., 999 Taipei, Taiwan

4 Quick Installation Guide I. CPU Jumper Setting Table: O: ON X: OFF SW SW.V X X X X O.V O X O X X.V X O X X O.V X O O X X.V X X O X O.V O O O X X.V X O O X O.V X X X O X.V X X X O O.9V O X X O X.V X O X O O.0V X O X O X.9V X X O O O.V O O X O X.0V X O O O O.V X X O O X.V O X X X X.V O X O O X.V X O X X X.V X O O O X.V O O X X X.V O O O O X.V X X O X X SW X. X X X X O X X X. O O X X X O X X. X X X X O X O X. O O O X X O O X. X X O X O X X

5 AA JP JP JP JP MHz X M O M X M O 9M X 00M X 0M O 0M X M O 0M X M O 0M X M O 0M Note: It s strongly recommended that set the system speed according to your hardware configuration: CPU, SDRAM, Cards, etc.

6 Quick Installation Guide II. Quick Installation Guide: O : ON X : OFF CPU S S S S S S S S JP JP JP JP. Pentium MHz O X X O O O O X X. Pentium MHz O O X O O O O X X. Pentium 00 MHz X O X O O O O X X. Intel MMX-MHz O O X X X X O X X. Intel MMX-00MHz X O X X X X O X X. Intel MMX-MHz X X X X X X O X X. AMD-K/ (.9V) O O X O X X O X X. AMD-K/00 (.9V) X O X O X X O X X 9. AMD-K/ (.V) X X X X X O O X X 0. AMD-K/ (*..V) X X X X O X X X X. AMD-K/ (*.V) AMD-K-/ (*.V) O X O X O X X X X. AMD-K/00 (*..V) O O O X O X X X X. AMD-K/00 (00*.V) AMD-K-/00 (00*.V) X O X X O X X X X. AMD-K-/ (*.V) X O O X O X X X X. AMD-K-/ (9*..V) X X X X O X X X O. AMD-K-/0 (00*..V) X X X X O X X X X.AMD-K-/ (*..V) * X X O X O X X X X. AMD-K-/0 (9*.V) O X O X O X X X O 9. AMD-K-/00 (00*.V) O X O X O X X X X 0. AMD-K-/0 (00*..V) * O O O X O X X X X. AMD-K-/0 (00*..V) O O O X X O X X X. AMD-K-/ (9*.V) * X O O X O X X X O. AMD-K-/ (9*.V) * X O O X X O X X O. AMD-K-/00 (00*.V) * X O O X O X X X X. AMD-K-/00 (00*.V) * X O O X X O X X X

7 AA. AMD-K-/0 (00*..V) * X X O X O X X X X. AMD-K-III/00 (00*.V) * O X O X O X X X X CPU S S S S S S S S JP JP JP JP. AMD-K-III/00 (00*.V) O X O X X O X X X 9.AMD-K-III/0 (00*..V) * 0.AMD-K-III/0 (00*..V) * O O O X O X X X X O O O X X O X X X. AMD-K-III/ (9*.V) * X O O X O X X X O. AMD-K-III/ (9*.V) * X O O X X O X X O. AMD-K-III/00 (00*.V) * X O O X O X X X X. AMD-K-III/00 (00*.V) * X O O X X O X X X. AMD-K-III/0 (00*..V) *. Cyrix/IBM xmx-pr (*.9V). Cyrix/IBM xmx-pr00 (*..9V). Cyrix/IBM xmx-pr00 (*.9V) 9. Cyrix/IBM xmx-pr (*.9V) 0. Cyrix/IBM xmx-pr (*..9V). Cyrix/IBM xmx-pr (*.9V). Cyrix/IBM xmx-pr (*..9V). Cyrix/IBM xmx-pr (*.9V). Cyrix/IBM xmx-pr (*..9V). Cyrix M -PR00 (*..9V). Cyrix M -PR (*.9V). Cyrix M -PR (*.9V) X O O X O X X X X O X X O X X O X X O O X O X X O X X O X X O X X O X O X O X O X X O X X O O X O X X O X O O X X O X X O X X X X X O X X O X X X O X O X X O X O O O X O X X O X X X X X O X X O X X O X O O X X O X X X O X O X X O X X

8 Quick Installation Guide. Cyrix M -PR (*..9V) 9. Cyrix M -PR * (00*..9V) 0. Cyrix M -PR * (*.9V) X X X O X X O X O O O X O X X O X X O X O O X X O X O CPU S S S S S S S S JP JP JP JP. Cyrix M -PR (*..9V) * X X X O X X O X X. Cyrix M -PR00 (00*..9V) * X X X O X X O X X. IDT Winchip -00 (*.V). IDT Winchip -00 * (00*.V). IDT Winchip - (*.V). IDT Winchip - * (*..V). IDT Winchip - * (00*..V). IDT Winchip - * (*.V) 9. IDT Winchip - * (00*..V) 0. IDT Winchip -00 * (00*..V). IDT Winchip - * (00*..V). RISE MP- * (00*.V) X O X O O O O X X O X X O O O O X X X O X O O O O X O X X X O O O O X X X O O O O O O X X O X O O O O O X X X X O O O O O X X O O X O O O O X X X O O X X X O X X O X X X X X O X X Note: If Cyrix x is being used, please check the CPU Date Code after 0. The default setting is 00* at.v for AMD K/00 and AMD K-/00 CPU S S S S S S S S JP JP JP JP AMD-K/00 (00*.V) AMD-K-/00 (00*.V) X O X X O X X X X The settings of the processors marked with * above are just for your reference, these processors have not been tested yet!

9 AA. Pentium Processor MHz SW CPU JP SW AA M MC JPJPJP. Pentium Processor MHz JP JP JP JP. Pentium Processor 00 MHz JP JP JP JP

10 Quick Installation Guide. Intel MMX- MHz JP JP JP. Intel MMX-00 MHz JP JP JP JP JP. Intel MMX- MHz JP JP JP JP. AMD-K/ (.9V) JP JP JP JP. AMD-K/00 (.9V)

11 AA JP JP JP JP 9. AMD-K/ (.V) JP JP JP JP 0. AMD-K/ (*..V) JP JP JP JP. AMD-K/ (*.V); AMD-K-/ (*.V) JP JP JP JP. AMD-K/00 (*..V) JP JP JP JP. AMD-K/00 (00*.V); AMD-K-/00 (00*.V) 9

12 Quick Installation Guide JP JP JP JP. AMD-K-/ (*.V) JP JP JP JP. AMD-K-/ (9*..V) JP JP JP JP. AMD-K-/0 (00*..V) JP JP JP JP. AMD-K-/ (*..V) JP JP JP JP 0

13 AA. AMD-K-/0 (9*.V) JP JP JP JP 9. AMD-K-/00 (00*.V) JP JP JP JP 0. AMD-K-/0 (00*..V) JP JP JP JP. AMD-K-/0 (00*..V) JP JP JP JP. AMD-K-/ (9*.V) JP JP JP JP

14 Quick Installation Guide. AMD-K-/ (9*.V) JP JP JP JP. AMD-K-/00 (00*.V) JP JP JP JP. AMD-K-/00 (00*.V) JP JP JP JP. AMD-K-/0 (00*..V) JP JP JP JP. AMD-K-III/00 (00*.V) JP JP JP JP

