ACE-B5692 Quick Manual

Transcription

1 1. Mainboard illustration (Top Side) 2. Mainboard illustration (Bottom Side) 1 P/N: G 2 P/N: G

2 1 JP21 ibutton option pin header 2 CN19 Reel connector 3 U83 ibutton holder 4 JP19 PIC programming pin header 5 CN14 I2C pin header 6 JP8 CF voltage select 7 IDE1 44pin IDE Connector 8 CN9 CPLD programming pin header 9 USB2 2 header for 4 USB ports 10 USB3 2 header for 4 USB ports JP7 11 Beep/reset/power button/power LED BAT2 12 BAT2 is rechargeable battery connector for SRAM2/AGA BAT1 13 BAT1 is rechargeable battery connector for SRAM1/AGA JP9/JP10/JP12/JP13 JP13:SRAM2 clear pin header JP12:SRAM1 clear pin header 14 JP9: CF Master/Slave pin header JP10:IDE DMA 33/66 select pin header 15 JP4 Clear COMS pin header SW7 16 Bill and Coin enable pre-set dip Switch 17 CN3 System Reset header 18 JP14 Audio with AMP or without AMP 19 JP15 Audio with AMP or without AMP 20 SATA3 Standard 7-pin SATA connector 21 SATA1 Standard 7-pin SATA connector 22 CN6 SATA power pin 23 CN1 CR2032 Size Coin Battery 24 FAN2 FAN2 is for system fan 25 J2 240 DDR2 DIMM socket 26 J1 240 DDR2 DIMM socket 27 JP1 28 JP2 29 JP3 30 DVI1 DVI-I pin header 31 PCIE_1 PCI Express 16X slot 32 USB4 bnand USB Dongle header 33 SW8 Intrusion log switch 34 KBMS1 Keyboard/Mouse pin header(option) 35 CN4 Keyboard lock 36 FAN1 FAN1 is for CPU USB1 37 LAN RJ45 with two USB connector 38 JP17 cctalk voltage selector(com3) 39 cctalk1 cctalk connector.(com3) 40 JP18 cctalk voltage selector (COM4) 41 SW2 Software readable switch 42 cctalk2 cctalk connector.(com4) 43 SW1 Software readable switch 44 CN18 COM6 pin header 45 SW6 Select COM4 is RS-232 or cctalk 46 CN17 COM4 pin header 47 SCN1 VGA connector 48 SW5 Select COM3 is RS-232 or cctalk 49 CN16 COM3 pin header 50 CN15 COM2 pin header 51 COM1 COM1 RS-232 connector 52 CN5 CF card slot 3. Connectors and Jumper Setting 2.1 JP21 (ibutton option) 2.2 CN19 (Reel / GPIO 2.3 U83 (ibutton holder) 1-2 description disable enable Signal I/O Type Signal I/O Type 1 K1 I/O 2 K0 I/O 3 K3 I/O 4 K2 I/O 5 K5 I/O 6 K4 I/O 7 K7 I/O 8 K6 I/O 9 GND 10 GND 11 L1 I/O 12 L0 I/O 13 L3 I/O 14 L2 I/O 15 L5 I/O 16 L4 I/O 17 L7 I/O 18 L6 I/O 19 GND 20 GND 21 D5 I 22 D6 I 23 D7 I 24 E4 I/O 25 E5 I/O 26 E6 I/O 27 E7 I/O 28 GND 29 GND 30 I5 O 31 I6 O 32 I7 O V V Note: GPIO is standard CMOS 3.3V Input/Output ibutton holder for DS1994 IC. 2.4 JP19 (PIC 2.6 JP8 (CF voltage 2.5 CN14 (I2C pin header) programming pin header) select) 1 VDD 2 DATA 3 CLK 4 MCLR 5 GND 1 Vcc 2 CLK 3 DATA 4 GND discripti V V 3 P/N: G 4 P/N: G

3 2.7 IDE1 (44 IDE 2.8 CN9 (CPLD programming pin header) 2.9/2.10 USB2/3 (2 pin header for 4 USB ports) 2.15 JP4 (clear CMOS pin header) 2.16 SW7 (Bill and Coin enable pre-set dip switch) 2.17 CN3 (System reset pin header) signal signal State 1 RESET 2 GND 3 D7 4 D8 5 D6 6 D9 7 D5 8 D10 9 D4 10 D11 descript 1-2 normal 2-3 clear 1(BILL) 2(COIN) ON OFF ON pre-set is Low pre-set is High pre-set is Low 1-2 normal reset 11 D3 12 D12 13 D2 14 D13 15 D1 16 D14 17 D0 18 D15 19 GND 20 NC 21 DREQ 22 GND 23 IOW# 24 GND 25 IOR# 26 GND TDO 3 TDI 4 NC 5 NC 6 TMS signal signal 1 +5V 2 +5V 3 USB_A 4 USB_B 5 USB_A 6 USB_B 7 GND 8 GND C OS 2.18/2.19 JP14/15 (Audio with AMP or without AMP) OFF pre-set is High 2.20/2.21 SATA1/3 (Stander 7-pin SATA 2.22 CN6 (SATA power 27 IORDY 28 GND 29 DACK# 30 GND 31 IDEIR 32 NC 33 A1 34 PDIAG 35 A0 36 A2 37 DCS1# 38 CS3 39 IDE_L 40 GND 41 +5V 42 +5V 7 GND 8 TCK 9 GND 10 GND 1-3, , 4-6 with amplifier without amplifier SATA connector discriptio 1 +12V 2 GND V 4 +5V 43 GND 44 NC 2.11 JP7 (beep/reset/power button/power LED) 2.12/2.13 BAT1/2 (Battery 2.14 JP9/10/11/12/13 (For CF/ IDE/ SRAM1/ SRAM2) 2.23 CN1 (battery holder) 2.24/2.36 FAN1/2 (FAN 2.25/2.26 J1/J2 (240pin DDR2 SRAM socket) 1-2 JP9 JP10 sign signal 1 +5V 2 PC 3 GND 4 RESE 5 GND 6 POW 7 GND 8 +5V_S descriptions V 2 GND Slaver DMA 33 Master DMA 66 JP13 JP normal normal 2-3 clear SRAM2 clear SRAM1 Battery holder for CR2032 Size Coin Battery. 1 GND 2 +12V 3 Detect fan speed signal 240 pin DDR2 SRAM socket #Note: If using only one DDR2 DIMM module on system board. Please, first insert it into J2 socket. Don t inset it to J1. 5 P/N: G 6 P/N: G

