STC Gigabit XENPAK 40km Transceiver

Transcription

1 STC00 0 Gigabit XENPAK 0km Transceiver FEATURES XAU Electrical nterface: Cooled 0nm EML TSA Hot ZPluggable SCDuplex ptical Receptacle MD, DM Support Pin Photodetector Compliant to XENPAK MSA Mechanical Footprint:. L x. W x 0. H Compliant to EEE 0.ae 0GBASEER Application Case operating temperature: 0 to 0 C REFERENCE EEE 0.ae as 0GBASEER, XENPAK MSA Release.0 GENERAL DESCRPTN Swedish Telecom 0Gb/s XENPAK transceiver module STC00 is a hot pluggable in the Zdirection module that is usable in typical router line card applications, Storage, P network and LAN and compliant to XENPAK MSA. The STC00 is a fully integrated 0.Gbit/s optical transceiver module that consists of a 0.Gbit/s optical transmitter and receiver, XAU interface, Mux and Demux with clock and data recovery(cdr).this version of Swedish Telecom nc. transceiver line uses an cooled 0nm EML Laser Diode to achieve 0km over standard single mode fiber as 0GBASEER of the EEE 0.ae. Page

2 Ⅰ.ptical Characteristics Table. ptical Characteristics Parameters s Center Wavelength λc nm Signaling speed 0. Gbit/s Signaling speed variation from nominal ppm ptical modulation amplitude MA. ptical utput Power Pf + Side Mode Suppression Ratio SMSR 0 db Extinction Ratio Er. db ff Transmit Power Poff 0 9 Receiver Sensitivity Rsense. 0 Receiver verload Rro +0. Receiver Return Loss RL db Ⅱ.Electrical Performance Table. Power Characteristics Parameter oltage CC..00. oltage CC..00. Current CC. A Current CC. A Power Consumption PDS.0 W Power supply stabilization time TDF 00 ms nitialization Time TNT s RESET Assert Time TRESET ms 9 Hold Time after rising edge of RESET THLD 00 ms Table. XAU Driver Characteristics Parameter Baud Rate. Gbit/s Baud Rate Tolerance ppm Page

3 Differential Amplitude mpp, nearend value Table.. CMS nterface Characteristics Parameter nput High oltage H 0.. nput Low oltage L nput Pulldown Current n µa ih=. utput High oltage H.0 utput Low oltage L 0. Pullup=0k ohm to. Pull up Resistance RLAS 0 k ohm Capacitance CLAS 0 pf Load Capacitance CLoad 0 pf Table. MD Bidirectional nterface Characteristics Parameter nput High oltage HM 0.. nput Low oltage LM utput High oltage HM.0. utput Low oltage LM Pull up Resistance RMD 00 MDC min high/low time THM,TLM 0 ns MDC Frequency /TCK TBD. MHz Setup time TDS 0 ns 9 Hold time TDH 0 ns 0 MD output delay after rising edge of MDC TPD 0 00 ns nput Capacitance Ci 0 pf Bus Loading CL 0 pf hm Note: The maximum value of RMD depends on bus loading(cl), input capacitance(ci), and MDC frequency(/tck). Page

4 Ⅲ. Electrical Pad Layout Fig XENPAK Transponder Electrical Pad Layout Page

5 Table. XENPAK Pin Configuration Pin # RESERED.. APS APS / Logic 9 LAS pen Drain 0 RESET END SPECFC TX N/FF RESERED MD DETECT. CMS. CMS Description Electrical ground Electrical ground Electrical ground Power Power Adaptive Power Adaptive Power Link Alarm Status nterrupt. 0k ohm pull up on host. TX FF when MD RESET endor Specific Pin. Leave unconnected. Transmitter N/FF Pulled low inside module through k ohm. END SPECFC endor Specific Pin. Leave unconnected. END SPECFC endor Specific Pin. Leave unconnected. MD / pen Drain Management Data MDC. CMS Management Data Clock 9 PRTAD. CMS Port Address bit (Low=0) 0 PRTAD. CMS Port Address bit (Low=0) PRTAD. CMS Port Address bit (Low=0) PRTAD. CMS Port Address bit (Low=0) PRTAD0. CMS Port Address bit 0 (Low=0) END SPECFC endor Specific Pin. Leave unconnected. APS SET Feedback output for APS RESERED for Avalanche Photodiode use. APS SENSE Analog APS Sense Connection APS Adaptive Power 9 APS Adaptive Power 0. Power. Power RESERED RESERED 9 RESERED 0 Page