15 AA. AMD-K-III/00 (00*.V) JP JP JP JP 9. AMD-K-III/0 (00*..V) JP JP JP JP 0. AMD-K-III/0 (00*..V) JP JP JP JP. AMD-K-III/ (9*.V) JP JP JP JP. AMD-K-III/ (9*.V) JP JP JP JP

16 Quick Installation Guide. AMD-K-III/00 (00*.V) JP JP JP JP. AMD-K-III/00 (00*.V) JP JP JP JP. AMD-K-III/0 (00*..V) JP JP JP JP. Cyrix /IBM xmx-pr (*.9V) JP JP JP JP. Cyrix /IBM xmx-pr00 (*..9V)

17 AA JP JP JP JP. Cyrix /IBM xmx-pr00 (*.9V) JP JP JP JP 9. Cyrix /IBM xmx-pr (*.9V) JP JP JP JP 0. Cyrix /IBM xmx-pr (*..9V) JP JP JP JP. Cyrix /IBM xmx-pr (*.9V) JP JP JP JP. Cyrix /IBM xmx-pr (*..9V)

18 Quick Installation Guide JP JP JP JP. Cyrix / IBM xmx-pr (*.9V) JP JP JP JP. Cyrix / IBM xmx-pr (*..9V) JP JP JP JP. Cyrix MII-PR00 (*..9V) JP JP JP JP. Cyrix MII-PR (*.9V) JP JP JP JP. Cyrix M -PR (*.9V)

19 AA JP JP JP JP. Cyrix M -PR (*..9V) JP JP JP JP 9. Cyrix MII-PR (00*..9V) JP JP JP JP 0. Cyrix MII-PR (*.9V) JP JP JP JP. Cyrix MII-PR (*..9V) JP JP JP JP. Cyrix MII-PR00 (00*..9V)

20 Quick Installation Guide JP JP JP JP. IDT Winchip -00 (*.V) JP JP JP JP. IDT Winchip -00 (00*.V) JP JP JP JP. IDT Winchip - (*.V) JP JP JP JP. IDT Winchip - (*..V) JP JP JP JP. IDT Winchip - (00*..V)

21 AA JP JP JP JP. IDT Winchip - (*.V) JP JP JP JP 9. IDT Winchip - (00*..V) JP JP JP JP 0. IDT Winchip -00 (00*..V) JP JP JP JP. IDT Winchip - (00*..V) JP JP JP JP. RISE MP- (00*.V) 9

22 Quick Installation Guide JP JP JP JP III. Quick Installation Guide of Jumper setting: PWR : Power LED Connector Pin No. Function VCC SW GND GND NC NC AA MC CPU M SPK : Speaker Connector 0

23 AA Pin No. Function VCC SW NC NC Signal AA MC CPU M TD : Turbo LED Connector Pin No. Function LED anode (+) SW LED cathode( ) MC AA CPU M TB : Turbo Switch Connector

24 Quick Installation Guide Pin No. Function Signal SW GND MC AA CPU M RST : Reset Switch Open : Normal operation SW MC Close : Reset system AA CPU M GD : Green LED

25 AA Pin No. Function LED anode (+) SW LED cathode( ) MC AA CPU M GN : Green Function Switch Open : Normal operation SW MC Close : Entering Green Mode AA CPU M HD : IDE Hard Disk Active LED

26 Quick Installation Guide Pin No. Function LED anode (+) SW LED cathode( ) LED cathode( ) LED anode (+) AA MC CPU M Soft PWR : Soft Power Connector Open: Normal Operation SW Short: Power On/Off AA MC CPU M JP: Wake On Lan

27 AA MC SW Pin No. Function +V GND AA Signal CPU M JP: Keyboard Power On (for ATX Power Supply only) SW - Close : Enable Keyboard Power On AA MC M CPU - Close : Disable Keyboard Power On IDE: Primary IDE Port

28 Quick Installation Guide MC SW AA CPU M IDE: Secondary IDE Port MC SW AA CPU M FLOPPY : Floppy Port

29 AA MC SW AA CPU M LPT : LPT Port MC SW AA CPU M COM A : COM A Port

30 Quick Installation Guide MC SW AA CPU M COM B: COM B Port MC SW AA CPU M USB : USB Port

31 AA SW Pin No. Function VCC USB D0 USB D0+ GND VCC CPU USB D USB D+ GND AA M MC JP9 : PS/ Mouse Connector MC SW AA CPU M RED LINE JP9- : PS / Mouse Connector (Optional) 9

32 Quick Installation Guide MC SW PS / MOUSE Pin No. Function Key Data NC GND VCC (+V) Key Clock NC CPU AA M JP0 : AT Keyboard Connector MC SW Keyboard Pin No. Function Key Clock Key Data CPU NC GND VCC AA M JP0- : PS/ Keyboard Connector (Optional) 0

33 AA MC SW Keyboard Pin No. Function Key Data NC GND VCC (+V) Key Clock NC CPU AA M JP : AT Power Connector Pin No. Function Power Good SW,0,, VCC +V V,,, GND 9 V AA MC CPU M J : ATX Power Connector

34 Quick Installation Guide SW Pin No. Function,,,, - GND,,.V,,9,0 VCC (+V) 0 +V V AA V Power Good 9 V SB (Stand by +V) CPU M MC PS-ON (Soft ON/OFF) JP:CPU Cooling Fan Power Connector Pin No. Function SW GND +V Signal AA MC CPU M

35 AA JP : Infrared Connector (Support FIR) Pin No. SW Function Power + FIR IR Data Input AA GND IR Data Output Over Current CPU M MC BAT : For Battery MC + SW AA CPU M Danger of explosion if battery is incorrectly replaced.

36 Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer s instructions. Quick Installation Guide III. Top Performance Test Setting: Users have to modify the value for each item in chipset features as follow for top performance setting.

37 AA ** Each value of items as above depends on your hardware configuration : CPU, SDRAM, Cards, etc. Please modify each value of items If your system does not work properly.

38 Quick Installation Guide PERFORMANCE LIST The following list of performance data is the testing results of some popular benchmark testing programs. These data are just referred by users, and there is no responsibility for different testing data values gotten by users. (The different Hardware & Software configuration will result in different benchmark testing results.) CPU DRAM CACHE SIZE DISPLAY STORAGE O.S. DRIVER AMD K- 00, AMD K-III 0, AMD K-+/0 ( ) MB SDRAM (HYUNDAI HYV00A TC-0S) KB GA-0 (MB SDRAM) Onboard IDE (Quantum KA00AT) Windows NT.0+ SPK Display Driver at 0 x x colors x Hz. Bus Master IDE Driver Processor Winbench9 CPU mark AMD K-/00 (00x) AMD K-III/0 (00x.) AMD K-+/0 (00x. )... FPU Winmark Business Disk Hi-End Disk Business Graphics 0 90 Hi-End Graphics 9 Winstone9 Business. 0. Hi-End..