4 2.27/2.28/2.29 JP1/JP2/JP3 (FSB setting) 2.30 DVI1 (DVI-I pin header) 1 GND 14 TDC0+ 2 TDC0-15 GND 3 TDC1+ 16 TDC1-4 GND 17 TDC2+ JP1 JP2 JP3 5 TDC2-18 GND auto setting 6 TLC+ 19 TLC- 7 DVI DETECT 20 SC DDC DVI Mhz 8 +5V 21 SD DDC DVI Mhz 9 RED 22 GND 10 GREEN 23 GND 11 BLUE 24 GND 12 VSYNC 25 MONSCL 2.38/2.40 JP17(for cctalk1)/jp18(for cctalk2) (cctalk voltage select) description V V 2.39/2.42 cctalk1(com3)/cctalk2( COM4) (cctalk 1 JP17/18 select 2 NC 3 COM 4 DATA 2.41/2.43 SW2/SW1 (software readable switch) descriptio ON GND OFF +3.3V 13 HSYNC 26 MONSDA #Note: Only VGA out, the DVI out is function Option (Grey) 2.31 PCIE_1 (PCI-E 16X socket) 2.32 USB4 ( header for bnand USB dongle) 2.33 SW8 (intrusion log switch) 2.44/2.46/2.49/2.50 CN18(COM6)/CN17(COM4)/CN16(COM 3)/CN15(COM2) (COM Port) #COM6 for Card Reader 2.47 SCN1 (VGA 2.51 COM1 (COM port 1 +5V 2 NC PCI-E 16X slot 3 USBC- 4 NC 5 USBC+ 6 NC 7 GND 8 NC 9 NC 10 NC Intrusion log switch for AGC Port A bit7 1 DCD 2 DSR 3 RX 4 RTS 5 TX 6 CTS 7 DTR 8 RI 9 GND 10 NC(+5V for VGA connector COM port connector 2.34 KBMS1(keyboard/mouse pin header)-- option 2.35 CN4 (keyboard lock) 2.37 USB1 (one RJ45 with two USB 2.45/2.48 SW5/6 (select COM4/COM3 is RS-232 or cctalk) 2.52 CF1 (Compare flash) 1 mouse data 2 keyboard 3 GND 4 +5V 5 mouse clock 1- discriptio lock normal One RJ45 with two layer USB connector 1-2, ,4-6 RS-232 mode cctalk mode Compact flash socket 6 keyboard 7 P/N: G 8 P/N: G

5 JAMMA Golden Finger I: Spare I/O Input O: Spare I/O Output I/O: Spare Input/Output I.I: Isolated Input I and I.P.H: Input and Internal Pull High O.D.: Open Drain Output A.O: Analog Output A.P: Analog Power P: Power I/O TYPE Port/Bit Function I/O TYPE Port/Bit Function A1 P GND B1 P GND A2 P GND B2 P GND A3 P Power +5V B3 P Power +5V A4 P Power +5V B4 P Power +5V A5 P +24v for cctalk B5 P +24V for cctalk A6 P Power +12V B6 P Power +12V A7 I and I.P.H. A0 Intrusion 0 A8 I and I.P.H A2 Intrusion 2 B7 I and I.P.H A1 Intrusion 1 B8 O.D H0 Output Counter A9 N/C N/C B9 O.D H4 Input Counter A10 A.O Speaker Left B10 A.P Audio GND A11 A.O Speaker Right B11 A.P Audio GND A12 N/C N/C B12 O.D G3 Tower Lamp 3 A13 N/C N/C B13 N/C N/C A14 N/C N/C B14 I.I D1 Test Switch A15 I.I B7 Button8 B15 O.D F7 Lamp8 A16 I.I B6 Button7 B16 O.D F6 Lamp7 A17 I.I B5 Button6 B17 O.D F5 Lamp6 A18 I.I B2 Button3 B18 O.D F2 Lamp3 A19 I.I B3 Button4 B19 O.D F3 Lamp4 A20 I.I B1 Button2 B20 O.D F1 Lamp2 A21 I.I B0 Button1 B21 O.D F0 Lamp1 A22 I.I B4 Button5 B22 O.D F4 Lamp5 A23 I.I C0 Button Start B23 O.D I3 Lamp Start A24 I.I D2 REFILL Key B24 O.D H2 REFILL Counter A25 O.D G1 Tower Lamp 1 B25 DBIO COM3 DBIO A26 O.D G2 Tower Lamp 2 B26 N/C N/C A27 P GND B27 P GND A28 P GND B28 P GND 9 P/N: G