6 RX LANE 0+ Module XAU utput Lane 0+ RX LANE 0 Module XAU utput Lane 0 RX LANE + Module XAU utput Lane + RX LANE Module XAU utput Lane RX LANE + Module XAU utput Lane + RX LANE Module XAU utput Lane 9 0 RX LANE + Module XAU utput Lane + RX LANE Module XAU utput Lane TX LANE 0+ Module XAU nput Lane 0+ TX LANE 0 Module XAU nput Lane 0 TX LANE + Module XAU nput Lane + 9 TX LANE Module XAU nput Lane 0 TX LANE + Module XAU nput Lane + TX LANE Module XAU nput Lane TX LANE + Module XAU nput Lane + TX LANE Module XAU nput Lane RESERED RESERED 9 0 Note: Case is connected to electrical ground in the module. Page

7 Ⅳ.Package utline Figure Mechanical dimensions Ⅴ.Register Definition Device Address (Dec) Register Address (Hex) 0x0000 0x000 PMA/PMD PCS PHY XS PMA/PMD Control PMA/PMD Status PCS Control PCS Status 0x000 PMA/PMD Device dentifier0 PCS Device dentifier0 0x000 PMA/PMD Device dentifier PCS Device dentifier 0x000 PMA/PMD Speed Ability 0x000 PMA/PMD Device in Package 0x000 PMA/PMD Device in Package 0x000 0x000 0x0009 0x000A 0x000E 0x000F 0G PMA/PMD Control 0G PMA/PMD Status 0G PMD Transmit Disable 0G PMD Receive Signal.K. Package dentifier0 Package dentifier PCS Speed Ability PCS Device in Package PCS Device in Package PCS Control PCS Status 0x00 PHY XS Control PHY XS Status PHY XS Device dentifier0 PHY XS Device dentifier PHY XS Speed Ability PHY XS Device in Package PHY XS Device in Package PHY XS Status 0G PHY XGXS Lane Status Page

8 0x009 0x000 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x009 0x00A 0x00B 0x000 0x00 0x0D 0x0E0x0AD 0x0AE 0x0 0x9000 0x900 0x900 0x900 0x900 0x900 0x900 0x900 0xA000 0xA0 0xA00 0xA09 0xA0F 0xA00 0xA0 0xA0 0xA0 NR Control/Status (XENPAK Register) 0xA00 0G PHY XGXS Test Control 0GBASER PCS Status 0GBASER PCS Status 0GBASER PCS Test pattern Seed A0 0GBASER PCS Test pattern Seed A 0GBASER PCS Test pattern Seed A 0GBASER PCS Test pattern Seed A 0GBASER PCS Test pattern Seed B0 0GBASER PCS Test pattern Seed B 0GBASER PCS Test pattern Seed B 0GBASER PCS Test pattern Seed B 0GBASER PCS Test pattern Control 0GBASER PCS Test pattern Error counter NR (XENPAK Register) Customer AREA Specific Area(XENPAK Register) RX_ALARM Control (XENPAK Register) TX_ALARM Control (XENPAK Register) LAS Control (XENPAK Register) RX_ALARM Status (XENPAK Register) TX_ALARM Status (XENPAK Register) LAS Status (XENPAK Register) TX_FLAG Control Bits RX_FLAG Control Bits Alarm and Warning Thresholds Digital ptical Monitoring nterface DM Capability Extended TX_ALARM_FLAG Bits RX_ALARM_FLAG Bits TX_WARNNG_FLAG Bits RX_WARNNG_FLAG Bits ptional Digital ptical Monitoring (DM) Control/Status Page

9 Ⅵ. Regulatory Compliance Feature Reference Performance Electrostatic discharge ESD EC/EN 000 Compatible with standards Electromagnetic nterference (EM) Laser Eye Safety FCC Part Class B EN 0 Class B (CSPR A) FDA CFR 00.0, 00. EC/EN 0 Compatible with standards Class laser product RHS 00/9/EC Compatible with standards EMC EN000 Compatible with standards Appendix A. Document Revision ersion.0.0 Date Description Preliminary datasheet Update format and company s logo Page 9