39 Table Of Contents TABLE OF CONTENTS. INTRODUCTION.. PREFACE KEY FEATURES PERFORMANCE LIST BLOCK DIAGRAM INTRODUCE THE PCI - BUS FEATURES What is AGP SPECIFICATION.. HARDWARE SOFTWARE ENVIRONMENT HARDWARE INSTALLATION.. UNPACKING MAINBOARD LAYOUT QUICK REFERENCE FOR JUMPERS & CONNECTORS SRAM INSTALLATION DRAM INSTALLATION DRAM INSTALLATION CPU INSTALLATION AND JUMPERS SETUP CMOS RTC & ISA CFG CMOS SRAM SPEAKER CONNECTOR INSTALLATION ACPI LED CONNECTOR INSTALLATION HARDWARE RESET SWITCH CONNECTOR INSTALLATION.-

40 AA.. GREEN FUNCTION INSTALLATION PERIPHERAL DEVICE INSTALLATION BIOS CONFIGURATION.. ENTERING SETUP CONTROL KEYS GETTING HELP Main Menu Status Page Setup Menu / Option Page Setup Menu THE MAIN MENU STANDARD CMOS SETUP MENU BIOS FEATURES SETUP CHIPSET FEATURES SETUP POWER MANAGEMENT SETUP PNP/PCI CONFIGURATION LOAD BIOS DEFAULTS LOAD SETUP DEFAULTS INTEGRATED PERIPHERALS SUPERVISOR / USER PASSWORD IDE HDD AUTO DETECTION SAVE & EXIT SETUP EXIT WITHOUT SAVING... - A.Trobuleshooting... -

41 Introduction. INTRODUCTION.. PREFACE Welcome to use the AA motherboard. The motherboard is a Pipeline KB CACHE Pentium Processor based PC / AT compatible system with ISA bus and PCI Local Bus, and has been designed to be the fastest PC / AT system. There are some new features allow you to operate the system with the performance you want. This manual also explains how to install the motherboard for operation, and how to set up your CMOS CONFIGURATION with BIOS SETUP program... KEY FEATURES Pentium Processor based PC / AT compatible mainboard with PCI / ISA / AGP Bus. PCI Bus slots, ISA Bus slots, AGP slot. Supports : Pentium Processor ://00 MHz; MMX ( / 00 / ) AMD :K-( / 00 / / / 00) K-( / 00 / / 0 / / 0 / 00 / 0 / / 00 / 0 ) K-III(00 / 0 / / 00 / 0) Cyrix/IBM :xmx (PR / PR00 / PR / PR) ; M -PR00 / PR / PR / PR00 IDT :Winchip -(00 / / / / 00) Winchip -() RISE :MP-() Supports true bits CACHE and DRAM access mode. Supports Pins (Socket ) ZIF white socket on board. Supports KB Pipeline Burst Sync. nd Level Cache. CPU L / L Write-Back cache operation. Supports ~ MB DRAM memory on board. -

42 AA Supports * pin / Bit DIMM module. Supports -channel Enhanced PCI IDE ports for IDE Devices. Supports *COM (0), *LPT (EPP / ECP), *.MB Floppy port. Supports Green function, Plug & Play function. Licensed AMI BIOS, FLASH ROM for BIOS update. cm*cm, Baby AT Form factor. Supports USB port & PS/ Mouse and Keyboard port. Supports Keyboard Power On. Support Ultra DMA and ATA. Support IrDA function for Fast IrDA. -

43 Introduction.. PERFORMANCE LIST The following list of performance data is the testing results of some popular benchmark testing programs. These data are just referred by users, and there is no responsibility for different testing data values gotten by users. (The different Hardware & Software configuration will result in different benchmark testing results.) CPU DRAM CACHE SIZE DISPLAY STORAGE O.S. DRIVER AMD K- 00, AMD K-III 0, AMD K-+/0 ( ) MB SDRAM (HYUNDAI HYV00A TC-0S) KB GA-0 (MB SDRAM) Onboard IDE (Quantum KA00AT) Windows NT.0+ SPK Display Driver at 0 x x colors x Hz. Bus Master IDE Driver Processor Winbench9 CPU mark AMD K-/00 (00x) AMD K-III/0 (00x.) AMD K-+/0 (00x. )... FPU Winmark Business Disk Hi-End Disk Business Graphics 0 90 Hi-End Graphics 9 Winstone9 Business. 0. Hi-End.. -

44 AA.. BLOCK DIAGRAM 00MHz 00MHz PBSRAM CPU Host Host Data 00MHz MD Bus MHz 00MHz MHz MA Bus DRAM MHz AGP DEVICE MHz M 00MHz PCI Device ICS9 AF-.Hz MHz.Hz PCI Bus USB GPIO PCI Device PCI Device MHz MHz MC MHz PS/ Keyboard Mouse IR IDE DEVICE ISA Device COMA LPT FDD ISA Bus COMB.MH ISA Device -

45 Introduction.. INTRODUCE THE PCI - BUS Connecting devices to a CPU local bus can dramatically increase the speed of I/Obound peripherals with only a slight increase in cost over traditional systems. This price / Performance point has created a vast market potential for local bus products. The main barrier to this market has been the lack of an accepted standard for local bus peripherals. Many mainboard and chipset manufactures developed their own local bus implementations, but they are incompatible with each other. The VL (Video Electronics Standards Association) local bus and PCI (Peripheral Component Interconnect) bus specification was created to end this confusion. The PCI - bus standard, under development since Jun. 99, which is designed to bring workstation-level performance to standard PC platform. The PCI - bus removes many of the bottlenecks that have hampered PC for several years. On the PCI - bus, peripherals operate at the native speed of the computer system, thus enabling data transfer between peripherals and the system at maximum speed. This performance is critical for bandwidth-constrained devices such as video, multimedia, mass storage, and networking adapters. PCI - bus standard provides end-users with a low-cost, extendible and portable local bus design, which will allow system and peripherals from different manufactures to work together... FEATURES bits bus transfer mode. Bus Master or Slave access. Memory burst transfer to MB/sec. MHz operation speed. 0 device loading ability. CPU independent. -

46 AA.. What is AGP The Accelerated Graphics Port (AGP) is a new port on the Host-To-PCI bridge device that supports graphics display interface. The main purpose of the AGP port is to provide fast access to system memory. The AGP port can be used either as fast PCI port (-bits at MHz vs. -bits at MHz) or as an AGP port which supports x data-rate, a read queue, and side band addressing. When the x-data rate is used the port can transmit data at Mb/sec (.**). The read-queue can be used to pipeline reads removing the effects of the reads-latency. Side band addressing can be used to transmit the data address on a separate line in order to further speed the transaction. -

47 Specification. SPECIFICATION.. HARDWARE CPU COPROCESSOR SPEED DRAM MEMORY CACHE MEMORY I/O BUS SLOTS Pentium Processor / / 00 MHz ; MMX( / 00 / ) AMD K ( / 00 / / / 00) K- ( / 00 / / 0 / / 0 / 00 / 0 / / 00 / 0) K-III (00 / 0 / / 00 / 0) Cyrix / IBM xmx (PR / PR00 / PR / PR) M -PR00 / PR / PR / PR00 IDT Winchip -(00 / / / / 00) Winchip -() RISE MP-() pins (socket ) ZIF white socket on board..v-.v Dual Power Ready. Included in processor. / / / 9 /00MHz system speed. MHz AGP-Bus speed. MHz PCI-Bus speed. MHz AT bus speed. banks pins DIMM module socket on board. Use / / / / MB 0~0 ns DIMM module DRAM. ~ MB DRAM size. Supports.V SDRAM / EDO type DRAM. Supports ECC or Non-ECC type DRAM. / / / KB Lcache included in CPU. KB nd Level cache on board. Supports Write Back cache function for both CPU & on board cache. xmaster / Slave PCI-BUS Slots. x bits ISA BUS Slots. xagp Slot. -

48 AA IDE PORTS -channel Enhanced IDE port on board.(using IRQ,) Supports Mode, IDE & ATAPI CD ROM. Supports Ultra DMA and ATA. I/O PORTS Supports x0 COM ports. (Using IRQ, ) Supports x SPP/EPP/ECP LPT port. (Using IRQ or and DMA or ) Supports x./. MB Floppy port. (Using DMA & IRQ) Supports PS/ Mouse. (Using IRQ ) IrDA connector for Fast IrDA GREEN FUNCTION Suspend mode support. Green itch. IDE & Display power down support. Monitor all IRQ / DMA / Display / I/O events. BIOS Mbit FLASH ROM. Supports Plug & Play Function. DIMENSION Baby AT Form Factor, layers PCB... SOFTWARE BIOS O.S... ENVIRONMENT Licensed AMI BIOS. AT CMOS Setup, BIOS / Chipset Setup, Green Setup, Hard Disk Utility included. Operation with MS-DOS, Windows 9, Windows 9, WINDOWS NT, OS/, NOVELL and SCO UNIX. Ambient Temp. 0 C to +0 C (Operating). Relative Hum. 0 to +% (Operating). Altitude 0 to 0,000 feet (Operating). Vibration 0 to,000 Hz. Electricity.9 V to. V. Max. 0A current at V. -

49 Hardware Installation. HARDWARE INSTALLATION.. UNPACKING The mainboard package should contain the following: The AA mainboard. USER S MANUAL for mainboard. Cable set for IDE BFloppy BI/O Port & PS/ mouse (Optional). CD for Mainboard Drivers and Utilities. The mainboard contains sensitive electric components which can be easily damaged by static electricity, so the mainboard should be left in its original packing until it is installed. Unpacking and installation should be done on a grounded anti-static mat. The operator should be wearing an anti static wristband, grounded at the same point as the anti-static mat. Inspect the mainboard carton for obvious damage. Shipping and handling may cause damage to your board. Be sure there are no shipping and handling damage on the board before proceeding. After opening the mainboard carton, extract the system board and place it only on a grounded anti-static surface component side up. Again inspect the board for damage. Press down on all of the socket IC s to make sure that they are properly seated. Do this only on with the board placed on a firm flat surface. DO NOT APPLY POWER TO THE BOARD IF IT HAS BEEN DAMAGED. It is assumed that the chassis is designed for a standard AT mainboard mounting. Place the chassis on the anti-static mat and remove the cover. Take the plastic clips, Nylon stand-off and screws for mounting the system board, and keep them separate. -

50 AA.. MAINBOARD LAYOUT PW TD GD RST SOFT HD ISA ISA JP WAKE ON LAN BAT BIOS PCI PCI MC SW PCI AGP AA FAN PWR CPU BANK BANK M JP JP JP IDE LPT POWER COM A COM B USB PS/ Mouse KB BANK 0 JP Figure. Optional : PW TD GD RST SOFT HD ISA ISA JP WAKE ON LAN BAT BIOS PCI PCI MC SW PCI AGP AA FAN PWR CPU M JP JP JP IDE FLOPPY LPT COM A COM B USB BANK BANK POWER KB BANK 0 JP Figure. -

51 Hardware Installation.. QUICK REFERENCE FOR JUMPERS & CONNECTORS I/O Port Connectors IDE IDE FLOPPY USB Primary IDE Port. Secondary IDE Port. Floppy Port. USB Port. COM B Serial Port (COM B) COM A LPT PS/ Keyboard Power ATX PWR Serial Port (COM A). LPT Port. PS/ Mouse & Keyboard Connector. Keyboard Connector. AT Power Connector. ATX Power Connector. PW : Power On LED ( PW-LED) Pin No. Function VCC GND GND NC NC SPK : Speaker Connector Pin No. Function VCC NC. NC. Signal TD : Turbo LED Connector Pin No. Function LED POWER (+) LED POWER ( ) -

52 AA TB : Turbo Switch Connector Pin No. Function Signal GND RST : Reset Switch Open Normal operation Close Reset system GD : Green LED Connector Pin No. Function LED anode (+) LED cathode ( ) GN : Green Switch Open Normal operation Close Enter Green Mode HD : Hard Disk Active LED (HD-LED) Pin No. Function LED anode (+) LED cathode ( ) LED cathode ( ) LED anode (+) Soft PWR : Soft Power Switch Open Normal operation Close Power On/Off JP: Wake On Lan Pin No. Function +V SB GND Signal -

53 Hardware Installation FAN Power : CPU Cooling FAN Power Connector Pin No. Function GND +V Signal JP: Keyboard Power On Connector Pin No. Function, Close Enabled Keyboard power on., Close Disabled Keyboard power on. JP: Infrared Connector Pin No. Function Power + FIR IR Data Input GND IR Data Output Over Current.. SRAM INSTALLATION Sync. SRAM (Pipeline Burst SRAM) If Sync SRAM Chip is installed, it consists of Pipeline Burst Pc K x KByte... DRAM INSTALLATION The mainboard can be installed with / / / / MB pins DIMM module DRAM, and the DRAM speed must be ~00 MHz for SDRAM. The DRAM memory system on mainboard consists of bank 0, & bank. Because the pins DIMM module is bits width, using PCS which can match a bits system. The total memory size is MB ~ MB DRAM. The DRAM installation position refer to Figure., and notice the Pin of DIMM module must match with the Pin of DIMM socket. Insert the DRAM DIMM module into the DIMM -

54 AA socket at Vertical angle. If there is a wrong direction of Pin, the DRAM DIMM module couldn't be inserted into socket completely... CPU INSTALLATION AND JUMPERS SETUP The system speed depends on the frequency of CLOCK GENERATOR. The user can change SW selection to set up the system speed to / / /9 00MHz for.v/.v Pentium Processor ( / / 00 MHz) ;MMX( / 00 / MHZ), AMD K-( / 00 / / / 00 ; K-( / 00 / / 0 / / 0 / 00 / 0 / / 00 / 0) ; K-III(00 / 0 / / 00 / 0), Cyrix / IBM xmx (PR / PR00 / PR / PR ) ; M - PR00 / PR / PR / PR00 ; IDT Winchip -(00 / / / / 00) ; IDT Winchip -() ; RISE MP-(). The mainboard can use Pentium Processor, MMX, AMD-K, AMD-K-, AMD-K- III, Cyrix / IBM xmx, Cyrix M, IDT Winchip, IDT Winchip, RISE MP CPU, and the CPU speed must match with the frequency of CLOCK GEN. It will cause system hanging up if the CLOCK GEN.'S frequency is faster than CPU's. The CPU is a sensitive electric component and it can be easily damaged by static electricity, so users must keep it away from metal surface when the CPU is installed onto mainboard. When the user installs the CPU on socket, please notice that the PIN of CPU is in the same corner as the PIN of socket! Before the CPU is installed, the mainboard must be placed on a flat plane in order to avoid being broken by the pressure of CPU installation. O: ON X: OFF SW SW.V X X X X O.V O X O X X.V X O X X O.V X O O X X.V X X O X O.V O O O X X.V X O O X O.V X X X O X.V X X X O O.9V O X X O X.V X O X O O.0V X O X O X.9V X X O O O.V O O X O X.0V X O O O O.V X X O O X.V O X X X X.V O X O O X.V X O X X X.V X O O O X.V O O X X X.V O O O O X.V X X O X X

55 Hardware Installation SW X. X X X X O X X X. O O X X X O X X. X X X X O X O X. O O O X X O O X. X X O X O X X JP JP JP JP MHz X M O M X M O 9M X 00M X 0M O 0M X M O 0M X M O 0M X M O 0M Note: It s strongly recommended that set the system speed according to your hardware configuration: CPU, SDRAM, Cards, etc. Note: If Cyrix x is being used, please check the CPU Date Code after 0... CMOS RTC & ISA CFG CMOS SRAM Built-in Real Time Clock (RTC) With B CMOS SRAM in M9... SPEAKER CONNECTOR INSTALLATION There is a speaker in AT system for sound purpose. The - Pins connector SPK is -

56 AA used to connect speaker. The speaker can work well in both direction of connector when it is installed to the connector SPK on mainboard..9. ACPI LED CONNECTOR INSTALLATION This mainboard uses the existing power LED as ACPI LED.The ACPI LED will light on when system is power-on.the ACPI LED is off when the system is power-off. The ACPI LED will blink when system is in Green mode.this connector should be installed to ACPI LED jumper of the mainboard in correct direction..0. HARDWARE RESET SWITCH CONNECTOR INSTALLATION The RESET itch on panel provides users with HARDWARE RESET function which is almost the same as power-on/off. The system will do a cold start after the RESET itch is pushed and released by user. The RESET itch is a PIN connector and should be installed to RES on mainboard... GREEN FUNCTION INSTALLATION There is one jumper for the purpose of power saving, GN, to indicate the power saving function. This mainboard uses the existing power LED as ACPI LED. If the ACPI LED is blinking, the system is in green mode. The GN itch will force the system into green mode... PERIPHERAL DEVICE INSTALLATION After installation of the device and setup of the jumpers, the mainboard can be mounted into the case and fixed by screw. To complete the mainboard installation, the peripheral devices could be installed now. The basic system needs a display interface card and a storage device. If a PCI - Bus device is to be installed in the system, any one of three PCI - Bus slots can be used for Slave or Master PCI - Bus device. After installing the peripheral device, the user should check everything again and prepare to power-on the system. -

57 AX D-

58 BIOS Configuration. BIOS CONFIGURATION AMI's BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off... ENTERING SETUP Power ON the computer and press <Del> immediately will allow you to enter Setup. The other way to enter Setup is to power on the computer, when the below message appears briefly at the bottom of the screen during the POST (Power On Self Test), press <Del> Key or simultaneously press <Ctrl>, <Alt>, and <Esc> keys. Press DEL to enter SETUP. If the message disappears before you respond and you still wish to enter Setup, restart the system to try again by turning it OFF then ON or pressing the "RESET" bottom on the system case. You may also restart by simultaneously press <Ctrl>,<Alt>, and <Del> keys. -

59 AA.. CONTROL KEYS Up arrow Down arrow Left arrow Right arrow Esc key PgUp key /+ PgDn key / F key F key F key F key F key F key F key F key F9 key F0 key Move to previous item. Move to next item. Move to the item in the left hand. Move to the item in the right hand. Main Menu - Quit and not save changes into CMOS Status Page Setup Menu and Option Page Setup Menu - Exit current page and return to Main Menu. Increase the numeric value or make changes. Decrease the numeric value or make changes. General help, only for Status Page Setup Menu and Option Page Setup Menu. Change color from total colors. Reserved. Reserved. Restore the previous CMOS value from CMOS, only for Option Page Setup Menu. Load the default CMOS value from BIOS default table, only for Option Page Setup Menu. Load the default. Reserved. Reserved. Save all the CMOS changes, only for Main Menu. -

60 BIOS Configuration.. GETTING HELP... Main Menu The on-line description of the highlighted setup function is displayed at the bottom of the screen.... Status Page Setup Menu / Option Page Setup Menu Press F to pop up a small help window that describes the appropriate keys to use and the possible selections for the highlighted item. To exit the Help Window press <Esc>... THE MAIN MENU Once you enter AMI BIOS CMOS Setup Utility, the Main Menu (Figure.) will appear on the screen. The Main Menu allows you to select setup functions and exit choices. Use arrow keys to select among the items and press <Enter> to accept or enter the sub-menu. Standard CMOS setup Figure.: Main Menu This setup page includes all the items in a standard compatible BIOS. BIOS features setup This setup page includes all the items of Award special enhanced features. -

61 AA Chipset features setup This setup page includes all the items of chipset special features. Power management setup This setup page includes all the items of Green function features. PNP/PCI configuration This setup page includes all the items of PNP/PCI configuration features. Load BIOS defaults BIOS defaults indicates the most appropriate value of the system parameter which the system would be in safe configuration. Load setup defaults Setup Defaults indicates the value of the system parameters that the system would be in the best performance configuration. Integrated Peripherals This setup page includes all the items of peripherals features. Supervisor Pasord Change, set, or disable pasord. It allows you to limit access to the system and Setup, or just to Setup. User Pasord Change, set, or disable pasord. It allows you to limit access to the system. IDE HDD auto detection Automatically configure hard disk parameter. Save & exit setup Save CMOS value changes to CMOS and exit setup. Exit without save Abandon all CMOS value changes and exit setup. -

62 BIOS Configuration.. STANDARD CMOS SETUP MENU The items in Standard CMOS Setup Menu (Figure.) are divided into 9 categories. Each category includes no, one or more than one setup items. Use the arrows to highlight the item and then use the <PgUp> or <PgDn> keys to select the value you want in each item. Date Figure.: Standard CMOS Setup Menu The date format is <week>, <month> <day> <year>. Press <F> to show the calendar. Week The day, from Sun to Sat, determined by the BIOS and is display-only Month The month, Jan. through Dec. Day The date, from to (or the maximum allowed in the month) Year The year, from 99 through 09 -

63 AA Time The time format in <hour> <minute> <second>. The time is calculated base on the -hour military-time clock. For example, p.m. is :00:00. Primary HDDs / Secondary HDDs The category identify the types of hard disk from drive C to drive F devices that has been installed in the computer. There are three options for definable type; User, Auto and None. Type User is user-definable; and type Auto means automatically detecting HDD's type and None means No IDE HDD installed. If you select Type User, related information is asked to be entered to the following items. Enter the information directly from the keyboard and press <Enter>. Those information should be provided in the documentation from your hard disk vendor or the system manufacturer. CYLS. HEADS PRECOMP LANDZONE SECTORS number of cylinders number of heads write precomp landing zone number of sectors If a hard disk has not been installed select NONE and press <Enter>. -

64 BIOS Configuration Drive A type / Drive B type The category identify the types of floppy disk drive A or drive B that has been installed in the computer. None No floppy drive installed 0K,. in. -/ inch PC-type standard drive; 0 kilobyte capacity..m,. in. -/ inch AT-type high-density drive;. megabyte capacity (-/ inch when Mode is Enabled). 0K,. in. -/ inch double-sided drive; 0 kilobyte capacity.m,. in. -/ inch double-sided drive;. megabyte capacity..m,. in. -/ inch double-sided drive;. megabyte capacity. Memory The category is display-only which is determined by POST (Power On Self Test) of the BIOS. Base Memory The POST of the BIOS will determine the amount of base (or conventional) memory installed in the system. The value of the base memory is typically K for systems with K memory installed on the motherboard, or 0 K for systems with 0 K or more memory installed on the motherboard. Extended Memory The BIOS determines how much extended memory is present during the POST. This is the amount of memory located above MB in the CPU's memory address map. -

65 AA Expanded Memory Expanded Memory in memory defined by the Lotus / Intel / Microsoft (LIM) standard as EMS. Many standard DOS applications can not utilize memory above 0, the Expanded Memory Specification (EMS) aps memory which not utilized by DOS with a section, or frame, so these applications can access all of the system memory. Memory can be apped by EMS is usually K within MB or memory above MB, depends on the chipset design. Expanded memory device driver is required to use memory as Expanded Memory. Other Memory This refers to the memory located in the 0 to 0 address space. This is memory that can be used for different applications. DOS uses this area to load device drivers to keep as much base memory free for application programs. Most use for this area is Shadow RAM. -

66 BIOS Configuration.. BIOS FEATURES SETUP st / nd / rd / th Boot Device Figure.: BIOS Features Setup The default value is Floppy or LS/ZIP A: or ATAPI ZIP C: or CDROM or SCSI or NETWORK or IDE-0~IDE- or Disabled. Floppy LS/ZIP A: ATAPI ZIP C: CDROM SCSI NETWORK IDE-0~IDE- Disabled Try Other Boot Devices The default value is Yes. Yes No Boot Device by Floppy. Boot Device by LS/ZIP A:. Boot Device by ATAPI ZIP C:. Boot Device by CDROM. Boot Device by SCSI. Boot Device by NETWORK. Boot Device by IDE-0~IDE-. Boot Device by Disabled. Enable Try Other Boot Devices function. Disable Try Other Boot Devices function. -9

67 AA Quick Boot The default value is Disabled. Enabled Disabled Bootup Num-Lock Default value is On. On Off Floppy Drive Swap Enabled Quick Boot Function. Disabled Quick Boot Function. Keypad is number keys. Keypad is arrow keys. The default value is Disabled. Enabled Disabled Floppy Drive Seek Floppy A & B will be apped under DOS. Floppy A & B will be normal definition. During POST, BIOS will determine if the floppy disk drive installed is 0 or 0 tracks. 0 type is 0 tracks while 0,. and. are all 0 tracks. The default value is Enabled. Enabled BIOS searches for floppy disk drive to determine if it is 0 or 0 tracks. Note that BIOS can not tell from 0,. or. drive type as they are all 0 tracks. Disabled BIOS will not search for the type of floppy disk drive by track number. Note that there will not be any warning message if the drive installed is 0. Floppy Access Control The default value is Normal. Normal Read Only Set Floppy Access Control : Normal. Set Floppy Access Control : Read Only. -0

68 BIOS Configuration HDD Access Control The default value is Normal. Normal Read Only PS/ Mouse Support Set HDD Access Control : Normal. Set HDD Access Control : Read Only. The default value is Enabled. Enabled Disabled Primary Display Enabled PS/ Mouse Support Function. Disabled PS/ Mouse Support Function. The default value is VGA / EGA. VGA / EGA Set Primary Display to VGA / EGA. CGA 0x Set Primary Display to CGA 0x. CGA 0x Set Primary Display to CGA 0x. Mono Set Primary Display to Mono. Absent Set Primary Display to Absent. Pasord Check The default value is Setup. Setup Always Parity Check Set Pasord Check to Setup. Set Pasord Check to Always. The default value is Disabled. Enabled Disabled Boot To OS/ The default value is No. Yes No Enabled Parity Check Function. Disabled Parity Check Function. Enabled Boot To OS/. Disabled Boot To OS/. -

69 AA Internal Cache The default value is Enabled. Enabled Disabled External Cache Enabled Internal Cache Function. Disabled Internal Cache Function. The default value is Enabled. Enabled Disabled System BIOS Cacheable Enabled External Cache Function. Disabled External Cache Function. The default value is Disabled. Enabled Disabled Video BIOS Shadow Enabled System BIOS Cacheable. Disabled System BIOS Cacheable. It determines whether video BIOS will copied to RAM, however, it is optional from chipset design. Video Shadow will increase the video speed. The default value is Enabled. Enabled Disabled Cached Video shadow is enabled. Video shadow is disabled. Video shadow is cached. C00, k Shadow / D000, k Shadow These categories determine whether optional ROM will be copied to RAM by byte. The default value are Disabled. Enabled Disabled Cached Optional shadow is enabled. Optional shadow is disabled. Optional shadow is cached. -

70 BIOS Configuration.. CHIPSET FEATURES SETUP USB Function The default value is Enabled. Enabled Disabled USB Legacy Support. Figure.: Chipset Features Setup Enabled USB Function. Disabled USB Function. The default value is Disabled. Enabled Disabled SDRAM CAS Latency The default value is Auto. Enabled USB Legacy Support Function. Disabled USB Legacy Support Function. For Slower SDRAM DIMM module. For Fastest SDRAM DIMM module. CAS latency time will be set automatically if you have Auto SPD on SDRAM. -

71 AA DRAM Data Integrity Mode The default value is Parity. ECC Set DRAM Data Integrity Mode to ECCMode. Parity Set DRAM Data Integrity Mode to ParityMode. SDRAM Burst Mode The default value is Enabled. Enabled Enabled SDRAM Burst X Disabled Disabled SDRAM Burst X DRAM Timing The default value is Normal. Normal For normal DRAM timing operation. Fast For Fastest DRAM timing operation. Slow For Slower DRAM timing operation. Pipe Function The default value is Enabled. Enabled Enabled Pipe Function. Disabled Disabled Pipe Function. Gated Clock The default value is Disabled. Enabled Enabled Gated Clock Function. Disabled Disabled Gated Clock Function. -

72 BIOS Configuration Graphics Aperture Size The default value is MB. M Set Graphics Aperture Size to MB. M Set Graphics Aperture Size to MB. MB Set Graphics Aperture Size to MB. MB Set Graphics Aperture Size to MB. MB Set Graphics Aperture Size to MB. MB Set Graphics Aperture Size to MB. MB Set Graphics Aperture Size to MB. Primary Frame Buffer The default value is All. All Set Primary Frame Buffer to All. MB Set Primary Frame Buffer to MB. MB Set Primary Frame Buffer to MB. MB Set Primary Frame Buffer to MB. MB Set Primary Frame Buffer to MB. MB Set Primary Frame Buffer to MB. Disabled Disabled Primary Frame Buffer. VGA Frame Buffer The default value is Enabled. Enabled Enable VGA Frame Buffer. Disabled Disable VGA Frame Buffer. Data Merge The default value is Disabled. Enabled Enable Data Merge. Disabled Disable Data Merge. -

73 AA Passive Release The default value is Enabled. Enabled Enable Passive Release. Disabled Disable Passive Release. ISA Line Buffer The default value is Enabled. Enabled Enable ISA Line Buffer. Disabled Disable ISA Line Buffer. Delay Transaction The default value is Disabled. Enabled Enable Delay Transaction. Disabled Disable Delay Transaction. AT Bus Clock The default value is Auto..9MHz Set AT Bus Clock to.9mhz. PCICLK/ Set AT Bus Clock to PCICLK/. PCICLK/ Set AT Bus Clock to PCICLK/. PCICLK/ Set AT Bus Clock to PCICLK/. PCICLK/ Set AT Bus Clock to PCICLK/. PCICLK/ Set AT Bus Clock to PCICLK/. Auto Set AT Bus Clock to Auto. AMD K Write Allocate The default value is Disabled. Enabled Enabled AMD K Write Allocate. Disabled Disabled AMD K Write Allocate. -

74 BIOS Configuration Spread Spectrum The default value is Disabled. Disabled Normal. 0.%(CNTR) Set Spread Spectrum 0.%( Center Spread)... POWER MANAGEMENT SETUP Figure.: Power Management Setup *These four items will be available when RTC Alarm Resume is set to Enabled. Power Management / APM The default value is Enabled. Enabled Disabled Enable Green function. Disable Green function. Green Monitor Power State The default value is Off. Off Stand By Suspend Set Green Monitor Power State to Off. Set Green Monitor Power State to Stand By. Set Green Monitor Power State to Suspend. -

75 AA Video Power Down Mode The default value is Stand By. Disabled Disabled Video Power Down Mode Function. Stand By Set Video Power Down Mode to Stand By. Suspend Set Video Power Down Mode to Suspend. Hard Disk Power Down Mode The default value is Disabled. Disabled Disabled Hard Disk Power Down Mode Function. Stand By Set Hard Disk Power Down Mode to Stand By. Suspend Set Hard Disk Power Down Mode to Suspend. Standby Time Out The default value is Disabled. Disabled Disabled Standby Time Out Function. min Enabled Standby Time Out between min. min Enabled Standby Time Out between min. 0min Enabled Standby Time Out between 0min. 0min Enabled Standby Time Out between 0min. hr Enabled Standby Time Out between hr. hr Enabled Standby Time Out between hr. hr Enabled Standby Time Out between hr. Suspend Time Out The default value is Disabled. Disabled Disabled Suspend Time Out Function. min Enabled Suspend Time Out between min. min Enabled Suspend Time Out between min. 0min Enabled Suspend Time Out between 0min. 0min Enabled Suspend Time Out between 0min. hr Enabled Suspend Time Out between hr. hr Enabled Suspend Time Out between hr. hr Enabled Suspend Time Out between hr. -

76 BIOS Configuration Monitor Parallel Port The default value is Yes. Yes Enabled Monitor Parallel Port Function. No Disabled Monitor Parallel Port Function. Monitor Serial Port The default value is Yes. Yes Enabled Monitor Serial Port Function. No Disabled Monitor Serial Port Function. Monitor Floppy The default value is Yes. Yes Enabled Monitor Floppy Function. No Disabled Monitor Floppy Function. Monitor VGA The default value is No. Yes Enabled Monitor VGA Function. No Disabled Monitor VGA Function. Monitor Audio The default value is No. Yes Enabled Monitor Audio Function. No Disabled Monitor Audio Function. Monitor Pri-HDD The default value is Yes. Yes Enabled Monitor Pri-HDD Function. No Disabled Monitor Pri-HDD Function. -9

77 AA Monitor Sec-HDD The default value is No. Yes No Power Button Function The default value is Soft Off. Soft Off Suspend MODEM Use IRQ The default value is. Enabled Monitor Sec-HDD Function. Disabled Monitor Sec-HDD Function. Set Power Button Function to Soft Off. Set Power Button Function to Delay sec. NA Set MODEM Use IRQ to NA. Set MODEM Use IRQ to. Set MODEM Use IRQ to. Set MODEM Use IRQ to. Set MODEM Use IRQ to. 9 Set MODEM Use IRQ to 9. 0 Set MODEM Use IRQ to 0. Set MODEM Use IRQ to. LAN / Modem Ring On The default value is Disabled. Enabled Disabled Enable Ring Resume From Soft Off function. Disable Ring Resume From Soft Off function. -0

78 BIOS Configuration RTC Alarm Resume The default value is Disabled. Enabled Disabled Enable RTC Alarm Resume function. Disable RTC Alarm Resume function. If RTC Alarm Resume is Enabled. Date Alarm : Every Day,~ Hour Alarm : 0~ Minute Alarm : 0~9 Second Alarm : 0~9 -

79 AA.9. PNP/PCI CONFIGURATION * * Figure.: PCI Slot Configuration *These two items will be available when OffBoard PCI IDE Card is set to Slot. Plug and Play Aware O/S The default value is No. Yes No Clear NVRAM The default value is No. Yes No Enable Plug and Play Aware O/S function. Disable Plug and Play Aware O/S function. Enable Clear NVRAM function. Disable Clear NCRAM function. -

80 BIOS Configuration PCI Latency Timer The default value is. Set PCI Latency Timer to. Set PCI Latency Timer to. 9 Set PCI Latency Timer to 9. Set PCI Latency Timer to. 0 Set PCI Latency Timer to 0. 9 Set PCI Latency Timer to 90. Set PCI Latency Timer to. Set PCI Latency Timer to. Primary Graphics Adapter The default value is PCI. PCI AGP PCI VGA Palette Snoop Set Primary Graphics Adapter to PCI. Set Primary Graphics Adapter to AGP. The default value is Disabled. Enabled Disabled OffBoard PCI IDE Card Enabled PCI VGA Palette Snoop Function. Disabled PCI VGA Palette Snoop Function. The default value is Auto. Auto Set OffBoard PCI IDE Card to Auto. Slot Set OffBoard PCI IDE Card to Slot. Slot Set OffBoard PCI IDE Card to Slot. Slot Set OffBoard PCI IDE Card to Slot. -

81 AA OffBoard PCI IDE Pri.IRQ The default value is Disabled. Disabled Disabled OffBoard PCI IDE Pri.IRQ. INTA Set OffBoard PCI IDE Pri.IRQ to INTA. INTB Set OffBoard PCI IDE Pri.IRQ to INTB. INTC Set OffBoard PCI IDE Pri.IRQ to INTC. INTD Set OffBoard PCI IDE Pri.IRQ to INTD. Hardwired Set OffBoard PCI IDE Pri.IRQ to Hard wired. OffBoard PCI IDE Sec.IRQ The default value is Disabled. Disabled Disabled OffBoard PCI IDE Sec.IRQ. INTA Set OffBoard PCI IDE Sec.IRQ to INTA. INTB Set OffBoard PCI IDE Sec.IRQ to INTB. INTC Set OffBoard PCI IDE Sec.IRQ to INTC. INTD Set OffBoard PCI IDE Sec.IRQ to INTD. Hardwired Set OffBoard PCI IDE Sec.IRQ to Hard wired. Assign IRQ to PCI VGA The default value is Yes. Yes No Enabled Assign IRQ to PCI VGA Function. Disabled Assign IRQ to PCI VGA Function. PCI Slot / Slot / Slot IRQ Priority The default value is Auto. ~ Set PCI Slot / Slot / Slot IRQ Priority between to. Auto Set PCI Slot / Slot / Slot IRQ Priority to Auto. DMA Channel (0,,,,,) The default value is PnP. ISA/EISA PnP The resource is used by ISA/EISA device. The resource is used by PnP device. -

82 BIOS Configuration IRQ (,,,,9,0,,,,) The default value is "ISA/EISA" or "PCI/PnP". ISA/EISA PCI/PnP The resource is used by ISA/EISA device. The resource is used by PCI/PnP device..0. LOAD BIOS DEFAULTS Load BIOS Defaults Figure.: Load BIOS Defaults To load BIOS defaults value to CMOS RAM, enter "Y". If not, enter "N". -

83 AA.. LOAD SETUP DEFAULTS Load SETUP Defaults Figure.: Load Setup Defaults To load SETUP defaults value to CMOS RAM, enter "Y". If not, enter "N". If there is any problem occurred, loading BIOS DEFAULTS step is recommended. -

84 BIOS Configuration.. INTEGRATED PERIPHERALS Figure.9: Integrated peripherals These two items will Enabled when OnBoard Serial Port is set to Enabled. **The item will Enable when Parallel Port Mode is set to ECP # These two items will show up when KeyBoard PowerOn is set to Enabled OnBoard FDC The default value is Enabled. Enabled Enabled OnBoard FDC Function. Disabled Disabled OnBoard FDC Function. Auto Set OnBoard FDC Function is Auto. -

85 AA OnBoard Serial Port The default value is Fh/COM. Auto BIOS will automatically setup the port address. Fh/COM Enable OnBoard Serial port and address is Fh. Fh/COM Enable OnBoard Serial port and address is Fh. Eh/COM Enable OnBoard Serial port and address is Eh. Eh/COM Enable OnBoard Serial port and address is Eh. Disabled Disable OnBoard Serial port. OnBoard Serial Port The default value is Fh/COM. Auto BIOS will automatically setup the port address. Fh/COM Enable OnBoard Serial port and address is Fh. Fh/COM Enable OnBoard Serial port and address is Fh. Eh/COM Enable OnBoard Serial port and address is Eh. Eh/COM Enable OnBoard Serial port and address is Eh. Disabled Disable OnBoard Serial port. OnBoard Serial Port The default value is Disabled. Auto BIOS will automatically setup the port address. Fh/COM Enable OnBoard Serial port and address is Fh. Fh/COM Enable OnBoard Serial port and address is Fh. Eh/COM Enable OnBoard Serial port and address is Eh. Eh/COM Enable OnBoard Serial port and address is Eh. Disabled Disable OnBoard Serial port. Serial Port Mode The default value is N/A. FIR Onboard I/O chip supports FIR. IrDA Onboard I/O chip supports IrDA. ASKIR Onboard I/O chip supports ASKIR. -

86 BIOS Configuration Serial Port IRQ The default value is N/A. Set Serial Port IRQ to. Set Serial Port IRQ to. Set Serial Port IRQ to. 9 Set Serial Port IRQ to 9. 0 Set Serial Port IRQ to 0. Set Serial Port IRQ to. Serial Port DMA The default value is N/A. Set Serial Port DMA to. Set Serial Port DMA to. OnBoard Parallel port The default value is h. h Enable onboard LPT port and address is h. h Enable onboard LPT port and address is h. BCh Enable onboard LPT port and address is BCh. Auto Set OnBoard LPT port is Auto. Disabled Disable onboard LPT port. Parallel Port Mode The default value is SPP. SPP ECP EPP ECP+EPP Using Parallel port as Standard Parallel Port. Using Parallel port as Extended Capabilities Port. Using Parallel port as Enhanced Parallel Port. Using Parallel port as ECP & EPP mode. Parallel Port IRQ The default value is. Set Parallel Port IRQ to. Set Parallel Port IRQ to. -9

87 AA Parallel Port DMA Channel The default value is N/A. Set Parallel Port DMA Channel to. Set Parallel Port DMA Channel to. KeyBoard PowerOn The default value is Disabled. Enabled Disabled PowerOn Select Enabled KeyBoard PowerOn. Disabled KeyBoard PowerOn. The default value is N/A. Hot Key KB PWR ON/OFF Function Set Enabled, KB PWR ON/OFF Pasord : Enter will show up. When users enabled KB PWR ON/OFF Function, please set pasord with three different characters, and press the three different characters pasord at the same time. For example, if users set abc as pasord, then he would press a b c at the same time. (a-b-c is hot key). Pass Word You can power on your system by entering the keyboard power on pasord. If your pasord consists of more than one character, you have to press the ENTER key after entering the pasord. HotKey Select The default value is N/A. Ctrl-Alt-F~F Set HotKey Select Function to Ctrl-Alt-F~F. Ctrl-Alt-Ins Set HotKey Select Function to Ctrl-Alt-Ins. Ctrl-Alt-Del Set HotKey Select Function to Ctrl-Alt-Del. Ctrl-Alt-LShift Set HotKey Select Function to Ctrl-Alt-LShift. Ctrl-Alt-RShift Set HotKey Select Function to Ctrl-Alt-RShift. -0

88 BIOS Configuration OnBoard IDE The default value is Both. Both Set OnBoard IDE is Both. Disabled Disabled OnBoard IDE Function. Primary Set OnBoard IDE is Primary. Secondary Set OnBoard IDE is Secondary. -

89 AA..SUPERVISOR / USER PASSWORD When you select this function, the following message will appear at the center of the screen to assist you in creating a pasord. Figure.0: Pasord Setting Type the pasord, up to eight characters, and press <Enter>. The pasord typed now will clear previously entered pasord from CMOS memory. You will be asked to confirm the pasord. Type the pasord again and press <Enter>. You may also press <Esc> to abort the selection and not enter a pasord. To disable pasord, just press <Enter> when you are prompted to enter pasord. A message will confirm the pasord being disabled. Once the pasord is disabled, the system will boot and you can enter Setup freely. PASSWORD DISABLED If you select System at Security Option of BIOS Features Setup Menu, you will be prompted for the pasord every time the system is rebooted or any time you try to enter Setup. If you select Setup at Security Option of BIOS Features Setup Menu, you will be prompted only when you try to enter Setup. -

90 BIOS Configuration.. IDE HDD AUTO DETECTION Figure.: IDE HDD Auto Detection The screen will display the Standard CMOS Setup once you enter the menu. User won t need to make any changes to items in the menu. The system will auto detect the HDD and save it in the CMOS setup menu. -

91 AA.. SAVE & EXIT SETUP Figure.: Save & Exit Setup Type "Y" will quit the Setup Utility and save the user setup value to RTC CMOS RAM. Type "N" will return to Setup Utility. -

92 BIOS Configuration.. EXIT WITHOUT SAVING Figure.: Exit Without Saving Type "Y" will quit the Setup Utility without saving to RTC CMOS RAM. Type "N" will return to Setup Utility. -